FRAM memory access optimization.
diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c
index 80b8ccc..2d4c9f6 100644
--- a/common/cmd_eeprom.c
+++ b/common/cmd_eeprom.c
@@ -22,6 +22,21 @@
*
*/
+/*
+ * Support for read and write access to EEPROM like memory devices. This
+ * includes regular EEPROM as well as FRAM (ferroelectic nonvolaile RAM).
+ * FRAM devices read and write data at bus speed. In particular, there is no
+ * write delay. Also, there is no limit imposed on the numer of bytes that can
+ * be transferred with a single read or write.
+ *
+ * Use the following configuration options to ensure no unneeded performance
+ * degradation (typical for EEPROM) is incured for FRAM memory:
+ *
+ * #define CFG_I2C_FRAM
+ * #undef CFG_EEPROM_PAGE_WRITE_DELAY_MS
+ *
+ */
+
#include <common.h>
#include <config.h>
#include <command.h>
@@ -122,7 +137,11 @@
* because the next page may be in a different device.
*/
while (offset < end) {
- unsigned alen, len, maxlen;
+ unsigned alen, len;
+#if !defined(CFG_I2C_FRAM)
+ unsigned maxlen;
+#endif
+
#if CFG_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
uchar addr[2];
@@ -144,12 +163,21 @@
addr[0] |= dev_addr; /* insert device address */
+ len = end - offset;
+
+ /*
+ * For a FRAM device there is no limit on the number of the
+ * bytes that can be ccessed with the single read or write
+ * operation.
+ */
+#if !defined(CFG_I2C_FRAM)
maxlen = 0x100 - blk_off;
if (maxlen > I2C_RXTX_LEN)
maxlen = I2C_RXTX_LEN;
- len = end - offset;
if (len > maxlen)
len = maxlen;
+#endif
+
#ifdef CONFIG_SPI
spi_read (addr, alen, buffer, len);
#else
@@ -159,6 +187,7 @@
buffer += len;
offset += len;
}
+
return rcode;
}
@@ -191,7 +220,11 @@
*/
while (offset < end) {
- unsigned alen, len, maxlen;
+ unsigned alen, len;
+#if !defined(CFG_I2C_FRAM)
+ unsigned maxlen;
+#endif
+
#if CFG_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
uchar addr[2];
@@ -213,6 +246,15 @@
addr[0] |= dev_addr; /* insert device address */
+ len = end - offset;
+
+ /*
+ * For a FRAM device there is no limit on the number of the
+ * bytes that can be ccessed with the single read or write
+ * operation.
+ */
+#if !defined(CFG_I2C_FRAM)
+
#if defined(CFG_EEPROM_PAGE_WRITE_BITS)
#define EEPROM_PAGE_SIZE (1 << CFG_EEPROM_PAGE_WRITE_BITS)
@@ -225,9 +267,10 @@
if (maxlen > I2C_RXTX_LEN)
maxlen = I2C_RXTX_LEN;
- len = end - offset;
if (len > maxlen)
len = maxlen;
+#endif
+
#ifdef CONFIG_SPI
spi_write (addr, alen, buffer, len);
#else
diff --git a/common/cmd_i2c.c b/common/cmd_i2c.c
index 9c02ceb..2e44c7f 100644
--- a/common/cmd_i2c.c
+++ b/common/cmd_i2c.c
@@ -295,7 +295,13 @@
* chip doesn't respond. This apparently isn't a
* universal feature so we don't take advantage of it.
*/
+/*
+ * No write delay with FRAM devices.
+ */
+#if !defined(CFG_I2C_FRAM)
udelay(11000);
+#endif
+
#if 0
for(timeout = 0; timeout < 10; timeout++) {
udelay(2000);