imx6dl/imx6qdl: synchronise device trees with linux
Synchronise device trees with linux-next next-20220708.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
diff --git a/arch/arm/dts/imx6q-mccmon6.dts b/arch/arm/dts/imx6q-mccmon6.dts
index 27cde56..55692c7 100644
--- a/arch/arm/dts/imx6q-mccmon6.dts
+++ b/arch/arm/dts/imx6q-mccmon6.dts
@@ -1,39 +1,89 @@
-// SPDX-License-Identifier: GPL-2.0+
+// SPDX-License-Identifier: GPL-2.0-only
/*
- * Copyright 2019
+ * Copyright 2016-2017
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+ or X11
*/
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
+
#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
/ {
- model = "Liebherr Nenzig (LWN) iMX6Q";
- compatible = "lwn,imx6-mccmon6", "fsl,imx6";
-
- aliases {
- mmc0 = &usdhc3;
- mmc1 = &usdhc2;
- spi0 = &ecspi3;
- };
-
- chosen {
- stdout-path = &uart1;
- };
+ model = "Liebherr (LWN) monitor6 i.MX6 Quad Board";
+ compatible = "lwn,mccmon6", "fsl,imx6q";
memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x80000000>;
};
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100 101 102 103 104 105 106 107 108 109
+ 110 111 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127 128 129
+ 130 131 132 133 134 135 136 137 138 139
+ 140 141 142 143 144 145 146 147 148 149
+ 150 151 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167 168 169
+ 170 171 172 173 174 175 176 177 178 179
+ 180 181 182 183 184 185 186 187 188 189
+ 190 191 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207 208 209
+ 210 211 212 213 214 215 216 217 218 219
+ 220 221 222 223 224 225 226 227 228 229
+ 230 231 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247 248 249
+ 250 251 252 253 254 255>;
+ default-brightness-level = <50>;
+ enable-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ };
+
+ reg_lvds: regulator-lvds {
+ compatible = "regulator-fixed";
+ regulator-name = "lvds_ppen";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_lvds>;
+ gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ panel-lvds0 {
+ compatible = "innolux,g121x1-l03";
+ backlight = <&backlight_lvds>;
+ power-supply = <®_lvds>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
};
&ecspi3 {
cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
- spi-max-frequency = <25000000>;
status = "okay";
s25sl032p: flash@0 {
@@ -50,21 +100,8 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <1>;
- /* KSZ9031 PHY SKEW setup - old values * 60 ps */
- rxc-skew-ps = <1860>;
- txc-skew-ps = <1860>;
- txen-skew-ps = <900>;
- rxdv-skew-ps = <900>;
- rxd0-skew-ps = <180>;
- rxd1-skew-ps = <180>;
- rxd2-skew-ps = <180>;
- rxd3-skew-ps = <180>;
- txd0-skew-ps = <120>;
- txd1-skew-ps = <300>;
- txd2-skew-ps = <0>;
- txd3-skew-ps = <120>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
status = "okay";
};
@@ -181,6 +218,59 @@
};
};
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&weim {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
@@ -201,7 +291,13 @@
&iomuxc {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_backlight: dispgrp {
+ fsl,pins = <
+ /* BLEN_OUT */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
pinctrl_ecspi3: ecspi3grp {
fsl,pins = <
@@ -246,13 +342,6 @@
>;
};
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
- >;
- };
-
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
@@ -267,6 +356,19 @@
>;
};
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_lvds: reqlvdsgrp {
+ fsl,pins = <
+ /* LVDS_PPEN_OUT */
+ MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
@@ -274,6 +376,15 @@
>;
};
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
@@ -356,27 +467,3 @@
>;
};
};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- bus-width = <4>;
- cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- non-removable;
- no-1-8-v;
- keep-power-in-suspend;
- status = "okay";
-};