ppc4xx: Big cleanup of PPC4xx defines
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/esd/pci405/pci405.c b/board/esd/pci405/pci405.c
index 56184ca..04bc569 100644
--- a/board/esd/pci405/pci405.c
+++ b/board/esd/pci405/pci405.c
@@ -67,7 +67,7 @@
int board_revision(void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
@@ -77,8 +77,8 @@
/*
* Setup GPIO pins (CS2/GPIO11 and CS3/GPIO12 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x03000000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03000000);
out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00100200);
out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00100200);
udelay(1000); /* wait some time before reading input */
@@ -87,7 +87,7 @@
/*
* Restore GPIO settings
*/
- mtdcr(cntrl0, cntrl0Reg);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg);
switch (value) {
case 0x00100200:
@@ -133,7 +133,7 @@
int board_early_init_f (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
/*
* First pull fpga-prg pin low, to disable fpga logic (on version 1.2 board)
@@ -166,18 +166,18 @@
/*
* Setup GPIO pins (IRQ4/GPIO21 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00008000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00008000);
/*
* Setup GPIO pins (CS6+CS7 as GPIO)
*/
- mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 25 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
@@ -282,11 +282,11 @@
#define PCI0_BRDGOPT1 0x4a
pci_write_config_word(PCIDEVID_405GP, PCI0_BRDGOPT1, 0x3f20);
-#define plb0_acr 0x87
+#define PLB0_ACR 0x87
/*
* Enable fairness and high bus utilization
*/
- mtdcr(plb0_acr, 0x98000000);
+ mtdcr(PLB0_ACR, 0x98000000);
free(dst);
return (0);
@@ -313,14 +313,14 @@
printf(" (Rev 1.%ld", gd->board_type);
if (gd->board_type >= 2) {
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
* Setup GPIO pins (Trace/GPIO1 to GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg & ~0x08000000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg & ~0x08000000);
out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x40000000);
out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x40000000);
udelay(1000); /* wait some time before reading input */