xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
diff --git a/arch/arm/dts/zynqmp-zcu106-revA.dts b/arch/arm/dts/zynqmp-zcu106-revA.dts
index 1dff845..971f76f 100644
--- a/arch/arm/dts/zynqmp-zcu106-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu106-revA.dts
@@ -137,6 +137,19 @@
compatible = "iio-hwmon";
io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>;
};
+
+ /* 48MHz reference crystal */
+ ref48: ref48M {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
+
+ refhdmi: refhdmi {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <114285000>;
+ };
};
&can1 {
@@ -147,6 +160,18 @@
status = "okay";
};
+&zynqmp_dpdma {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
+ <&psgtr 0 PHY_TYPE_DP 1 3>;
+};
+
+/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
@@ -490,8 +515,45 @@
#size-cells = <0>;
reg = <1>;
si5341: clock-generator@36 { /* SI5341 - u69 */
- compatible = "si5341";
+ compatible = "silabs,si5341";
reg = <0x36>;
+ #clock-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&ref48>;
+ clock-names = "xtal";
+ clock-output-names = "si5341";
+
+ si5341_0: out@0 {
+ /* refclk0 for PS-GT, used for DP */
+ reg = <0>;
+ always-on;
+ };
+ si5341_2: out@2 {
+ /* refclk2 for PS-GT, used for USB3 */
+ reg = <2>;
+ always-on;
+ };
+ si5341_3: out@3 {
+ /* refclk3 for PS-GT, used for SATA */
+ reg = <3>;
+ always-on;
+ };
+ si5341_6: out@6 {
+ /* refclk6 PL CLK125 */
+ reg = <6>;
+ always-on;
+ };
+ si5341_7: out@7 {
+ /* refclk7 PL CLK74 */
+ reg = <7>;
+ always-on;
+ };
+ si5341_9: out@9 {
+ /* refclk9 used for PS_REF_CLK 33.3 MHz */
+ reg = <9>;
+ always-on;
+ };
};
};
@@ -528,8 +590,23 @@
#size-cells = <0>;
reg = <4>;
si5328: clock-generator@69 {/* SI5328 - u20 */
- compatible = "silabs,si5328";
reg = <0x69>;
+ /*
+ * Chip has interrupt present connected to PL
+ * interrupt-parent = <&>;
+ * interrupts = <>;
+ */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+ clocks = <&refhdmi>;
+ clock-names = "xtal";
+ clock-output-names = "si5328";
+
+ si5328_clk: clk0@0 {
+ reg = <0>;
+ clock-frequency = <27000000>;
+ };
};
};
i2c@5 {
@@ -601,6 +678,13 @@
};
};
+&psgtr {
+ status = "okay";
+ /* nc, sata, usb3, dp */
+ clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+ clock-names = "ref1", "ref2", "ref3";
+};
+
&qspi {
status = "okay";
is-dual = <1>;
@@ -647,7 +731,7 @@
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
- phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
};
/* SD1 with level shifter */
@@ -660,10 +744,6 @@
xlnx,mio-bank = <1>;
};
-&serdes {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
@@ -681,8 +761,6 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
};
&watchdog0 {