include/configs: Use new CONFIG_CMD_* in various 5200 board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h
index d8686dd..ba2daf7 100644
--- a/include/configs/Total5200.h
+++ b/include/configs/Total5200.h
@@ -48,11 +48,6 @@
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Serial console configuration
*/
@@ -63,7 +58,6 @@
/*
* Video console
*/
-#if 1
#define CONFIG_VIDEO
#define CONFIG_VIDEO_SED13806
#define CONFIG_VIDEO_SED13806_16BPP
@@ -76,10 +70,6 @@
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_SPLASH_SCREEN
-#define ADD_VIDEO_CMD CFG_CMD_BMP
-#else
-#define ADD_VIDEO_CMD 0
-#endif
#ifdef CONFIG_MPC5200 /* MGT5100 PCI is not supported yet. */
/*
@@ -105,12 +95,9 @@
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#define ADD_PCI_CMD CFG_CMD_PCI
-
#else /* MGT5100 */
#define CONFIG_MII 1
-#define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */
#endif
@@ -119,29 +106,27 @@
#define CONFIG_DOS_PARTITION
/* USB */
-#if 1
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
-#else
-#define ADD_USB_CMD 0
-#endif
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_PING | \
- CFG_CMD_I2C | \
- CFG_CMD_EEPROM | \
- CFG_CMD_FAT | \
- CFG_CMD_IDE | \
- ADD_VIDEO_CMD | \
- ADD_PCI_CMD | \
- ADD_USB_CMD)
+#include <config_cmd_default.h>
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#if definded(CONFIG_MPC5200)
+ #define CONFIG_CMD_PCI
+#endif
+
+#define CONFIG_CMD_BMP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
#if (TEXT_BASE == 0xFE000000) /* Boot low */
# define CFG_LOWBOOT 1
@@ -303,7 +288,7 @@
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
@@ -319,6 +304,12 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+
/*
* Various low-level settings
*/