punt Blackfin VDSP headers and import sanitized/auto-generated ones
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/board/bf533-ezkit/flash.c b/board/bf533-ezkit/flash.c
index 299cdba..cdf4dc6 100644
--- a/board/bf533-ezkit/flash.c
+++ b/board/bf533-ezkit/flash.c
@@ -286,9 +286,9 @@
long addr;
addr = (CFG_FLASH_BASE + nOffset);
- sync();
+ SSYNC();
*(unsigned volatile short *)addr = nValue;
- sync();
+ SSYNC();
if (poll_toggle_bit(nOffset) < 0)
return FLASH_FAIL;
return FLASH_SUCCESS;
@@ -301,9 +301,9 @@
if (nOffset != 0x2)
reset_flash();
- sync();
+ SSYNC();
nValue = *(volatile unsigned short *)addr;
- sync();
+ SSYNC();
*pnValue = nValue;
return TRUE;
}
diff --git a/board/bf533-stamp/bf533-stamp.c b/board/bf533-stamp/bf533-stamp.c
index 69e425b..af03597 100644
--- a/board/bf533-stamp/bf533-stamp.c
+++ b/board/bf533-stamp/bf533-stamp.c
@@ -76,9 +76,9 @@
if (device_id == ETHERNET) {
*pFIO_DIR = PF0;
- sync();
+ SSYNC();
*pFIO_FLAG_S = PF0;
- sync();
+ SSYNC();
} else if (device_id == FLASH) {
*pFIO_DIR = (PF4 | PF3 | PF2 | PF1 | PF0);
*pFIO_FLAG_S = (PF4 | PF3 | PF2);
@@ -88,7 +88,7 @@
*pFIO_EDGE = (PF8 | PF7 | PF6 | PF5);
*pFIO_INEN = (PF8 | PF7 | PF6 | PF5);
*pFIO_FLAG_D = (PF4 | PF3 | PF2);
- sync();
+ SSYNC();
} else {
printf("Unknown bank to switch\n");
}
@@ -155,15 +155,15 @@
*/
*pFIO_FLAG_S = CF_PF0;
*pFIO_FLAG_C = CF_PF1;
- sync();
+ SSYNC();
*(addr) = val;
- sync();
+ SSYNC();
/* Setback PF1 PF0 to 0 0 to address external
* memory banks */
*(volatile unsigned short *)pFIO_FLAG_C = CF_PF1_PF0;
- sync();
+ SSYNC();
}
unsigned char cf_inb(volatile unsigned char *addr)
@@ -172,13 +172,13 @@
*pFIO_FLAG_S = CF_PF0;
*pFIO_FLAG_C = CF_PF1;
- sync();
+ SSYNC();
c = *(addr);
- sync();
+ SSYNC();
*pFIO_FLAG_C = CF_PF1_PF0;
- sync();
+ SSYNC();
return c;
}
@@ -189,15 +189,15 @@
*pFIO_FLAG_S = CF_PF0;
*pFIO_FLAG_C = CF_PF1;
- sync();
+ SSYNC();
for (i = 0; i < words; i++) {
*(sect_buf + i) = *(addr);
- sync();
+ SSYNC();
}
*pFIO_FLAG_C = CF_PF1_PF0;
- sync();
+ SSYNC();
}
void cf_outsw(unsigned short *addr, unsigned short *sect_buf, int words)
@@ -206,15 +206,15 @@
*pFIO_FLAG_S = CF_PF0;
*pFIO_FLAG_C = CF_PF1;
- sync();
+ SSYNC();
for (i = 0; i < words; i++) {
*(addr) = *(sect_buf + i);
- sync();
+ SSYNC();
}
*pFIO_FLAG_C = CF_PF1_PF0;
- sync();
+ SSYNC();
}
#endif
@@ -235,7 +235,7 @@
*pFIO_FLAG_S = PF4;
else
*pFIO_FLAG_C = PF4;
- sync();
+ SSYNC();
}
void show_boot_progress(int status)
diff --git a/board/bf533-stamp/spi.c b/board/bf533-stamp/spi.c
index d30750f..15141cf 100644
--- a/board/bf533-stamp/spi.c
+++ b/board/bf533-stamp/spi.c
@@ -4,6 +4,7 @@
#include <common.h>
#include <linux/ctype.h>
#include <asm/io.h>
+#include <asm/mach-common/bits/spi.h>
#if defined(CONFIG_SPI)
@@ -153,7 +154,7 @@
/*sends the actual command to the SPI TX register */
*pSPI_TDBR = iCommand;
- sync();
+ SSYNC();
/*The SPI status register will be polled to check the SPIF bit */
Wait_For_SPIF();
@@ -174,7 +175,7 @@
*pSPI_FLG = 0xFB04;
*pSPI_BAUD = CONFIG_SPI_BAUD;
*pSPI_CTL = spi_setting;
- sync();
+ SSYNC();
}
void SPI_OFF(void)
@@ -183,7 +184,7 @@
*pSPI_CTL = 0x0400; /* disable SPI */
*pSPI_FLG = 0;
*pSPI_BAUD = 0;
- sync();
+ SSYNC();
udelay(CONFIG_CCLK_HZ / 50000000);
}
@@ -241,10 +242,10 @@
SetupSPI((COMMON_SPI_SETTINGS | TIMOD01)); /* Turn on the SPI */
*pSPI_TDBR = SPI_RDSR; /* send instruction to read status register */
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the instruction has been sent */
*pSPI_TDBR = 0; /*send dummy to receive the status register */
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the data has been sent */
status_register = *pSPI_RDBR; /*read the status register */
@@ -305,18 +306,18 @@
/* Send the erase block command to the flash followed by the 24 address */
/* to point to the start of a sector. */
*pSPI_TDBR = SPI_SE;
- sync();
+ SSYNC();
Wait_For_SPIF();
ShiftValue = (ulSectorOff >> 16); /* Send the highest byte of the 24 bit address at first */
*pSPI_TDBR = ShiftValue;
- sync();
+ SSYNC();
Wait_For_SPIF(); /* Wait until the instruction has been sent */
ShiftValue = (ulSectorOff >> 8); /* Send the middle byte of the 24 bit address at second */
*pSPI_TDBR = ShiftValue;
- sync();
+ SSYNC();
Wait_For_SPIF(); /* Wait until the instruction has been sent */
*pSPI_TDBR = ulSectorOff; /* Send the lowest byte of the 24 bit address finally */
- sync();
+ SSYNC();
Wait_For_SPIF(); /* Wait until the instruction has been sent */
/*Turns off the SPI */
@@ -351,25 +352,25 @@
SetupSPI((COMMON_SPI_SETTINGS | TIMOD01));
*pSPI_TDBR = SPI_READ; /* Send the read command to SPI device */
- sync();
+ SSYNC();
Wait_For_SPIF(); /* Wait until the instruction has been sent */
ShiftValue = (ulStart >> 16); /* Send the highest byte of the 24 bit address at first */
*pSPI_TDBR = ShiftValue; /* Send the byte to the SPI device */
- sync();
+ SSYNC();
Wait_For_SPIF(); /* Wait until the instruction has been sent */
ShiftValue = (ulStart >> 8); /* Send the middle byte of the 24 bit address at second */
*pSPI_TDBR = ShiftValue; /* Send the byte to the SPI device */
- sync();
+ SSYNC();
Wait_For_SPIF(); /* Wait until the instruction has been sent */
*pSPI_TDBR = ulStart; /* Send the lowest byte of the 24 bit address finally */
- sync();
+ SSYNC();
Wait_For_SPIF(); /* Wait until the instruction has been sent */
/* After the SPI device address has been placed on the MOSI pin the data can be */
/* received on the MISO pin. */
for (i = 0; i < lCount; i++) {
*pSPI_TDBR = 0; /*send dummy */
- sync();
+ SSYNC();
while (!(*pSPI_STAT & RXS)) ;
*cnData++ = *pSPI_RDBR; /*read */
@@ -406,26 +407,26 @@
/* Third, the 24 bit address will be shifted out the SPI MOSI bytewise. */
SetupSPI((COMMON_SPI_SETTINGS | TIMOD01)); /* Turns the SPI on */
*pSPI_TDBR = SPI_PP;
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the instruction has been sent */
ulWAddr = (ulStartAddr >> 16);
*pSPI_TDBR = ulWAddr;
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the instruction has been sent */
ulWAddr = (ulStartAddr >> 8);
*pSPI_TDBR = ulWAddr;
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the instruction has been sent */
ulWAddr = ulStartAddr;
*pSPI_TDBR = ulWAddr;
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the instruction has been sent */
/* Fourth, maximum number of 256 bytes will be taken from the Buffer */
/* and sent to the SPI device. */
for (i = 0; (i < lTransferCount) && (i < 256); i++, lWTransferCount++) {
iData = *temp;
*pSPI_TDBR = iData;
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the instruction has been sent */
temp++;
}
diff --git a/board/bf537-stamp/bf537-stamp.c b/board/bf537-stamp/bf537-stamp.c
index 6954b30..d279817 100644
--- a/board/bf537-stamp/bf537-stamp.c
+++ b/board/bf537-stamp/bf537-stamp.c
@@ -32,6 +32,7 @@
#include <asm/io.h>
#include <net.h>
#include "ether_bf537.h"
+#include <asm/mach-common/bits/bootrom.h>
/**
* is_valid_ether_addr - Determine if the given Ethernet address is valid
@@ -117,7 +118,7 @@
void cf_outb(unsigned char val, volatile unsigned char *addr)
{
*(addr) = val;
- sync();
+ SSYNC();
}
unsigned char cf_inb(volatile unsigned char *addr)
@@ -125,7 +126,7 @@
volatile unsigned char c;
c = *(addr);
- sync();
+ SSYNC();
return c;
}
@@ -136,7 +137,7 @@
for (i = 0; i < words; i++)
*(sect_buf + i) = *(addr);
- sync();
+ SSYNC();
}
void cf_outsw(unsigned short *addr, unsigned short *sect_buf, int words)
@@ -145,7 +146,7 @@
for (i = 0; i < words; i++)
*(addr) = *(sect_buf + i);
- sync();
+ SSYNC();
}
#endif /* CONFIG_BFIN_IDE */
diff --git a/board/bf537-stamp/ether_bf537.c b/board/bf537-stamp/ether_bf537.c
index 36c1536..6c514c6 100644
--- a/board/bf537-stamp/ether_bf537.c
+++ b/board/bf537-stamp/ether_bf537.c
@@ -30,6 +30,10 @@
#include <malloc.h>
#include "ether_bf537.h"
+#include <asm/mach-common/bits/dma.h>
+#include <asm/mach-common/bits/emac.h>
+#include <asm/mach-common/bits/pll.h>
+
#ifdef CONFIG_POST
#include <post.h>
#endif
@@ -364,7 +368,7 @@
u16 sysctl, phydat;
int count = 0;
/* Enable PHY output */
- *pVR_CTL |= PHYCLKOE;
+ *pVR_CTL |= CLKBUFOE;
/* MDC = 2.5 MHz */
sysctl = SET_MDCDIV(24);
/* Odd word alignment for Receive Frame DMA word */
diff --git a/board/bf537-stamp/flash.c b/board/bf537-stamp/flash.c
index ed85841..8252c42 100644
--- a/board/bf537-stamp/flash.c
+++ b/board/bf537-stamp/flash.c
@@ -255,7 +255,7 @@
addr = (CFG_FLASH_BASE + nOffset);
*(unsigned volatile short *)addr = nValue;
- sync();
+ SSYNC();
#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
if (icache_status())
udelay(CONFIG_CCLK_HZ / 1000000);
diff --git a/board/bf537-stamp/nand.c b/board/bf537-stamp/nand.c
index f95b584..6ff0f4f 100644
--- a/board/bf537-stamp/nand.c
+++ b/board/bf537-stamp/nand.c
@@ -64,13 +64,13 @@
this->IO_ADDR_R = this->IO_ADDR_W;
/* Drain the writebuffer */
- sync();
+ SSYNC();
}
int bfin_device_ready(struct mtd_info *mtd)
{
int ret = (*PORT(CONFIG_NAND_GPIO_PORT, IO) & BFIN_NAND_READY) ? 1 : 0;
- sync();
+ SSYNC();
return ret;
}
diff --git a/board/bf537-stamp/post-memory.c b/board/bf537-stamp/post-memory.c
index 6039350..fa11991 100644
--- a/board/bf537-stamp/post-memory.c
+++ b/board/bf537-stamp/post-memory.c
@@ -104,15 +104,15 @@
*pUART_GCTL = 0x00;
*pUART_LCR = 0x83;
- sync();
+ SSYNC();
*pUART_DLL = (divisor & 0xFF);
- sync();
+ SSYNC();
*pUART_DLH = ((divisor >> 8) & 0xFF);
- sync();
+ SSYNC();
*pUART_LCR = 0x03;
- sync();
+ SSYNC();
*pUART_GCTL = 0x01;
- sync();
+ SSYNC();
}
void post_out_buff(char *buff)
@@ -124,7 +124,7 @@
while ((buff[i] != '\0') && (i != 100)) {
while (!(*pUART_LSR & 0x20)) ;
*pUART_THR = buff[i];
- sync();
+ SSYNC();
i++;
}
for (i = 0; i < 0x80000; i++) ;
@@ -141,7 +141,7 @@
*pPORTF_FER &= ~PF5;
*pPORTFIO_DIR &= ~PF5;
*pPORTFIO_INEN |= PF5;
- sync();
+ SSYNC();
post_out_buff("########Press SW10 to enter Memory POST########: 3\0");
for (i = 0; i < KEY_LOOP; i++) {
@@ -303,7 +303,7 @@
(SCTLE | SDRAM_CL | SDRAM_tRAS | SDRAM_tRP | SDRAM_tRCD | SDRAM_tWR
| PSS);
- sync();
+ SSYNC();
*pEBIU_SDGCTL |= 0x1000000;
/* Set the SDRAM Refresh Rate control register based on SSCLK value */
@@ -314,7 +314,7 @@
/* SDRAM Memory Global Control Register */
*pEBIU_SDGCTL = mem_SDGCTL;
- sync();
+ SSYNC();
return mem_SDRRC;
}
diff --git a/board/bf537-stamp/stm_m25p64.c b/board/bf537-stamp/stm_m25p64.c
index d9c08ee..c48c3c7 100644
--- a/board/bf537-stamp/stm_m25p64.c
+++ b/board/bf537-stamp/stm_m25p64.c
@@ -4,6 +4,7 @@
#include <common.h>
#include <linux/ctype.h>
#include <asm/io.h>
+#include <asm/mach-common/bits/spi.h>
#if defined(CONFIG_SPI)
@@ -142,7 +143,7 @@
/* sends the actual command to the SPI TX register */
*pSPI_TDBR = iCommand;
- sync();
+ SSYNC();
/* The SPI status register will be polled to check the SPIF bit */
Wait_For_SPIF();
@@ -164,10 +165,10 @@
*pSPI_FLG = 0xFF02;
*pSPI_BAUD = CONFIG_SPI_BAUD;
*pSPI_CTL = spi_setting;
- sync();
+ SSYNC();
*pSPI_FLG = 0xFD02;
- sync();
+ SSYNC();
}
void SPI_OFF(void)
@@ -176,7 +177,7 @@
*pSPI_CTL = 0x0400; /* disable SPI */
*pSPI_FLG = 0;
*pSPI_BAUD = 0;
- sync();
+ SSYNC();
udelay(CONFIG_CCLK_HZ / 50000000);
}
@@ -234,10 +235,10 @@
SetupSPI((COMMON_SPI_SETTINGS | TIMOD01)); /* Turn on the SPI */
*pSPI_TDBR = SPI_RDSR; /* send instruction to read status register */
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the instruction has been sent */
*pSPI_TDBR = 0; /*send dummy to receive the status register */
- sync();
+ SSYNC();
Wait_For_SPIF(); /*wait until the data has been sent */
status_register = *pSPI_RDBR; /*read the status register */
@@ -300,23 +301,23 @@
* to point to the start of a sector
*/
*pSPI_TDBR = SPI_SE;
- sync();
+ SSYNC();
Wait_For_SPIF();
/* Send the highest byte of the 24 bit address at first */
ShiftValue = (ulSectorOff >> 16);
*pSPI_TDBR = ShiftValue;
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
/* Send the middle byte of the 24 bit address at second */
ShiftValue = (ulSectorOff >> 8);
*pSPI_TDBR = ShiftValue;
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
/* Send the lowest byte of the 24 bit address finally */
*pSPI_TDBR = ulSectorOff;
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
@@ -357,33 +358,33 @@
/* Send the read command to SPI device */
*pSPI_TDBR = SPI_READ;
#endif
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
/* Send the highest byte of the 24 bit address at first */
ShiftValue = (ulStart >> 16);
/* Send the byte to the SPI device */
*pSPI_TDBR = ShiftValue;
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
/* Send the middle byte of the 24 bit address at second */
ShiftValue = (ulStart >> 8);
/* Send the byte to the SPI device */
*pSPI_TDBR = ShiftValue;
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
/* Send the lowest byte of the 24 bit address finally */
*pSPI_TDBR = ulStart;
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
#ifdef CONFIG_SPI_FLASH_FAST_READ
/* Send dummy for FAST_READ */
*pSPI_TDBR = 0;
- sync();
+ SSYNC();
/* Wait until the instruction has been sent */
Wait_For_SPIF();
#endif
@@ -392,7 +393,7 @@
/* received on the MISO pin. */
for (i = 0; i < lCount; i++) {
*pSPI_TDBR = 0;
- sync();
+ SSYNC();
while (!(*pSPI_STAT & RXS)) ;
*cnData++ = *pSPI_RDBR;
@@ -435,22 +436,22 @@
*/
SetupSPI((COMMON_SPI_SETTINGS | TIMOD01));
*pSPI_TDBR = SPI_PP;
- sync();
+ SSYNC();
/*wait until the instruction has been sent */
Wait_For_SPIF();
ulWAddr = (ulStartAddr >> 16);
*pSPI_TDBR = ulWAddr;
- sync();
+ SSYNC();
/*wait until the instruction has been sent */
Wait_For_SPIF();
ulWAddr = (ulStartAddr >> 8);
*pSPI_TDBR = ulWAddr;
- sync();
+ SSYNC();
/*wait until the instruction has been sent */
Wait_For_SPIF();
ulWAddr = ulStartAddr;
*pSPI_TDBR = ulWAddr;
- sync();
+ SSYNC();
/*wait until the instruction has been sent */
Wait_For_SPIF();
/*
@@ -460,7 +461,7 @@
for (i = 0; (i < lTransferCount) && (i < 256); i++, lWTransferCount++) {
iData = *temp;
*pSPI_TDBR = iData;
- sync();
+ SSYNC();
/*wait until the instruction has been sent */
Wait_For_SPIF();
temp++;
diff --git a/board/bf561-ezkit/bf561-ezkit.c b/board/bf561-ezkit/bf561-ezkit.c
index 2ff44a7..d504217 100644
--- a/board/bf561-ezkit/bf561-ezkit.c
+++ b/board/bf561-ezkit/bf561-ezkit.c
@@ -65,9 +65,9 @@
/* Keep PF12 low to be able to drive the USB-LAN Extender */
*pFIO0_DIR = 0x0000;
*pFIO0_FLAG_C = 0x1000; /* Clear PF12 */
- sync();
+ SSYNC();
*pFIO0_POLAR = 0x0000;
- sync();
+ SSYNC();
return 0;
}