Initial revision
diff --git a/include/configs/dnp1110.h b/include/configs/dnp1110.h
new file mode 100644
index 0000000..673e767
--- /dev/null
+++ b/include/configs/dnp1110.h
@@ -0,0 +1,148 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Rolf Offermanns <rof@sysgo.de>
+ *
+ * Configuation settings for the SSV DNP1110 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start armboot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#define CONFIG_INIT_CRITICAL /* undef for developing */
+#undef CONFIG_INIT_CRITICAL /* undef for developing */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_SA1110 1 /* This is an SA1110 CPU */
+#define CONFIG_DNP1110 1 /* on an DNP/1110 Board */
+
+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_DRIVER_SMC91111
+#define CONFIG_SMC91111_BASE 0x20000300
+
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL1 1 /* we use SERIAL 1 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,115200"
+#define CONFIG_ETHADDR 02:80:ad:20:31:b8
+#define CONFIG_NETMASK 255.255.0.0
+#define CONFIG_IPADDR 172.22.2.23
+#define CONFIG_SERVERIP 172.22.2.22
+#define CONFIG_BOOTFILE "elinos-dnp1110"
+#define CONFIG_BOOTCOMMAND "tftp; bootm"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "DNP1110 # " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0xc0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
+
+#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR 0xc0200000 /* default load address */
+
+#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CFG_CPUSPEED 0x0b /* set core clock to 220 MHz */
+
+ /* valid baudrates */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 banks of DRAM */
+#define PHYS_SDRAM_1 0xc0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
+
+
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */
+
+#define CFG_FLASH_BASE PHYS_FLASH_1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT (31+8) /* max number of sectors on one chip */
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000) /* Addr of Environment Sector */
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/ep7312.h b/include/configs/ep7312.h
new file mode 100644
index 0000000..6b30ce1
--- /dev/null
+++ b/include/configs/ep7312.h
@@ -0,0 +1,155 @@
+/*
+ * (C) Copyright 2000
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the EP7312 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start armboot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#define CONFIG_INIT_CRITICAL /* undef for developing */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_ARM7 1 /* This is a ARM7 CPU */
+#define CONFIG_EP7312 1 /* on an EP7312 Board */
+#define CONFIG_ARM_THUMB 1 /* this is an ARM720TDMI */
+#undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */
+
+#undef CONFIG_USE_IRQ /* don't need them anymore */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
+#define CS8900_BASE 0x20000000
+#define CS8900_BUS16 1
+#undef CS8900_BUS32
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE 9600
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_JFFS2)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "devfs=mount root=ramfs console=ttyS0,9600"
+#define CONFIG_ETHADDR 08:00:3e:21:c7:f7
+/*#define CONFIG_NETMASK 255.255.0.0 */
+/*#define CONFIG_IPADDR 172.22.2.128 */
+/*#define CONFIG_SERVERIP 172.22.2.126 */
+/*#define CONFIG_BOOTFILE "impa7" */
+#define CONFIG_BOOTCOMMAND "bootp;bootm"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "EP7312 # " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0xc0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
+
+#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR 0xc0500000 /* default load address */
+
+#define CFG_HZ 2000 /* decrementer freq: 2 kHz */
+
+ /* valid baudrates */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 2 banks of DRAM */
+#define PHYS_SDRAM_1 0xc0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */
+
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */
+
+#define CFG_FLASH_BASE PHYS_FLASH_1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x20000) /* Addr of Environment Sector */
+#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
+
+/* Flash banks JFFS2 should use */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_FIRST_SECTOR 2
+#define CFG_JFFS2_NUM_BANKS 1
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/impa7.h b/include/configs/impa7.h
new file mode 100644
index 0000000..99e0a4b
--- /dev/null
+++ b/include/configs/impa7.h
@@ -0,0 +1,157 @@
+/*
+ * (C) Copyright 2000
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the implementa impA7 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start armboot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#define CONFIG_INIT_CRITICAL /* undef for developing */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_ARM7 1 /* This is a ARM7 CPU */
+#define CONFIG_IMPA7 1 /* on an impA7 Board */
+#define CONFIG_ARM_THUMB 1 /* this is an ARM720TDMI */
+#define CONFIG_ARM7_REVD 1 /* enable ARM720 REV.D Workarounds */
+
+#undef CONFIG_USE_IRQ /* don't need them anymore */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
+#define CS8900_BASE 0x20000000
+#define CS8900_BUS32 1
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE 9600
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_JFFS2)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "devfs=mount root=ramfs console=ttyS0,9600"
+/*#define CONFIG_ETHADDR 08:00:3e:26:0a:5a */
+/*#define CONFIG_NETMASK 255.255.0.0 */
+/*#define CONFIG_IPADDR 172.22.2.128 */
+/*#define CONFIG_SERVERIP 172.22.2.126 */
+/*#define CONFIG_BOOTFILE "impa7" */
+#define CONFIG_BOOTCOMMAND "bootp;bootm"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "impA7 # " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0xc0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
+
+#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR 0xc1000000 /* default load address */
+
+#define CFG_HZ 2000 /* decrementer freq: 2 kHz */
+
+ /* valid baudrates */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* we have 2 banks of DRAM */
+#define PHYS_SDRAM_1 0xc0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x00800000 /* 8 MB */
+#define PHYS_SDRAM_2 0xc1000000 /* SDRAM Bank #2 */
+#define PHYS_SDRAM_2_SIZE 0x00800000 /* 8 MB */
+
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_2 0x10000000 /* Flash Bank #2 */
+#define PHYS_FLASH_SIZE 0x00800000 /* 16 MB */
+
+#define CFG_FLASH_BASE PHYS_FLASH_1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000) /* Addr of Environment Sector */
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+/* Flash banks JFFS2 should use */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_FIRST_SECTOR 8
+#define CFG_JFFS2_NUM_BANKS 2
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/lart.h b/include/configs/lart.h
new file mode 100644
index 0000000..aa2dfa0
--- /dev/null
+++ b/include/configs/lart.h
@@ -0,0 +1,153 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the LART board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start armboot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#define CONFIG_INIT_CRITICAL /* undef for developing */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_SA1100 1 /* This is an SA1100 CPU */
+#define CONFIG_LART 1 /* on an LART Board */
+
+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
+#define CS8900_BASE 0x20008300
+#define CS8900_BUS16 1
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL3 1 /* we use SERIAL 3 on LART */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE 9600
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,9600"
+#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
+#define CONFIG_NETMASK 255.255.0.0
+#define CONFIG_IPADDR 172.22.2.131
+#define CONFIG_SERVERIP 172.22.2.126
+#define CONFIG_BOOTFILE "elinos-lart"
+#define CONFIG_BOOTCOMMAND "tftp; bootm"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "LART # " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0xc0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
+
+#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR 0xc8000000 /* default load address */
+
+#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CFG_CPUSPEED 0x0b /* set core clock to 220 MHz */
+
+ /* valid baudrates */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */
+#define PHYS_SDRAM_1 0xc0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x00800000 /* 8 MB */
+#define PHYS_SDRAM_2 0xc1000000 /* SDRAM Bank #2 */
+#define PHYS_SDRAM_2_SIZE 0x00800000 /* 8 MB */
+#define PHYS_SDRAM_3 0xc8000000 /* SDRAM Bank #3 */
+#define PHYS_SDRAM_3_SIZE 0x00800000 /* 8 MB */
+#define PHYS_SDRAM_4 0xc9000000 /* SDRAM Bank #4 */
+#define PHYS_SDRAM_4_SIZE 0x00800000 /* 8 MB */
+
+
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE 0x00400000 /* 4 MB */
+
+#define CFG_FLASH_BASE PHYS_FLASH_1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT (31+8) /* max number of sectors on one chip */
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000) /* Addr of Environment Sector */
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/lubbock.h b/include/configs/lubbock.h
new file mode 100644
index 0000000..eb5ed2f
--- /dev/null
+++ b/include/configs/lubbock.h
@@ -0,0 +1,220 @@
+/*
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the LUBBOCK board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start armboot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#define CONFIG_INIT_CRITICAL /* undef for developing */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_PXA250 1 /* This is an PXA250 CPU */
+#define CONFIG_LUBBOCK 1 /* on an LUBBOCK Board */
+
+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_FFUART 1 /* we use FFUART on LUBBOCK */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,9600"
+#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
+#define CONFIG_NETMASK 255.255.0.0
+#define CONFIG_IPADDR 192.168.0.21
+#define CONFIG_SERVERIP 192.168.0.250
+#define CONFIG_BOOTCOMMAND "FIXME"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+
+#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR 0xa8000000 /* default load address */
+
+#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CFG_CPUSPEED 0x141 /* set core clock to 200/200/100 MHz */
+
+ /* valid baudrates */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+#define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */
+#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */
+#define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */
+#define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */
+#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */
+#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */
+
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_2 0x04000000 /* Flash Bank #1 */
+#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */
+
+#define CFG_DRAM_BASE 0xa0000000
+#define CFG_DRAM_SIZE 0x04000000
+
+#define CFG_FLASH_BASE PHYS_FLASH_1
+
+#define FPGA_REGS_BASE_PHYSICAL 0x08000000
+
+/*
+ * GPIO settings
+ */
+#define CFG_GPSR0_VAL 0x00008000
+#define CFG_GPSR1_VAL 0x00FC0382
+#define CFG_GPSR2_VAL 0x0001FFFF
+#define CFG_GPCR0_VAL 0x00000000
+#define CFG_GPCR1_VAL 0x00000000
+#define CFG_GPCR2_VAL 0x00000000
+#define CFG_GPDR0_VAL 0x0060A800
+#define CFG_GPDR1_VAL 0x00FF0382
+#define CFG_GPDR2_VAL 0x0001C000
+#define CFG_GAFR0_L_VAL 0x98400000
+#define CFG_GAFR0_U_VAL 0x00002950
+#define CFG_GAFR1_L_VAL 0x000A9558
+#define CFG_GAFR1_U_VAL 0x0005AAAA
+#define CFG_GAFR2_L_VAL 0xA0000000
+#define CFG_GAFR2_U_VAL 0x00000002
+
+#define CFG_PSSR_VAL 0x20
+
+/*
+ * Memory settings
+ */
+#define CFG_MSC0_VAL 0x23F223F2
+#define CFG_MSC1_VAL 0x3FF1A441
+#define CFG_MSC2_VAL 0x7FF17FF1
+#define CFG_MDCNFG_VAL 0x00001AC9
+#define CFG_MDREFR_VAL 0x000BC018
+#define CFG_MDREFR_VAL_100 0x00018018
+#define CFG_MDMRS_VAL 0x00000000
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CFG_MECR_VAL 0x00000000
+#define CFG_MCMEM0_VAL 0x00010504
+#define CFG_MCMEM1_VAL 0x00010504
+#define CFG_MCATT0_VAL 0x00010504
+#define CFG_MCATT1_VAL 0x00010504
+#define CFG_MCIO0_VAL 0x00004715
+#define CFG_MCIO1_VAL 0x00004715
+
+#define _LED 0x08000010
+#define LED_BLANK (0x08000040)
+
+/*
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+
+/* FIXME */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000) /* Addr of Environment Sector */
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+
+/*
+ * FPGA Offsets
+ */
+#define WHOAMI_OFFSET 0x00
+#define HEXLED_OFFSET 0x10
+#define BLANKLED_OFFSET 0x40
+#define DISCRETELED_OFFSET 0x40
+#define CNFG_SWITCHES_OFFSET 0x50
+#define USER_SWITCHES_OFFSET 0x60
+#define MISC_WR_OFFSET 0x80
+#define MISC_RD_OFFSET 0x90
+#define INT_MASK_OFFSET 0xC0
+#define INT_CLEAR_OFFSET 0xD0
+#define GP_OFFSET 0x100
+
+#endif /* __CONFIG_H */