Update MTD to that of Linux 2.6.22.1
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
diff --git a/board/prodrive/alpr/nand.c b/board/prodrive/alpr/nand.c
index 097e183..3224d3d 100644
--- a/board/prodrive/alpr/nand.c
+++ b/board/prodrive/alpr/nand.c
@@ -56,43 +56,24 @@
*
* There are 2 NAND devices on the board, a Hynix HY27US08561A (1 GByte).
*/
-static void alpr_nand_hwcontrol(struct mtd_info *mtd, int cmd)
-{
- switch (cmd) {
- case NAND_CTL_SETCLE:
- hwctl |= 0x1;
- break;
- case NAND_CTL_CLRCLE:
- hwctl &= ~0x1;
- break;
- case NAND_CTL_SETALE:
- hwctl |= 0x2;
- break;
- case NAND_CTL_CLRALE:
- hwctl &= ~0x2;
- break;
- case NAND_CTL_SETNCE:
- break;
- case NAND_CTL_CLRNCE:
- writeb(0x00, &(alpr_ndfc->term));
- break;
+static void alpr_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ if ( ctrl & NAND_CLE )
+ hwctl |= 0x1;
+ else
+ hwctl &= ~0x1;
+ if ( ctrl & NAND_ALE )
+ hwctl |= 0x2;
+ else
+ hwctl &= ~0x2;
+ if ( (ctrl & NAND_NCE) != NAND_NCE)
+ writeb(0x00, &(alpr_ndfc->term));
}
-}
-
-static void alpr_nand_write_byte(struct mtd_info *mtd, u_char byte)
-{
- struct nand_chip *nand = mtd->priv;
-
- if (hwctl & 0x1)
- /*
- * IO_ADDR_W used as CMD[i] reg to support multiple NAND
- * chips.
- */
- writeb(byte, nand->IO_ADDR_W);
- else if (hwctl & 0x2) {
- writeb(byte, &(alpr_ndfc->addr_wait));
- } else
- writeb(byte, &(alpr_ndfc->data));
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, this->IO_ADDR_W);
}
static u_char alpr_nand_read_byte(struct mtd_info *mtd)
@@ -158,12 +139,10 @@
{
alpr_ndfc = (struct alpr_ndfc_regs *)CFG_NAND_BASE;
- nand->eccmode = NAND_ECC_SOFT;
+ nand->ecc.mode = NAND_ECC_SOFT;
/* Reference hardware control function */
- nand->hwcontrol = alpr_nand_hwcontrol;
- /* Set command delay time */
- nand->write_byte = alpr_nand_write_byte;
+ nand->cmd_ctrl = alpr_nand_hwcontrol;
nand->read_byte = alpr_nand_read_byte;
nand->write_buf = alpr_nand_write_buf;
nand->read_buf = alpr_nand_read_buf;