i2c: Drop CONFIG_TSI108_I2C
Last user of this driver went away in June 2015 in commit
d928664f4101e24 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
diff --git a/doc/driver-model/i2c-howto.txt b/doc/driver-model/i2c-howto.txt
index 605d3ef..1b2c531 100644
--- a/doc/driver-model/i2c-howto.txt
+++ b/doc/driver-model/i2c-howto.txt
@@ -16,7 +16,6 @@
sh_i2c
sh_sh7734_i2c
soft_i2c
- tsi108_i2c
zynq_i2c
The deadline for this work is the end of June 2017. If no one steps
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 8bb3c18..4cf5c51 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -9,7 +9,6 @@
obj-$(CONFIG_$(SPL_)I2C_CROS_EC_LDO) += cros_ec_ldo.o
obj-$(CONFIG_I2C_MV) += mv_i2c.o
-obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
obj-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
obj-$(CONFIG_SYS_I2C) += i2c_core.o
obj-$(CONFIG_SYS_I2C_ASPEED) += ast_i2c.o
diff --git a/drivers/i2c/tsi108_i2c.c b/drivers/i2c/tsi108_i2c.c
deleted file mode 100644
index 208c090..0000000
--- a/drivers/i2c/tsi108_i2c.c
+++ /dev/null
@@ -1,275 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2004 Tundra Semiconductor Corp.
- * Author: Alex Bounine
- *
- * NOTE: This driver should be converted to driver model before June 2017.
- * Please see doc/driver-model/i2c-howto.txt for instructions.
- */
-
-#include <config.h>
-#include <common.h>
-
-#include <tsi108.h>
-
-#if defined(CONFIG_CMD_I2C)
-
-#define I2C_DELAY 100000
-#undef DEBUG_I2C
-
-#ifdef DEBUG_I2C
-#define DPRINT(x) printf (x)
-#else
-#define DPRINT(x)
-#endif
-
-/* All functions assume that Tsi108 I2C block is the only master on the bus */
-/* I2C read helper function */
-
-void i2c_init(int speed, int slaveaddr)
-{
- /*
- * The TSI108 has a fixed I2C clock rate and doesn't support slave
- * operation. This function only exists as a stub to fit into the
- * U-Boot I2C API.
- */
-}
-
-static int i2c_read_byte (
- uint i2c_chan, /* I2C channel number: 0 - main, 1 - SDC SPD */
- uchar chip_addr,/* I2C device address on the bus */
- uint byte_addr, /* Byte address within I2C device */
- uchar * buffer /* pointer to data buffer */
- )
-{
- u32 temp;
- u32 to_count = I2C_DELAY;
- u32 op_status = TSI108_I2C_TIMEOUT_ERR;
- u32 chan_offset = TSI108_I2C_OFFSET;
-
- DPRINT (("I2C read_byte() %d 0x%02x 0x%02x\n",
- i2c_chan, chip_addr, byte_addr));
-
- if (0 != i2c_chan)
- chan_offset = TSI108_I2C_SDRAM_OFFSET;
-
- /* Check if I2C operation is in progress */
- temp = *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2);
-
- if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS |
- I2C_CNTRL2_START))) {
- /* Set device address and operation (read = 0) */
- temp = (byte_addr << 16) | ((chip_addr & 0x07) << 8) |
- ((chip_addr >> 3) & 0x0F);
- *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + chan_offset + I2C_CNTRL1) =
- temp;
-
- /* Issue the read command
- * (at this moment all other parameters are 0
- * (size = 1 byte, lane = 0)
- */
-
- *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2) =
- (I2C_CNTRL2_START);
-
- /* Wait until operation completed */
- do {
- /* Read I2C operation status */
- temp = *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2);
-
- if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_START))) {
- if (0 == (temp &
- (I2C_CNTRL2_I2C_CFGERR |
- I2C_CNTRL2_I2C_TO_ERR))
- ) {
- op_status = TSI108_I2C_SUCCESS;
-
- temp = *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE +
- chan_offset +
- I2C_RD_DATA);
-
- *buffer = (u8) (temp & 0xFF);
- } else {
- /* report HW error */
- op_status = TSI108_I2C_IF_ERROR;
-
- DPRINT (("I2C HW error reported: 0x%02x\n", temp));
- }
-
- break;
- }
- } while (to_count--);
- } else {
- op_status = TSI108_I2C_IF_BUSY;
-
- DPRINT (("I2C Transaction start failed: 0x%02x\n", temp));
- }
-
- DPRINT (("I2C read_byte() status: 0x%02x\n", op_status));
- return op_status;
-}
-
-/*
- * I2C Read interface as defined in "include/i2c.h" :
- * chip_addr: I2C chip address, range 0..127
- * (to read from SPD channel EEPROM use (0xD0 ... 0xD7)
- * NOTE: The bit 7 in the chip_addr serves as a channel select.
- * This hack is for enabling "i2c sdram" command on Tsi108 boards
- * without changes to common code. Used for I2C reads only.
- * byte_addr: Memory or register address within the chip
- * alen: Number of bytes to use for addr (typically 1, 2 for larger
- * memories, 0 for register type devices with only one
- * register)
- * buffer: Pointer to destination buffer for data to be read
- * len: How many bytes to read
- *
- * Returns: 0 on success, not 0 on failure
- */
-
-int i2c_read (uchar chip_addr, uint byte_addr, int alen,
- uchar * buffer, int len)
-{
- u32 op_status = TSI108_I2C_PARAM_ERR;
- u32 i2c_if = 0;
-
- /* Hack to support second (SPD) I2C controller (SPD EEPROM read only).*/
- if (0xD0 == (chip_addr & ~0x07)) {
- i2c_if = 1;
- chip_addr &= 0x7F;
- }
- /* Check for valid I2C address */
- if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) {
- while (len--) {
- op_status = i2c_read_byte(i2c_if, chip_addr, byte_addr++, buffer++);
-
- if (TSI108_I2C_SUCCESS != op_status) {
- DPRINT (("I2C read_byte() failed: 0x%02x (%d left)\n", op_status, len));
-
- break;
- }
- }
- }
-
- DPRINT (("I2C read() status: 0x%02x\n", op_status));
- return op_status;
-}
-
-/* I2C write helper function */
-
-static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */
- uint byte_addr, /* Byte address within I2C device */
- uchar * buffer /* pointer to data buffer */
- )
-{
- u32 temp;
- u32 to_count = I2C_DELAY;
- u32 op_status = TSI108_I2C_TIMEOUT_ERR;
-
- /* Check if I2C operation is in progress */
- temp = *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2);
-
- if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) {
- /* Place data into the I2C Tx Register */
- *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_I2C_OFFSET +
- I2C_TX_DATA) = (u32) * buffer;
-
- /* Set device address and operation */
- temp =
- I2C_CNTRL1_I2CWRITE | (byte_addr << 16) |
- ((chip_addr & 0x07) << 8) | ((chip_addr >> 3) & 0x0F);
- *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_I2C_OFFSET +
- I2C_CNTRL1) = temp;
-
- /* Issue the write command (at this moment all other parameters
- * are 0 (size = 1 byte, lane = 0)
- */
-
- *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_I2C_OFFSET +
- I2C_CNTRL2) = (I2C_CNTRL2_START);
-
- op_status = TSI108_I2C_TIMEOUT_ERR;
-
- /* Wait until operation completed */
- do {
- /* Read I2C operation status */
- temp = *(u32 *) (CONFIG_SYS_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2);
-
- if (0 == (temp & (I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) {
- if (0 == (temp &
- (I2C_CNTRL2_I2C_CFGERR |
- I2C_CNTRL2_I2C_TO_ERR))) {
- op_status = TSI108_I2C_SUCCESS;
- } else {
- /* report detected HW error */
- op_status = TSI108_I2C_IF_ERROR;
-
- DPRINT (("I2C HW error reported: 0x%02x\n", temp));
- }
-
- break;
- }
-
- } while (to_count--);
- } else {
- op_status = TSI108_I2C_IF_BUSY;
-
- DPRINT (("I2C Transaction start failed: 0x%02x\n", temp));
- }
-
- return op_status;
-}
-
-/*
- * I2C Write interface as defined in "include/i2c.h" :
- * chip_addr: I2C chip address, range 0..127
- * byte_addr: Memory or register address within the chip
- * alen: Number of bytes to use for addr (typically 1, 2 for larger
- * memories, 0 for register type devices with only one
- * register)
- * buffer: Pointer to data to be written
- * len: How many bytes to write
- *
- * Returns: 0 on success, not 0 on failure
- */
-
-int i2c_write (uchar chip_addr, uint byte_addr, int alen, uchar * buffer,
- int len)
-{
- u32 op_status = TSI108_I2C_PARAM_ERR;
-
- /* Check for valid I2C address */
- if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) {
- while (len--) {
- op_status =
- i2c_write_byte (chip_addr, byte_addr++, buffer++);
-
- if (TSI108_I2C_SUCCESS != op_status) {
- DPRINT (("I2C write_byte() failed: 0x%02x (%d left)\n", op_status, len));
-
- break;
- }
- }
- }
-
- return op_status;
-}
-
-/*
- * I2C interface function as defined in "include/i2c.h".
- * Probe the given I2C chip address by reading single byte from offset 0.
- * Returns 0 if a chip responded, not 0 on failure.
- */
-
-int i2c_probe (uchar chip)
-{
- u32 tmp;
-
- /*
- * Try to read the first location of the chip.
- * The Tsi108 HW doesn't support sending just the chip address
- * and checkong for an <ACK> back.
- */
- return i2c_read (chip, 0, 1, (uchar *)&tmp, 1);
-}
-
-#endif
diff --git a/include/tsi108.h b/include/tsi108.h
deleted file mode 100644
index 8e246b8..0000000
--- a/include/tsi108.h
+++ /dev/null
@@ -1,207 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*****************************************************************************
- * (C) Copyright 2003; Tundra Semiconductor Corp.
- * (C) Copyright 2006; Freescale Semiconductor Corp.
- *****************************************************************************/
-
-/*
- * FILENAME: tsi108.h
- *
- * Originator: Alex Bounine
- *
- * DESCRIPTION:
- * Common definitions for the Tundra Tsi108 bridge chip
- *
- */
-
-#ifndef _TSI108_H_
-#define _TSI108_H_
-
-#define TSI108_HLP_REG_OFFSET (0x0000)
-#define TSI108_PCI_REG_OFFSET (0x1000)
-#define TSI108_CLK_REG_OFFSET (0x2000)
-#define TSI108_PB_REG_OFFSET (0x3000)
-#define TSI108_SD_REG_OFFSET (0x4000)
-#define TSI108_MPIC_REG_OFFSET (0x7400)
-
-#define PB_ID (0x000)
-#define PB_RSR (0x004)
-#define PB_BUS_MS_SELECT (0x008)
-#define PB_ISR (0x00C)
-#define PB_ARB_CTRL (0x018)
-#define PB_PVT_CTRL2 (0x034)
-#define PB_SCR (0x400)
-#define PB_ERRCS (0x404)
-#define PB_AERR (0x408)
-#define PB_REG_BAR (0x410)
-#define PB_OCN_BAR1 (0x414)
-#define PB_OCN_BAR2 (0x418)
-#define PB_SDRAM_BAR1 (0x41C)
-#define PB_SDRAM_BAR2 (0x420)
-#define PB_MCR (0xC00)
-#define PB_MCMD (0xC04)
-
-#define HLP_B0_ADDR (0x000)
-#define HLP_B1_ADDR (0x010)
-#define HLP_B2_ADDR (0x020)
-#define HLP_B3_ADDR (0x030)
-
-#define HLP_B0_MASK (0x004)
-#define HLP_B1_MASK (0x014)
-#define HLP_B2_MASK (0x024)
-#define HLP_B3_MASK (0x034)
-
-#define HLP_B0_CTRL0 (0x008)
-#define HLP_B1_CTRL0 (0x018)
-#define HLP_B2_CTRL0 (0x028)
-#define HLP_B3_CTRL0 (0x038)
-
-#define HLP_B0_CTRL1 (0x00C)
-#define HLP_B1_CTRL1 (0x01C)
-#define HLP_B2_CTRL1 (0x02C)
-#define HLP_B3_CTRL1 (0x03C)
-
-#define PCI_CSR (0x004)
-#define PCI_P2O_BAR0 (0x010)
-#define PCI_P2O_BAR0_UPPER (0x014)
-#define PCI_P2O_BAR2 (0x018)
-#define PCI_P2O_BAR2_UPPER (0x01C)
-#define PCI_P2O_BAR3 (0x020)
-#define PCI_P2O_BAR3_UPPER (0x024)
-
-#define PCI_MISC_CSR (0x040)
-#define PCI_P2O_PAGE_SIZES (0x04C)
-
-#define PCI_PCIX_STAT (0x0F4)
-
-#define PCI_IRP_STAT (0x184)
-
-#define PCI_PFAB_BAR0 (0x204)
-#define PCI_PFAB_BAR0_UPPER (0x208)
-#define PCI_PFAB_IO (0x20C)
-#define PCI_PFAB_IO_UPPER (0x210)
-
-#define PCI_PFAB_MEM32 (0x214)
-#define PCI_PFAB_MEM32_REMAP (0x218)
-#define PCI_PFAB_MEM32_MASK (0x21C)
-
-#define CG_PLL0_CTRL0 (0x210)
-#define CG_PLL0_CTRL1 (0x214)
-#define CG_PLL1_CTRL0 (0x220)
-#define CG_PLL1_CTRL1 (0x224)
-#define CG_PWRUP_STATUS (0x234)
-
-#define MPIC_CSR(n) (0x30C + (n * 0x40))
-
-#define SD_CTRL (0x000)
-#define SD_STATUS (0x004)
-#define SD_TIMING (0x008)
-#define SD_REFRESH (0x00C)
-#define SD_INT_STATUS (0x010)
-#define SD_INT_ENABLE (0x014)
-#define SD_INT_SET (0x018)
-#define SD_D0_CTRL (0x020)
-#define SD_D1_CTRL (0x024)
-#define SD_D0_BAR (0x028)
-#define SD_D1_BAR (0x02C)
-#define SD_ECC_CTRL (0x040)
-#define SD_DLL_STATUS (0x250)
-
-#define TS_SD_CTRL_ENABLE (1 << 31)
-
-#define PB_ERRCS_ES (1 << 1)
-#define PB_ISR_PBS_RD_ERR (1 << 8)
-#define PCI_IRP_STAT_P_CSR (1 << 23)
-
-/*
- * I2C : Register address offset definitions
- */
-#define I2C_CNTRL1 (0x00000000)
-#define I2C_CNTRL2 (0x00000004)
-#define I2C_RD_DATA (0x00000008)
-#define I2C_TX_DATA (0x0000000c)
-
-/*
- * I2C : Register Bit Masks and Reset Values
- * definitions for every register
- */
-
-/* I2C_CNTRL1 : Reset Value */
-#define I2C_CNTRL1_RESET_VALUE (0x0000000a)
-
-/* I2C_CNTRL1 : Register Bits Masks Definitions */
-#define I2C_CNTRL1_DEVCODE (0x0000000f)
-#define I2C_CNTRL1_PAGE (0x00000700)
-#define I2C_CNTRL1_BYTADDR (0x00ff0000)
-#define I2C_CNTRL1_I2CWRITE (0x01000000)
-
-/* I2C_CNTRL1 : Read/Write Bit Mask Definition */
-#define I2C_CNTRL1_RWMASK (0x01ff070f)
-
-/* I2C_CNTRL1 : Unused/Reserved bits Definition */
-#define I2C_CNTRL1_RESERVED (0xfe00f8f0)
-
-/* I2C_CNTRL2 : Reset Value */
-#define I2C_CNTRL2_RESET_VALUE (0x00000000)
-
-/* I2C_CNTRL2 : Register Bits Masks Definitions */
-#define I2C_CNTRL2_SIZE (0x00000003)
-#define I2C_CNTRL2_LANE (0x0000000c)
-#define I2C_CNTRL2_MULTIBYTE (0x00000010)
-#define I2C_CNTRL2_START (0x00000100)
-#define I2C_CNTRL2_WR_STATUS (0x00010000)
-#define I2C_CNTRL2_RD_STATUS (0x00020000)
-#define I2C_CNTRL2_I2C_TO_ERR (0x04000000)
-#define I2C_CNTRL2_I2C_CFGERR (0x08000000)
-#define I2C_CNTRL2_I2C_CMPLT (0x10000000)
-
-/* I2C_CNTRL2 : Read/Write Bit Mask Definition */
-#define I2C_CNTRL2_RWMASK (0x0000011f)
-
-/* I2C_CNTRL2 : Unused/Reserved bits Definition */
-#define I2C_CNTRL2_RESERVED (0xe3fcfee0)
-
-/* I2C_RD_DATA : Reset Value */
-#define I2C_RD_DATA_RESET_VALUE (0x00000000)
-
-/* I2C_RD_DATA : Register Bits Masks Definitions */
-#define I2C_RD_DATA_RBYTE0 (0x000000ff)
-#define I2C_RD_DATA_RBYTE1 (0x0000ff00)
-#define I2C_RD_DATA_RBYTE2 (0x00ff0000)
-#define I2C_RD_DATA_RBYTE3 (0xff000000)
-
-/* I2C_RD_DATA : Read/Write Bit Mask Definition */
-#define I2C_RD_DATA_RWMASK (0x00000000)
-
-/* I2C_RD_DATA : Unused/Reserved bits Definition */
-#define I2C_RD_DATA_RESERVED (0x00000000)
-
-/* I2C_TX_DATA : Reset Value */
-#define I2C_TX_DATA_RESET_VALUE (0x00000000)
-
-/* I2C_TX_DATA : Register Bits Masks Definitions */
-#define I2C_TX_DATA_TBYTE0 (0x000000ff)
-#define I2C_TX_DATA_TBYTE1 (0x0000ff00)
-#define I2C_TX_DATA_TBYTE2 (0x00ff0000)
-#define I2C_TX_DATA_TBYTE3 (0xff000000)
-
-/* I2C_TX_DATA : Read/Write Bit Mask Definition */
-#define I2C_TX_DATA_RWMASK (0xffffffff)
-
-/* I2C_TX_DATA : Unused/Reserved bits Definition */
-#define I2C_TX_DATA_RESERVED (0x00000000)
-
-#define TSI108_I2C_OFFSET 0x7000 /* offset for general use I2C channel */
-#define TSI108_I2C_SDRAM_OFFSET 0x4400 /* offset for SPD I2C channel */
-
-#define I2C_EEPROM_DEVCODE 0xA /* standard I2C EEPROM device code */
-
-/* I2C status codes */
-
-#define TSI108_I2C_SUCCESS 0
-#define TSI108_I2C_PARAM_ERR 1
-#define TSI108_I2C_TIMEOUT_ERR 2
-#define TSI108_I2C_IF_BUSY 3
-#define TSI108_I2C_IF_ERROR 4
-
-#endif /* _TSI108_H_ */