mx5: Optimize lowlevel_init code size
Optimize mx5 lowlevel_init.S code size:
- Compute values at compile time rather than at runtime where possible.
- Assign r4 to hold the zero value rather than setting registers to 0 again and
again.
- Associate a function to setup_pll rather than expanding its large macro code
multiple times.
- Allocate constant values in section only if used.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
diff --git a/arch/arm/cpu/armv7/mx5/lowlevel_init.S b/arch/arm/cpu/armv7/mx5/lowlevel_init.S
index a40b84f..529e35b 100644
--- a/arch/arm/cpu/armv7/mx5/lowlevel_init.S
+++ b/arch/arm/cpu/armv7/mx5/lowlevel_init.S
@@ -24,6 +24,8 @@
#include <generated/asm-offsets.h>
#include <linux/linkage.h>
+.section ".text.init", "x"
+
/*
* L2CC Cache setup/invalidation/disable
*/
@@ -34,15 +36,14 @@
mcr 15, 0, r0, c1, c0, 1
/* reconfigure L2 cache aux control reg */
- mov r0, #0xC0 /* tag RAM */
- add r0, r0, #0x4 /* data RAM */
- orr r0, r0, #1 << 24 /* disable write allocate delay */
- orr r0, r0, #1 << 23 /* disable write allocate combine */
- orr r0, r0, #1 << 22 /* disable write allocate */
+ ldr r0, =0xC0 | /* tag RAM */ \
+ 0x4 | /* data RAM */ \
+ 1 << 24 | /* disable write allocate delay */ \
+ 1 << 23 | /* disable write allocate combine */ \
+ 1 << 22 /* disable write allocate */
#if defined(CONFIG_MX51)
- ldr r1, =0x0
- ldr r3, [r1, #ROM_SI_REV]
+ ldr r3, [r4, #ROM_SI_REV]
cmp r3, #0x10
/* disable write combine for TO 2 and lower revs */
@@ -84,8 +85,7 @@
ldr r1, =0x00000203
str r1, [r0, #0x40]
- ldr r1, =0x0
- str r1, [r0, #0x44]
+ str r4, [r0, #0x44]
ldr r1, =0x00120125
str r1, [r0, #0x9C]
@@ -98,20 +98,29 @@
.macro setup_pll pll, freq
ldr r0, =\pll
+ adr r2, W_DP_\freq
+ bl setup_pll_func
+.endm
+
+#define W_DP_OP 0
+#define W_DP_MFD 4
+#define W_DP_MFN 8
+
+setup_pll_func:
ldr r1, =0x00001232
str r1, [r0, #PLL_DP_CTL] /* Set DPLL ON (set UPEN bit): BRMO=1 */
mov r1, #0x2
str r1, [r0, #PLL_DP_CONFIG] /* Enable auto-restart AREN bit */
- ldr r1, W_DP_OP_\freq
+ ldr r1, [r2, #W_DP_OP]
str r1, [r0, #PLL_DP_OP]
str r1, [r0, #PLL_DP_HFS_OP]
- ldr r1, W_DP_MFD_\freq
+ ldr r1, [r2, #W_DP_MFD]
str r1, [r0, #PLL_DP_MFD]
str r1, [r0, #PLL_DP_HFS_MFD]
- ldr r1, W_DP_MFN_\freq
+ ldr r1, [r2, #W_DP_MFN]
str r1, [r0, #PLL_DP_MFN]
str r1, [r0, #PLL_DP_HFS_MFN]
@@ -120,12 +129,13 @@
1: ldr r1, [r0, #PLL_DP_CTL]
ands r1, r1, #0x1
beq 1b
-.endm
+
+ /* r10 saved upper lr */
+ mov pc, lr
.macro setup_pll_errata pll, freq
ldr r2, =\pll
- mov r1, #0x0
- str r1, [r2, #PLL_DP_CONFIG] /* Disable auto-restart AREN bit */
+ str r4, [r2, #PLL_DP_CONFIG] /* Disable auto-restart AREN bit */
ldr r1, =0x00001236
str r1, [r2, #PLL_DP_CTL] /* Restart PLL with PLM=1 */
1: ldr r1, [r2, #PLL_DP_CTL] /* Wait for lock */
@@ -158,10 +168,9 @@
/* Gate of clocks to the peripherals first */
ldr r1, =0x3FFFFFFF
str r1, [r0, #CLKCTL_CCGR0]
- ldr r1, =0x0
- str r1, [r0, #CLKCTL_CCGR1]
- str r1, [r0, #CLKCTL_CCGR2]
- str r1, [r0, #CLKCTL_CCGR3]
+ str r4, [r0, #CLKCTL_CCGR1]
+ str r4, [r0, #CLKCTL_CCGR2]
+ str r4, [r0, #CLKCTL_CCGR3]
ldr r1, =0x00030000
str r1, [r0, #CLKCTL_CCGR4]
@@ -184,11 +193,10 @@
#else
ldr r1, =0x3FFFFFFF
str r1, [r0, #CLKCTL_CCGR0]
- ldr r1, =0x0
- str r1, [r0, #CLKCTL_CCGR1]
- str r1, [r0, #CLKCTL_CCGR2]
- str r1, [r0, #CLKCTL_CCGR3]
- str r1, [r0, #CLKCTL_CCGR7]
+ str r4, [r0, #CLKCTL_CCGR1]
+ str r4, [r0, #CLKCTL_CCGR2]
+ str r4, [r0, #CLKCTL_CCGR3]
+ str r4, [r0, #CLKCTL_CCGR7]
ldr r1, =0x00030000
str r1, [r0, #CLKCTL_CCGR4]
@@ -214,8 +222,7 @@
/* Switch peripheral to PLL 3 */
ldr r0, =CCM_BASE_ADDR
- ldr r1, =0x000010C0
- orr r1,r1,#CONFIG_SYS_DDR_CLKSEL
+ ldr r1, =0x000010C0 | CONFIG_SYS_DDR_CLKSEL
str r1, [r0, #CLKCTL_CBCMR]
ldr r1, =0x13239145
str r1, [r0, #CLKCTL_CBCDR]
@@ -225,8 +232,7 @@
ldr r0, =CCM_BASE_ADDR
ldr r1, =0x19239145
str r1, [r0, #CLKCTL_CBCDR]
- ldr r1, =0x000020C0
- orr r1,r1,#CONFIG_SYS_DDR_CLKSEL
+ ldr r1, =0x000020C0 | CONFIG_SYS_DDR_CLKSEL
str r1, [r0, #CLKCTL_CBCMR]
#endif
setup_pll PLL3_BASE_ADDR, 216
@@ -240,8 +246,7 @@
#if defined(CONFIG_MX51)
/* Run 3.0 at Full speed, for other TO's wait till we increase VDDGP */
- ldr r1, =0x0
- ldr r3, [r1, #ROM_SI_REV]
+ ldr r3, [r4, #ROM_SI_REV]
cmp r3, #0x10
movls r1, #0x1
movhi r1, #0
@@ -251,14 +256,12 @@
str r1, [r0, #CLKCTL_CACRR]
/* Switch ARM back to PLL 1 */
- mov r1, #0
- str r1, [r0, #CLKCTL_CCSR]
+ str r4, [r0, #CLKCTL_CCSR]
#if defined(CONFIG_MX51)
/* setup the rest */
/* Use lp_apm (24MHz) source for perclk */
- ldr r1, =0x000020C2
- orr r1,r1,#CONFIG_SYS_DDR_CLKSEL
+ ldr r1, =0x000020C2 | CONFIG_SYS_DDR_CLKSEL
str r1, [r0, #CLKCTL_CBCMR]
/* ddr clock from PLL 1, all perclk dividers are 1 since using 24MHz */
ldr r1, =CONFIG_SYS_CLKTL_CBCDR
@@ -289,7 +292,6 @@
ldr r0, =CCM_BASE_ADDR
ldr r1, =0x00808145
orr r1, r1, #2 << 10
- orr r1, r1, #0 << 16
orr r1, r1, #1 << 19
str r1, [r0, #CLKCTL_CBCDR]
@@ -310,8 +312,7 @@
cmp r1, #0x0
bne 1b
- mov r1, #0x0
- str r1, [r0, #CLKCTL_CCDR]
+ str r4, [r0, #CLKCTL_CCDR]
/* for cko - for ARM div by 8 */
mov r1, #0x000A0000
@@ -325,9 +326,10 @@
strh r1, [r0]
.endm
-.section ".text.init", "x"
-
ENTRY(lowlevel_init)
+ mov r10, lr
+ mov r4, #0 /* Fix R4 to 0 */
+
#if defined(CONFIG_MX51)
ldr r0, =GPIO1_BASE_ADDR
ldr r1, [r0, #0x0]
@@ -346,21 +348,25 @@
init_clock
- /* r12 saved upper lr*/
- mov pc,lr
+ mov pc, r10
ENDPROC(lowlevel_init)
/* Board level setting value */
-W_DP_OP_864: .word DP_OP_864
-W_DP_MFD_864: .word DP_MFD_864
-W_DP_MFN_864: .word DP_MFN_864
+#if defined(CONFIG_MX51_PLL_ERRATA)
+W_DP_864: .word DP_OP_864
+ .word DP_MFD_864
+ .word DP_MFN_864
W_DP_MFN_800_DIT: .word DP_MFN_800_DIT
-W_DP_OP_800: .word DP_OP_800
-W_DP_MFD_800: .word DP_MFD_800
-W_DP_MFN_800: .word DP_MFN_800
-W_DP_OP_665: .word DP_OP_665
-W_DP_MFD_665: .word DP_MFD_665
-W_DP_MFN_665: .word DP_MFN_665
-W_DP_OP_216: .word DP_OP_216
-W_DP_MFD_216: .word DP_MFD_216
-W_DP_MFN_216: .word DP_MFN_216
+#else
+W_DP_800: .word DP_OP_800
+ .word DP_MFD_800
+ .word DP_MFN_800
+#endif
+#if defined(CONFIG_MX51)
+W_DP_665: .word DP_OP_665
+ .word DP_MFD_665
+ .word DP_MFN_665
+#endif
+W_DP_216: .word DP_OP_216
+ .word DP_MFD_216
+ .word DP_MFN_216