imx: add i.MX8MN DDR4 board support

Support pinctrl/clk/sdhc, include ddr4 timing data.

Log:
U-Boot SPL 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)
Normal Boot
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0

U-Boot 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)

CPU:   Freescale i.MX8MNano rev1.0 at 24 MHz
Reset cause: POR
Model: NXP i.MX8MNano DDR4 EVK board
DRAM:  2 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 251d32c..3e2677c 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -660,6 +660,7 @@
 
 dtb-$(CONFIG_ARCH_IMX8M) += \
 	imx8mm-evk.dtb \
+	imx8mn-ddr4-evk.dtb \
 	imx8mq-evk.dtb
 
 dtb-$(CONFIG_RCAR_GEN2) += \
diff --git a/arch/arm/dts/imx8mm-evk.dts b/arch/arm/dts/imx8mm-evk.dts
index faefb71..ef249ff 100644
--- a/arch/arm/dts/imx8mm-evk.dts
+++ b/arch/arm/dts/imx8mm-evk.dts
@@ -464,7 +464,7 @@
 			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d0
 			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d0
 			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d0
-			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 		0x190
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x190
 		>;
 	};
 
@@ -480,7 +480,7 @@
 			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
 			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
 			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
-			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 		0x194
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x194
 		>;
 	};
 
@@ -496,7 +496,7 @@
 			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d6
 			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d6
 			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d6
-			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 		0x196
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x196
 		>;
 	};
 
diff --git a/arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi b/arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi
new file mode 100644
index 0000000..8d61597
--- /dev/null
+++ b/arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+&{/soc@0} {
+	u-boot,dm-pre-reloc;
+	u-boot,dm-spl;
+};
+
+&clk {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&osc_24m {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&aips1 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+	u-boot,dm-spl;
+};
+
+&aips3 {
+	u-boot,dm-spl;
+};
+
+&iomuxc {
+	u-boot,dm-spl;
+};
+
+&pinctrl_reg_usdhc2_vmmc {
+	u-boot,dm-spl;
+};
+
+&pinctrl_uart2 {
+	u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2_gpio {
+	u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2 {
+	u-boot,dm-spl;
+};
+
+&pinctrl_usdhc3 {
+	u-boot,dm-spl;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+};
+
+&gpio2 {
+	u-boot,dm-spl;
+};
+
+&gpio3 {
+	u-boot,dm-spl;
+};
+
+&gpio4 {
+	u-boot,dm-spl;
+};
+
+&gpio5 {
+	u-boot,dm-spl;
+};
+
+&uart2 {
+	u-boot,dm-spl;
+};
+
+&usdhc1 {
+	u-boot,dm-spl;
+};
+
+&usdhc2 {
+	u-boot,dm-spl;
+};
+
+&usdhc3 {
+	u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/imx8mn-ddr4-evk.dts b/arch/arm/dts/imx8mn-ddr4-evk.dts
new file mode 100644
index 0000000..9b2c172
--- /dev/null
+++ b/arch/arm/dts/imx8mn-ddr4-evk.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8mn.dtsi"
+
+/ {
+	model = "NXP i.MX8MNano DDR4 EVK board";
+	compatible = "fsl,imx8mn-ddr4-evk", "fsl,imx8mn";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_ENET_MDC_ENET1_MDC		0x3
+			MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO	0x3
+			MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x1f
+			MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x1f
+			MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x1f
+			MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x1f
+			MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x91
+			MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x91
+			MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x91
+			MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x91
+			MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
+			MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
+			MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22	0x19
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX	0x140
+			MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x1c4
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x190
+			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0
+			MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d0
+			MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d0
+			MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d0
+			MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d0
+			MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+			MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+			MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x40000190
+			MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d0
+			MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d0
+			MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d0
+			MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d0
+			MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d0
+			MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d0
+			MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d0
+			MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d0
+			MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d0
+			MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x40000194
+			MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
+			MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x40000196
+			MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
+			MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d6
+			MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d6
+			MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d6
+			MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d6
+			MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d6
+			MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d6
+			MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d6
+			MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d6
+			MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			at803x,led-act-blind-workaround;
+			at803x,eee-disabled;
+			at803x,vddio-1p8v;
+		};
+	};
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart2 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};