OMAP3: Zoom1: Use generic MMC driver
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
diff --git a/board/logicpd/zoom1/zoom1.c b/board/logicpd/zoom1/zoom1.c
index 7ef13cc..dec0b26 100644
--- a/board/logicpd/zoom1/zoom1.c
+++ b/board/logicpd/zoom1/zoom1.c
@@ -34,6 +34,7 @@
#include <netdev.h>
#include <twl4030.h>
#include <asm/io.h>
+#include <asm/arch/mmc_host_def.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-types.h>
@@ -88,6 +89,14 @@
MUX_ZOOM1_MDK();
}
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+ omap_mmc_init(0);
+ return 0;
+}
+#endif
+
#ifdef CONFIG_CMD_NET
int board_eth_init(bd_t *bis)
{
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index f106b38..fbac222 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -95,8 +95,9 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
/* DDR - I use Micron DDR */
@@ -178,6 +179,7 @@
"loadaddr=0x82000000\0" \
"usbtty=cdc_acm\0" \
"console=ttyS2,115200n8\0" \
+ "mmcdev=0\0" \
"videomode=1024x768@60,vxres=1024,vyres=768\0" \
"videospec=omapfb:vram:2M,vram:4M\0" \
"mmcargs=setenv bootargs console=${console} " \
@@ -188,10 +190,10 @@
"video=${videospec},mode:${videomode} " \
"root=/dev/mtdblock4 rw " \
"rootfstype=jffs2\0" \
- "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
- "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
@@ -201,7 +203,7 @@
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmc init; then " \
+ "if mmc rescan ${mmcdev}; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \