imx: Add variscite DART-6UL Evaluation Kit
Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.
CPU: Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@02020000
Out: serial@02020000
Err: serial@02020000
Net: FEC0
Working:
- Eth0
- i2c
- MMC/SD
- eMMC
- USB host
- UART 1
Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
diff --git a/include/configs/dart_6ul.h b/include/configs/dart_6ul.h
new file mode 100644
index 0000000..fb1b899
--- /dev/null
+++ b/include/configs/dart_6ul.h
@@ -0,0 +1,131 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Board configuration file for Variscite DART-6UL Evaluation Kit
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+#ifndef __DART_6UL_H
+#define __DART_6UL_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+/* NAND pin conflicts with usdhc2 */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_SYS_FSL_USDHC_NUM 1
+#else
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+#endif
+
+#ifdef CONFIG_CMD_NET
+#define CONFIG_FEC_ENET_DEV 0
+
+#if (CONFIG_FEC_ENET_DEV == 0)
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR 0x1
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_ETHPRIME "eth0"
+#elif (CONFIG_FEC_ENET_DEV == 1)
+#define IMX_FEC_BASE ENET2_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR 0x3
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_ETHPRIME "eth1"
+#endif
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
+
+/* Environment settings */
+#define CONFIG_ENV_SIZE SZ_8K
+#define CONFIG_ENV_OFFSET (14 * SZ_64K)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* Environment in SD */
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 0
+#define MMC_ROOTFS_DEV 0
+#define MMC_ROOTFS_PART 2
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* I2C configs */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_SPEED 100000
+#endif
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE SZ_512M
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+#define CONFIG_IMX_THERMAL
+
+#define ENV_MMC \
+ "mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \
+ "mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \
+ "fitpart=1\0" \
+ "bootdelay=3\0" \
+ "silent=1\0" \
+ "optargs=rw rootwait\0" \
+ "mmcautodetect=yes\0" \
+ "mmcrootfstype=ext4\0" \
+ "mmcfit_name=fitImage\0" \
+ "mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \
+ "${mmcfit_name}\0" \
+ "mmcargs=setenv bootargs " \
+ "root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \
+ "console=${console} rootfstype=${mmcrootfstype}\0" \
+ "mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_high=0xffffffff\0" \
+ "console=ttymxc0,115200n8\0" \
+ "addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
+ "fit_addr=0x82000000\0" \
+ ENV_MMC
+
+#define CONFIG_BOOTCOMMAND "run mmc_mmc_fit"
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+#endif /* __DART_6UL_H */