TQM85xx: Support for Intel 82527 compatible CAN controller
This patch adds initialization of the UPMC RAM to support up to two
Intel 82527 compatible CAN controller on the TQM85xx modules.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
diff --git a/board/tqc/tqm85xx/law.c b/board/tqc/tqm85xx/law.c
index d937700..ad35464 100644
--- a/board/tqc/tqm85xx/law.c
+++ b/board/tqc/tqm85xx/law.c
@@ -35,6 +35,7 @@
* 0xc000_0000 0xdfff_ffff RapidIO 512M
* 0xe000_0000 0xe000_ffff CCSR 1M
* 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
+ * 0xe300_0000 0xe3ff_ffff CAN 16M
* 0xf800_0000 0xf80f_ffff BCSR 1M
* 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M
*
@@ -49,6 +50,9 @@
SET_LAW_ENTRY (3, CFG_LBC_FLASH_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
SET_LAW_ENTRY (4, CFG_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI),
SET_LAW_ENTRY (5, CFG_RIO_MEM_BASE, LAWAR_SIZE_512M, LAW_TRGT_IF_RIO),
+#ifdef CONFIG_CAN_DRIVER
+ SET_LAW_ENTRY (6, CFG_CAN_BASE, LAWAR_SIZE_16M, LAW_TRGT_IF_LBC),
+#endif /* CONFIG_CAN_DRIVER */
};
int num_law_entries = ARRAY_SIZE (law_table);
diff --git a/board/tqc/tqm85xx/tlb.c b/board/tqc/tqm85xx/tlb.c
index 3e29062..dc36201 100644
--- a/board/tqc/tqm85xx/tlb.c
+++ b/board/tqc/tqm85xx/tlb.c
@@ -95,6 +95,7 @@
* TLB 6: 64M Non-cacheable, guarded
* 0xe0000000 1M CCSRBAR
* 0xe2000000 16M PCI1 IO
+ * 0xe3000000 16M CAN
*/
SET_TLB_ENTRY (1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
diff --git a/board/tqc/tqm85xx/tqm85xx.c b/board/tqc/tqm85xx/tqm85xx.c
index a45df2b..4fb9c11 100644
--- a/board/tqc/tqm85xx/tqm85xx.c
+++ b/board/tqc/tqm85xx/tqm85xx.c
@@ -31,6 +31,7 @@
#include <pci.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
+#include <asm/io.h>
#include <ioports.h>
#include <flash.h>
@@ -333,6 +334,27 @@
return 0;
}
+#ifdef CONFIG_CAN_DRIVER
+/*
+ * Initialize UPMC RAM
+ */
+static void upmc_write (u_char addr, uint val)
+{
+ volatile ccsr_lbc_t *lbc = (void *)(CFG_MPC85xx_LBC_ADDR);
+
+ out_be32 (&lbc->mdr, val);
+
+ clrsetbits_be32(&lbc->mcmr, MxMR_MAD_MSK,
+ MxMR_OP_WARR | (addr & MxMR_MAD_MSK));
+
+ /* dummy access to perform write */
+ out_8 ((void __iomem *)CFG_CAN_BASE, 0);
+
+ /* normal operation */
+ clrbits_be32(&lbc->mcmr, MxMR_OP_WARR);
+}
+#endif /* CONFIG_CAN_DRIVER */
+
/*
* Initialize Local Bus
*/
@@ -389,6 +411,41 @@
gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
asm ("sync;isync;msync");
}
+
+#ifdef CONFIG_CAN_DRIVER
+ /*
+ * According to timing specifications EAD must be
+ * set if Local Bus Clock is > 83 MHz.
+ */
+ if (lbc_hz > 83)
+ out_be32 (&lbc->or2, CFG_OR2_CAN | OR_UPM_EAD);
+ else
+ out_be32 (&lbc->or2, CFG_OR2_CAN);
+ out_be32 (&lbc->br2, CFG_BR2_CAN);
+
+ /* LGPL4 is UPWAIT */
+ out_be32(&lbc->mcmr, MxMR_DSx_3_CYCL | MxMR_GPL_x4DIS | MxMR_WLFx_3X);
+
+ /* Initialize UPMC for CAN: single read */
+ upmc_write (0x00, 0xFFFFED00);
+ upmc_write (0x01, 0xCCFFCC00);
+ upmc_write (0x02, 0x00FFCF00);
+ upmc_write (0x03, 0x00FFCF00);
+ upmc_write (0x04, 0x00FFDC00);
+ upmc_write (0x05, 0x00FFCF00);
+ upmc_write (0x06, 0x00FFED00);
+ upmc_write (0x07, 0x3FFFCC07);
+
+ /* Initialize UPMC for CAN: single write */
+ upmc_write (0x18, 0xFFFFED00);
+ upmc_write (0x19, 0xCCFFEC00);
+ upmc_write (0x1A, 0x00FFED80);
+ upmc_write (0x1B, 0x00FFED80);
+ upmc_write (0x1C, 0x00FFFC00);
+ upmc_write (0x1D, 0x0FFFEC00);
+ upmc_write (0x1E, 0x0FFFEF00);
+ upmc_write (0x1F, 0x3FFFEC05);
+#endif /* CONFIG_CAN_DRIVER */
}
#if defined(CONFIG_PCI)