NET: mvgbe: add phylib support
This add phylib support to the Marvell GBE driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
diff --git a/drivers/net/mvgbe.c b/drivers/net/mvgbe.c
index 47bf27c..4b58823 100644
--- a/drivers/net/mvgbe.c
+++ b/drivers/net/mvgbe.c
@@ -52,7 +52,7 @@
#define MV_PHY_ADR_REQUEST 0xee
#define MVGBE_SMI_REG (((struct mvgbe_registers *)MVGBE0_BASE)->smi)
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+#if defined(CONFIG_PHYLIB) || defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
/*
* smi_reg_read - miiphy_read callback function.
*
@@ -184,6 +184,25 @@
}
#endif
+#if defined(CONFIG_PHYLIB)
+int mvgbe_phy_read(struct mii_dev *bus, int phy_addr, int dev_addr,
+ int reg_addr)
+{
+ u16 data;
+ int ret;
+ ret = smi_reg_read(bus->name, phy_addr, reg_addr, &data);
+ if (ret)
+ return ret;
+ return data;
+}
+
+int mvgbe_phy_write(struct mii_dev *bus, int phy_addr, int dev_addr,
+ int reg_addr, u16 data)
+{
+ return smi_reg_write(bus->name, phy_addr, reg_addr, data);
+}
+#endif
+
/* Stop and checks all queues */
static void stop_queue(u32 * qreg)
{
@@ -467,8 +486,9 @@
/* Enable port Rx. */
MVGBE_REG_WR(regs->rqc, (1 << RXUQ));
-#if (defined (CONFIG_MII) || defined (CONFIG_CMD_MII)) \
- && defined (CONFIG_SYS_FAULT_ECHO_LINK_DOWN)
+#if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII)) && \
+ !defined(CONFIG_PHYLIB) && \
+ defined(CONFIG_SYS_FAULT_ECHO_LINK_DOWN)
/* Wait up to 5s for the link status */
for (i = 0; i < 5; i++) {
u16 phyadr;
@@ -647,6 +667,45 @@
return 0;
}
+#if defined(CONFIG_PHYLIB)
+int mvgbe_phylib_init(struct eth_device *dev, int phyid)
+{
+ struct mii_dev *bus;
+ struct phy_device *phydev;
+ int ret;
+
+ bus = mdio_alloc();
+ if (!bus) {
+ printf("mdio_alloc failed\n");
+ return -ENOMEM;
+ }
+ bus->read = mvgbe_phy_read;
+ bus->write = mvgbe_phy_write;
+ sprintf(bus->name, dev->name);
+
+ ret = mdio_register(bus);
+ if (ret) {
+ printf("mdio_register failed\n");
+ free(bus);
+ return -ENOMEM;
+ }
+
+ /* Set phy address of the port */
+ mvgbe_phy_write(bus, MV_PHY_ADR_REQUEST, 0, MV_PHY_ADR_REQUEST, phyid);
+
+ phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_RGMII);
+ if (!phydev) {
+ printf("phy_connect failed\n");
+ return -ENODEV;
+ }
+
+ phy_config(phydev);
+ phy_startup(phydev);
+
+ return 0;
+}
+#endif
+
int mvgbe_initialize(bd_t *bis)
{
struct mvgbe_device *dmvgbe;
@@ -729,7 +788,9 @@
eth_register(dev);
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
+#if defined(CONFIG_PHYLIB)
+ mvgbe_phylib_init(dev, PHY_BASE_ADR + devnum);
+#elif defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
miiphy_register(dev->name, smi_reg_read, smi_reg_write);
/* Set phy address of the port */
miiphy_write(dev->name, MV_PHY_ADR_REQUEST,