usb: sunxi: Switch to use generic-phy
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
diff --git a/drivers/usb/musb-new/sunxi.c b/drivers/usb/musb-new/sunxi.c
index 5728a3f..08de9c6 100644
--- a/drivers/usb/musb-new/sunxi.c
+++ b/drivers/usb/musb-new/sunxi.c
@@ -17,10 +17,11 @@
*/
#include <common.h>
#include <dm.h>
+#include <generic-phy.h>
+#include <phy-sun4i-usb.h>
#include <asm/arch/cpu.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
-#include <asm/arch/usb_phy.h>
#include <asm-generic/gpio.h>
#include <dm/lists.h>
#include <dm/root.h>
@@ -86,6 +87,7 @@
struct sunxi_ccm_reg *ccm;
struct sunxi_musb_config *cfg;
struct device dev;
+ struct phy *phy;
};
#define to_sunxi_glue(d) container_of(d, struct sunxi_glue, dev)
@@ -218,6 +220,7 @@
static int sunxi_musb_enable(struct musb *musb)
{
+ struct sunxi_glue *glue = to_sunxi_glue(musb->controller);
int ret;
pr_debug("%s():\n", __func__);
@@ -232,17 +235,23 @@
musb_writeb(musb->mregs, USBC_REG_o_VEND0, 0);
if (is_host_enabled(musb)) {
- ret = sunxi_usb_phy_vbus_detect(0);
+ ret = sun4i_usb_phy_vbus_detect(glue->phy);
if (ret == 1) {
printf("A charger is plugged into the OTG: ");
return -ENODEV;
}
- ret = sunxi_usb_phy_id_detect(0);
+
+ ret = sun4i_usb_phy_id_detect(glue->phy);
if (ret == 1) {
printf("No host cable detected: ");
return -ENODEV;
}
- sunxi_usb_phy_power_on(0); /* port power on */
+
+ ret = generic_phy_power_on(glue->phy);
+ if (ret) {
+ pr_err("failed to power on USB PHY\n");
+ return ret;
+ }
}
USBC_ForceVbusValidToHigh(musb->mregs);
@@ -253,13 +262,21 @@
static void sunxi_musb_disable(struct musb *musb)
{
+ struct sunxi_glue *glue = to_sunxi_glue(musb->controller);
+ int ret;
+
pr_debug("%s():\n", __func__);
if (!enabled)
return;
- if (is_host_enabled(musb))
- sunxi_usb_phy_power_off(0); /* port power off */
+ if (is_host_enabled(musb)) {
+ ret = generic_phy_power_off(glue->phy);
+ if (ret) {
+ pr_err("failed to power off USB PHY\n");
+ return;
+ }
+ }
USBC_ForceVbusValidToLow(musb->mregs);
mdelay(200); /* Wait for the current session to timeout */
@@ -270,9 +287,16 @@
static int sunxi_musb_init(struct musb *musb)
{
struct sunxi_glue *glue = to_sunxi_glue(musb->controller);
+ int ret;
pr_debug("%s():\n", __func__);
+ ret = generic_phy_init(glue->phy);
+ if (ret) {
+ pr_err("failed to init USB PHY\n");
+ return ret;
+ }
+
musb->isr = sunxi_musb_interrupt;
setbits_le32(&glue->ccm->ahb_gate0, BIT(AHB_GATE_OFFSET_USB0));
@@ -286,8 +310,6 @@
BIT(glue->cfg->rst_bit));
#endif
- sunxi_usb_phy_init(0);
-
USBC_ConfigFIFO_Base();
USBC_EnableDpDmPullUp(musb->mregs);
USBC_EnableIdPullUp(musb->mregs);
@@ -383,6 +405,7 @@
struct usb_bus_priv *priv = dev_get_uclass_priv(dev);
struct musb_hdrc_platform_data pdata;
void *base = dev_read_addr_ptr(dev);
+ struct phy phy;
int ret;
if (!base)
@@ -396,6 +419,13 @@
if (IS_ERR(glue->ccm))
return PTR_ERR(glue->ccm);
+ ret = generic_phy_get_by_name(dev, "usb", &phy);
+ if (ret) {
+ pr_err("failed to get usb PHY\n");
+ return ret;
+ }
+
+ glue->phy = &phy;
priv->desc_before_addr = true;
memset(&pdata, 0, sizeof(pdata));
@@ -426,10 +456,18 @@
{
struct sunxi_glue *glue = dev_get_priv(dev);
struct musb_host_data *host = &glue->mdata;
+ int ret;
+
+ if (generic_phy_valid(glue->phy)) {
+ ret = generic_phy_exit(glue->phy);
+ if (ret) {
+ pr_err("failed to exit %s USB PHY\n", dev->name);
+ return ret;
+ }
+ }
musb_stop(host->host);
- sunxi_usb_phy_exit(0);
#ifdef CONFIG_SUNXI_GEN_SUN6I
clrbits_le32(&glue->ccm->ahb_reset0_cfg, BIT(AHB_GATE_OFFSET_USB0));
if (glue->cfg->rst_bit)