arm64: dts: meson: sync dt and bindings from v5.6-rc2
Sync the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
The only exception to this is the mmc pinctrl pin bias of gxl SoC family.
This is a fix which found its way to u-boot but not Linux yet.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
diff --git a/arch/arm/dts/meson-gxbb-odroidc2.dts b/arch/arm/dts/meson-gxbb-odroidc2.dts
index 54954b3..6ded279 100644
--- a/arch/arm/dts/meson-gxbb-odroidc2.dts
+++ b/arch/arm/dts/meson-gxbb-odroidc2.dts
@@ -36,8 +36,15 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
+ /*
+ * signal name from schematics: PWREN
+ */
gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
enable-active-high;
+ /*
+ * signal name from schematics: USB_POWER
+ */
+ vin-supply = <&p5v0>;
};
leds {
@@ -50,18 +57,38 @@
};
};
+ p5v0: regulator-p5v0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "P5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ hdmi_p5v0: regulator-hdmi_p5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "HDMI_P5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ /* AP2331SA-7 */
+ vin-supply = <&p5v0>;
+ };
+
tflash_vdd: regulator-tflash_vdd {
- /*
- * signal name from schematics: TFLASH_VDD_EN
- */
compatible = "regulator-fixed";
regulator-name = "TFLASH_VDD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ /*
+ * signal name from schematics: TFLASH_VDD_EN
+ */
gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
enable-active-high;
+ /* U16 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
};
tf_io: gpio-regulator-tf_io {
@@ -77,8 +104,10 @@
gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
- states = <3300000 0
- 1800000 1>;
+ states = <3300000 0>,
+ <1800000 1>;
+ /* U12/U13 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
};
vcc1v8: regulator-vcc1v8 {
@@ -86,6 +115,9 @@
regulator-name = "VCC1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ /* U18 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
};
vcc3v3: regulator-vcc3v3 {
@@ -95,6 +127,36 @@
regulator-max-microvolt = <3300000>;
};
+ vddio_ao1v8: regulator-vddio-ao1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ /* U17 RT9179GB */
+ vin-supply = <&p5v0>;
+ };
+
+ vddio_ao3v3: regulator-vddio-ao3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ /* U11 MP2161GJ-C499 */
+ vin-supply = <&p5v0>;
+ };
+
+ ddr3_1v5: regulator-ddr3_1v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "DDR3_1V5";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ /* U15 MP2161GJ-C499 */
+ vin-supply = <&p5v0>;
+ };
+
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
@@ -126,10 +188,6 @@
phy-handle = <ð_phy0>;
phy-mode = "rgmii";
- snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0 10000 1000000>;
- snps,reset-active-low;
-
amlogic,tx-delay-ns = <2>;
mdio {
@@ -140,10 +198,14 @@
eth_phy0: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_15 */
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
- eee-broken-1000t;
};
};
};
@@ -167,6 +229,7 @@
status = "okay";
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
pinctrl-names = "default";
+ hdmi-supply = <&hdmi_p5v0>;
};
&hdmi_tx_tmds_port {
@@ -187,7 +250,7 @@
pinctrl-names = "default";
};
-&pinctrl_aobus {
+&gpio_ao {
gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
"USB HUB nRESET", "USB OTG Power En",
"J7 Header Pin2", "IR In", "J7 Header Pin4",
@@ -197,7 +260,7 @@
"";
};
-&pinctrl_periphs {
+&gpio {
gpio-line-names = /* Bank GPIOZ */
"Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
"Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
@@ -256,11 +319,14 @@
bus-width = <4>;
cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-ddr50;
max-frequency = <100000000>;
disable-wp;
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&tflash_vdd>;
vqmmc-supply = <&tf_io>;
@@ -274,7 +340,7 @@
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
- max-frequency = <100000000>;
+ max-frequency = <200000000>;
non-removable;
disable-wp;
cap-mmc-highspeed;
@@ -293,7 +359,7 @@
};
&usb0_phy {
- status = "okay";
+ status = "disabled";
phy-supply = <&usb_otg_pwr>;
};
@@ -303,7 +369,7 @@
};
&usb0 {
- status = "okay";
+ status = "disabled";
};
&usb1 {