- Add MPC5XXX register definition MPC5XXX_WU_GPIO_DATA_I and change the
MPC5XXX_WU_GPIO_DATA macro to MPC5XXX_WU_GPIO_DATA_O (per MPC5200 User's
Manual). Replace the uses of MPC5XXX_WU_GPIO_DATA with
MPC5XXX_WU_GPIO_DATA_O for affected boards.
- Add defintions for some MPC5XXX GPIO pins.
diff --git a/board/inka4x0/inka4x0.c b/board/inka4x0/inka4x0.c
index 29878f9..d670cc3 100644
--- a/board/inka4x0/inka4x0.c
+++ b/board/inka4x0/inka4x0.c
@@ -173,9 +173,6 @@
*(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
}
-#define GPIO_WKUP_7 0x80000000UL
-#define GPIO_PSC3_9 0x04000000UL
-
int misc_init_f (void)
{
uchar tmp[10];
@@ -218,13 +215,13 @@
*(vu_long *)MPC5XXX_WU_GPIO_DIR |= 0xc4000000;
/* Set LR mirror bit because it is low-active */
- *(vu_long *)MPC5XXX_WU_GPIO_DATA |= GPIO_WKUP_7;
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WKUP_7;
/*
* Reset Coral-P graphics controller
*/
*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
- *(vu_long *) MPC5XXX_WU_GPIO_DATA |= GPIO_PSC3_9;
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC3_9;
return 0;
}
@@ -241,8 +238,6 @@
#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
-#define GPIO_PSC1_4 0x01000000UL
-
void init_ide_reset (void)
{
debug ("init_ide_reset\n");
@@ -251,7 +246,7 @@
*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
/* Deassert reset */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA |= GPIO_PSC1_4;
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
}
void ide_set_reset (int idereset)
@@ -259,11 +254,11 @@
debug ("ide_reset(%d)\n", idereset);
if (idereset) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA &= ~GPIO_PSC1_4;
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
/* Make a delay. MPC5200 spec says 25 usec min */
udelay(500000);
} else {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA |= GPIO_PSC1_4;
+ *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
}
}
#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */