rockchip: rk3588-rock-5b: Drop usb-typec node from u-boot.dtsi
The usb-typec related nodes and props added in the board u-boot.dtsi
file has not yet landed in upstream Linux kernel DT, and they are not
needed for U-Boot to use the USB Type-C port in peripheral mode.
Remove superfluous usb-typec related nodes and props and replace them
with a simple dr_mode and maximum-speed prop to cleanup the board
u-boot.dtsi file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
diff --git a/arch/arm/dts/rk3588-rock-5b-u-boot.dtsi b/arch/arm/dts/rk3588-rock-5b-u-boot.dtsi
index d6020ca..69914f4 100644
--- a/arch/arm/dts/rk3588-rock-5b-u-boot.dtsi
+++ b/arch/arm/dts/rk3588-rock-5b-u-boot.dtsi
@@ -4,32 +4,12 @@
*/
#include "rk3588-u-boot.dtsi"
-#include <dt-bindings/usb/pd.h>
-
-/ {
- vcc12v_dcin: vcc12v-dcin-regulator {
- compatible = "regulator-fixed";
- regulator-name = "vcc12v_dcin";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- };
-};
&fspim2_pins {
bootph-pre-ram;
bootph-some-ram;
};
-&pinctrl {
- usb {
- usbc0_int: usbc0-int {
- rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-};
-
&sdhci {
cap-mmc-highspeed;
mmc-hs200-1_8v;
@@ -76,26 +56,7 @@
};
&usbdp_phy0 {
- orientation-switch;
- mode-switch;
- sbu1-dc-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
- sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
status = "okay";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- usbdp_phy0_typec_ss: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&usbc0_ss>;
- };
-
- usbdp_phy0_typec_sbu: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&usbc0_sbu>;
- };
- };
};
&usbdp_phy0_u3 {
@@ -103,74 +64,11 @@
};
&usb_host0_xhci {
- usb-role-switch;
+ dr_mode = "peripheral";
+ maximum-speed = "high-speed";
status = "okay";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- usb_host0_xhci_drd_sw: endpoint {
- remote-endpoint = <&usbc0_hs>;
- };
- };
};
&usb_host1_xhci {
status = "okay";
};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4m1_xfer>;
- status = "okay";
-
- usbc0: usb-typec@22 {
- compatible = "fcs,fusb302";
- reg = <0x22>;
- interrupt-parent = <&gpio3>;
- interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&usbc0_int>;
- vbus-supply = <&vcc12v_dcin>;
- status = "okay";
-
- usb_con: connector {
- compatible = "usb-c-connector";
- label = "USB-C";
- data-role = "dual";
- power-role = "sink";
- try-power-role = "sink";
- op-sink-microwatt = <1000000>;
- sink-pdos =
- <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>,
- <PDO_VAR(5000, 20000, 5000)>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- usbc0_hs: endpoint {
- remote-endpoint = <&usb_host0_xhci_drd_sw>;
- };
- };
-
- port@1 {
- reg = <1>;
- usbc0_ss: endpoint {
- remote-endpoint = <&usbdp_phy0_typec_ss>;
- };
- };
-
- port@2 {
- reg = <2>;
- usbc0_sbu: endpoint {
- remote-endpoint = <&usbdp_phy0_typec_sbu>;
- };
- };
- };
- };
- };
-};