Merge git://git.denx.de/u-boot-dm
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 4528a8f..6b9d6fb 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -353,6 +353,26 @@
keystone-k2e-evm.dtb \
keystone-k2g-evm.dtb
+dtb-$(CONFIG_TARGET_AT91SAM9263EK) += at91sam9263ek.dtb
+
+dtb-$(CONFIG_TARGET_AT91SAM9RLEK) += at91sam9rlek.dtb
+
+dtb-$(CONFIG_TARGET_AT91SAM9260EK) += \
+ at91sam9260ek.dtb \
+ at91sam9g20ek.dtb \
+ at91sam9g20ek_2mmc.dtb
+
+dtb-$(CONFIG_TARGET_AT91SAM9M10G45EK) += at91sam9m10g45ek.dtb
+
+dtb-$(CONFIG_TARGET_AT91SAM9X5EK) += \
+ at91sam9g15ek.dtb \
+ at91sam9g25ek.dtb \
+ at91sam9g35ek.dtb \
+ at91sam9x25ek.dtb \
+ at91sam9x35ek.dtb
+
+dtb-$(CONFIG_TARGET_AT91SAM9N12EK) += at91sam9n12ek.dtb
+
dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
at91-sama5d2_xplained.dtb
diff --git a/arch/arm/dts/at91-sama5d2_xplained.dts b/arch/arm/dts/at91-sama5d2_xplained.dts
index 3709437..3e624f1 100644
--- a/arch/arm/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/dts/at91-sama5d2_xplained.dts
@@ -7,6 +7,7 @@
compatible = "atmel,sama5d2-xplained", "atmel,sama5d2", "atmel,sama5";
chosen {
+ u-boot,dm-pre-reloc;
stdout-path = &uart1;
};
@@ -28,6 +29,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_cmd_dat_default &pinctrl_sdmmc0_ck_cd_default>;
status = "okay";
+ u-boot,dm-pre-reloc;
};
sdmmc1: sdio-host@b0000000 {
@@ -35,6 +37,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc1_cmd_dat_default &pinctrl_sdmmc1_ck_cd_default>;
status = "okay"; /* conflict with qspi0 */
+ u-boot,dm-pre-reloc;
};
apb {
@@ -67,11 +70,13 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0_default>;
status = "okay";
+ u-boot,dm-pre-reloc;
spi_flash@0 {
compatible = "spi-flash";
reg = <0>;
spi-max-frequency = <50000000>;
+ u-boot,dm-pre-reloc;
};
};
@@ -90,6 +95,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
status = "okay";
+ u-boot,dm-pre-reloc;
};
i2c1: i2c@fc028000 {
@@ -146,6 +152,7 @@
<PIN_PA8__SDMMC0_DAT6>,
<PIN_PA9__SDMMC0_DAT7>;
bias-pull-up;
+ u-boot,dm-pre-reloc;
};
pinctrl_sdmmc0_ck_cd_default: sdmmc0_ck_cd_default {
@@ -154,6 +161,7 @@
<PIN_PA11__SDMMC0_VDDSEL>,
<PIN_PA13__SDMMC0_CD>;
bias-disable;
+ u-boot,dm-pre-reloc;
};
pinctrl_sdmmc1_cmd_dat_default: sdmmc1_cmd_dat_default {
@@ -163,12 +171,14 @@
<PIN_PA20__SDMMC1_DAT2>,
<PIN_PA21__SDMMC1_DAT3>;
bias-pull-up;
+ u-boot,dm-pre-reloc;
};
pinctrl_sdmmc1_ck_cd_default: sdmmc1_ck_cd_default {
pinmux = <PIN_PA22__SDMMC1_CK>,
<PIN_PA30__SDMMC1_CD>;
bias-disable;
+ u-boot,dm-pre-reloc;
};
pinctrl_spi0_default: spi0_default {
@@ -176,12 +186,14 @@
<PIN_PA15__SPI0_MOSI>,
<PIN_PA16__SPI0_MISO>;
bias-disable;
+ u-boot,dm-pre-reloc;
};
pinctrl_uart1_default: uart1_default {
pinmux = <PIN_PD2__URXD1>,
<PIN_PD3__UTXD1>;
bias-disable;
+ u-boot,dm-pre-reloc;
};
pinctrl_usb_default: usb_default {
diff --git a/arch/arm/dts/at91sam9260.dtsi b/arch/arm/dts/at91sam9260.dtsi
index d4884dd..0f25e33 100644
--- a/arch/arm/dts/at91sam9260.dtsi
+++ b/arch/arm/dts/at91sam9260.dtsi
@@ -79,12 +79,14 @@
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ u-boot,dm-pre-reloc;
apb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ u-boot,dm-pre-reloc;
aic: interrupt-controller@fffff000 {
#interrupt-cells = <3>;
@@ -107,6 +109,7 @@
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
+ u-boot,dm-pre-reloc;
main_osc: main_osc {
compatible = "atmel,at91rm9200-clk-main-osc";
@@ -134,7 +137,7 @@
clocks = <&slow_rc_osc>, <&slow_xtal>;
};
- plla: pllack {
+ plla: pllack@0 {
compatible = "atmel,at91rm9200-clk-pll";
#clock-cells = <0>;
interrupts-extended = <&pmc AT91_PMC_LOCKA>;
@@ -146,7 +149,7 @@
<150000000 240000000 2 1>;
};
- pllb: pllbck {
+ pllb: pllbck@1 {
compatible = "atmel,at91rm9200-clk-pll";
#clock-cells = <0>;
interrupts-extended = <&pmc AT91_PMC_LOCKB>;
@@ -164,6 +167,7 @@
clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
atmel,clk-output-range = <0 105000000>;
atmel,clk-divisors = <1 2 4 0>;
+ u-boot,dm-pre-reloc;
};
usb: usbck {
@@ -180,13 +184,13 @@
interrupt-parent = <&pmc>;
clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
- prog0: prog0 {
+ prog0: prog@0 {
#clock-cells = <0>;
reg = <0>;
interrupts = <AT91_PMC_PCKRDY(0)>;
};
- prog1: prog1 {
+ prog1: prog@1 {
#clock-cells = <0>;
reg = <1>;
interrupts = <AT91_PMC_PCKRDY(1)>;
@@ -198,25 +202,25 @@
#address-cells = <1>;
#size-cells = <0>;
- uhpck: uhpck {
+ uhpck: uhpck@6 {
#clock-cells = <0>;
reg = <6>;
clocks = <&usb>;
};
- udpck: udpck {
+ udpck: udpck@7 {
#clock-cells = <0>;
reg = <7>;
clocks = <&usb>;
};
- pck0: pck0 {
+ pck0: pck0@8 {
#clock-cells = <0>;
reg = <8>;
clocks = <&prog0>;
};
- pck1: pck1 {
+ pck1: pck1@9 {
#clock-cells = <0>;
reg = <9>;
clocks = <&prog1>;
@@ -228,128 +232,132 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&mck>;
+ u-boot,dm-pre-reloc;
- pioA_clk: pioA_clk {
+ pioA_clk: pioA_clk@2 {
#clock-cells = <0>;
reg = <2>;
+ u-boot,dm-pre-reloc;
};
- pioB_clk: pioB_clk {
+ pioB_clk: pioB_clk@3 {
#clock-cells = <0>;
reg = <3>;
+ u-boot,dm-pre-reloc;
};
- pioC_clk: pioC_clk {
+ pioC_clk: pioC_clk@4 {
#clock-cells = <0>;
reg = <4>;
+ u-boot,dm-pre-reloc;
};
- adc_clk: adc_clk {
+ adc_clk: adc_clk@5 {
#clock-cells = <0>;
reg = <5>;
};
- usart0_clk: usart0_clk {
+ usart0_clk: usart0_clk@6 {
#clock-cells = <0>;
reg = <6>;
};
- usart1_clk: usart1_clk {
+ usart1_clk: usart1_clk@7 {
#clock-cells = <0>;
reg = <7>;
};
- usart2_clk: usart2_clk {
+ usart2_clk: usart2_clk@8 {
#clock-cells = <0>;
reg = <8>;
};
- mci0_clk: mci0_clk {
+ mci0_clk: mci0_clk@9 {
#clock-cells = <0>;
reg = <9>;
};
- udc_clk: udc_clk {
+ udc_clk: udc_clk@10 {
#clock-cells = <0>;
reg = <10>;
};
- twi0_clk: twi0_clk {
+ twi0_clk: twi0_clk@11 {
reg = <11>;
#clock-cells = <0>;
};
- spi0_clk: spi0_clk {
+ spi0_clk: spi0_clk@12 {
#clock-cells = <0>;
reg = <12>;
};
- spi1_clk: spi1_clk {
+ spi1_clk: spi1_clk@13 {
#clock-cells = <0>;
reg = <13>;
};
- ssc0_clk: ssc0_clk {
+ ssc0_clk: ssc0_clk@14 {
#clock-cells = <0>;
reg = <14>;
};
- tc0_clk: tc0_clk {
+ tc0_clk: tc0_clk@17 {
#clock-cells = <0>;
reg = <17>;
};
- tc1_clk: tc1_clk {
+ tc1_clk: tc1_clk@18 {
#clock-cells = <0>;
reg = <18>;
};
- tc2_clk: tc2_clk {
+ tc2_clk: tc2_clk@19 {
#clock-cells = <0>;
reg = <19>;
};
- ohci_clk: ohci_clk {
+ ohci_clk: ohci_clk@20 {
#clock-cells = <0>;
reg = <20>;
};
- macb0_clk: macb0_clk {
+ macb0_clk: macb0_clk@21 {
#clock-cells = <0>;
reg = <21>;
};
- isi_clk: isi_clk {
+ isi_clk: isi_clk@22 {
#clock-cells = <0>;
reg = <22>;
};
- usart3_clk: usart3_clk {
+ usart3_clk: usart3_clk@23 {
#clock-cells = <0>;
reg = <23>;
};
- uart0_clk: uart0_clk {
+ uart0_clk: uart0_clk@24 {
#clock-cells = <0>;
reg = <24>;
};
- uart1_clk: uart1_clk {
+ uart1_clk: uart1_clk@25 {
#clock-cells = <0>;
reg = <25>;
};
- tc3_clk: tc3_clk {
+ tc3_clk: tc3_clk@26 {
#clock-cells = <0>;
reg = <26>;
};
- tc4_clk: tc4_clk {
+ tc4_clk: tc4_clk@27 {
#clock-cells = <0>;
reg = <27>;
};
- tc5_clk: tc5_clk {
+ tc5_clk: tc5_clk@28 {
#clock-cells = <0>;
reg = <28>;
};
@@ -395,11 +403,51 @@
clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
};
+ pioA: gpio@fffff400 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioA_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioB: gpio@fffff600 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioB_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioC: gpio@fffff800 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioC_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
pinctrl@fffff400 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x600>;
+ reg = <0xfffff400 0x200 /* pioA */
+ 0xfffff600 0x200 /* pioB */
+ 0xfffff800 0x200 /* pioC */
+ >;
atmel,mux-mask = <
/* A B */
@@ -407,9 +455,11 @@
0xffffffff 0x7fff3ccf /* pioB */
0xffffffff 0x007fffff /* pioC */
>;
+ u-boot,dm-pre-reloc;
/* shared pinctrl settings */
dbgu {
+ u-boot,dm-pre-reloc;
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB14 periph A */
@@ -719,39 +769,6 @@
atmel,pins = <AT91_PIOB 19 AT91_PERIPH_B AT91_PINCTRL_NONE>;
};
};
-
- pioA: gpio@fffff400 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff400 0x200>;
- interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioA_clk>;
- };
-
- pioB: gpio@fffff600 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff600 0x200>;
- interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioB_clk>;
- };
-
- pioC: gpio@fffff800 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff800 0x200>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioC_clk>;
- };
};
dbgu: serial@fffff200 {
diff --git a/arch/arm/dts/at91sam9260ek.dts b/arch/arm/dts/at91sam9260ek.dts
new file mode 100644
index 0000000..086c8ea
--- /dev/null
+++ b/arch/arm/dts/at91sam9260ek.dts
@@ -0,0 +1,215 @@
+/*
+ * Device Tree file for Atmel at91sam9260 Evaluation Kit
+ *
+ * Copyright (C) 2016 Atmel,
+ * 2016 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "at91sam9260.dtsi"
+
+/ {
+ model = "Atmel at91sam9260ek";
+ compatible = "atmel,at91sam9260ek", "atmel,at91sam9260", "atmel,at91sam9";
+
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &dbgu;
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <18432000>;
+ };
+ };
+
+ ahb {
+ apb {
+ usb1: gadget@fffa4000 {
+ atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ mmc0: mmc@fffa8000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0_slot1
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot1_cmd_dat0
+ &pinctrl_mmc0_slot1_dat1_3>;
+ status = "okay";
+ slot@1 {
+ reg = <1>;
+ bus-width = <4>;
+ cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ usart0: serial@fffb0000 {
+ pinctrl-0 =
+ <&pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts
+ &pinctrl_usart0_dtr_dsr
+ &pinctrl_usart0_dcd
+ &pinctrl_usart0_ri>;
+ status = "okay";
+ };
+
+ usart1: serial@fffb4000 {
+ status = "okay";
+ };
+
+ ssc0: ssc@fffbc000 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_ssc0_tx>;
+ };
+
+ macb0: ethernet@fffc4000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ spi0: spi@fffc8000 {
+ cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <50000000>;
+ reg = <1>;
+ };
+ };
+
+ dbgu: serial@fffff200 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ board {
+ pinctrl_board_mmc0_slot1: mmc0_slot1-board {
+ atmel,pins =
+ <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ };
+ };
+
+ shdwc@fffffd10 {
+ atmel,wakeup-counter = <10>;
+ atmel,wakeup-rtt-timer;
+ };
+
+ rtc@fffffd20 {
+ atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+ status = "okay";
+ };
+
+ watchdog@fffffd40 {
+ status = "okay";
+ };
+
+ gpbr: syscon@fffffd50 {
+ status = "okay";
+ };
+ };
+
+ usb0: ohci@00500000 {
+ num-ports = <2>;
+ status = "okay";
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ btn3 {
+ label = "Button 3";
+ gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
+ linux,code = <0x103>;
+ wakeup-source;
+ };
+
+ btn4 {
+ label = "Button 4";
+ gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ wakeup-source;
+ };
+ };
+
+ i2c-gpio-0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ 24c512@50 {
+ compatible = "24c512";
+ reg = <0x50>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ds1 {
+ label = "ds1";
+ gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds5 {
+ label = "ds5";
+ gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9263.dtsi b/arch/arm/dts/at91sam9263.dtsi
index 9344642..e899fd3 100644
--- a/arch/arm/dts/at91sam9263.dtsi
+++ b/arch/arm/dts/at91sam9263.dtsi
@@ -77,12 +77,14 @@
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ u-boot,dm-pre-reloc;
apb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ u-boot,dm-pre-reloc;
aic: interrupt-controller@fffff000 {
#interrupt-cells = <3>;
@@ -100,6 +102,7 @@
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
+ u-boot,dm-pre-reloc;
main_osc: main_osc {
compatible = "atmel,at91rm9200-clk-main-osc";
@@ -114,7 +117,7 @@
clocks = <&main_osc>;
};
- plla: pllack {
+ plla: pllack@0 {
compatible = "atmel,at91rm9200-clk-pll";
#clock-cells = <0>;
interrupts-extended = <&pmc AT91_PMC_LOCKA>;
@@ -126,7 +129,7 @@
<190000000 240000000 2 1>;
};
- pllb: pllbck {
+ pllb: pllbck@1 {
compatible = "atmel,at91rm9200-clk-pll";
#clock-cells = <0>;
interrupts-extended = <&pmc AT91_PMC_LOCKB>;
@@ -145,6 +148,7 @@
clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
atmel,clk-output-range = <0 120000000>;
atmel,clk-divisors = <1 2 4 0>;
+ u-boot,dm-pre-reloc;
};
usb: usbck {
@@ -161,25 +165,25 @@
interrupt-parent = <&pmc>;
clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
- prog0: prog0 {
+ prog0: prog@0 {
#clock-cells = <0>;
reg = <0>;
interrupts = <AT91_PMC_PCKRDY(0)>;
};
- prog1: prog1 {
+ prog1: prog@1 {
#clock-cells = <0>;
reg = <1>;
interrupts = <AT91_PMC_PCKRDY(1)>;
};
- prog2: prog2 {
+ prog2: prog@2 {
#clock-cells = <0>;
reg = <2>;
interrupts = <AT91_PMC_PCKRDY(2)>;
};
- prog3: prog3 {
+ prog3: prog@3 {
#clock-cells = <0>;
reg = <3>;
interrupts = <AT91_PMC_PCKRDY(3)>;
@@ -191,37 +195,37 @@
#address-cells = <1>;
#size-cells = <0>;
- uhpck: uhpck {
+ uhpck: uhpck@6 {
#clock-cells = <0>;
reg = <6>;
clocks = <&usb>;
};
- udpck: udpck {
+ udpck: udpck@7 {
#clock-cells = <0>;
reg = <7>;
clocks = <&usb>;
};
- pck0: pck0 {
+ pck0: pck0@8 {
#clock-cells = <0>;
reg = <8>;
clocks = <&prog0>;
};
- pck1: pck1 {
+ pck1: pck1@9 {
#clock-cells = <0>;
reg = <9>;
clocks = <&prog1>;
};
- pck2: pck2 {
+ pck2: pck2@10 {
#clock-cells = <0>;
reg = <10>;
clocks = <&prog2>;
};
- pck3: pck3 {
+ pck3: pck3@11 {
#clock-cells = <0>;
reg = <11>;
clocks = <&prog3>;
@@ -233,123 +237,127 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&mck>;
+ u-boot,dm-pre-reloc;
- pioA_clk: pioA_clk {
+ pioA_clk: pioA_clk@2 {
#clock-cells = <0>;
reg = <2>;
+ u-boot,dm-pre-reloc;
};
- pioB_clk: pioB_clk {
+ pioB_clk: pioB_clk@3 {
#clock-cells = <0>;
reg = <3>;
+ u-boot,dm-pre-reloc;
};
- pioCDE_clk: pioCDE_clk {
+ pioCDE_clk: pioCDE_clk@4 {
#clock-cells = <0>;
reg = <4>;
+ u-boot,dm-pre-reloc;
};
- usart0_clk: usart0_clk {
+ usart0_clk: usart0_clk@7 {
#clock-cells = <0>;
reg = <7>;
};
- usart1_clk: usart1_clk {
+ usart1_clk: usart1_clk@8 {
#clock-cells = <0>;
reg = <8>;
};
- usart2_clk: usart2_clk {
+ usart2_clk: usart2_clk@9 {
#clock-cells = <0>;
reg = <9>;
};
- mci0_clk: mci0_clk {
+ mci0_clk: mci0_clk@10 {
#clock-cells = <0>;
reg = <10>;
};
- mci1_clk: mci1_clk {
+ mci1_clk: mci1_clk@11 {
#clock-cells = <0>;
reg = <11>;
};
- can_clk: can_clk {
+ can_clk: can_clk@12 {
#clock-cells = <0>;
reg = <12>;
};
- twi0_clk: twi0_clk {
+ twi0_clk: twi0_clk@13 {
#clock-cells = <0>;
reg = <13>;
};
- spi0_clk: spi0_clk {
+ spi0_clk: spi0_clk@14 {
#clock-cells = <0>;
reg = <14>;
};
- spi1_clk: spi1_clk {
+ spi1_clk: spi1_clk@15 {
#clock-cells = <0>;
reg = <15>;
};
- ssc0_clk: ssc0_clk {
+ ssc0_clk: ssc0_clk@16 {
#clock-cells = <0>;
reg = <16>;
};
- ssc1_clk: ssc1_clk {
+ ssc1_clk: ssc1_clk@17 {
#clock-cells = <0>;
reg = <17>;
};
- ac97_clk: ac97_clk {
+ ac97_clk: ac97_clk@18 {
#clock-cells = <0>;
reg = <18>;
};
- tcb_clk: tcb_clk {
+ tcb_clk: tcb_clk@19 {
#clock-cells = <0>;
reg = <19>;
};
- pwm_clk: pwm_clk {
+ pwm_clk: pwm_clk@20 {
#clock-cells = <0>;
reg = <20>;
};
- macb0_clk: macb0_clk {
+ macb0_clk: macb0_clk@21 {
#clock-cells = <0>;
reg = <21>;
};
- g2de_clk: g2de_clk {
+ g2de_clk: g2de_clk@23 {
#clock-cells = <0>;
reg = <23>;
};
- udc_clk: udc_clk {
+ udc_clk: udc_clk@24 {
#clock-cells = <0>;
reg = <24>;
};
- isi_clk: isi_clk {
+ isi_clk: isi_clk@25 {
#clock-cells = <0>;
reg = <25>;
};
- lcd_clk: lcd_clk {
+ lcd_clk: lcd_clk@26 {
#clock-cells = <0>;
reg = <26>;
};
- dma_clk: dma_clk {
+ dma_clk: dma_clk@27 {
#clock-cells = <0>;
reg = <27>;
};
- ohci_clk: ohci_clk {
+ ohci_clk: ohci_clk@29 {
#clock-cells = <0>;
reg = <29>;
};
@@ -398,6 +406,12 @@
#size-cells = <1>;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff200 0xfffff200 0xa00>;
+ reg = <0xfffff200 0x200
+ 0xfffff400 0x200
+ 0xfffff600 0x200
+ 0xfffff800 0x200
+ 0xfffffa00 0x200
+ >;
atmel,mux-mask = <
/* A B */
@@ -412,8 +426,8 @@
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
- <AT91_PIOC 30 AT91_PERIPH_A AT91_PINCTRL_NONE /* PC30 periph A */
- AT91_PIOC 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PC31 periph with pullup */
+ <AT91_PIOC 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOC 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;
};
};
@@ -707,60 +721,66 @@
};
};
- pioA: gpio@fffff200 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff200 0x200>;
- interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioA_clk>;
- };
+ };
- pioB: gpio@fffff400 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff400 0x200>;
- interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioB_clk>;
- };
+ pioA: gpio@fffff200 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff200 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioA_clk>;
+ u-boot,dm-pre-reloc;
+ };
- pioC: gpio@fffff600 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff600 0x200>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioCDE_clk>;
- };
+ pioB: gpio@fffff400 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioB_clk>;
+ u-boot,dm-pre-reloc;
+ };
- pioD: gpio@fffff800 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff800 0x200>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioCDE_clk>;
- };
+ pioC: gpio@fffff600 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioCDE_clk>;
+ u-boot,dm-pre-reloc;
+ };
- pioE: gpio@fffffa00 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffffa00 0x200>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioCDE_clk>;
- };
+ pioD: gpio@fffff800 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioCDE_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioE: gpio@fffffa00 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioCDE_clk>;
+ u-boot,dm-pre-reloc;
};
dbgu: serial@ffffee00 {
@@ -1019,7 +1039,7 @@
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
&pioB 5 GPIO_ACTIVE_HIGH /* scl */
diff --git a/arch/arm/dts/at91sam9263ek.dts b/arch/arm/dts/at91sam9263ek.dts
new file mode 100644
index 0000000..8cd7fad
--- /dev/null
+++ b/arch/arm/dts/at91sam9263ek.dts
@@ -0,0 +1,229 @@
+/*
+ * at91sam9263ek.dts - Device Tree file for Atmel at91sam9263 reference board
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2 only
+ */
+/dts-v1/;
+#include "at91sam9263.dtsi"
+
+/ {
+ model = "Atmel at91sam9263ek";
+ compatible = "atmel,at91sam9263ek", "atmel,at91sam9263", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+ stdout-path = "serial0:115200n8";
+ u-boot,dm-pre-reloc;
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <16367660>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial@ffffee00 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ usart0: serial@fff8c000 {
+ pinctrl-0 = <
+ &pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts>;
+ status = "okay";
+ };
+
+ macb0: ethernet@fffbc000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ usb1: gadget@fff78000 {
+ atmel,vbus-gpio = <&pioA 25 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ mmc0: mmc@fff80000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot0_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioE 18 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&pioE 19 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ pinctrl@fffff200 {
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOE 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* PE18 gpio CD pin pull up and deglitch */
+ AT91_PIOE 19 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PE19 gpio WP pin pull up */
+ };
+ };
+ };
+
+ spi0: spi@fffa4000 {
+ status = "okay";
+ cs-gpios = <&pioA 5 0>, <0>, <0>, <0>;
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ watchdog@fffffd40 {
+ status = "okay";
+ };
+ };
+
+ fb0: fb@0x00700000 {
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <1>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <4965000>;
+ hactive = <240>;
+ vactive = <320>;
+ hback-porch = <1>;
+ hfront-porch = <33>;
+ vback-porch = <1>;
+ vfront-porch = <0>;
+ hsync-len = <5>;
+ vsync-len = <1>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt = <1>;
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ barebox@20000 {
+ label = "barebox";
+ reg = <0x20000 0x40000>;
+ };
+
+ bareboxenv@60000 {
+ label = "bareboxenv";
+ reg = <0x60000 0x20000>;
+ };
+
+ bareboxenv2@80000 {
+ label = "bareboxenv2";
+ reg = <0x80000 0x20000>;
+ };
+
+ oftree@80000 {
+ label = "oftree";
+ reg = <0xa0000 0x20000>;
+ };
+
+ kernel@a0000 {
+ label = "kernel";
+ reg = <0xc0000 0x400000>;
+ };
+
+ rootfs@4a0000 {
+ label = "rootfs";
+ reg = <0x4c0000 0x7800000>;
+ };
+
+ data@7ca0000 {
+ label = "data";
+ reg = <0x7cc0000 0x8340000>;
+ };
+ };
+
+ usb0: ohci@00a00000 {
+ num-ports = <2>;
+ status = "okay";
+ atmel,vbus-gpio = <&pioA 24 GPIO_ACTIVE_HIGH
+ &pioA 21 GPIO_ACTIVE_HIGH
+ >;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d3 {
+ label = "d3";
+ gpios = <&pioB 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ d2 {
+ label = "d2";
+ gpios = <&pioC 29 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "nand-disk";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ left_click {
+ label = "left_click";
+ gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
+ linux,code = <272>;
+ wakeup-source;
+ };
+
+ right_click {
+ label = "right_click";
+ gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
+ linux,code = <273>;
+ wakeup-source;
+ };
+ };
+
+ i2c-gpio-0 {
+ status = "okay";
+
+ 24c512@50 {
+ compatible = "24c512";
+ reg = <0x50>;
+ pagesize = <128>;
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g15.dtsi b/arch/arm/dts/at91sam9g15.dtsi
new file mode 100644
index 0000000..27de7dc
--- /dev/null
+++ b/arch/arm/dts/at91sam9g15.dtsi
@@ -0,0 +1,29 @@
+/*
+ * at91sam9g15.dtsi - Device Tree Include file for AT91SAM9G15 SoC
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include "at91sam9x5.dtsi"
+#include "at91sam9x5_lcd.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9G15 SoC";
+ compatible = "atmel,at91sam9g15", "atmel,at91sam9x5";
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe0399f 0x00000000 /* pioA */
+ 0x00040000 0x00047e3f 0x00000000 /* pioB */
+ 0xfdffffff 0x00000000 0xb83fffff /* pioC */
+ 0x003fffff 0x003f8000 0x00000000 /* pioD */
+ >;
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g15ek.dts b/arch/arm/dts/at91sam9g15ek.dts
new file mode 100644
index 0000000..9fae925
--- /dev/null
+++ b/arch/arm/dts/at91sam9g15ek.dts
@@ -0,0 +1,26 @@
+/*
+ * at91sam9g15ek.dts - Device Tree file for AT91SAM9G15-EK board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g15.dtsi"
+#include "at91sam9x5dm.dtsi"
+#include "at91sam9x5ek.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9G15-EK";
+ compatible = "atmel,at91sam9g15ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+ ahb {
+ apb {
+ hlcdc: hlcdc@f8038000 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g20.dtsi b/arch/arm/dts/at91sam9g20.dtsi
index f593016..e88d73c 100644
--- a/arch/arm/dts/at91sam9g20.dtsi
+++ b/arch/arm/dts/at91sam9g20.dtsi
@@ -40,7 +40,7 @@
};
pmc: pmc@fffffc00 {
- plla: pllack {
+ plla: pllack@0 {
atmel,clk-input-range = <2000000 32000000>;
atmel,pll-clk-output-ranges = <745000000 800000000 0 0>,
<695000000 750000000 1 0>,
@@ -52,7 +52,7 @@
<400000000 450000000 3 1>;
};
- pllb: pllbck {
+ pllb: pllbck@1 {
compatible = "atmel,at91sam9g20-clk-pllb";
atmel,clk-input-range = <2000000 32000000>;
atmel,pll-clk-output-ranges = <30000000 100000000 0 0>;
diff --git a/arch/arm/dts/at91sam9g20ek.dts b/arch/arm/dts/at91sam9g20ek.dts
new file mode 100644
index 0000000..bbfd753
--- /dev/null
+++ b/arch/arm/dts/at91sam9g20ek.dts
@@ -0,0 +1,29 @@
+/*
+ * at91sam9g20ek.dts - Device Tree file for Atmel at91sam9g20ek board
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+#include "at91sam9g20ek_common.dtsi"
+
+/ {
+ model = "Atmel at91sam9g20ek";
+ compatible = "atmel,at91sam9g20ek", "atmel,at91sam9g20", "atmel,at91sam9";
+
+ leds {
+ compatible = "gpio-leds";
+
+ ds1 {
+ label = "ds1";
+ gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds5 {
+ label = "ds5";
+ gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g20ek_2mmc.dts b/arch/arm/dts/at91sam9g20ek_2mmc.dts
new file mode 100644
index 0000000..7ea83b6
--- /dev/null
+++ b/arch/arm/dts/at91sam9g20ek_2mmc.dts
@@ -0,0 +1,56 @@
+/*
+ * at91sam9g20ek_2mmc.dts - Device Tree file for Atmel at91sam9g20ek 2 MMC board
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+#include "at91sam9g20ek_common.dtsi"
+
+/ {
+ model = "Atmel at91sam9g20ek 2 mmc";
+ compatible = "atmel,at91sam9g20ek_2mmc", "atmel,at91sam9g20", "atmel,at91sam9";
+
+ ahb {
+ apb{
+ mmc0: mmc@fffa8000 {
+ /* clk already mux wuth slot0 */
+ pinctrl-0 = <
+ &pinctrl_board_mmc0_slot0
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot0_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ pinctrl@fffff400 {
+ mmc0_slot0 {
+ pinctrl_board_mmc0_slot0: mmc0_slot0-board {
+ atmel,pins =
+ <AT91_PIOC 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC2 gpio CD pin pull up and deglitch */
+ };
+ };
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ds1 {
+ label = "ds1";
+ gpios = <&pioB 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds5 {
+ label = "ds5";
+ gpios = <&pioB 8 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g20ek_common.dtsi b/arch/arm/dts/at91sam9g20ek_common.dtsi
new file mode 100644
index 0000000..65ae099
--- /dev/null
+++ b/arch/arm/dts/at91sam9g20ek_common.dtsi
@@ -0,0 +1,227 @@
+/*
+ * at91sam9g20ek_common.dtsi - Device Tree file for Atmel at91sam9g20ek board
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+#include "at91sam9g20.dtsi"
+
+/ {
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &dbgu;
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <18432000>;
+ };
+ };
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ board {
+ pinctrl_pck0_as_mck: pck0_as_mck {
+ atmel,pins =
+ <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC1 periph B */
+ };
+
+ };
+
+ mmc0_slot1 {
+ pinctrl_board_mmc0_slot1: mmc0_slot1-board {
+ atmel,pins =
+ <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC9 gpio CD pin pull up and deglitch */
+ };
+ };
+ };
+
+ dbgu: serial@fffff200 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ usart0: serial@fffb0000 {
+ pinctrl-0 =
+ <&pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts
+ &pinctrl_usart0_dtr_dsr
+ &pinctrl_usart0_dcd
+ &pinctrl_usart0_ri>;
+ status = "okay";
+ };
+
+ usart1: serial@fffb4000 {
+ status = "okay";
+ };
+
+ macb0: ethernet@fffc4000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ usb1: gadget@fffa4000 {
+ atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ mmc0: mmc@fffa8000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0_slot1
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot1_cmd_dat0
+ &pinctrl_mmc0_slot1_dat1_3>;
+ status = "okay";
+ slot@1 {
+ reg = <1>;
+ bus-width = <4>;
+ cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ ssc0: ssc@fffbc000 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_ssc0_tx>;
+ };
+
+ spi0: spi@fffc8000 {
+ cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <50000000>;
+ reg = <1>;
+ };
+ };
+
+ shdwc@fffffd10 {
+ atmel,wakeup-counter = <10>;
+ atmel,wakeup-rtt-timer;
+ };
+
+ rtc@fffffd20 {
+ atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+ status = "okay";
+ };
+
+ watchdog@fffffd40 {
+ status = "okay";
+ };
+
+ gpbr: syscon@fffffd50 {
+ status = "okay";
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ barebox@20000 {
+ label = "barebox";
+ reg = <0x20000 0x40000>;
+ };
+
+ bareboxenv@60000 {
+ label = "bareboxenv";
+ reg = <0x60000 0x20000>;
+ };
+
+ bareboxenv2@80000 {
+ label = "bareboxenv2";
+ reg = <0x80000 0x20000>;
+ };
+
+ oftree@80000 {
+ label = "oftree";
+ reg = <0xa0000 0x20000>;
+ };
+
+ kernel@a0000 {
+ label = "kernel";
+ reg = <0xc0000 0x400000>;
+ };
+
+ rootfs@4a0000 {
+ label = "rootfs";
+ reg = <0x4c0000 0x7800000>;
+ };
+
+ data@7ca0000 {
+ label = "data";
+ reg = <0x7cc0000 0x8340000>;
+ };
+ };
+
+ usb0: ohci@00500000 {
+ num-ports = <2>;
+ status = "okay";
+ };
+ };
+
+ i2c-gpio-0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ 24c512@50 {
+ compatible = "24c512";
+ reg = <0x50>;
+ };
+
+ wm8731: wm8731@1b {
+ compatible = "wm8731";
+ reg = <0x1b>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ btn3 {
+ label = "Button 3";
+ gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
+ linux,code = <0x103>;
+ wakeup-source;
+ };
+
+ btn4 {
+ label = "Button 4";
+ gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ wakeup-source;
+ };
+ };
+
+ sound {
+ compatible = "atmel,at91sam9g20ek-wm8731-audio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_mck>;
+
+ atmel,model = "wm8731 @ AT91SAMG20EK";
+
+ atmel,audio-routing =
+ "Ext Spk", "LHPOUT",
+ "Int Mic", "MICIN";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8731>;
+ };
+};
diff --git a/arch/arm/dts/at91sam9g25.dtsi b/arch/arm/dts/at91sam9g25.dtsi
new file mode 100644
index 0000000..a7da0dd
--- /dev/null
+++ b/arch/arm/dts/at91sam9g25.dtsi
@@ -0,0 +1,31 @@
+/*
+ * at91sam9g25.dtsi - Device Tree Include file for AT91SAM9G25 SoC
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include "at91sam9x5.dtsi"
+#include "at91sam9x5_isi.dtsi"
+#include "at91sam9x5_usart3.dtsi"
+#include "at91sam9x5_macb0.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9G25 SoC";
+ compatible = "atmel,at91sam9g25", "atmel,at91sam9x5";
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe0399f 0xc000001c /* pioA */
+ 0x0007ffff 0x8000fe3f 0x00000000 /* pioB */
+ 0x80000000 0x07c0ffff 0xb83fffff /* pioC */
+ 0x003fffff 0x003f8000 0x00000000 /* pioD */
+ >;
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g25ek.dts b/arch/arm/dts/at91sam9g25ek.dts
new file mode 100644
index 0000000..91a7177
--- /dev/null
+++ b/arch/arm/dts/at91sam9g25ek.dts
@@ -0,0 +1,69 @@
+/*
+ * at91sam9g25ek.dts - Device Tree file for AT91SAM9G25-EK board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+#include "at91sam9x5ek.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9G25-EK";
+ compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+ ahb {
+ apb {
+ spi0: spi@f0000000 {
+ status = "disabled";
+ };
+
+ mmc1: mmc@f000c000 {
+ status = "disabled";
+ };
+
+ i2c0: i2c@f8010000 {
+ ov2640: camera@0x30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
+ clocks = <&pck0>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck0>;
+ assigned-clock-rates = <25000000>;
+ status = "okay";
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
+
+ macb0: ethernet@f802c000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ isi: isi@f8048000 {
+ status = "okay";
+ port {
+ isi_0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ vsync-active = <1>;
+ hsync-active = <1>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g35.dtsi b/arch/arm/dts/at91sam9g35.dtsi
new file mode 100644
index 0000000..ff41158
--- /dev/null
+++ b/arch/arm/dts/at91sam9g35.dtsi
@@ -0,0 +1,30 @@
+/*
+ * at91sam9g35.dtsi - Device Tree Include file for AT91SAM9G35 SoC
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include "at91sam9x5.dtsi"
+#include "at91sam9x5_lcd.dtsi"
+#include "at91sam9x5_macb0.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9G35 SoC";
+ compatible = "atmel,at91sam9g35", "atmel,at91sam9x5";
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe0399f 0xc000000c /* pioA */
+ 0x000406ff 0x00047e3f 0x00000000 /* pioB */
+ 0xfdffffff 0x00000000 0xb83fffff /* pioC */
+ 0x003fffff 0x003f8000 0x00000000 /* pioD */
+ >;
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g35ek.dts b/arch/arm/dts/at91sam9g35ek.dts
new file mode 100644
index 0000000..0cc084e
--- /dev/null
+++ b/arch/arm/dts/at91sam9g35ek.dts
@@ -0,0 +1,31 @@
+/*
+ * at91sam9g35ek.dts - Device Tree file for AT91SAM9G35-EK board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g35.dtsi"
+#include "at91sam9x5dm.dtsi"
+#include "at91sam9x5ek.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9G35-EK";
+ compatible = "atmel,at91sam9g35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+ ahb {
+ apb {
+ macb0: ethernet@f802c000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ hlcdc: hlcdc@f8038000 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9g45.dtsi b/arch/arm/dts/at91sam9g45.dtsi
index af8b708..1be1270 100644
--- a/arch/arm/dts/at91sam9g45.dtsi
+++ b/arch/arm/dts/at91sam9g45.dtsi
@@ -84,12 +84,14 @@
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ u-boot,dm-pre-reloc;
apb {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ u-boot,dm-pre-reloc;
aic: interrupt-controller@fffff000 {
#interrupt-cells = <3>;
@@ -121,6 +123,7 @@
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
+ u-boot,dm-pre-reloc;
main_osc: main_osc {
compatible = "atmel,at91rm9200-clk-main-osc";
@@ -135,7 +138,7 @@
clocks = <&main_osc>;
};
- plla: pllack {
+ plla: pllack@0 {
compatible = "atmel,at91rm9200-clk-pll";
#clock-cells = <0>;
interrupts-extended = <&pmc AT91_PMC_LOCKA>;
@@ -173,6 +176,7 @@
clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
atmel,clk-output-range = <0 133333333>;
atmel,clk-divisors = <1 2 4 3>;
+ u-boot,dm-pre-reloc;
};
usb: usbck {
@@ -188,13 +192,13 @@
interrupt-parent = <&pmc>;
clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
- prog0: prog0 {
+ prog0: prog@0 {
#clock-cells = <0>;
reg = <0>;
interrupts = <AT91_PMC_PCKRDY(0)>;
};
- prog1: prog1 {
+ prog1: prog@1 {
#clock-cells = <0>;
reg = <1>;
interrupts = <AT91_PMC_PCKRDY(1)>;
@@ -206,25 +210,25 @@
#address-cells = <1>;
#size-cells = <0>;
- ddrck: ddrck {
+ ddrck: ddrck@2 {
#clock-cells = <0>;
reg = <2>;
clocks = <&mck>;
};
- uhpck: uhpck {
+ uhpck: uhpck@6 {
#clock-cells = <0>;
reg = <6>;
clocks = <&usb>;
};
- pck0: pck0 {
+ pck0: pck0@8 {
#clock-cells = <0>;
reg = <8>;
clocks = <&prog0>;
};
- pck1: pck1 {
+ pck1: pck1@9 {
#clock-cells = <0>;
reg = <9>;
clocks = <&prog1>;
@@ -237,147 +241,147 @@
#size-cells = <0>;
clocks = <&mck>;
- pioA_clk: pioA_clk {
+ pioA_clk: pioA_clk@2 {
#clock-cells = <0>;
reg = <2>;
};
- pioB_clk: pioB_clk {
+ pioB_clk: pioB_clk@3 {
#clock-cells = <0>;
reg = <3>;
};
- pioC_clk: pioC_clk {
+ pioC_clk: pioC_clk@4 {
#clock-cells = <0>;
reg = <4>;
};
- pioDE_clk: pioDE_clk {
+ pioDE_clk: pioDE_clk@5 {
#clock-cells = <0>;
reg = <5>;
};
- trng_clk: trng_clk {
+ trng_clk: trng_clk@6 {
#clock-cells = <0>;
reg = <6>;
};
- usart0_clk: usart0_clk {
+ usart0_clk: usart0_clk@7 {
#clock-cells = <0>;
reg = <7>;
};
- usart1_clk: usart1_clk {
+ usart1_clk: usart1_clk@8 {
#clock-cells = <0>;
reg = <8>;
};
- usart2_clk: usart2_clk {
+ usart2_clk: usart2_clk@9 {
#clock-cells = <0>;
reg = <9>;
};
- usart3_clk: usart3_clk {
+ usart3_clk: usart3_clk@10 {
#clock-cells = <0>;
reg = <10>;
};
- mci0_clk: mci0_clk {
+ mci0_clk: mci0_clk@11 {
#clock-cells = <0>;
reg = <11>;
};
- twi0_clk: twi0_clk {
+ twi0_clk: twi0_clk@12 {
#clock-cells = <0>;
reg = <12>;
};
- twi1_clk: twi1_clk {
+ twi1_clk: twi1_clk@13 {
#clock-cells = <0>;
reg = <13>;
};
- spi0_clk: spi0_clk {
+ spi0_clk: spi0_clk@14 {
#clock-cells = <0>;
reg = <14>;
};
- spi1_clk: spi1_clk {
+ spi1_clk: spi1_clk@15 {
#clock-cells = <0>;
reg = <15>;
};
- ssc0_clk: ssc0_clk {
+ ssc0_clk: ssc0_clk@16 {
#clock-cells = <0>;
reg = <16>;
};
- ssc1_clk: ssc1_clk {
+ ssc1_clk: ssc1_clk@17 {
#clock-cells = <0>;
reg = <17>;
};
- tcb0_clk: tcb0_clk {
+ tcb0_clk: tcb0_clk@18 {
#clock-cells = <0>;
reg = <18>;
};
- pwm_clk: pwm_clk {
+ pwm_clk: pwm_clk@19 {
#clock-cells = <0>;
reg = <19>;
};
- adc_clk: adc_clk {
+ adc_clk: adc_clk@20 {
#clock-cells = <0>;
reg = <20>;
};
- dma0_clk: dma0_clk {
+ dma0_clk: dma0_clk@21 {
#clock-cells = <0>;
reg = <21>;
};
- uhphs_clk: uhphs_clk {
+ uhphs_clk: uhphs_clk@22 {
#clock-cells = <0>;
reg = <22>;
};
- lcd_clk: lcd_clk {
+ lcd_clk: lcd_clk@23 {
#clock-cells = <0>;
reg = <23>;
};
- ac97_clk: ac97_clk {
+ ac97_clk: ac97_clk@24 {
#clock-cells = <0>;
reg = <24>;
};
- macb0_clk: macb0_clk {
+ macb0_clk: macb0_clk@25 {
#clock-cells = <0>;
reg = <25>;
};
- isi_clk: isi_clk {
+ isi_clk: isi_clk@26 {
#clock-cells = <0>;
reg = <26>;
};
- udphs_clk: udphs_clk {
+ udphs_clk: udphs_clk@27 {
#clock-cells = <0>;
reg = <27>;
};
- aestdessha_clk: aestdessha_clk {
+ aestdessha_clk: aestdessha_clk@28 {
#clock-cells = <0>;
reg = <28>;
};
- mci1_clk: mci1_clk {
+ mci1_clk: mci1_clk@29 {
#clock-cells = <0>;
reg = <29>;
};
- vdec_clk: vdec_clk {
+ vdec_clk: vdec_clk@30 {
#clock-cells = <0>;
reg = <30>;
};
@@ -434,6 +438,13 @@
#size-cells = <1>;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff200 0xfffff200 0xa00>;
+ reg = <0xfffff200 0x200
+ 0xfffff400 0x200
+ 0xfffff600 0x200
+ 0xfffff800 0x200
+ 0xfffffa00 0x200
+ >;
+ u-boot,dm-pre-reloc;
atmel,mux-mask = <
/* A B */
@@ -476,10 +487,11 @@
};
dbgu {
+ u-boot,dm-pre-reloc;
pinctrl_dbgu: dbgu-0 {
atmel,pins =
- <AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB12 periph A */
- AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB13 periph A */
+ <AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_NONE>;
};
};
@@ -845,61 +857,61 @@
AT91_PIOE 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PE30 periph A */
};
};
+ };
- pioA: gpio@fffff200 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff200 0x200>;
- interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioA_clk>;
- };
+ pioA: gpio@fffff200 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff200 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioA_clk>;
+ };
- pioB: gpio@fffff400 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff400 0x200>;
- interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioB_clk>;
- };
+ pioB: gpio@fffff400 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioB_clk>;
+ };
- pioC: gpio@fffff600 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff600 0x200>;
- interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioC_clk>;
- };
+ pioC: gpio@fffff600 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioC_clk>;
+ };
- pioD: gpio@fffff800 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffff800 0x200>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioDE_clk>;
- };
+ pioD: gpio@fffff800 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioDE_clk>;
+ };
- pioE: gpio@fffffa00 {
- compatible = "atmel,at91rm9200-gpio";
- reg = <0xfffffa00 0x200>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <2>;
- clocks = <&pioDE_clk>;
- };
+ pioE: gpio@fffffa00 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioDE_clk>;
};
dbgu: serial@ffffee00 {
@@ -978,7 +990,7 @@
trng@fffcc000 {
compatible = "atmel,at91sam9g45-trng";
- reg = <0xfffcc000 0x4000>;
+ reg = <0xfffcc000 0x100>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&trng_clk>;
};
@@ -1044,28 +1056,24 @@
atmel,adc-res-names = "lowres", "highres";
atmel,adc-use-res = "highres";
- trigger@0 {
- reg = <0>;
+ trigger0 {
trigger-name = "external-rising";
trigger-value = <0x1>;
trigger-external;
};
- trigger@1 {
- reg = <1>;
+ trigger1 {
trigger-name = "external-falling";
trigger-value = <0x2>;
trigger-external;
};
- trigger@2 {
- reg = <2>;
+ trigger2 {
trigger-name = "external-any";
trigger-value = <0x3>;
trigger-external;
};
- trigger@3 {
- reg = <3>;
+ trigger3 {
trigger-name = "continuous";
trigger-value = <0x6>;
};
@@ -1169,13 +1177,13 @@
clock-names = "pclk", "hclk";
status = "disabled";
- ep0 {
+ ep@0 {
reg = <0>;
atmel,fifo-size = <64>;
atmel,nb-banks = <1>;
};
- ep1 {
+ ep@1 {
reg = <1>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
@@ -1183,7 +1191,7 @@
atmel,can-isoc;
};
- ep2 {
+ ep@2 {
reg = <2>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <2>;
@@ -1191,21 +1199,21 @@
atmel,can-isoc;
};
- ep3 {
+ ep@3 {
reg = <3>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep4 {
+ ep@4 {
reg = <4>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
atmel,can-dma;
};
- ep5 {
+ ep@5 {
reg = <5>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
@@ -1213,7 +1221,7 @@
atmel,can-isoc;
};
- ep6 {
+ ep@6 {
reg = <6>;
atmel,fifo-size = <1024>;
atmel,nb-banks = <3>;
@@ -1320,7 +1328,7 @@
};
};
- i2c@0 {
+ i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */
&pioA 21 GPIO_ACTIVE_HIGH /* scl */
diff --git a/arch/arm/dts/at91sam9m10g45ek.dts b/arch/arm/dts/at91sam9m10g45ek.dts
new file mode 100644
index 0000000..52a76fe
--- /dev/null
+++ b/arch/arm/dts/at91sam9m10g45ek.dts
@@ -0,0 +1,359 @@
+/*
+ * at91sam9m10g45ek.dts - Device Tree file for AT91SAM9M10G45-EK board
+ *
+ * Copyright (C) 2011 Atmel,
+ * 2011 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g45.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Atmel AT91SAM9M10G45-EK";
+ compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2";
+ stdout-path = "serial0:115200n8";
+ u-boot,dm-pre-reloc;
+ };
+
+ memory {
+ reg = <0x70000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial@ffffee00 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ };
+
+ usart1: serial@fff90000 {
+ pinctrl-0 =
+ <&pinctrl_usart1
+ &pinctrl_usart1_rts
+ &pinctrl_usart1_cts>;
+ status = "okay";
+ };
+
+ macb0: ethernet@fffbc000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ i2c0: i2c@fff84000 {
+ status = "okay";
+ ov2640: camera@30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>;
+ clocks = <&pck1>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <25000000>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
+
+ i2c1: i2c@fff88000 {
+ status = "okay";
+ };
+
+ watchdog@fffffd40 {
+ status = "okay";
+ };
+
+ mmc0: mmc@fff80000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_slot0_clk_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ mmc1: mmc@fffd0000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc1
+ &pinctrl_mmc1_slot0_clk_cmd_dat0
+ &pinctrl_mmc1_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ pinctrl@fffff200 {
+ camera_sensor {
+ pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOD 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOD 10 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD10 gpio CD pin pull up and deglitch */
+ };
+ };
+
+ mmc1 {
+ pinctrl_board_mmc1: mmc1-board {
+ atmel,pins =
+ <AT91_PIOD 11 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* PD11 gpio CD pin pull up and deglitch */
+ AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PD29 gpio WP pin pull up */
+ };
+ };
+
+ pwm0 {
+ pinctrl_pwm_leds: pwm-led {
+ atmel,pins =
+ <AT91_PIOD 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PD0 periph B */
+ AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PD31 periph B */
+ };
+ };
+ };
+
+ spi0: spi@fffa4000{
+ status = "okay";
+ cs-gpios = <&pioB 3 0>, <0>, <0>, <0>;
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <13000000>;
+ reg = <0>;
+ };
+ };
+
+ usb2: gadget@fff78000 {
+ atmel,vbus-gpio = <&pioB 19 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ adc0: adc@fffb0000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ &pinctrl_adc0_ad5
+ &pinctrl_adc0_ad6
+ &pinctrl_adc0_ad7>;
+ atmel,adc-ts-wires = <4>;
+ status = "okay";
+ };
+
+ isi@fffb4000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isi_data_0_7>;
+ status = "okay";
+ port {
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ vsync-active = <1>;
+ hsync-active = <1>;
+ };
+ };
+ };
+
+ pwm0: pwm@fffb8000 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm_leds>;
+ };
+
+ rtc@fffffd20 {
+ atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+ status = "okay";
+ };
+
+ gpbr: syscon@fffffd60 {
+ status = "okay";
+ };
+
+ rtc@fffffdb0 {
+ status = "okay";
+ };
+ };
+
+ fb0: fb@0x00500000 {
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <32>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <9>;
+ atmel,lcd-wiring-mode = "RGB";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <1>;
+ hfront-porch = <1>;
+ vback-porch = <40>;
+ vfront-porch = <1>;
+ hsync-len = <45>;
+ vsync-len = <1>;
+ };
+ };
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+
+ boot@0 {
+ label = "bootstrap/uboot/kernel";
+ reg = <0x0 0x400000>;
+ };
+
+ rootfs@400000 {
+ label = "rootfs";
+ reg = <0x400000 0x3C00000>;
+ };
+
+ data@4000000 {
+ label = "data";
+ reg = <0x4000000 0xC000000>;
+ };
+ };
+
+ usb0: ohci@00700000 {
+ status = "okay";
+ num-ports = <2>;
+ atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW
+ &pioD 3 GPIO_ACTIVE_LOW>;
+ };
+
+ usb1: ehci@00800000 {
+ status = "okay";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d8 {
+ label = "d8";
+ gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ d6 {
+ label = "d6";
+ pwms = <&pwm0 3 5000 PWM_POLARITY_INVERTED>;
+ max-brightness = <255>;
+ linux,default-trigger = "nand-disk";
+ };
+
+ d7 {
+ label = "d7";
+ pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>;
+ max-brightness = <255>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ left_click {
+ label = "left_click";
+ gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
+ linux,code = <272>;
+ wakeup-source;
+ };
+
+ right_click {
+ label = "right_click";
+ gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
+ linux,code = <273>;
+ wakeup-source;
+ };
+
+ left {
+ label = "Joystick Left";
+ gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
+ linux,code = <105>;
+ };
+
+ right {
+ label = "Joystick Right";
+ gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
+ linux,code = <106>;
+ };
+
+ up {
+ label = "Joystick Up";
+ gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
+ linux,code = <103>;
+ };
+
+ down {
+ label = "Joystick Down";
+ gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
+ linux,code = <108>;
+ };
+
+ enter {
+ label = "Joystick Press";
+ gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
+ linux,code = <28>;
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9n12.dtsi b/arch/arm/dts/at91sam9n12.dtsi
new file mode 100644
index 0000000..7ba7116
--- /dev/null
+++ b/arch/arm/dts/at91sam9n12.dtsi
@@ -0,0 +1,1064 @@
+/*
+ * at91sam9n12.dtsi - Device Tree include file for AT91SAM9N12 SoC
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Hong Xu <hong.xu@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/at91.h>
+
+/ {
+ model = "Atmel AT91SAM9N12 SoC";
+ compatible = "atmel,at91sam9n12";
+ interrupt-parent = <&aic>;
+
+ aliases {
+ serial0 = &dbgu;
+ serial1 = &usart0;
+ serial2 = &usart1;
+ serial3 = &usart2;
+ serial4 = &usart3;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ tcb0 = &tcb0;
+ tcb1 = &tcb1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ ssc0 = &ssc0;
+ pwm0 = &pwm0;
+ spi0 = &spi0;
+ };
+ cpus {
+ #address-cells = <0>;
+ #size-cells = <0>;
+
+ cpu {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ };
+ };
+
+ memory {
+ reg = <0x20000000 0x10000000>;
+ };
+
+ clocks {
+ slow_xtal: slow_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ main_xtal: main_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ sram: sram@00300000 {
+ compatible = "mmio-sram";
+ reg = <0x00300000 0x8000>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ u-boot,dm-pre-reloc;
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ u-boot,dm-pre-reloc;
+
+ aic: interrupt-controller@fffff000 {
+ #interrupt-cells = <3>;
+ compatible = "atmel,at91rm9200-aic";
+ interrupt-controller;
+ reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <31>;
+ };
+
+ ramc0: ramc@ffffe800 {
+ compatible = "atmel,at91sam9g45-ddramc";
+ reg = <0xffffe800 0x200>;
+ clocks = <&ddrck>;
+ clock-names = "ddrck";
+ };
+
+ pmc: pmc@fffffc00 {
+ compatible = "atmel,at91sam9n12-pmc", "syscon";
+ reg = <0xfffffc00 0x200>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+ u-boot,dm-pre-reloc;
+
+ main_rc_osc: main_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-main-rc-osc";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCRCS>;
+ clock-frequency = <12000000>;
+ clock-accuracy = <50000000>;
+ };
+
+ main_osc: main_osc {
+ compatible = "atmel,at91rm9200-clk-main-osc";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCS>;
+ clocks = <&main_xtal>;
+ };
+
+ main: mainck {
+ compatible = "atmel,at91sam9x5-clk-main";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCSELS>;
+ clocks = <&main_rc_osc>, <&main_osc>;
+ };
+
+ plla: pllack@0 {
+ compatible = "atmel,at91rm9200-clk-pll";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_LOCKA>;
+ clocks = <&main>;
+ reg = <0>;
+ atmel,clk-input-range = <2000000 32000000>;
+ #atmel,pll-clk-output-range-cells = <4>;
+ atmel,pll-clk-output-ranges = <745000000 800000000 0 0>,
+ <695000000 750000000 1 0>,
+ <645000000 700000000 2 0>,
+ <595000000 650000000 3 0>,
+ <545000000 600000000 0 1>,
+ <495000000 555000000 1 1>,
+ <445000000 500000000 2 1>,
+ <400000000 450000000 3 1>;
+ };
+
+ plladiv: plladivck {
+ compatible = "atmel,at91sam9x5-clk-plldiv";
+ #clock-cells = <0>;
+ clocks = <&plla>;
+ };
+
+ pllb: pllbck@1 {
+ compatible = "atmel,at91rm9200-clk-pll";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_LOCKB>;
+ clocks = <&main>;
+ reg = <1>;
+ atmel,clk-input-range = <2000000 32000000>;
+ #atmel,pll-clk-output-range-cells = <3>;
+ atmel,pll-clk-output-ranges = <30000000 100000000 0>;
+ };
+
+ mck: masterck {
+ compatible = "atmel,at91sam9x5-clk-master";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>;
+ atmel,clk-output-range = <0 133333333>;
+ atmel,clk-divisors = <1 2 4 3>;
+ atmel,master-clk-have-div3-pres;
+ u-boot,dm-pre-reloc;
+ };
+
+ usb: usbck {
+ compatible = "atmel,at91sam9n12-clk-usb";
+ #clock-cells = <0>;
+ clocks = <&pllb>;
+ };
+
+ prog: progck {
+ compatible = "atmel,at91sam9x5-clk-programmable";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>, <&mck>;
+
+ prog0: prog@0 {
+ #clock-cells = <0>;
+ reg = <0>;
+ interrupts = <AT91_PMC_PCKRDY(0)>;
+ };
+
+ prog1: prog@1 {
+ #clock-cells = <0>;
+ reg = <1>;
+ interrupts = <AT91_PMC_PCKRDY(1)>;
+ };
+ };
+
+ systemck {
+ compatible = "atmel,at91rm9200-clk-system";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ddrck: ddrck@2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ clocks = <&mck>;
+ };
+
+ lcdck: lcdck@3 {
+ #clock-cells = <0>;
+ reg = <3>;
+ clocks = <&mck>;
+ };
+
+ uhpck: uhpck@6 {
+ #clock-cells = <0>;
+ reg = <6>;
+ clocks = <&usb>;
+ };
+
+ udpck: udpck@7 {
+ #clock-cells = <0>;
+ reg = <7>;
+ clocks = <&usb>;
+ };
+
+ pck0: pck0@8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ clocks = <&prog0>;
+ };
+
+ pck1: pck1@9 {
+ #clock-cells = <0>;
+ reg = <9>;
+ clocks = <&prog1>;
+ };
+ };
+
+ periphck {
+ compatible = "atmel,at91sam9x5-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mck>;
+ u-boot,dm-pre-reloc;
+
+ pioAB_clk: pioAB_clk@2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioCD_clk: pioCD_clk@3 {
+ #clock-cells = <0>;
+ reg = <3>;
+ u-boot,dm-pre-reloc;
+ };
+
+ fuse_clk: fuse_clk@4 {
+ #clock-cells = <0>;
+ reg = <4>;
+ };
+
+ usart0_clk: usart0_clk@5 {
+ #clock-cells = <0>;
+ reg = <5>;
+ };
+
+ usart1_clk: usart1_clk@6 {
+ #clock-cells = <0>;
+ reg = <6>;
+ };
+
+ usart2_clk: usart2_clk@7 {
+ #clock-cells = <0>;
+ reg = <7>;
+ };
+
+ usart3_clk: usart3_clk@8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ };
+
+ twi0_clk: twi0_clk@9 {
+ reg = <9>;
+ #clock-cells = <0>;
+ };
+
+ twi1_clk: twi1_clk@10 {
+ #clock-cells = <0>;
+ reg = <10>;
+ };
+
+ mci0_clk: mci0_clk@12 {
+ #clock-cells = <0>;
+ reg = <12>;
+ };
+
+ spi0_clk: spi0_clk@13 {
+ #clock-cells = <0>;
+ reg = <13>;
+ };
+
+ spi1_clk: spi1_clk@14 {
+ #clock-cells = <0>;
+ reg = <14>;
+ };
+
+ uart0_clk: uart0_clk@15 {
+ #clock-cells = <0>;
+ reg = <15>;
+ };
+
+ uart1_clk: uart1_clk@16 {
+ #clock-cells = <0>;
+ reg = <16>;
+ };
+
+ tcb_clk: tcb_clk@17 {
+ #clock-cells = <0>;
+ reg = <17>;
+ };
+
+ pwm_clk: pwm_clk@18 {
+ #clock-cells = <0>;
+ reg = <18>;
+ };
+
+ adc_clk: adc_clk@19 {
+ #clock-cells = <0>;
+ reg = <19>;
+ };
+
+ dma0_clk: dma0_clk@20 {
+ #clock-cells = <0>;
+ reg = <20>;
+ };
+
+ uhphs_clk: uhphs_clk@22 {
+ #clock-cells = <0>;
+ reg = <22>;
+ };
+
+ udphs_clk: udphs_clk@23 {
+ #clock-cells = <0>;
+ reg = <23>;
+ };
+
+ lcdc_clk: lcdc_clk@25 {
+ #clock-cells = <0>;
+ reg = <25>;
+ };
+
+ sha_clk: sha_clk@27 {
+ #clock-cells = <0>;
+ reg = <27>;
+ };
+
+ ssc0_clk: ssc0_clk@28 {
+ #clock-cells = <0>;
+ reg = <28>;
+ };
+
+ aes_clk: aes_clk@29 {
+ #clock-cells = <0>;
+ reg = <29>;
+ };
+
+ trng_clk: trng_clk@30 {
+ #clock-cells = <0>;
+ reg = <30>;
+ };
+ };
+ };
+
+ rstc@fffffe00 {
+ compatible = "atmel,at91sam9g45-rstc";
+ reg = <0xfffffe00 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ pit: timer@fffffe30 {
+ compatible = "atmel,at91sam9260-pit";
+ reg = <0xfffffe30 0xf>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&mck>;
+ };
+
+ shdwc@fffffe10 {
+ compatible = "atmel,at91sam9x5-shdwc";
+ reg = <0xfffffe10 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ sckc@fffffe50 {
+ compatible = "atmel,at91sam9x5-sckc";
+ reg = <0xfffffe50 0x4>;
+
+ slow_osc: slow_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-osc";
+ #clock-cells = <0>;
+ clocks = <&slow_xtal>;
+ };
+
+ slow_rc_osc: slow_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-accuracy = <50000000>;
+ };
+
+ clk32k: slck {
+ compatible = "atmel,at91sam9x5-clk-slow";
+ #clock-cells = <0>;
+ clocks = <&slow_rc_osc>, <&slow_osc>;
+ };
+ };
+
+ mmc0: mmc@f0008000 {
+ compatible = "atmel,hsmci";
+ reg = <0xf0008000 0x600>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma 1 AT91_DMA_CFG_PER_ID(0)>;
+ dma-names = "rxtx";
+ clocks = <&mci0_clk>;
+ clock-names = "mci_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ tcb0: timer@f8008000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xf8008000 0x100>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tcb_clk>, <&clk32k>;
+ clock-names = "t0_clk", "slow_clk";
+ };
+
+ tcb1: timer@f800c000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xf800c000 0x100>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tcb_clk>, <&clk32k>;
+ clock-names = "t0_clk", "slow_clk";
+ };
+
+ hlcdc: hlcdc@f8038000 {
+ compatible = "atmel,at91sam9n12-hlcdc";
+ reg = <0xf8038000 0x2000>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+ clock-names = "periph_clk", "sys_clk", "slow_clk";
+ status = "disabled";
+
+ hlcdc-display-controller {
+ compatible = "atmel,hlcdc-display-controller";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ };
+
+ hlcdc_pwm: hlcdc-pwm {
+ compatible = "atmel,hlcdc-pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwm>;
+ #pwm-cells = <3>;
+ };
+ };
+
+ dma: dma-controller@ffffec00 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffec00 0x200>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <2>;
+ clocks = <&dma0_clk>;
+ clock-names = "dma_clk";
+ };
+
+ pinctrl@fffff400 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+ ranges = <0xfffff400 0xfffff400 0x800>;
+ reg = <0xfffff400 0x200
+ 0xfffff600 0x200
+ 0xfffff800 0x200
+ 0xfffffa00 0x200
+ >;
+
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe07983 0x00000000 /* pioA */
+ 0x00040000 0x00047e0f 0x00000000 /* pioB */
+ 0xfdffffff 0x07c00000 0xb83fffff /* pioC */
+ 0x003fffff 0x003f8000 0x00000000 /* pioD */
+ >;
+ u-boot,dm-pre-reloc;
+
+ /* shared pinctrl settings */
+ dbgu {
+ u-boot,dm-pre-reloc;
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins =
+ <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ lcd {
+ pinctrl_lcd_base: lcd-base-0 {
+ atmel,pins =
+ <AT91_PIOC 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDVSYNC */
+ AT91_PIOC 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDHSYNC */
+ AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDDISP */
+ AT91_PIOC 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDDEN */
+ AT91_PIOC 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDPCK */
+ };
+
+ pinctrl_lcd_pwm: lcd-pwm-0 {
+ atmel,pins = <AT91_PIOC 26 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDPWM */
+ };
+
+ pinctrl_lcd_rgb888: lcd-rgb-3 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOC 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD15 pin */
+ AT91_PIOC 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD16 pin */
+ AT91_PIOC 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD17 pin */
+ AT91_PIOC 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD18 pin */
+ AT91_PIOC 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD19 pin */
+ AT91_PIOC 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD20 pin */
+ AT91_PIOC 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD21 pin */
+ AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD22 pin */
+ AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD23 pin */
+ };
+ };
+
+ usart0 {
+ pinctrl_usart0: usart0-0 {
+ atmel,pins =
+ <AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA1 periph A with pullup */
+ AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA0 periph A */
+ };
+
+ pinctrl_usart0_rts: usart0_rts-0 {
+ atmel,pins =
+ <AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA2 periph A */
+ };
+
+ pinctrl_usart0_cts: usart0_cts-0 {
+ atmel,pins =
+ <AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA3 periph A */
+ };
+ };
+
+ usart1 {
+ pinctrl_usart1: usart1-0 {
+ atmel,pins =
+ <AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA6 periph A with pullup */
+ AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA5 periph A */
+ };
+ };
+
+ usart2 {
+ pinctrl_usart2: usart2-0 {
+ atmel,pins =
+ <AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA8 periph A with pullup */
+ AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA7 periph A */
+ };
+
+ pinctrl_usart2_rts: usart2_rts-0 {
+ atmel,pins =
+ <AT91_PIOB 0 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB0 periph B */
+ };
+
+ pinctrl_usart2_cts: usart2_cts-0 {
+ atmel,pins =
+ <AT91_PIOB 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB1 periph B */
+ };
+ };
+
+ usart3 {
+ pinctrl_usart3: usart3-0 {
+ atmel,pins =
+ <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PC23 periph B with pullup */
+ AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC22 periph B */
+ };
+
+ pinctrl_usart3_rts: usart3_rts-0 {
+ atmel,pins =
+ <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC24 periph B */
+ };
+
+ pinctrl_usart3_cts: usart3_cts-0 {
+ atmel,pins =
+ <AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC25 periph B */
+ };
+ };
+
+ uart0 {
+ pinctrl_uart0: uart0-0 {
+ atmel,pins =
+ <AT91_PIOC 9 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* PC9 periph C with pullup */
+ AT91_PIOC 8 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC8 periph C */
+ };
+ };
+
+ uart1 {
+ pinctrl_uart1: uart1-0 {
+ atmel,pins =
+ <AT91_PIOC 16 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* PC17 periph C with pullup */
+ AT91_PIOC 17 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC16 periph C */
+ };
+ };
+
+ nand {
+ pinctrl_nand: nand-0 {
+ atmel,pins =
+ <AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PD5 gpio RDY pin pull_up*/
+ AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PD4 gpio enable pin pull_up */
+ };
+ };
+
+ mmc0 {
+ pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 {
+ atmel,pins =
+ <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA17 periph A */
+ AT91_PIOA 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA16 periph A with pullup */
+ AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA15 periph A with pullup */
+ };
+
+ pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 {
+ atmel,pins =
+ <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA18 periph A with pullup */
+ AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA19 periph A with pullup */
+ AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA20 periph A with pullup */
+ };
+
+ pinctrl_mmc0_slot0_dat4_7: mmc0_slot0_dat4_7-0 {
+ atmel,pins =
+ <AT91_PIOA 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA11 periph B with pullup */
+ AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA12 periph B with pullup */
+ AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA13 periph B with pullup */
+ AT91_PIOA 14 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA14 periph B with pullup */
+ };
+ };
+
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins =
+ <AT91_PIOA 24 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA24 periph B */
+ AT91_PIOA 25 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA25 periph B */
+ AT91_PIOA 26 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA26 periph B */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins =
+ <AT91_PIOA 27 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA27 periph B */
+ AT91_PIOA 28 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA28 periph B */
+ AT91_PIOA 29 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA29 periph B */
+ };
+ };
+
+ spi0 {
+ pinctrl_spi0: spi0-0 {
+ atmel,pins =
+ <AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA11 periph A SPI0_MISO pin */
+ AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA12 periph A SPI0_MOSI pin */
+ AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA13 periph A SPI0_SPCK pin */
+ };
+ };
+
+ spi1 {
+ pinctrl_spi1: spi1-0 {
+ atmel,pins =
+ <AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA21 periph B SPI1_MISO pin */
+ AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA22 periph B SPI1_MOSI pin */
+ AT91_PIOA 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA23 periph B SPI1_SPCK pin */
+ };
+ };
+
+ i2c0 {
+ pinctrl_i2c0: i2c0-0 {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ i2c1 {
+ pinctrl_i2c1: i2c1-0 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
+ AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ };
+
+ tcb0 {
+ pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
+ atmel,pins = <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tclk1: tcb0_tclk1-0 {
+ atmel,pins = <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tclk2: tcb0_tclk2-0 {
+ atmel,pins = <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa0: tcb0_tioa0-0 {
+ atmel,pins = <AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa1: tcb0_tioa1-0 {
+ atmel,pins = <AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa2: tcb0_tioa2-0 {
+ atmel,pins = <AT91_PIOA 23 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob0: tcb0_tiob0-0 {
+ atmel,pins = <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob1: tcb0_tiob1-0 {
+ atmel,pins = <AT91_PIOA 28 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob2: tcb0_tiob2-0 {
+ atmel,pins = <AT91_PIOA 29 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ tcb1 {
+ pinctrl_tcb1_tclk0: tcb1_tclk0-0 {
+ atmel,pins = <AT91_PIOC 4 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tclk1: tcb1_tclk1-0 {
+ atmel,pins = <AT91_PIOC 7 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tclk2: tcb1_tclk2-0 {
+ atmel,pins = <AT91_PIOC 14 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tioa0: tcb1_tioa0-0 {
+ atmel,pins = <AT91_PIOC 2 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tioa1: tcb1_tioa1-0 {
+ atmel,pins = <AT91_PIOC 5 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tioa2: tcb1_tioa2-0 {
+ atmel,pins = <AT91_PIOC 12 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tiob0: tcb1_tiob0-0 {
+ atmel,pins = <AT91_PIOC 3 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tiob1: tcb1_tiob1-0 {
+ atmel,pins = <AT91_PIOC 6 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tiob2: tcb1_tiob2-0 {
+ atmel,pins = <AT91_PIOC 13 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ };
+ };
+
+ pioA: gpio@fffff400 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioAB_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioB: gpio@fffff600 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioAB_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioC: gpio@fffff800 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioCD_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioD: gpio@fffffa00 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioCD_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ dbgu: serial@fffff200 {
+ compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0xfffff200 0x200>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ clocks = <&mck>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ ssc0: ssc@f0010000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xf0010000 0x4000>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma 0 AT91_DMA_CFG_PER_ID(21)>,
+ <&dma 0 AT91_DMA_CFG_PER_ID(22)>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ clocks = <&ssc0_clk>;
+ clock-names = "pclk";
+ status = "disabled";
+ };
+
+ usart0: serial@f801c000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf801c000 0x4000>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart0>;
+ clocks = <&usart0_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart1: serial@f8020000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8020000 0x4000>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1>;
+ clocks = <&usart1_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart2: serial@f8024000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8024000 0x4000>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart2>;
+ clocks = <&usart2_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart3: serial@f8028000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8028000 0x4000>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3>;
+ clocks = <&usart3_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ i2c0: i2c@f8010000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf8010000 0x100>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma 1 AT91_DMA_CFG_PER_ID(13)>,
+ <&dma 1 AT91_DMA_CFG_PER_ID(14)>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ clocks = <&twi0_clk>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@f8014000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf8014000 0x100>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma 1 AT91_DMA_CFG_PER_ID(15)>,
+ <&dma 1 AT91_DMA_CFG_PER_ID(16)>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clocks = <&twi1_clk>;
+ status = "disabled";
+ };
+
+ spi0: spi@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xf0000000 0x100>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
+ dmas = <&dma 1 AT91_DMA_CFG_PER_ID(1)>,
+ <&dma 1 AT91_DMA_CFG_PER_ID(2)>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0>;
+ clocks = <&spi0_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ spi1: spi@f0004000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xf0004000 0x100>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 3>;
+ dmas = <&dma 1 AT91_DMA_CFG_PER_ID(3)>,
+ <&dma 1 AT91_DMA_CFG_PER_ID(4)>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1>;
+ clocks = <&spi1_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ watchdog@fffffe40 {
+ compatible = "atmel,at91sam9260-wdt";
+ reg = <0xfffffe40 0x10>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ atmel,watchdog-type = "hardware";
+ atmel,reset-type = "all";
+ atmel,dbg-halt;
+ status = "disabled";
+ };
+
+ rtc@fffffeb0 {
+ compatible = "atmel,at91rm9200-rtc";
+ reg = <0xfffffeb0 0x40>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@f8034000 {
+ compatible = "atmel,at91sam9rl-pwm";
+ reg = <0xf8034000 0x300>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
+ #pwm-cells = <3>;
+ clocks = <&pwm_clk>;
+ status = "disabled";
+ };
+
+ usb1: gadget@f803c000 {
+ compatible = "atmel,at91sam9260-udc";
+ reg = <0xf803c000 0x4000>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&udphs_clk>, <&udpck>;
+ clock-names = "pclk", "hclk";
+ status = "disabled";
+ };
+ };
+
+ nand0: nand@40000000 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = < 0x40000000 0x10000000
+ 0xffffe000 0x00000600
+ 0xffffe600 0x00000200
+ 0x00108000 0x00018000
+ >;
+ atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
+ atmel,nand-addr-offset = <21>;
+ atmel,nand-cmd-offset = <22>;
+ atmel,nand-has-dma;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand>;
+ gpios = <&pioD 5 GPIO_ACTIVE_HIGH
+ &pioD 4 GPIO_ACTIVE_HIGH
+ 0
+ >;
+ status = "disabled";
+ };
+
+ usb0: ohci@00500000 {
+ compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+ reg = <0x00500000 0x00100000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+ clock-names = "ohci_clk", "hclk", "uhpck";
+ status = "disabled";
+ };
+ };
+
+ i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
+ &pioA 31 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,sda-open-drain;
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+};
diff --git a/arch/arm/dts/at91sam9n12ek.dts b/arch/arm/dts/at91sam9n12ek.dts
new file mode 100644
index 0000000..888bda1
--- /dev/null
+++ b/arch/arm/dts/at91sam9n12ek.dts
@@ -0,0 +1,265 @@
+/*
+ * at91sam9n12ek.dts - Device Tree file for AT91SAM9N12-EK board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Hong Xu <hong.xu@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9n12.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9N12-EK";
+ compatible = "atmel,at91sam9n12ek", "atmel,at91sam9n12", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "root=/dev/mtdblock1 rw rootfstype=jffs2";
+ stdout-path = "serial0:115200n8";
+ u-boot,dm-pre-reloc;
+ };
+
+ memory {
+ reg = <0x20000000 0x8000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <16000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial@fffff200 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ ssc0: ssc@f0010000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@f8010000 {
+ status = "okay";
+
+ wm8904: codec@1a {
+ compatible = "wlf,wm8904";
+ reg = <0x1a>;
+ clocks = <&pck0>;
+ clock-names = "mclk";
+ };
+
+ qt1070: keyboard@1b {
+ compatible = "qt1070";
+ reg = <0x1b>;
+ interrupt-parent = <&pioA>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qt1070_irq>;
+ };
+ };
+
+ mmc0: mmc@f0008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_slot0_clk_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ pinctrl@fffff400 {
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PA7 gpio CD pin pull up and deglitch */
+ };
+ };
+
+ qt1070 {
+ pinctrl_qt1070_irq: qt1070_irq {
+ atmel,pins =
+ <AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ };
+
+ sound {
+ pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+ atmel,pins =
+ <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usb1 {
+ pinctrl_usb1_vbus_sense: usb1_vbus_sense {
+ atmel,pins =
+ <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio usb vbus sense, no pull up and deglitch */
+ };
+ };
+ };
+
+ spi0: spi@f0000000 {
+ status = "okay";
+ cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
+ spi_flash@0 {
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ hlcdc: hlcdc@f8038000 {
+ status = "okay";
+
+ hlcdc-display-controller {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+
+ port@0 {
+ hlcdc_panel_output: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+ };
+ };
+ };
+
+ usb1: gadget@f803c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1_vbus_sense>;
+ atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+
+ rtc@fffffeb0 {
+ status = "okay";
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <2>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+ status = "okay";
+ };
+
+ usb0: ohci@00500000 {
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioB 7 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&hlcdc_pwm 0 50000 0>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ power-supply = <&bl_reg>;
+ status = "okay";
+ };
+
+ bl_reg: backlight_regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "backlight-power-supply";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ status = "okay";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ d8 {
+ label = "d8";
+ gpios = <&pioB 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "mmc0";
+ };
+
+ d9 {
+ label = "d9";
+ gpios = <&pioB 5 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "nand-disk";
+ };
+
+ d10 {
+ label = "d10";
+ gpios = <&pioB 6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ enter {
+ label = "Enter";
+ gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
+ linux,code = <28>;
+ wakeup-source;
+ };
+ };
+
+ panel: panel {
+ compatible = "qiaodian,qd43003c0-40", "simple-panel";
+ backlight = <&backlight>;
+ power-supply = <&panel_reg>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&hlcdc_panel_output>;
+ };
+ };
+ };
+
+ panel_reg: panel_regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "panel-power-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ status = "okay";
+ };
+
+ sound {
+ compatible = "atmel,asoc-wm8904";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+ atmel,model = "wm8904 @ AT91SAM9N12";
+ atmel,audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "IN2L", "Line In Jack",
+ "IN2R", "Line In Jack",
+ "Mic", "MICBIAS",
+ "IN1L", "Mic";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8904>;
+ };
+};
diff --git a/arch/arm/dts/at91sam9rl.dtsi b/arch/arm/dts/at91sam9rl.dtsi
new file mode 100644
index 0000000..8249994
--- /dev/null
+++ b/arch/arm/dts/at91sam9rl.dtsi
@@ -0,0 +1,1139 @@
+/*
+ * at91sam9rl.dtsi - Device Tree Include file for AT91SAM9RL family SoC
+ *
+ * Copyright (C) 2014 Alexandre Belloni <alexandre.belloni@free-electrons.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Atmel AT91SAM9RL family SoC";
+ compatible = "atmel,at91sam9rl", "atmel,at91sam9";
+ interrupt-parent = <&aic>;
+
+ aliases {
+ serial0 = &dbgu;
+ serial1 = &usart0;
+ serial2 = &usart1;
+ serial3 = &usart2;
+ serial4 = &usart3;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ tcb0 = &tcb0;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ ssc0 = &ssc0;
+ ssc1 = &ssc1;
+ pwm0 = &pwm0;
+ };
+
+ cpus {
+ #address-cells = <0>;
+ #size-cells = <0>;
+
+ cpu {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ };
+ };
+
+ memory {
+ reg = <0x20000000 0x04000000>;
+ };
+
+ clocks {
+ slow_xtal: slow_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ main_xtal: main_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ adc_op_clk: adc_op_clk{
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1000000>;
+ };
+ };
+
+ sram: sram@00300000 {
+ compatible = "mmio-sram";
+ reg = <0x00300000 0x10000>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ u-boot,dm-pre-reloc;
+
+ fb0: fb@00500000 {
+ compatible = "atmel,at91sam9rl-lcdc";
+ reg = <0x00500000 0x1000>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ clocks = <&lcd_clk>, <&lcd_clk>;
+ clock-names = "hclk", "lcdc_clk";
+ status = "disabled";
+ };
+
+ nand0: nand@40000000 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x40000000 0x10000000>,
+ <0xffffe800 0x200>;
+ atmel,nand-addr-offset = <21>;
+ atmel,nand-cmd-offset = <22>;
+ atmel,nand-has-dma;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand>;
+ gpios = <&pioD 17 GPIO_ACTIVE_HIGH>,
+ <&pioB 6 GPIO_ACTIVE_HIGH>,
+ <0>;
+ status = "disabled";
+ };
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ u-boot,dm-pre-reloc;
+
+ tcb0: timer@fffa0000 {
+ compatible = "atmel,at91rm9200-tcb";
+ reg = <0xfffa0000 0x100>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 0>,
+ <17 IRQ_TYPE_LEVEL_HIGH 0>,
+ <18 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>, <&clk32k>;
+ clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
+ };
+
+ mmc0: mmc@fffa4000 {
+ compatible = "atmel,hsmci";
+ reg = <0xfffa4000 0x600>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ clocks = <&mci0_clk>;
+ clock-names = "mci_clk";
+ status = "disabled";
+ };
+
+ i2c0: i2c@fffa8000 {
+ compatible = "atmel,at91sam9260-i2c";
+ reg = <0xfffa8000 0x100>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&twi0_clk>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@fffac000 {
+ compatible = "atmel,at91sam9260-i2c";
+ reg = <0xfffac000 0x100>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usart0: serial@fffb0000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfffb0000 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart0>;
+ clocks = <&usart0_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart1: serial@fffb4000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfffb4000 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1>;
+ clocks = <&usart1_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart2: serial@fffb8000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfffb8000 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart2>;
+ clocks = <&usart2_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart3: serial@fffbc000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfffbc000 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3>;
+ clocks = <&usart3_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ ssc0: ssc@fffc0000 {
+ compatible = "atmel,at91sam9rl-ssc";
+ reg = <0xfffc0000 0x4000>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ status = "disabled";
+ };
+
+ ssc1: ssc@fffc4000 {
+ compatible = "atmel,at91sam9rl-ssc";
+ reg = <0xfffc4000 0x4000>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@fffc8000 {
+ compatible = "atmel,at91sam9rl-pwm";
+ reg = <0xfffc8000 0x300>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>;
+ #pwm-cells = <3>;
+ clocks = <&pwm_clk>;
+ clock-names = "pwm_clk";
+ status = "disabled";
+ };
+
+ spi0: spi@fffcc000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xfffcc000 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0>;
+ clocks = <&spi0_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ adc0: adc@fffd0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91sam9rl-adc";
+ reg = <0xfffd0000 0x100>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&adc_clk>, <&adc_op_clk>;
+ clock-names = "adc_clk", "adc_op_clk";
+ atmel,adc-use-external-triggers;
+ atmel,adc-channels-used = <0x3f>;
+ atmel,adc-vref = <3300>;
+ atmel,adc-startup-time = <40>;
+ atmel,adc-res = <8 10>;
+ atmel,adc-res-names = "lowres", "highres";
+ atmel,adc-use-res = "highres";
+
+ trigger0 {
+ trigger-name = "timer-counter-0";
+ trigger-value = <0x1>;
+ };
+ trigger1 {
+ trigger-name = "timer-counter-1";
+ trigger-value = <0x3>;
+ };
+
+ trigger2 {
+ trigger-name = "timer-counter-2";
+ trigger-value = <0x5>;
+ };
+
+ trigger3 {
+ trigger-name = "external";
+ trigger-value = <0x13>;
+ trigger-external;
+ };
+ };
+
+ usb0: gadget@fffd4000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91sam9rl-udc";
+ reg = <0x00600000 0x100000>,
+ <0xfffd4000 0x4000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&udphs_clk>, <&utmi>;
+ clock-names = "pclk", "hclk";
+ status = "disabled";
+
+ ep@0 {
+ reg = <0>;
+ atmel,fifo-size = <64>;
+ atmel,nb-banks = <1>;
+ };
+
+ ep@1 {
+ reg = <1>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep@2 {
+ reg = <2>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep@3 {
+ reg = <3>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ };
+
+ ep@4 {
+ reg = <4>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ };
+
+ ep@5 {
+ reg = <5>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep@6 {
+ reg = <6>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+ };
+
+ dma0: dma-controller@ffffe600 {
+ compatible = "atmel,at91sam9rl-dma";
+ reg = <0xffffe600 0x200>;
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <2>;
+ clocks = <&dma0_clk>;
+ clock-names = "dma_clk";
+ };
+
+ ramc0: ramc@ffffea00 {
+ compatible = "atmel,at91sam9260-sdramc";
+ reg = <0xffffea00 0x200>;
+ };
+
+ aic: interrupt-controller@fffff000 {
+ #interrupt-cells = <3>;
+ compatible = "atmel,at91rm9200-aic";
+ interrupt-controller;
+ reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <31>;
+ };
+
+ dbgu: serial@fffff200 {
+ compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0xfffff200 0x200>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ clocks = <&mck>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ pinctrl@fffff400 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+ ranges = <0xfffff400 0xfffff400 0x800>;
+ reg = <0xfffff400 0x200
+ 0xfffff600 0x200
+ 0xfffff800 0x200
+ 0xfffffa00 0x200
+ >;
+
+ atmel,mux-mask =
+ /* A B */
+ <0xffffffff 0xe05c6738>, /* pioA */
+ <0xffffffff 0x0000c780>, /* pioB */
+ <0xffffffff 0xe3ffff0e>, /* pioC */
+ <0x003fffff 0x0001ff3c>; /* pioD */
+ u-boot,dm-pre-reloc;
+
+ /* shared pinctrl settings */
+ adc0 {
+ pinctrl_adc0_ts: adc0_ts-0 {
+ atmel,pins =
+ <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adc0_ad0: adc0_ad0-0 {
+ atmel,pins = <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adc0_ad1: adc0_ad1-0 {
+ atmel,pins = <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adc0_ad2: adc0_ad2-0 {
+ atmel,pins = <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adc0_ad3: adc0_ad3-0 {
+ atmel,pins = <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adc0_ad4: adc0_ad4-0 {
+ atmel,pins = <AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adc0_ad5: adc0_ad5-0 {
+ atmel,pins = <AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adc0_adtrg: adc0_adtrg-0 {
+ atmel,pins = <AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ dbgu {
+ u-boot,dm-pre-reloc;
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins =
+ <AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ fb {
+ pinctrl_fb: fb-0 {
+ atmel,pins =
+ <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 15 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ i2c_gpio0 {
+ pinctrl_i2c_gpio0: i2c_gpio0-0 {
+ atmel,pins =
+ <AT91_PIOA 23 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>,
+ <AT91_PIOA 24 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+ };
+ };
+
+ i2c_gpio1 {
+ pinctrl_i2c_gpio1: i2c_gpio1-0 {
+ atmel,pins =
+ <AT91_PIOD 10 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>,
+ <AT91_PIOD 11 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+ };
+ };
+
+ mmc0 {
+ pinctrl_mmc0_clk: mmc0_clk-0 {
+ atmel,pins =
+ <AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_mmc0_slot0_cmd_dat0: mmc0_slot0_cmd_dat0-0 {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 {
+ atmel,pins =
+ <AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ nand {
+ pinctrl_nand: nand-0 {
+ atmel,pins =
+ <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOB 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_nand0_ale_cle: nand_ale_cle-0 {
+ atmel,pins =
+ <AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_nand0_oe_we: nand_oe_we-0 {
+ atmel,pins =
+ <AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_nand0_cs: nand_cs-0 {
+ atmel,pins =
+ <AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ pwm0 {
+ pinctrl_pwm0_pwm0_0: pwm0_pwm0-0 {
+ atmel,pins = <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm0_1: pwm0_pwm0-1 {
+ atmel,pins = <AT91_PIOC 2 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm0_2: pwm0_pwm0-2 {
+ atmel,pins = <AT91_PIOD 14 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm1_0: pwm0_pwm1-0 {
+ atmel,pins = <AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm1_1: pwm0_pwm1-1 {
+ atmel,pins = <AT91_PIOC 3 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm1_2: pwm0_pwm1-2 {
+ atmel,pins = <AT91_PIOD 15 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm2_0: pwm0_pwm2-0 {
+ atmel,pins = <AT91_PIOD 5 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm2_1: pwm0_pwm2-1 {
+ atmel,pins = <AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm2_2: pwm0_pwm2-2 {
+ atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm3_0: pwm0_pwm3-0 {
+ atmel,pins = <AT91_PIOD 8 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm3_1: pwm0_pwm3-1 {
+ atmel,pins = <AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ spi0 {
+ pinctrl_spi0: spi0-0 {
+ atmel,pins =
+ <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins =
+ <AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins =
+ <AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOA 16 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ ssc1 {
+ pinctrl_ssc1_tx: ssc1_tx-0 {
+ atmel,pins =
+ <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOA 29 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_ssc1_rx: ssc1_rx-0 {
+ atmel,pins =
+ <AT91_PIOA 8 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE>,
+ <AT91_PIOA 14 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ tcb0 {
+ pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
+ atmel,pins = <AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tclk1: tcb0_tclk1-0 {
+ atmel,pins = <AT91_PIOC 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tclk2: tcb0_tclk2-0 {
+ atmel,pins = <AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa0: tcb0_tioa0-0 {
+ atmel,pins = <AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa1: tcb0_tioa1-0 {
+ atmel,pins = <AT91_PIOC 29 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa2: tcb0_tioa2-0 {
+ atmel,pins = <AT91_PIOD 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob0: tcb0_tiob0-0 {
+ atmel,pins = <AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob1: tcb0_tiob1-0 {
+ atmel,pins = <AT91_PIOC 30 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob2: tcb0_tiob2-0 {
+ atmel,pins = <AT91_PIOD 11 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usart0 {
+ pinctrl_usart0: usart0-0 {
+ atmel,pins =
+ <AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_usart0_rts: usart0_rts-0 {
+ atmel,pins =
+ <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart0_cts: usart0_cts-0 {
+ atmel,pins =
+ <AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart0_dtr_dsr: usart0_dtr_dsr-0 {
+ atmel,pins =
+ <AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart0_dcd: usart0_dcd-0 {
+ atmel,pins =
+ <AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart0_ri: usart0_ri-0 {
+ atmel,pins =
+ <AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart0_sck: usart0_sck-0 {
+ atmel,pins =
+ <AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usart1 {
+ pinctrl_usart1: usart1-0 {
+ atmel,pins =
+ <AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart1_rts: usart1_rts-0 {
+ atmel,pins =
+ <AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart1_cts: usart1_cts-0 {
+ atmel,pins =
+ <AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart1_sck: usart1_sck-0 {
+ atmel,pins =
+ <AT91_PIOD 2 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usart2 {
+ pinctrl_usart2: usart2-0 {
+ atmel,pins =
+ <AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart2_rts: usart2_rts-0 {
+ atmel,pins =
+ <AT91_PIOA 29 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart2_cts: usart2_cts-0 {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart2_sck: usart2_sck-0 {
+ atmel,pins =
+ <AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usart3 {
+ pinctrl_usart3: usart3-0 {
+ atmel,pins =
+ <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+ <AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart3_rts: usart3_rts-0 {
+ atmel,pins =
+ <AT91_PIOD 4 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart3_cts: usart3_cts-0 {
+ atmel,pins =
+ <AT91_PIOD 3 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_usart3_sck: usart3_sck-0 {
+ atmel,pins =
+ <AT91_PIOA 20 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+ };
+
+ pioA: gpio@fffff400 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioA_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioB: gpio@fffff600 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioB_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioC: gpio@fffff800 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioC_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioD: gpio@fffffa00 {
+ compatible = "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioD_clk>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pmc: pmc@fffffc00 {
+ compatible = "atmel,at91sam9g45-pmc", "syscon";
+ reg = <0xfffffc00 0x100>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+ u-boot,dm-pre-reloc;
+
+ main: mainck {
+ compatible = "atmel,at91rm9200-clk-main";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCS>;
+ clocks = <&main_xtal>;
+ };
+
+ plla: pllack@0 {
+ compatible = "atmel,at91rm9200-clk-pll";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_LOCKA>;
+ clocks = <&main>;
+ reg = <0>;
+ atmel,clk-input-range = <1000000 32000000>;
+ #atmel,pll-clk-output-range-cells = <3>;
+ atmel,pll-clk-output-ranges = <80000000 200000000 0>,
+ <190000000 240000000 2>;
+ };
+
+ utmi: utmick {
+ compatible = "atmel,at91sam9x5-clk-utmi";
+ #clock-cells = <0>;
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_LOCKU>;
+ clocks = <&main>;
+ };
+
+ mck: masterck {
+ compatible = "atmel,at91rm9200-clk-master";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
+ clocks = <&clk32k>, <&main>, <&plla>, <&utmi>;
+ atmel,clk-output-range = <0 94000000>;
+ atmel,clk-divisors = <1 2 4 0>;
+ u-boot,dm-pre-reloc;
+ };
+
+ prog: progck {
+ compatible = "atmel,at91rm9200-clk-programmable";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&clk32k>, <&main>, <&plla>, <&utmi>, <&mck>;
+
+ prog0: prog@0 {
+ #clock-cells = <0>;
+ reg = <0>;
+ interrupts = <AT91_PMC_PCKRDY(0)>;
+ };
+
+ prog1: prog@1 {
+ #clock-cells = <0>;
+ reg = <1>;
+ interrupts = <AT91_PMC_PCKRDY(1)>;
+ };
+ };
+
+ systemck {
+ compatible = "atmel,at91rm9200-clk-system";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pck0: pck0@8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ clocks = <&prog0>;
+ };
+
+ pck1: pck1@9 {
+ #clock-cells = <0>;
+ reg = <9>;
+ clocks = <&prog1>;
+ };
+
+ };
+
+ periphck {
+ compatible = "atmel,at91rm9200-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mck>;
+ u-boot,dm-pre-reloc;
+
+ pioA_clk: pioA_clk@2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioB_clk: pioB_clk@3 {
+ #clock-cells = <0>;
+ reg = <3>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioC_clk: pioC_clk@4 {
+ #clock-cells = <0>;
+ reg = <4>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pioD_clk: pioD_clk@5 {
+ #clock-cells = <0>;
+ reg = <5>;
+ u-boot,dm-pre-reloc;
+ };
+
+ usart0_clk: usart0_clk@6 {
+ #clock-cells = <0>;
+ reg = <6>;
+ };
+
+ usart1_clk: usart1_clk@7 {
+ #clock-cells = <0>;
+ reg = <7>;
+ };
+
+ usart2_clk: usart2_clk@8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ };
+
+ usart3_clk: usart3_clk@9 {
+ #clock-cells = <0>;
+ reg = <9>;
+ };
+
+ mci0_clk: mci0_clk@10 {
+ #clock-cells = <0>;
+ reg = <10>;
+ };
+
+ twi0_clk: twi0_clk@11 {
+ #clock-cells = <0>;
+ reg = <11>;
+ };
+
+ twi1_clk: twi1_clk@12 {
+ #clock-cells = <0>;
+ reg = <12>;
+ };
+
+ spi0_clk: spi0_clk@13 {
+ #clock-cells = <0>;
+ reg = <13>;
+ };
+
+ ssc0_clk: ssc0_clk@14 {
+ #clock-cells = <0>;
+ reg = <14>;
+ };
+
+ ssc1_clk: ssc1_clk@15 {
+ #clock-cells = <0>;
+ reg = <15>;
+ };
+
+ tc0_clk: tc0_clk@16 {
+ #clock-cells = <0>;
+ reg = <16>;
+ };
+
+ tc1_clk: tc1_clk@17 {
+ #clock-cells = <0>;
+ reg = <17>;
+ };
+
+ tc2_clk: tc2_clk@18 {
+ #clock-cells = <0>;
+ reg = <18>;
+ };
+
+ pwm_clk: pwm_clk@19 {
+ #clock-cells = <0>;
+ reg = <19>;
+ };
+
+ adc_clk: adc_clk@20 {
+ #clock-cells = <0>;
+ reg = <20>;
+ };
+
+ dma0_clk: dma0_clk@21 {
+ #clock-cells = <0>;
+ reg = <21>;
+ };
+
+ udphs_clk: udphs_clk@22 {
+ #clock-cells = <0>;
+ reg = <22>;
+ };
+
+ lcd_clk: lcd_clk@23 {
+ #clock-cells = <0>;
+ reg = <23>;
+ };
+ };
+ };
+
+ rstc@fffffd00 {
+ compatible = "atmel,at91sam9260-rstc";
+ reg = <0xfffffd00 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ shdwc@fffffd10 {
+ compatible = "atmel,at91sam9260-shdwc";
+ reg = <0xfffffd10 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ pit: timer@fffffd30 {
+ compatible = "atmel,at91sam9260-pit";
+ reg = <0xfffffd30 0xf>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&mck>;
+ };
+
+ watchdog@fffffd40 {
+ compatible = "atmel,at91sam9260-wdt";
+ reg = <0xfffffd40 0x10>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ status = "disabled";
+ };
+
+ sckc@fffffd50 {
+ compatible = "atmel,at91sam9x5-sckc";
+ reg = <0xfffffd50 0x4>;
+
+ slow_osc: slow_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-osc";
+ #clock-cells = <0>;
+ atmel,startup-time-usec = <1200000>;
+ clocks = <&slow_xtal>;
+ };
+
+ slow_rc_osc: slow_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+ #clock-cells = <0>;
+ atmel,startup-time-usec = <75>;
+ clock-frequency = <32768>;
+ clock-accuracy = <50000000>;
+ };
+
+ clk32k: slck {
+ compatible = "atmel,at91sam9x5-clk-slow";
+ #clock-cells = <0>;
+ clocks = <&slow_rc_osc &slow_osc>;
+ };
+ };
+
+ rtc@fffffd20 {
+ compatible = "atmel,at91sam9260-rtt";
+ reg = <0xfffffd20 0x10>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ status = "disabled";
+ };
+
+ gpbr: syscon@fffffd60 {
+ compatible = "atmel,at91sam9260-gpbr", "syscon";
+ reg = <0xfffffd60 0x10>;
+ status = "disabled";
+ };
+
+ rtc@fffffe00 {
+ compatible = "atmel,at91rm9200-rtc";
+ reg = <0xfffffe00 0x40>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ status = "disabled";
+ };
+
+ };
+ };
+
+ i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&pioA 23 GPIO_ACTIVE_HIGH>, /* sda */
+ <&pioA 24 GPIO_ACTIVE_HIGH>; /* scl */
+ i2c-gpio,sda-open-drain;
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio0>;
+ status = "disabled";
+ };
+
+ i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ gpios = <&pioD 10 GPIO_ACTIVE_HIGH>, /* sda */
+ <&pioD 11 GPIO_ACTIVE_HIGH>; /* scl */
+ i2c-gpio,sda-open-drain;
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio1>;
+ status = "disabled";
+ };
+};
diff --git a/arch/arm/dts/at91sam9rlek.dts b/arch/arm/dts/at91sam9rlek.dts
new file mode 100644
index 0000000..ae42697
--- /dev/null
+++ b/arch/arm/dts/at91sam9rlek.dts
@@ -0,0 +1,239 @@
+/*
+ * at91sam9rlek.dts - Device Tree file for Atmel at91sam9rl reference board
+ *
+ * Copyright (C) 2014 Alexandre Belloni <alexandre.belloni@free-electrons.com>
+ *
+ * Licensed under GPLv2 only
+ */
+/dts-v1/;
+#include "at91sam9rl.dtsi"
+
+/ {
+ model = "Atmel at91sam9rlek";
+ compatible = "atmel,at91sam9rlek", "atmel,at91sam9rl", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "rootfstype=ubifs root=ubi0:rootfs ubi.mtd=5 rw";
+ stdout-path = "serial0:115200n8";
+ u-boot,dm-pre-reloc;
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ fb0: fb@00500000 {
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <1>;
+ atmel,lcd-wiring-mode = "RGB";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <4965000>;
+ hactive = <240>;
+ vactive = <320>;
+ hback-porch = <1>;
+ hfront-porch = <33>;
+ vback-porch = <1>;
+ vfront-porch = <0>;
+ hsync-len = <5>;
+ vsync-len = <1>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt = <1>;
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv@c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+
+ apb {
+ mmc0: mmc@fffa4000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot0_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ usart0: serial@fffb0000 {
+ pinctrl-0 = <
+ &pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts>;
+ status = "okay";
+ };
+
+ adc0: adc@fffd0000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad1
+ &pinctrl_adc0_ad2
+ &pinctrl_adc0_ad3
+ &pinctrl_adc0_ad4
+ &pinctrl_adc0_ad5
+ &pinctrl_adc0_adtrg>;
+ atmel,adc-ts-wires = <4>;
+ status = "okay";
+ };
+
+ usb0: gadget@fffd4000 {
+ atmel,vbus-gpio = <&pioA 8 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ spi0: spi@fffcc000 {
+ status = "okay";
+ cs-gpios = <&pioA 28 0>, <0>, <0>, <0>;
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <15000000>;
+ reg = <0>;
+ };
+ };
+
+ pwm0: pwm@fffc8000 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_pwm1_2>,
+ <&pinctrl_pwm0_pwm2_2>;
+ };
+
+ dbgu: serial@fffff200 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOA 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog@fffffd40 {
+ status = "okay";
+ };
+
+ rtc@fffffe00 {
+ status = "okay";
+ };
+ };
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ ds1 {
+ label = "ds1";
+ pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>;
+ max-brightness = <255>;
+ };
+
+ ds2 {
+ label = "ds2";
+ pwms = <&pwm0 2 5000 PWM_POLARITY_INVERTED>;
+ max-brightness = <255>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ds3 {
+ label = "ds3";
+ gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ right_click {
+ label = "right_click";
+ gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
+ linux,code = <273>;
+ wakeup-source;
+ };
+
+ left_click {
+ label = "left_click";
+ gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
+ linux,code = <272>;
+ wakeup-source;
+ };
+ };
+
+ i2c-gpio-0 {
+ status = "okay";
+ };
+
+ i2c-gpio-1 {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/dts/at91sam9x25.dtsi b/arch/arm/dts/at91sam9x25.dtsi
new file mode 100644
index 0000000..3c5fa33
--- /dev/null
+++ b/arch/arm/dts/at91sam9x25.dtsi
@@ -0,0 +1,32 @@
+/*
+ * at91sam9x25.dtsi - Device Tree Include file for AT91SAM9X25 SoC
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include "at91sam9x5.dtsi"
+#include "at91sam9x5_usart3.dtsi"
+#include "at91sam9x5_macb0.dtsi"
+#include "at91sam9x5_macb1.dtsi"
+#include "at91sam9x5_can.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9X25 SoC";
+ compatible = "atmel,at91sam9x25", "atmel,at91sam9x5";
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe03fff 0xc000001c /* pioA */
+ 0x0007ffff 0x00047e3f 0x00000000 /* pioB */
+ 0x80000000 0xfffd0000 0xb83fffff /* pioC */
+ 0x003fffff 0x003f8000 0x00000000 /* pioD */
+ >;
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x25ek.dts b/arch/arm/dts/at91sam9x25ek.dts
new file mode 100644
index 0000000..4948648
--- /dev/null
+++ b/arch/arm/dts/at91sam9x25ek.dts
@@ -0,0 +1,30 @@
+/*
+ * at91sam9x25ek.dts - Device Tree file for AT91SAM9X25-EK board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9x25.dtsi"
+#include "at91sam9x5ek.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9X25-EK";
+ compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+ ahb {
+ apb {
+ macb0: ethernet@f802c000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ macb1: ethernet@f8030000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x35.dtsi b/arch/arm/dts/at91sam9x35.dtsi
new file mode 100644
index 0000000..d9054e8
--- /dev/null
+++ b/arch/arm/dts/at91sam9x35.dtsi
@@ -0,0 +1,31 @@
+/*
+ * at91sam9x35.dtsi - Device Tree Include file for AT91SAM9X35 SoC
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include "at91sam9x5.dtsi"
+#include "at91sam9x5_lcd.dtsi"
+#include "at91sam9x5_macb0.dtsi"
+#include "at91sam9x5_can.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9X35 SoC";
+ compatible = "atmel,at91sam9x35", "atmel,at91sam9x5";
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe03fff 0xc000000c /* pioA */
+ 0x000406ff 0x00047e3f 0x00000000 /* pioB */
+ 0xfdffffff 0x00000000 0xb83fffff /* pioC */
+ 0x003fffff 0x003f8000 0x00000000 /* pioD */
+ >;
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x35ek.dts b/arch/arm/dts/at91sam9x35ek.dts
new file mode 100644
index 0000000..3ca70c0
--- /dev/null
+++ b/arch/arm/dts/at91sam9x35ek.dts
@@ -0,0 +1,30 @@
+/*
+ * at91sam9x35ek.dts - Device Tree file for AT91SAM9X35-EK board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9x35.dtsi"
+#include "at91sam9x5dm.dtsi"
+#include "at91sam9x5ek.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9X35-EK";
+ compatible = "atmel,at91sam9x35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+ ahb {
+ apb {
+ macb0: ethernet@f802c000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+ hlcdc: hlcdc@f8038000 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5.dtsi b/arch/arm/dts/at91sam9x5.dtsi
new file mode 100644
index 0000000..a422c98
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5.dtsi
@@ -0,0 +1,1302 @@
+/*
+ * at91sam9x5.dtsi - Device Tree Include file for AT91SAM9x5 family SoC
+ * applies to AT91SAM9G15, AT91SAM9G25, AT91SAM9G35,
+ * AT91SAM9X25, AT91SAM9X35 SoC
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/at91.h>
+
+/ {
+ model = "Atmel AT91SAM9x5 family SoC";
+ compatible = "atmel,at91sam9x5";
+ interrupt-parent = <&aic>;
+
+ aliases {
+ serial0 = &dbgu;
+ serial1 = &usart0;
+ serial2 = &usart1;
+ serial3 = &usart2;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ tcb0 = &tcb0;
+ tcb1 = &tcb1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ ssc0 = &ssc0;
+ pwm0 = &pwm0;
+ spi0 = &spi0;
+ };
+
+ cpus {
+ #address-cells = <0>;
+ #size-cells = <0>;
+
+ cpu {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ };
+ };
+
+ memory {
+ reg = <0x20000000 0x10000000>;
+ };
+
+ clocks {
+ slow_xtal: slow_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ main_xtal: main_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ adc_op_clk: adc_op_clk{
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1000000>;
+ };
+ };
+
+ sram: sram@00300000 {
+ compatible = "mmio-sram";
+ reg = <0x00300000 0x8000>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ u-boot,dm-pre-reloc;
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ u-boot,dm-pre-reloc;
+
+ aic: interrupt-controller@fffff000 {
+ #interrupt-cells = <3>;
+ compatible = "atmel,at91rm9200-aic";
+ interrupt-controller;
+ reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <31>;
+ };
+
+ ramc0: ramc@ffffe800 {
+ compatible = "atmel,at91sam9g45-ddramc";
+ reg = <0xffffe800 0x200>;
+ clocks = <&ddrck>;
+ clock-names = "ddrck";
+ };
+
+ pmc: pmc@fffffc00 {
+ compatible = "atmel,at91sam9x5-pmc", "syscon";
+ reg = <0xfffffc00 0x200>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+ u-boot,dm-pre-reloc;
+
+ main_rc_osc: main_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-main-rc-osc";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCRCS>;
+ clock-frequency = <12000000>;
+ clock-accuracy = <50000000>;
+ };
+
+ main_osc: main_osc {
+ compatible = "atmel,at91rm9200-clk-main-osc";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCS>;
+ clocks = <&main_xtal>;
+ };
+
+ main: mainck {
+ compatible = "atmel,at91sam9x5-clk-main";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCSELS>;
+ clocks = <&main_rc_osc>, <&main_osc>;
+ };
+
+ plla: pllack@0 {
+ compatible = "atmel,at91rm9200-clk-pll";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_LOCKA>;
+ clocks = <&main>;
+ reg = <0>;
+ atmel,clk-input-range = <2000000 32000000>;
+ #atmel,pll-clk-output-range-cells = <4>;
+ atmel,pll-clk-output-ranges = <745000000 800000000 0 0
+ 695000000 750000000 1 0
+ 645000000 700000000 2 0
+ 595000000 650000000 3 0
+ 545000000 600000000 0 1
+ 495000000 555000000 1 1
+ 445000000 500000000 2 1
+ 400000000 450000000 3 1>;
+ };
+
+ plladiv: plladivck {
+ compatible = "atmel,at91sam9x5-clk-plldiv";
+ #clock-cells = <0>;
+ clocks = <&plla>;
+ };
+
+ utmi: utmick {
+ compatible = "atmel,at91sam9x5-clk-utmi";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_LOCKU>;
+ clocks = <&main>;
+ };
+
+ mck: masterck {
+ compatible = "atmel,at91sam9x5-clk-master";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
+ atmel,clk-output-range = <0 133333333>;
+ atmel,clk-divisors = <1 2 4 3>;
+ atmel,master-clk-have-div3-pres;
+ u-boot,dm-pre-reloc;
+
+ };
+
+ usb: usbck {
+ compatible = "atmel,at91sam9x5-clk-usb";
+ #clock-cells = <0>;
+ clocks = <&plladiv>, <&utmi>;
+ };
+
+ prog: progck {
+ compatible = "atmel,at91sam9x5-clk-programmable";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+ prog0: prog@0 {
+ #clock-cells = <0>;
+ reg = <0>;
+ interrupts = <AT91_PMC_PCKRDY(0)>;
+ };
+
+ prog1: prog@1 {
+ #clock-cells = <0>;
+ reg = <1>;
+ interrupts = <AT91_PMC_PCKRDY(1)>;
+ };
+ };
+
+ smd: smdclk {
+ compatible = "atmel,at91sam9x5-clk-smd";
+ #clock-cells = <0>;
+ clocks = <&plladiv>, <&utmi>;
+ };
+
+ systemck {
+ compatible = "atmel,at91rm9200-clk-system";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ddrck: ddrck@2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ clocks = <&mck>;
+ };
+
+ smdck: smdck@4 {
+ #clock-cells = <0>;
+ reg = <4>;
+ clocks = <&smd>;
+ };
+
+ uhpck: uhpck@6 {
+ #clock-cells = <0>;
+ reg = <6>;
+ clocks = <&usb>;
+ };
+
+ udpck: udpck@7 {
+ #clock-cells = <0>;
+ reg = <7>;
+ clocks = <&usb>;
+ };
+
+ pck0: pck0@8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ clocks = <&prog0>;
+ };
+
+ pck1: pck1@9 {
+ #clock-cells = <0>;
+ reg = <9>;
+ clocks = <&prog1>;
+ };
+ };
+
+ periphck {
+ compatible = "atmel,at91sam9x5-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mck>;
+ u-boot,dm-pre-reloc;
+
+
+ pioAB_clk: pioAB_clk@2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ };
+
+ pioCD_clk: pioCD_clk@3 {
+ #clock-cells = <0>;
+ reg = <3>;
+ };
+
+ smd_clk: smd_clk@4 {
+ #clock-cells = <0>;
+ reg = <4>;
+ };
+
+ usart0_clk: usart0_clk@5 {
+ #clock-cells = <0>;
+ reg = <5>;
+ };
+
+ usart1_clk: usart1_clk@6 {
+ #clock-cells = <0>;
+ reg = <6>;
+ };
+
+ usart2_clk: usart2_clk@7 {
+ #clock-cells = <0>;
+ reg = <7>;
+ };
+
+ twi0_clk: twi0_clk@9 {
+ reg = <9>;
+ #clock-cells = <0>;
+ };
+
+ twi1_clk: twi1_clk@10 {
+ #clock-cells = <0>;
+ reg = <10>;
+ };
+
+ twi2_clk: twi2_clk@11 {
+ #clock-cells = <0>;
+ reg = <11>;
+ };
+
+ mci0_clk: mci0_clk@12 {
+ #clock-cells = <0>;
+ reg = <12>;
+ };
+
+ spi0_clk: spi0_clk@13 {
+ #clock-cells = <0>;
+ reg = <13>;
+ };
+
+ spi1_clk: spi1_clk@14 {
+ #clock-cells = <0>;
+ reg = <14>;
+ };
+
+ uart0_clk: uart0_clk@15 {
+ #clock-cells = <0>;
+ reg = <15>;
+ };
+
+ uart1_clk: uart1_clk@16 {
+ #clock-cells = <0>;
+ reg = <16>;
+ };
+
+ tcb0_clk: tcb0_clk@17 {
+ #clock-cells = <0>;
+ reg = <17>;
+ };
+
+ pwm_clk: pwm_clk@18 {
+ #clock-cells = <0>;
+ reg = <18>;
+ };
+
+ adc_clk: adc_clk@19 {
+ #clock-cells = <0>;
+ reg = <19>;
+ };
+
+ dma0_clk: dma0_clk@20 {
+ #clock-cells = <0>;
+ reg = <20>;
+ };
+
+ dma1_clk: dma1_clk@21 {
+ #clock-cells = <0>;
+ reg = <21>;
+ };
+
+ uhphs_clk: uhphs_clk@22 {
+ #clock-cells = <0>;
+ reg = <22>;
+ };
+
+ udphs_clk: udphs_clk@23 {
+ #clock-cells = <0>;
+ reg = <23>;
+ };
+
+ mci1_clk: mci1_clk@26 {
+ #clock-cells = <0>;
+ reg = <26>;
+ };
+
+ ssc0_clk: ssc0_clk@28 {
+ #clock-cells = <0>;
+ reg = <28>;
+ };
+ };
+ };
+
+ rstc@fffffe00 {
+ compatible = "atmel,at91sam9g45-rstc";
+ reg = <0xfffffe00 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ shdwc@fffffe10 {
+ compatible = "atmel,at91sam9x5-shdwc";
+ reg = <0xfffffe10 0x10>;
+ clocks = <&clk32k>;
+ };
+
+ pit: timer@fffffe30 {
+ compatible = "atmel,at91sam9260-pit";
+ reg = <0xfffffe30 0xf>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&mck>;
+ };
+
+ sckc@fffffe50 {
+ compatible = "atmel,at91sam9x5-sckc";
+ reg = <0xfffffe50 0x4>;
+
+ slow_osc: slow_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-osc";
+ #clock-cells = <0>;
+ clocks = <&slow_xtal>;
+ };
+
+ slow_rc_osc: slow_rc_osc {
+ compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-accuracy = <50000000>;
+ };
+
+ clk32k: slck {
+ compatible = "atmel,at91sam9x5-clk-slow";
+ #clock-cells = <0>;
+ clocks = <&slow_rc_osc>, <&slow_osc>;
+ };
+ };
+
+ tcb0: timer@f8008000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xf8008000 0x100>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tcb0_clk>, <&clk32k>;
+ clock-names = "t0_clk", "slow_clk";
+ };
+
+ tcb1: timer@f800c000 {
+ compatible = "atmel,at91sam9x5-tcb";
+ reg = <0xf800c000 0x100>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tcb0_clk>, <&clk32k>;
+ clock-names = "t0_clk", "slow_clk";
+ };
+
+ dma0: dma-controller@ffffec00 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffec00 0x200>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <2>;
+ clocks = <&dma0_clk>;
+ clock-names = "dma_clk";
+ };
+
+ dma1: dma-controller@ffffee00 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffee00 0x200>;
+ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <2>;
+ clocks = <&dma1_clk>;
+ clock-names = "dma_clk";
+ };
+
+ pinctrl@fffff400 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+ ranges = <0xfffff400 0xfffff400 0x800>;
+ reg = <0xfffff400 0x200 /* pioA */
+ 0xfffff600 0x200 /* pioB */
+ 0xfffff800 0x200 /* pioC */
+ 0xfffffa00 0x200 /* pioD */
+ >;
+ u-boot,dm-pre-reloc;
+
+
+ /* shared pinctrl settings */
+ dbgu {
+ u-boot,dm-pre-reloc;
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins =
+ <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usart0 {
+ pinctrl_usart0: usart0-0 {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA0 periph A with pullup */
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA1 periph A */
+ };
+
+ pinctrl_usart0_rts: usart0_rts-0 {
+ atmel,pins =
+ <AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA2 periph A */
+ };
+
+ pinctrl_usart0_cts: usart0_cts-0 {
+ atmel,pins =
+ <AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA3 periph A */
+ };
+
+ pinctrl_usart0_sck: usart0_sck-0 {
+ atmel,pins =
+ <AT91_PIOA 4 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA4 periph A */
+ };
+ };
+
+ usart1 {
+ pinctrl_usart1: usart1-0 {
+ atmel,pins =
+ <AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA5 periph A with pullup */
+ AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA6 periph A */
+ };
+
+ pinctrl_usart1_rts: usart1_rts-0 {
+ atmel,pins =
+ <AT91_PIOC 27 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC27 periph C */
+ };
+
+ pinctrl_usart1_cts: usart1_cts-0 {
+ atmel,pins =
+ <AT91_PIOC 28 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC28 periph C */
+ };
+
+ pinctrl_usart1_sck: usart1_sck-0 {
+ atmel,pins =
+ <AT91_PIOC 29 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC29 periph C */
+ };
+ };
+
+ usart2 {
+ pinctrl_usart2: usart2-0 {
+ atmel,pins =
+ <AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA7 periph A with pullup */
+ AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA8 periph A */
+ };
+
+ pinctrl_usart2_rts: usart2_rts-0 {
+ atmel,pins =
+ <AT91_PIOB 0 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB0 periph B */
+ };
+
+ pinctrl_usart2_cts: usart2_cts-0 {
+ atmel,pins =
+ <AT91_PIOB 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB1 periph B */
+ };
+
+ pinctrl_usart2_sck: usart2_sck-0 {
+ atmel,pins =
+ <AT91_PIOB 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB2 periph B */
+ };
+ };
+
+ uart0 {
+ pinctrl_uart0: uart0-0 {
+ atmel,pins =
+ <AT91_PIOC 8 AT91_PERIPH_C AT91_PINCTRL_NONE /* PC8 periph C */
+ AT91_PIOC 9 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>; /* PC9 periph C with pullup */
+ };
+ };
+
+ uart1 {
+ pinctrl_uart1: uart1-0 {
+ atmel,pins =
+ <AT91_PIOC 16 AT91_PERIPH_C AT91_PINCTRL_NONE /* PC16 periph C */
+ AT91_PIOC 17 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>; /* PC17 periph C with pullup */
+ };
+ };
+
+ nand {
+ pinctrl_nand: nand-0 {
+ atmel,pins =
+ <AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD0 periph A Read Enable */
+ AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD1 periph A Write Enable */
+ AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD2 periph A Address Latch Enable */
+ AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD3 periph A Command Latch Enable */
+ AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PD4 gpio Chip Enable pin pull_up */
+ AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PD5 gpio RDY/BUSY pin pull_up */
+ AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD6 periph A Data bit 0 */
+ AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD7 periph A Data bit 1 */
+ AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD8 periph A Data bit 2 */
+ AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD9 periph A Data bit 3 */
+ AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD10 periph A Data bit 4 */
+ AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD11 periph A Data bit 5 */
+ AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD12 periph A Data bit 6 */
+ AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD13 periph A Data bit 7 */
+ };
+
+ pinctrl_nand_16bits: nand_16bits-0 {
+ atmel,pins =
+ <AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD14 periph A Data bit 8 */
+ AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD15 periph A Data bit 9 */
+ AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD16 periph A Data bit 10 */
+ AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD17 periph A Data bit 11 */
+ AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD18 periph A Data bit 12 */
+ AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD19 periph A Data bit 13 */
+ AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* PD20 periph A Data bit 14 */
+ AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PD21 periph A Data bit 15 */
+ };
+ };
+
+ mmc0 {
+ pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 {
+ atmel,pins =
+ <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA17 periph A */
+ AT91_PIOA 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA16 periph A with pullup */
+ AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA15 periph A with pullup */
+ };
+
+ pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 {
+ atmel,pins =
+ <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA18 periph A with pullup */
+ AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PA19 periph A with pullup */
+ AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA20 periph A with pullup */
+ };
+ };
+
+ mmc1 {
+ pinctrl_mmc1_slot0_clk_cmd_dat0: mmc1_slot0_clk_cmd_dat0-0 {
+ atmel,pins =
+ <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA13 periph B */
+ AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA12 periph B with pullup */
+ AT91_PIOA 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA11 periph B with pullup */
+ };
+
+ pinctrl_mmc1_slot0_dat1_3: mmc1_slot0_dat1_3-0 {
+ atmel,pins =
+ <AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA2 periph B with pullup */
+ AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA3 periph B with pullup */
+ AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA4 periph B with pullup */
+ };
+ };
+
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins =
+ <AT91_PIOA 24 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA24 periph B */
+ AT91_PIOA 25 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA25 periph B */
+ AT91_PIOA 26 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA26 periph B */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins =
+ <AT91_PIOA 27 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA27 periph B */
+ AT91_PIOA 28 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA28 periph B */
+ AT91_PIOA 29 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA29 periph B */
+ };
+ };
+
+ spi0 {
+ pinctrl_spi0: spi0-0 {
+ atmel,pins =
+ <AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA11 periph A SPI0_MISO pin */
+ AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA12 periph A SPI0_MOSI pin */
+ AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA13 periph A SPI0_SPCK pin */
+ };
+ };
+
+ spi1 {
+ pinctrl_spi1: spi1-0 {
+ atmel,pins =
+ <AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA21 periph B SPI1_MISO pin */
+ AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA22 periph B SPI1_MOSI pin */
+ AT91_PIOA 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA23 periph B SPI1_SPCK pin */
+ };
+ };
+
+ i2c0 {
+ pinctrl_i2c0: i2c0-0 {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE /* PA30 periph A I2C0 data */
+ AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA31 periph A I2C0 clock */
+ };
+ };
+
+ i2c1 {
+ pinctrl_i2c1: i2c1-0 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE /* PC0 periph C I2C1 data */
+ AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* PC1 periph C I2C1 clock */
+ };
+ };
+
+ i2c2 {
+ pinctrl_i2c2: i2c2-0 {
+ atmel,pins =
+ <AT91_PIOB 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* PB4 periph B I2C2 data */
+ AT91_PIOB 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PB5 periph B I2C2 clock */
+ };
+ };
+
+ i2c_gpio0 {
+ pinctrl_i2c_gpio0: i2c_gpio0-0 {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE /* PA30 gpio multidrive I2C0 data */
+ AT91_PIOA 31 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; /* PA31 gpio multidrive I2C0 clock */
+ };
+ };
+
+ i2c_gpio1 {
+ pinctrl_i2c_gpio1: i2c_gpio1-0 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE /* PC0 gpio multidrive I2C1 data */
+ AT91_PIOC 1 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; /* PC1 gpio multidrive I2C1 clock */
+ };
+ };
+
+ i2c_gpio2 {
+ pinctrl_i2c_gpio2: i2c_gpio2-0 {
+ atmel,pins =
+ <AT91_PIOB 4 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE /* PB4 gpio multidrive I2C2 data */
+ AT91_PIOB 5 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; /* PB5 gpio multidrive I2C2 clock */
+ };
+ };
+
+ pwm0 {
+ pinctrl_pwm0_pwm0_0: pwm0_pwm0-0 {
+ atmel,pins =
+ <AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ pinctrl_pwm0_pwm0_1: pwm0_pwm0-1 {
+ atmel,pins =
+ <AT91_PIOC 10 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ pinctrl_pwm0_pwm0_2: pwm0_pwm0-2 {
+ atmel,pins =
+ <AT91_PIOC 18 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm1_0: pwm0_pwm1-0 {
+ atmel,pins =
+ <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ pinctrl_pwm0_pwm1_1: pwm0_pwm1-1 {
+ atmel,pins =
+ <AT91_PIOC 11 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ pinctrl_pwm0_pwm1_2: pwm0_pwm1-2 {
+ atmel,pins =
+ <AT91_PIOC 19 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm2_0: pwm0_pwm2-0 {
+ atmel,pins =
+ <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ pinctrl_pwm0_pwm2_1: pwm0_pwm2-1 {
+ atmel,pins =
+ <AT91_PIOC 20 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_pwm3_0: pwm0_pwm3-0 {
+ atmel,pins =
+ <AT91_PIOB 14 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ pinctrl_pwm0_pwm3_1: pwm0_pwm3-1 {
+ atmel,pins =
+ <AT91_PIOC 21 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ };
+
+ tcb0 {
+ pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
+ atmel,pins = <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tclk1: tcb0_tclk1-0 {
+ atmel,pins = <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tclk2: tcb0_tclk2-0 {
+ atmel,pins = <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa0: tcb0_tioa0-0 {
+ atmel,pins = <AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa1: tcb0_tioa1-0 {
+ atmel,pins = <AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tioa2: tcb0_tioa2-0 {
+ atmel,pins = <AT91_PIOA 23 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob0: tcb0_tiob0-0 {
+ atmel,pins = <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob1: tcb0_tiob1-0 {
+ atmel,pins = <AT91_PIOA 28 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb0_tiob2: tcb0_tiob2-0 {
+ atmel,pins = <AT91_PIOA 29 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ tcb1 {
+ pinctrl_tcb1_tclk0: tcb1_tclk0-0 {
+ atmel,pins = <AT91_PIOC 4 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tclk1: tcb1_tclk1-0 {
+ atmel,pins = <AT91_PIOC 7 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tclk2: tcb1_tclk2-0 {
+ atmel,pins = <AT91_PIOC 14 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tioa0: tcb1_tioa0-0 {
+ atmel,pins = <AT91_PIOC 2 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tioa1: tcb1_tioa1-0 {
+ atmel,pins = <AT91_PIOC 5 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tioa2: tcb1_tioa2-0 {
+ atmel,pins = <AT91_PIOC 12 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tiob0: tcb1_tiob0-0 {
+ atmel,pins = <AT91_PIOC 3 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tiob1: tcb1_tiob1-0 {
+ atmel,pins = <AT91_PIOC 6 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_tcb1_tiob2: tcb1_tiob2-0 {
+ atmel,pins = <AT91_PIOC 13 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ };
+ };
+
+ pioA: gpio@fffff400 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioAB_clk>;
+ };
+
+ pioB: gpio@fffff600 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #gpio-lines = <19>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioAB_clk>;
+ };
+
+ pioC: gpio@fffff800 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioCD_clk>;
+ };
+
+ pioD: gpio@fffffa00 {
+ compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #gpio-lines = <22>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pioCD_clk>;
+ };
+
+ ssc0: ssc@f0010000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xf0010000 0x4000>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(13)>,
+ <&dma0 1 AT91_DMA_CFG_PER_ID(14)>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ clocks = <&ssc0_clk>;
+ clock-names = "pclk";
+ status = "disabled";
+ };
+
+ mmc0: mmc@f0008000 {
+ compatible = "atmel,hsmci";
+ reg = <0xf0008000 0x600>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(0)>;
+ dma-names = "rxtx";
+ pinctrl-names = "default";
+ clocks = <&mci0_clk>;
+ clock-names = "mci_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ mmc1: mmc@f000c000 {
+ compatible = "atmel,hsmci";
+ reg = <0xf000c000 0x600>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(0)>;
+ dma-names = "rxtx";
+ pinctrl-names = "default";
+ clocks = <&mci1_clk>;
+ clock-names = "mci_clk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ dbgu: serial@fffff200 {
+ compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0xfffff200 0x200>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(8)>,
+ <&dma1 1 (AT91_DMA_CFG_PER_ID(9) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+ dma-names = "tx", "rx";
+ clocks = <&mck>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart0: serial@f801c000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf801c000 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart0>;
+ dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(3)>,
+ <&dma0 1 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+ dma-names = "tx", "rx";
+ clocks = <&usart0_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart1: serial@f8020000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8020000 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1>;
+ dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(5)>,
+ <&dma0 1 (AT91_DMA_CFG_PER_ID(6) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+ dma-names = "tx", "rx";
+ clocks = <&usart1_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ usart2: serial@f8024000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8024000 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart2>;
+ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(12)>,
+ <&dma1 1 (AT91_DMA_CFG_PER_ID(13) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+ dma-names = "tx", "rx";
+ clocks = <&usart2_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ i2c0: i2c@f8010000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf8010000 0x100>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(7)>,
+ <&dma0 1 AT91_DMA_CFG_PER_ID(8)>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ clocks = <&twi0_clk>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@f8014000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf8014000 0x100>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(5)>,
+ <&dma1 1 AT91_DMA_CFG_PER_ID(6)>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clocks = <&twi1_clk>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@f8018000 {
+ compatible = "atmel,at91sam9x5-i2c";
+ reg = <0xf8018000 0x100>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
+ dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(9)>,
+ <&dma0 1 AT91_DMA_CFG_PER_ID(10)>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clocks = <&twi2_clk>;
+ status = "disabled";
+ };
+
+ uart0: serial@f8040000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8040000 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ clocks = <&uart0_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ uart1: serial@f8044000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8044000 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ clocks = <&uart1_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ adc0: adc@f804c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91sam9x5-adc";
+ reg = <0xf804c000 0x100>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&adc_clk>,
+ <&adc_op_clk>;
+ clock-names = "adc_clk", "adc_op_clk";
+ atmel,adc-use-external-triggers;
+ atmel,adc-channels-used = <0xffff>;
+ atmel,adc-vref = <3300>;
+ atmel,adc-startup-time = <40>;
+ atmel,adc-sample-hold-time = <11>;
+ atmel,adc-res = <8 10>;
+ atmel,adc-res-names = "lowres", "highres";
+ atmel,adc-use-res = "highres";
+
+ trigger0 {
+ trigger-name = "external-rising";
+ trigger-value = <0x1>;
+ trigger-external;
+ };
+
+ trigger1 {
+ trigger-name = "external-falling";
+ trigger-value = <0x2>;
+ trigger-external;
+ };
+
+ trigger2 {
+ trigger-name = "external-any";
+ trigger-value = <0x3>;
+ trigger-external;
+ };
+
+ trigger3 {
+ trigger-name = "continuous";
+ trigger-value = <0x6>;
+ };
+ };
+
+ spi0: spi@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xf0000000 0x100>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
+ dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(1)>,
+ <&dma0 1 AT91_DMA_CFG_PER_ID(2)>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0>;
+ clocks = <&spi0_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ spi1: spi@f0004000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0xf0004000 0x100>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 3>;
+ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(1)>,
+ <&dma1 1 AT91_DMA_CFG_PER_ID(2)>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1>;
+ clocks = <&spi1_clk>;
+ clock-names = "spi_clk";
+ status = "disabled";
+ };
+
+ usb2: gadget@f803c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91sam9g45-udc";
+ reg = <0x00500000 0x80000
+ 0xf803c000 0x400>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&utmi>, <&udphs_clk>;
+ clock-names = "hclk", "pclk";
+ status = "disabled";
+
+ ep@0 {
+ reg = <0>;
+ atmel,fifo-size = <64>;
+ atmel,nb-banks = <1>;
+ };
+
+ ep@1 {
+ reg = <1>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep@2 {
+ reg = <2>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <2>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep@3 {
+ reg = <3>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ };
+
+ ep@4 {
+ reg = <4>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ };
+
+ ep@5 {
+ reg = <5>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+
+ ep@6 {
+ reg = <6>;
+ atmel,fifo-size = <1024>;
+ atmel,nb-banks = <3>;
+ atmel,can-dma;
+ atmel,can-isoc;
+ };
+ };
+
+ watchdog@fffffe40 {
+ compatible = "atmel,at91sam9260-wdt";
+ reg = <0xfffffe40 0x10>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ atmel,watchdog-type = "hardware";
+ atmel,reset-type = "all";
+ atmel,dbg-halt;
+ status = "disabled";
+ };
+
+ rtc@fffffeb0 {
+ compatible = "atmel,at91sam9x5-rtc";
+ reg = <0xfffffeb0 0x40>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ status = "disabled";
+ };
+
+ pwm0: pwm@f8034000 {
+ compatible = "atmel,at91sam9rl-pwm";
+ reg = <0xf8034000 0x300>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
+ clocks = <&pwm_clk>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+ };
+
+ nand0: nand@40000000 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x40000000 0x10000000
+ 0xffffe000 0x600 /* PMECC Registers */
+ 0xffffe600 0x200 /* PMECC Error Location Registers */
+ 0x00108000 0x18000 /* PMECC looup table in ROM code */
+ >;
+ atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
+ atmel,nand-addr-offset = <21>;
+ atmel,nand-cmd-offset = <22>;
+ atmel,nand-has-dma;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand>;
+ gpios = <&pioD 5 GPIO_ACTIVE_HIGH
+ &pioD 4 GPIO_ACTIVE_HIGH
+ 0
+ >;
+ status = "disabled";
+ };
+
+ usb0: ohci@00600000 {
+ compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+ reg = <0x00600000 0x100000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+ clock-names = "ohci_clk", "hclk", "uhpck";
+ status = "disabled";
+ };
+
+ usb1: ehci@00700000 {
+ compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+ reg = <0x00700000 0x100000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&utmi>, <&uhphs_clk>;
+ clock-names = "usb_clk", "ehci_clk";
+ status = "disabled";
+ };
+ };
+
+ i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
+ &pioA 31 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,sda-open-drain;
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio0>;
+ status = "disabled";
+ };
+
+ i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ gpios = <&pioC 0 GPIO_ACTIVE_HIGH /* sda */
+ &pioC 1 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,sda-open-drain;
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio1>;
+ status = "disabled";
+ };
+
+ i2c-gpio-2 {
+ compatible = "i2c-gpio";
+ gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
+ &pioB 5 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,sda-open-drain;
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio2>;
+ status = "disabled";
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5_can.dtsi b/arch/arm/dts/at91sam9x5_can.dtsi
new file mode 100644
index 0000000..9727b77
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5_can.dtsi
@@ -0,0 +1,71 @@
+/*
+ * at91sam9x5_can.dtsi - Device Tree Include file for AT91SAM9x5 SoC with 1
+ * Ethernet interface.
+ *
+ * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ ahb {
+ apb {
+ pmc: pmc@fffffc00 {
+ periphck {
+ can0_clk: can0_clk@29 {
+ #clock-cells = <0>;
+ reg = <29>;
+ };
+
+ can1_clk: can1_clk@30 {
+ #clock-cells = <0>;
+ reg = <30>;
+ };
+ };
+ };
+
+ can0: can@f8000000 {
+ compatible = "atmel,at91sam9x5-can";
+ reg = <0xf8000000 0x300>;
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_rx_tx>;
+ clocks = <&can0_clk>;
+ clock-names = "can_clk";
+ status = "disabled";
+ };
+
+ can1: can@f8004000 {
+ compatible = "atmel,at91sam9x5-can";
+ reg = <0xf8004000 0x300>;
+ interrupts = <30 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_rx_tx>;
+ clocks = <&can1_clk>;
+ clock-names = "can_clk";
+ status = "disabled";
+ };
+
+ pinctrl@fffff400 {
+ can0 {
+ pinctrl_can0_rx_tx: can0_rx_tx {
+ atmel,pins =
+ <AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX0, conflicts with DRXD */
+ AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* CANTX0, conflicts with DTXD */
+ };
+ };
+
+ can1 {
+ pinctrl_can1_rx_tx: can1_rx_tx {
+ atmel,pins =
+ <AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX1, conflicts with RXD1 */
+ AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* CANTX1, conflicts with TXD1 */
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5_isi.dtsi b/arch/arm/dts/at91sam9x5_isi.dtsi
new file mode 100644
index 0000000..2c5075f
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5_isi.dtsi
@@ -0,0 +1,72 @@
+/*
+ * at91sam9x5_isi.dtsi - Device Tree Include file for AT91SAM9x5 SoC with an
+ * Image Sensor Interface.
+ *
+ * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ isi {
+ pinctrl_isi_data_0_7: isi-0-data-0-7 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D0, conflicts with LCDDAT0 */
+ AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D1, conflicts with LCDDAT1 */
+ AT91_PIOC 2 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D2, conflicts with LCDDAT2 */
+ AT91_PIOC 3 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D3, conflicts with LCDDAT3 */
+ AT91_PIOC 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D4, conflicts with LCDDAT4 */
+ AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D5, conflicts with LCDDAT5 */
+ AT91_PIOC 6 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D6, conflicts with LCDDAT6 */
+ AT91_PIOC 7 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D7, conflicts with LCDDAT7 */
+ AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_PCK, conflicts with LCDDAT12 */
+ AT91_PIOC 14 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_HSYNC, conflicts with LCDDAT14 */
+ AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* ISI_VSYNC, conflicts with LCDDAT13 */
+ };
+
+ pinctrl_isi_data_8_9: isi-0-data-8-9 {
+ atmel,pins =
+ <AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D8, conflicts with LCDDAT8 */
+ AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* ISI_D9, conflicts with LCDDAT9 */
+ };
+
+ pinctrl_isi_data_10_11: isi-0-data-10-11 {
+ atmel,pins =
+ <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D10, conflicts with LCDDAT10 */
+ AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* ISI_D11, conflicts with LCDDAT11 */
+ };
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ periphck {
+ isi_clk: isi_clk@25 {
+ #clock-cells = <0>;
+ reg = <25>;
+ };
+ };
+ };
+
+ isi: isi@f8048000 {
+ compatible = "atmel,at91sam9g45-isi";
+ reg = <0xf8048000 0x4000>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isi_data_0_7>;
+ clocks = <&isi_clk>;
+ clock-names = "isi_clk";
+ status = "disabled";
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5_lcd.dtsi b/arch/arm/dts/at91sam9x5_lcd.dtsi
new file mode 100644
index 0000000..96b7095
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5_lcd.dtsi
@@ -0,0 +1,146 @@
+/*
+ * at91sam9x5_lcd.dtsi - Device Tree Include file for AT91SAM9x5 SoC with an
+ * LCD controller.
+ *
+ * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ ahb {
+ apb {
+ hlcdc: hlcdc@f8038000 {
+ compatible = "atmel,at91sam9x5-hlcdc";
+ reg = <0xf8038000 0x4000>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+ clock-names = "periph_clk","sys_clk", "slow_clk";
+ status = "disabled";
+ };
+
+ pinctrl@fffff400 {
+ lcd {
+ pinctrl_lcd_base: lcd-base-0 {
+ atmel,pins =
+ <AT91_PIOC 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDVSYNC */
+ AT91_PIOC 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDHSYNC */
+ AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDDISP */
+ AT91_PIOC 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDDEN */
+ AT91_PIOC 30 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDPCK */
+ };
+
+ pinctrl_lcd_pwm: lcd-pwm-0 {
+ atmel,pins = <AT91_PIOC 26 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDPWM */
+ };
+
+ pinctrl_lcd_rgb444: lcd-rgb-0 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOC 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD11 pin */
+ };
+
+ pinctrl_lcd_rgb565: lcd-rgb-1 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOC 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD15 pin */
+ };
+
+ pinctrl_lcd_rgb666: lcd-rgb-2 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOC 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD15 pin */
+ AT91_PIOC 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD16 pin */
+ AT91_PIOC 17 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD17 pin */
+ };
+
+ pinctrl_lcd_rgb888: lcd-rgb-3 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD0 pin */
+ AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD1 pin */
+ AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD2 pin */
+ AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD3 pin */
+ AT91_PIOC 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD4 pin */
+ AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD5 pin */
+ AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD6 pin */
+ AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD7 pin */
+ AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD8 pin */
+ AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD9 pin */
+ AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD10 pin */
+ AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD11 pin */
+ AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD12 pin */
+ AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD13 pin */
+ AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD14 pin */
+ AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD15 pin */
+ AT91_PIOC 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD16 pin */
+ AT91_PIOC 17 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD17 pin */
+ AT91_PIOC 18 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD18 pin */
+ AT91_PIOC 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD19 pin */
+ AT91_PIOC 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD20 pin */
+ AT91_PIOC 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD21 pin */
+ AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* LCDD22 pin */
+ AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* LCDD23 pin */
+ };
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ periphck {
+ lcdc_clk: lcdc_clk@25 {
+ #clock-cells = <0>;
+ reg = <25>;
+ };
+ };
+
+ systemck {
+ lcdck: lcdck@3 {
+ #clock-cells = <0>;
+ reg = <3>;
+ clocks = <&mck>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5_macb0.dtsi b/arch/arm/dts/at91sam9x5_macb0.dtsi
new file mode 100644
index 0000000..1540e60
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5_macb0.dtsi
@@ -0,0 +1,67 @@
+/*
+ * at91sam9x5_macb0.dtsi - Device Tree Include file for AT91SAM9x5 SoC with 1
+ * Ethernet interface.
+ *
+ * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ macb0 {
+ pinctrl_macb0_rmii: macb0_rmii-0 {
+ atmel,pins =
+ <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB0 periph A */
+ AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB1 periph A */
+ AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB2 periph A */
+ AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB3 periph A */
+ AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB4 periph A */
+ AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB5 periph A */
+ AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB6 periph A */
+ AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB7 periph A */
+ AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB9 periph A */
+ AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB10 periph A */
+ };
+
+ pinctrl_macb0_rmii_mii: macb0_rmii_mii-0 {
+ atmel,pins =
+ <AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB8 periph A */
+ AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB11 periph A */
+ AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB12 periph A */
+ AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB13 periph A */
+ AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB14 periph A */
+ AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB15 periph A */
+ AT91_PIOB 16 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB16 periph A */
+ AT91_PIOB 17 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB17 periph A */
+ };
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ periphck {
+ macb0_clk: macb0_clk@24 {
+ #clock-cells = <0>;
+ reg = <24>;
+ };
+ };
+ };
+
+ macb0: ethernet@f802c000 {
+ compatible = "cdns,at91sam9260-macb", "cdns,macb";
+ reg = <0xf802c000 0x100>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii>;
+ clocks = <&macb0_clk>, <&macb0_clk>;
+ clock-names = "hclk", "pclk";
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5_macb1.dtsi b/arch/arm/dts/at91sam9x5_macb1.dtsi
new file mode 100644
index 0000000..be2eab4
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5_macb1.dtsi
@@ -0,0 +1,55 @@
+/*
+ * at91sam9x5_macb1.dtsi - Device Tree Include file for AT91SAM9x5 SoC with 2
+ * Ethernet interfaces.
+ *
+ * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ macb1 {
+ pinctrl_macb1_rmii: macb1_rmii-0 {
+ atmel,pins =
+ <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC16 periph B */
+ AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC18 periph B */
+ AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC19 periph B */
+ AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC20 periph B */
+ AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC21 periph B */
+ AT91_PIOC 27 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC27 periph B */
+ AT91_PIOC 28 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC28 periph B */
+ AT91_PIOC 29 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC29 periph B */
+ AT91_PIOC 30 AT91_PERIPH_B AT91_PINCTRL_NONE /* PC30 periph B */
+ AT91_PIOC 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC31 periph B */
+ };
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ periphck {
+ macb1_clk: macb1_clk@27 {
+ #clock-cells = <0>;
+ reg = <27>;
+ };
+ };
+ };
+
+ macb1: ethernet@f8030000 {
+ compatible = "cdns,at91sam9260-macb", "cdns,macb";
+ reg = <0xf8030000 0x100>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb1_rmii>;
+ clocks = <&macb1_clk>, <&macb1_clk>;
+ clock-names = "hclk", "pclk";
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5_usart3.dtsi b/arch/arm/dts/at91sam9x5_usart3.dtsi
new file mode 100644
index 0000000..5259219
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5_usart3.dtsi
@@ -0,0 +1,69 @@
+/*
+ * at91sam9x5_usart3.dtsi - Device Tree Include file for AT91SAM9x5 SoC with
+ * 4 USART.
+ *
+ * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ aliases {
+ serial4 = &usart3;
+ };
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ usart3 {
+ pinctrl_usart3: usart3-0 {
+ atmel,pins =
+ <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PC22 periph B with pullup */
+ AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC23 periph B */
+ };
+
+ pinctrl_usart3_rts: usart3_rts-0 {
+ atmel,pins =
+ <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC24 periph B */
+ };
+
+ pinctrl_usart3_cts: usart3_cts-0 {
+ atmel,pins =
+ <AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC25 periph B */
+ };
+
+ pinctrl_usart3_sck: usart3_sck-0 {
+ atmel,pins =
+ <AT91_PIOC 26 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC26 periph B */
+ };
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ periphck {
+ usart3_clk: usart3_clk@8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ };
+ };
+ };
+
+ usart3: serial@f8028000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8028000 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3>;
+ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(14)>,
+ <&dma1 1 (AT91_DMA_CFG_PER_ID(15) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+ dma-names = "tx", "rx";
+ clocks = <&usart3_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5cm.dtsi b/arch/arm/dts/at91sam9x5cm.dtsi
new file mode 100644
index 0000000..b098ad8
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5cm.dtsi
@@ -0,0 +1,100 @@
+/*
+ * at91sam9x5cm.dtsi - Device Tree Include file for AT91SAM9x5 CPU Module
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ memory {
+ reg = <0x20000000 0x8000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ 1wire_cm {
+ pinctrl_1wire_cm: 1wire_cm-0 {
+ atmel,pins = <AT91_PIOB 18 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; /* PB18 multidrive, conflicts with led */
+ };
+ };
+ };
+
+ rtc@fffffeb0 {
+ status = "okay";
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc; /* Enable PMECC */
+ atmel,pmecc-cap = <2>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ uboot@40000 {
+ label = "u-boot";
+ reg = <0x40000 0x80000>;
+ };
+
+ ubootenv@c0000 {
+ label = "U-Boot Env";
+ reg = <0xc0000 0x140000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x1f800000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pb18 {
+ label = "pb18";
+ gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ pd21 {
+ label = "pd21";
+ gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ 1wire_cm {
+ compatible = "w1-gpio";
+ gpios = <&pioB 18 GPIO_ACTIVE_HIGH>;
+ linux,open-drain;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_1wire_cm>;
+ status = "okay";
+ };
+
+};
diff --git a/arch/arm/dts/at91sam9x5dm.dtsi b/arch/arm/dts/at91sam9x5dm.dtsi
new file mode 100644
index 0000000..a620366
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5dm.dtsi
@@ -0,0 +1,66 @@
+/*
+ * at91sam9x5dm.dtsi - Device Tree file for SAM9x5 display module
+ *
+ * Copyright (C) 2014 Atmel,
+ * 2014 Free Electrons
+ *
+ * Author: Boris Brezillon <boris.brezillon@free-electrons.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+ ahb {
+ apb {
+ i2c0: i2c@f8010000 {
+ qt1070: keyboard@1b {
+ compatible = "qt1070";
+ reg = <0x1b>;
+ interrupt-parent = <&pioA>;
+ interrupts = <7 0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qt1070_irq>;
+ wakeup-source;
+ };
+ };
+
+ hlcdc: hlcdc@f8038000 {
+ atmel,vl-bpix = <4>;
+ atmel,guard-time = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_pwm &pinctrl_lcd_rgb888>;
+
+ display-timings {
+ u-boot,dm-pre-reloc;
+ 800x480 {
+ clock-frequency = <24000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hsync-len = <128>;
+ hfront-porch = <64>;
+ hback-porch = <64>;
+ vfront-porch = <22>;
+ vback-porch = <21>;
+ vsync-len = <2>;
+ u-boot,dm-pre-reloc;
+ };
+ };
+ };
+
+ adc0: adc@f804c000 {
+ atmel,adc-ts-wires = <4>;
+ atmel,adc-ts-pressure-threshold = <10000>;
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ board {
+ pinctrl_qt1070_irq: qt1070_irq {
+ atmel,pins =
+ <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/at91sam9x5ek.dtsi b/arch/arm/dts/at91sam9x5ek.dtsi
new file mode 100644
index 0000000..f2a532d
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5ek.dtsi
@@ -0,0 +1,167 @@
+/*
+ * at91sam9x5ek.dtsi - Device Tree file for AT91SAM9x5CM Base board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "at91sam9x5cm.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9X5-EK";
+ compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+ stdout-path = "serial0:115200n8";
+ u-boot,dm-pre-reloc;
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc@f0008000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_slot0_clk_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ mmc1: mmc@f000c000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc1
+ &pinctrl_mmc1_slot0_clk_cmd_dat0
+ &pinctrl_mmc1_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ dbgu: serial@fffff200 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ usart0: serial@f801c000 {
+ status = "okay";
+ };
+
+ usb2: gadget@f803c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_board_usb2>;
+ atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ i2c0: i2c@f8010000 {
+ status = "okay";
+
+ wm8731: wm8731@1a {
+ compatible = "wm8731";
+ reg = <0x1a>;
+ };
+ };
+
+ adc0: adc@f804c000 {
+ atmel,adc-ts-wires = <4>;
+ atmel,adc-ts-pressure-threshold = <10000>;
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ camera_sensor {
+ pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_MCK */
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
+ };
+ };
+
+ mmc1 {
+ pinctrl_board_mmc1: mmc1-board {
+ atmel,pins =
+ <AT91_PIOD 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD14 gpio CD pin pull up and deglitch */
+ };
+ };
+
+ usb2 {
+ pinctrl_board_usb2: usb2-board {
+ atmel,pins =
+ <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio vbus sense, deglitch */
+ };
+ };
+ };
+
+ spi0: spi@f0000000 {
+ status = "okay";
+ cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
+ spi_flash@0 {
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+
+ ssc0: ssc@f0010000 {
+ status = "okay";
+ };
+ };
+
+ usb0: ohci@00600000 {
+ status = "okay";
+ num-ports = <3>;
+ atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
+ &pioD 19 GPIO_ACTIVE_LOW
+ &pioD 20 GPIO_ACTIVE_LOW
+ >;
+ };
+
+ usb1: ehci@00700000 {
+ status = "okay";
+ };
+ };
+
+ sound {
+ compatible = "atmel,sam9x5-wm8731-audio";
+
+ atmel,model = "wm8731 @ AT91SAM9X5EK";
+
+ atmel,audio-routing =
+ "Headphone Jack", "RHPOUT",
+ "Headphone Jack", "LHPOUT",
+ "LLINEIN", "Line In Jack",
+ "RLINEIN", "Line In Jack";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8731>;
+ };
+};
diff --git a/arch/arm/dts/omap5-u-boot.dtsi b/arch/arm/dts/omap5-u-boot.dtsi
index 6305f57..9247314 100644
--- a/arch/arm/dts/omap5-u-boot.dtsi
+++ b/arch/arm/dts/omap5-u-boot.dtsi
@@ -10,6 +10,10 @@
/{
ocp {
u-boot,dm-pre-reloc;
+
+ ocp2scp@4a090000 {
+ compatible = "ti,omap-ocp2scp", "simple-bus";
+ };
};
};
diff --git a/arch/arm/dts/sama5d2.dtsi b/arch/arm/dts/sama5d2.dtsi
index a881d9e..8d89b83 100644
--- a/arch/arm/dts/sama5d2.dtsi
+++ b/arch/arm/dts/sama5d2.dtsi
@@ -29,6 +29,7 @@
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
+ u-boot,dm-pre-reloc;
usb1: ohci@00400000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
@@ -66,6 +67,7 @@
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
+ u-boot,dm-pre-reloc;
pmc: pmc@f0014000 {
compatible = "atmel,sama5d2-pmc", "syscon";
@@ -73,10 +75,12 @@
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
+ u-boot,dm-pre-reloc;
main: mainck {
compatible = "atmel,at91sam9x5-clk-main";
#clock-cells = <0>;
+ u-boot,dm-pre-reloc;
};
plla: pllack@0 {
@@ -87,6 +91,7 @@
atmel,clk-input-range = <12000000 12000000>;
#atmel,pll-clk-output-range-cells = <4>;
atmel,pll-clk-output-ranges = <600000000 1200000000 0 0>;
+ u-boot,dm-pre-reloc;
};
plladiv: plladivck {
@@ -117,6 +122,7 @@
compatible = "atmel,at91sam9x5-clk-utmi";
#clock-cells = <0>;
clocks = <&main>;
+ u-boot,dm-pre-reloc;
};
mck: masterck {
@@ -125,12 +131,14 @@
clocks = <&main>, <&plladiv>, <&utmi>;
atmel,clk-output-range = <124000000 166000000>;
atmel,clk-divisors = <1 2 4 3>;
+ u-boot,dm-pre-reloc;
};
h32ck: h32mxck {
#clock-cells = <0>;
compatible = "atmel,sama5d4-clk-h32mx";
clocks = <&mck>;
+ u-boot,dm-pre-reloc;
};
usb: usbck {
@@ -221,6 +229,7 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&h32ck>;
+ u-boot,dm-pre-reloc;
macb0_clk: macb0_clk@5 {
#clock-cells = <0>;
@@ -248,6 +257,7 @@
#clock-cells = <0>;
reg = <18>;
atmel,clk-output-range = <0 83000000>;
+ u-boot,dm-pre-reloc;
};
flx0_clk: flx0_clk@19 {
@@ -290,6 +300,7 @@
#clock-cells = <0>;
reg = <25>;
atmel,clk-output-range = <0 83000000>;
+ u-boot,dm-pre-reloc;
};
uart2_clk: uart2_clk@26 {
@@ -326,6 +337,7 @@
#clock-cells = <0>;
reg = <33>;
atmel,clk-output-range = <0 83000000>;
+ u-boot,dm-pre-reloc;
};
spi1_clk: spi1_clk@34 {
@@ -430,6 +442,7 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&mck>;
+ u-boot,dm-pre-reloc;
dma0_clk: dma0_clk@6 {
#clock-cells = <0>;
@@ -469,11 +482,13 @@
sdmmc0_hclk: sdmmc0_hclk@31 {
#clock-cells = <0>;
reg = <31>;
+ u-boot,dm-pre-reloc;
};
sdmmc1_hclk: sdmmc1_hclk@32 {
#clock-cells = <0>;
reg = <32>;
+ u-boot,dm-pre-reloc;
};
lcdc_clk: lcdc_clk@45 {
@@ -503,15 +518,18 @@
#size-cells = <0>;
interrupt-parent = <&pmc>;
clocks = <&main>, <&plla>, <&utmi>, <&mck>;
+ u-boot,dm-pre-reloc;
sdmmc0_gclk: sdmmc0_gclk@31 {
#clock-cells = <0>;
reg = <31>;
+ u-boot,dm-pre-reloc;
};
sdmmc1_gclk: sdmmc1_gclk@32 {
#clock-cells = <0>;
reg = <32>;
+ u-boot,dm-pre-reloc;
};
tcb0_gclk: tcb0_gclk@35 {
@@ -600,6 +618,8 @@
uart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
+ clocks = <&uart1_clk>;
+ clock-names = "usart";
status = "disabled";
};
@@ -661,9 +681,11 @@
clocks = <&pioA_clk>;
gpio-controller;
#gpio-cells = <2>;
+ u-boot,dm-pre-reloc;
pinctrl {
compatible = "atmel,sama5d2-pinctrl";
+ u-boot,dm-pre-reloc;
};
};
};
diff --git a/arch/arm/mach-at91/include/mach/atmel_mpddrc.h b/arch/arm/mach-at91/include/mach/atmel_mpddrc.h
index f6bcecd..803501f 100644
--- a/arch/arm/mach-at91/include/mach/atmel_mpddrc.h
+++ b/arch/arm/mach-at91/include/mach/atmel_mpddrc.h
@@ -186,9 +186,14 @@
#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_73 0x6
#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_110 0x7
-#define ATMEL_MPDDRC_IO_CALIBR_TZQIO 0x7f
+#define ATMEL_MPDDRC_IO_CALIBR_TZQIO (0x7f << 8)
#define ATMEL_MPDDRC_IO_CALIBR_TZQIO_(x) (((x) & 0x7f) << 8)
+#define ATMEL_MPDDRC_IO_CALIBR_CALCODEP (0xf << 16)
+#define ATMEL_MPDDRC_IO_CALIBR_CALCODEP_(x) (((x) & 0xf) << 16)
+#define ATMEL_MPDDRC_IO_CALIBR_CALCODEN (0xf << 20)
+#define ATMEL_MPDDRC_IO_CALIBR_CALCODEN_(x) (((x) & 0xf) << 20)
+
#define ATMEL_MPDDRC_IO_CALIBR_EN_CALIB (0x1 << 4)
/* Bit field in Read Data Path Register */
diff --git a/arch/sandbox/dts/test.dts b/arch/sandbox/dts/test.dts
index 094c5aa..9077a82 100644
--- a/arch/sandbox/dts/test.dts
+++ b/arch/sandbox/dts/test.dts
@@ -59,6 +59,23 @@
ping-add = <3>;
};
+ phy_provider0: gen_phy@0 {
+ compatible = "sandbox,phy";
+ #phy-cells = <1>;
+ };
+
+ phy_provider1: gen_phy@1 {
+ compatible = "sandbox,phy";
+ #phy-cells = <0>;
+ broken;
+ };
+
+ gen_phy_user: gen_phy_user {
+ compatible = "simple-bus";
+ phys = <&phy_provider0 0>, <&phy_provider0 1>, <&phy_provider1>;
+ phy-names = "phy1", "phy2", "phy3";
+ };
+
some-bus {
#address-cells = <1>;
#size-cells = <0>;
diff --git a/board/atmel/at91sam9260ek/Makefile b/board/atmel/at91sam9260ek/Makefile
index c6edbee..07c6184 100644
--- a/board/atmel/at91sam9260ek/Makefile
+++ b/board/atmel/at91sam9260ek/Makefile
@@ -10,5 +10,5 @@
#
obj-y += at91sam9260ek.o
-obj-y += led.o
+obj-$(CONFIG_AT91_LED) += led.o
obj-$(CONFIG_HAS_DATAFLASH) += partition.o
diff --git a/board/atmel/at91sam9260ek/at91sam9260ek.c b/board/atmel/at91sam9260ek/at91sam9260ek.c
index 98193bf..b087fce 100644
--- a/board/atmel/at91sam9260ek/at91sam9260ek.c
+++ b/board/atmel/at91sam9260ek/at91sam9260ek.c
@@ -7,18 +7,13 @@
*/
#include <common.h>
+#include <debug_uart.h>
#include <asm/io.h>
#include <asm/arch/at91sam9260_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
-#include <atmel_mci.h>
-
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-# include <net.h>
-#endif
-#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -67,81 +62,34 @@
}
#endif
-#ifdef CONFIG_MACB
-static void at91sam9260ek_macb_hw_init(void)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
- struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
-
- at91_periph_clk_enable(ATMEL_ID_EMAC0);
-
- /*
- * Disable pull-up on:
- * RXDV (PA17) => PHY normal mode (not Test mode)
- * ERX0 (PA14) => PHY ADDR0
- * ERX1 (PA15) => PHY ADDR1
- * ERX2 (PA25) => PHY ADDR2
- * ERX3 (PA26) => PHY ADDR3
- * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(pin_to_mask(AT91_PIN_PA14) |
- pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA17) |
- pin_to_mask(AT91_PIN_PA25) |
- pin_to_mask(AT91_PIN_PA26) |
- pin_to_mask(AT91_PIN_PA28),
- &pioa->pudr);
-
- at91_phy_reset();
-
- /* Re-enable pull-up */
- writel(pin_to_mask(AT91_PIN_PA14) |
- pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA17) |
- pin_to_mask(AT91_PIN_PA25) |
- pin_to_mask(AT91_PIN_PA26) |
- pin_to_mask(AT91_PIN_PA28),
- &pioa->puer);
-
- /* Initialize EMAC=MACB hardware */
- at91_macb_hw_init();
+ at91_seriald_hw_init();
}
#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bd)
-{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI);
-}
-#endif
-
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOC);
-
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
- at91_seriald_hw_init();
#ifdef CONFIG_CMD_NAND
at91sam9260ek_nand_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
at91_spi0_hw_init((1 << 0) | (1 << 1));
#endif
-#ifdef CONFIG_MACB
- at91sam9260ek_macb_hw_init();
-#endif
return 0;
}
@@ -159,12 +107,3 @@
{
}
#endif
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
-#endif
- return rc;
-}
diff --git a/board/atmel/at91sam9263ek/Makefile b/board/atmel/at91sam9263ek/Makefile
index 7b31f18..f3cd9d5 100644
--- a/board/atmel/at91sam9263ek/Makefile
+++ b/board/atmel/at91sam9263ek/Makefile
@@ -10,5 +10,5 @@
#
obj-y += at91sam9263ek.o
-obj-y += led.o
+obj-$(CONFIG_AT91_LED) += led.o
obj-$(CONFIG_HAS_DATAFLASH) += partition.o
diff --git a/board/atmel/at91sam9263ek/at91sam9263ek.c b/board/atmel/at91sam9263ek/at91sam9263ek.c
index e4e32f6..3de9783 100644
--- a/board/atmel/at91sam9263ek/at91sam9263ek.c
+++ b/board/atmel/at91sam9263ek/at91sam9263ek.c
@@ -7,6 +7,7 @@
*/
#include <common.h>
+#include <debug_uart.h>
#include <linux/sizes.h>
#include <asm/arch/at91sam9263.h>
#include <asm/arch/at91sam9_smc.h>
@@ -19,11 +20,6 @@
#include <asm/arch/hardware.h>
#include <lcd.h>
#include <atmel_lcdc.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
-#include <netdev.h>
-#include <atmel_mci.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -77,34 +73,6 @@
}
#endif
-#ifdef CONFIG_MACB
-static void at91sam9263ek_macb_hw_init(void)
-{
- at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
-
- at91_periph_clk_enable(ATMEL_ID_EMAC);
-
- /*
- * Disable pull-up on:
- * RXDV (PC25) => PHY normal mode (not Test mode)
- * ERX0 (PE25) => PHY ADDR0
- * ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(1 << 25, &pio->pioc.pudr);
- writel((1 << 25) | (1 <<26), &pio->pioe.pudr);
-
- at91_phy_reset();
-
- /* Re-enable pull-up */
- writel(1 << 25, &pio->pioc.puer);
- writel((1 << 25) | (1 <<26), &pio->pioe.puer);
-
- at91_macb_hw_init();
-}
-#endif
-
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
.vl_col = 240,
@@ -209,24 +177,22 @@
#endif /* CONFIG_LCD_INFO */
#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bd)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI1);
+ at91_seriald_hw_init();
}
#endif
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOCDE);
-
- at91_seriald_hw_init();
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
@@ -242,9 +208,6 @@
at91_set_pio_output(AT91_PIO_PORTE, 20, 1); /* select spi0 clock */
at91_spi0_hw_init(1 << 0);
#endif
-#ifdef CONFIG_MACB
- at91sam9263ek_macb_hw_init();
-#endif
#ifdef CONFIG_USB_OHCI_NEW
at91_uhp_hw_init();
#endif
@@ -267,12 +230,3 @@
{
}
#endif
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x00);
-#endif
- return rc;
-}
diff --git a/board/atmel/at91sam9m10g45ek/Makefile b/board/atmel/at91sam9m10g45ek/Makefile
index e5448ec..55cd946 100644
--- a/board/atmel/at91sam9m10g45ek/Makefile
+++ b/board/atmel/at91sam9m10g45ek/Makefile
@@ -10,4 +10,4 @@
#
obj-y += at91sam9m10g45ek.o
-obj-y += led.o
+obj-(CONFIG_AT91_LED) += led.o
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
index 6871916..d3bc5c6 100644
--- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
@@ -7,6 +7,7 @@
*/
#include <common.h>
+#include <debug_uart.h>
#include <asm/io.h>
#include <asm/arch/clk.h>
#include <asm/arch/at91sam9g45_matrix.h>
@@ -17,11 +18,6 @@
#include <lcd.h>
#include <linux/mtd/nand.h>
#include <atmel_lcdc.h>
-#include <atmel_mci.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
-#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -149,39 +145,6 @@
}
#endif
-#ifdef CONFIG_MACB
-static void at91sam9m10g45ek_macb_hw_init(void)
-{
- struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
-
- at91_periph_clk_enable(ATMEL_ID_EMAC);
-
- /*
- * Disable pull-up on:
- * RXDV (PA15) => PHY normal mode (not Test mode)
- * ERX0 (PA12) => PHY ADDR0
- * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- &pioa->pudr);
-
- at91_phy_reset();
-
- /* Re-enable pull-up */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- &pioa->puer);
-
- /* And the pins. */
- at91_macb_hw_init();
-}
-#endif
-
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
@@ -280,20 +243,22 @@
#endif /* CONFIG_LCD_INFO */
#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bis)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI0);
+ at91_seriald_hw_init();
}
#endif
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_seriald_hw_init();
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
@@ -313,15 +278,6 @@
#ifdef CONFIG_CMD_USB
at91sam9m10g45ek_usb_hw_init();
#endif
-#ifdef CONFIG_HAS_DATAFLASH
- at91_spi0_hw_init(1 << 0);
-#endif
-#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 4);
-#endif
-#ifdef CONFIG_MACB
- at91sam9m10g45ek_macb_hw_init();
-#endif
#ifdef CONFIG_LCD
at91sam9m10g45ek_lcd_hw_init();
#endif
@@ -340,48 +296,3 @@
{
}
#endif
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
-#endif
- return rc;
-}
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < 2;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- switch(slave->cs) {
- case 1:
- at91_set_gpio_output(AT91_PIN_PB18, 0);
- break;
- case 0:
- default:
- at91_set_gpio_output(AT91_PIN_PB3, 0);
- break;
- }
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- switch(slave->cs) {
- case 1:
- at91_set_gpio_output(AT91_PIN_PB18, 1);
- break;
- case 0:
- default:
- at91_set_gpio_output(AT91_PIN_PB3, 1);
- break;
- }
-}
-#endif /* CONFIG_ATMEL_SPI */
diff --git a/board/atmel/at91sam9n12ek/at91sam9n12ek.c b/board/atmel/at91sam9n12ek/at91sam9n12ek.c
index 58da2d2..1105428 100644
--- a/board/atmel/at91sam9n12ek/at91sam9n12ek.c
+++ b/board/atmel/at91sam9n12ek/at91sam9n12ek.c
@@ -13,9 +13,9 @@
#include <asm/arch/at91_rstc.h>
#include <asm/arch/at91_pio.h>
#include <asm/arch/clk.h>
+#include <debug_uart.h>
#include <lcd.h>
#include <atmel_hlcdc.h>
-#include <atmel_mci.h>
#include <netdev.h>
#ifdef CONFIG_LCD_INFO
@@ -132,48 +132,6 @@
#endif /* CONFIG_LCD_INFO */
#endif /* CONFIG_LCD */
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < 2;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 0:
- at91_set_pio_output(AT91_PIO_PORTA, 14, 0);
- break;
- case 1:
- at91_set_pio_output(AT91_PIO_PORTA, 7, 0);
- break;
- }
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 0:
- at91_set_pio_output(AT91_PIO_PORTA, 14, 1);
- break;
- case 1:
- at91_set_pio_output(AT91_PIO_PORTA, 7, 1);
- break;
- }
-}
-#endif /* CONFIG_ATMEL_SPI */
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bd)
-{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_HSMCI0);
-}
-#endif
-
#ifdef CONFIG_KS8851_MLL
void at91sam9n12ek_ks8851_hw_init(void)
{
@@ -205,14 +163,22 @@
}
#endif
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+ at91_seriald_hw_init();
+}
+#endif
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOAB);
- at91_periph_clk_enable(ATMEL_ID_PIOCD);
-
- at91_seriald_hw_init();
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
@@ -223,10 +189,6 @@
at91sam9n12ek_nand_hw_init();
#endif
-#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 0);
-#endif
-
#ifdef CONFIG_LCD
at91_lcd_hw_init();
#endif
diff --git a/board/atmel/at91sam9rlek/Makefile b/board/atmel/at91sam9rlek/Makefile
index 51daf8d..7acfee5 100644
--- a/board/atmel/at91sam9rlek/Makefile
+++ b/board/atmel/at91sam9rlek/Makefile
@@ -10,5 +10,5 @@
#
obj-y += at91sam9rlek.o
-obj-y += led.o
+obj-$(CONFIG_AT91_LED) += led.o
obj-$(CONFIG_HAS_DATAFLASH) += partition.o
diff --git a/board/atmel/at91sam9rlek/at91sam9rlek.c b/board/atmel/at91sam9rlek/at91sam9rlek.c
index 994f246..0b603ed 100644
--- a/board/atmel/at91sam9rlek/at91sam9rlek.c
+++ b/board/atmel/at91sam9rlek/at91sam9rlek.c
@@ -7,6 +7,7 @@
*/
#include <common.h>
+#include <debug_uart.h>
#include <asm/io.h>
#include <asm/arch/at91sam9rl.h>
#include <asm/arch/at91sam9rl_matrix.h>
@@ -18,10 +19,6 @@
#include <lcd.h>
#include <atmel_lcdc.h>
-#include <atmel_mci.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
DECLARE_GLOBAL_DATA_PTR;
@@ -159,24 +156,22 @@
#endif /* CONFIG_LCD_INFO */
#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bis)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI);
+ at91_seriald_hw_init();
}
#endif
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOC);
- at91_periph_clk_enable(ATMEL_ID_PIOD);
-
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
@@ -185,7 +180,6 @@
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
- at91_seriald_hw_init();
#ifdef CONFIG_CMD_NAND
at91sam9rlek_nand_hw_init();
#endif
diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
index cc81776..c661c77 100644
--- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c
+++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
@@ -12,20 +12,13 @@
#include <asm/arch/at91_rstc.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
+#include <debug_uart.h>
#include <lcd.h>
#include <atmel_hlcdc.h>
-#include <atmel_mci.h>
-#ifdef CONFIG_MACB
-#include <net.h>
-#endif
-#include <netdev.h>
#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>
#endif
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-#endif
DECLARE_GLOBAL_DATA_PTR;
@@ -92,21 +85,6 @@
}
#endif
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-
-#ifdef CONFIG_MACB
- if (has_emac0())
- rc = macb_eth_initialize(0,
- (void *)ATMEL_BASE_EMAC0, 0x00);
- if (has_emac1())
- rc = macb_eth_initialize(1,
- (void *)ATMEL_BASE_EMAC1, 0x00);
-#endif
- return rc;
-}
-
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
.vl_col = 800,
@@ -205,54 +183,22 @@
#endif /* CONFIG_LCD_INFO */
#endif /* CONFIG_LCD */
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
- return bus == 0 && cs < 2;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 1:
- at91_set_pio_output(AT91_PIO_PORTA, 7, 0);
- break;
- case 0:
- default:
- at91_set_pio_output(AT91_PIO_PORTA, 14, 0);
- break;
- }
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 1:
- at91_set_pio_output(AT91_PIO_PORTA, 7, 1);
- break;
- case 0:
- default:
- at91_set_pio_output(AT91_PIO_PORTA, 14, 1);
- break;
- }
-}
-#endif /* CONFIG_ATMEL_SPI */
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bd)
-{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_HSMCI0);
+ at91_seriald_hw_init();
}
#endif
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_seriald_hw_init();
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
@@ -266,14 +212,6 @@
at91sam9x5ek_nand_hw_init();
#endif
-#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 4);
-#endif
-
-#ifdef CONFIG_MACB
- at91_macb_hw_init();
-#endif
-
#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
at91_uhp_hw_init();
#endif
@@ -300,8 +238,6 @@
at91_mci_hw_init();
#elif CONFIG_SYS_USE_NANDFLASH
at91sam9x5ek_nand_hw_init();
-#elif CONFIG_SYS_USE_SPIFLASH
- at91_spi0_hw_init(1 << 4);
#endif
}
diff --git a/board/atmel/sama5d2_xplained/sama5d2_xplained.c b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
index c5337af..48f45b3 100644
--- a/board/atmel/sama5d2_xplained/sama5d2_xplained.c
+++ b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
@@ -11,16 +11,11 @@
#include <dm.h>
#include <i2c.h>
#include <lcd.h>
-#include <mmc.h>
-#include <net.h>
-#include <netdev.h>
-#include <spi.h>
#include <version.h>
#include <asm/io.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/atmel_pio4.h>
#include <asm/arch/atmel_mpddrc.h>
-#include <asm/arch/atmel_usba_udc.h>
#include <asm/arch/atmel_sdhci.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
@@ -118,22 +113,7 @@
#endif /* CONFIG_LCD_INFO */
#endif /* CONFIG_LCD */
-static void board_gmac_hw_init(void)
-{
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 14, 0); /* GTXCK */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 15, 0); /* GTXEN */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 16, 0); /* GRXDV */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 17, 0); /* GRXER */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 18, 0); /* GRX0 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 19, 0); /* GRX1 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 20, 0); /* GTX0 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 21, 0); /* GTX1 */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 22, 0); /* GMDC */
- atmel_pio4_set_f_periph(AT91_PIO_PORTB, 23, 0); /* GMDIO */
-
- at91_periph_clk_enable(ATMEL_ID_GMAC);
-}
-
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
static void board_uart1_hw_init(void)
{
atmel_pio4_set_a_periph(AT91_PIO_PORTD, 2, 1); /* URXD1 */
@@ -142,7 +122,6 @@
at91_periph_clk_enable(ATMEL_ID_UART1);
}
-#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
board_uart1_hw_init();
@@ -154,8 +133,6 @@
{
#ifdef CONFIG_DEBUG_UART
debug_uart_init();
-#else
- board_uart1_hw_init();
#endif
return 0;
@@ -167,18 +144,12 @@
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-#ifdef CONFIG_MACB
- board_gmac_hw_init();
-#endif
#ifdef CONFIG_LCD
board_lcd_hw_init();
#endif
#ifdef CONFIG_CMD_USB
board_usb_hw_init();
#endif
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
- at91_udp_hw_init();
-#endif
return 0;
}
@@ -190,24 +161,6 @@
return 0;
}
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
-#endif
-
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
- usba_udc_probe(&pdata);
-#ifdef CONFIG_USB_ETH_RNDIS
- usb_eth_initialize(bis);
-#endif
-#endif
-
- return rc;
-}
-
#ifdef CONFIG_CMD_I2C
static int set_ethaddr_from_eeprom(void)
{
diff --git a/board/atmel/sama5d4ek/sama5d4ek.c b/board/atmel/sama5d4ek/sama5d4ek.c
index ffb4a50..b2e7979 100644
--- a/board/atmel/sama5d4ek/sama5d4ek.c
+++ b/board/atmel/sama5d4ek/sama5d4ek.c
@@ -230,7 +230,6 @@
ATMEL_MPDDRC_CR_NR_ROW_14 |
ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
ATMEL_MPDDRC_CR_NB_8BANKS |
- ATMEL_MPDDRC_CR_NDQS_DISABLED |
ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
@@ -260,6 +259,8 @@
void mem_init(void)
{
struct atmel_mpddrc_config ddr2;
+ const struct atmel_mpddr *mpddr = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC;
+ u32 tmp;
ddr2_conf(&ddr2);
@@ -267,6 +268,19 @@
at91_periph_clk_enable(ATMEL_ID_MPDDRC);
at91_system_clk_enable(AT91_PMC_DDR);
+ tmp = ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_ONE_CYCLE;
+ writel(tmp, &mpddr->rd_data_path);
+
+ tmp = readl(&mpddr->io_calibr);
+ tmp = (tmp & ~(ATMEL_MPDDRC_IO_CALIBR_RDIV |
+ ATMEL_MPDDRC_IO_CALIBR_TZQIO |
+ ATMEL_MPDDRC_IO_CALIBR_CALCODEP |
+ ATMEL_MPDDRC_IO_CALIBR_CALCODEN)) |
+ ATMEL_MPDDRC_IO_CALIBR_DDR2_RZQ_52 |
+ ATMEL_MPDDRC_IO_CALIBR_TZQIO_(8) |
+ ATMEL_MPDDRC_IO_CALIBR_EN_CALIB;
+ writel(tmp, &mpddr->io_calibr);
+
/* DDRAM2 Controller initialize */
ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2);
}
diff --git a/common/scsi.c b/common/scsi.c
index d37222c..c456f5a 100644
--- a/common/scsi.c
+++ b/common/scsi.c
@@ -549,6 +549,52 @@
* to the user if mode = 1
*/
#if defined(CONFIG_DM_SCSI)
+static int do_scsi_scan_one(struct udevice *dev, int id, int lun, int mode)
+{
+ int ret;
+ struct udevice *bdev;
+ struct blk_desc bd;
+ struct blk_desc *bdesc;
+ char str[10];
+
+ /*
+ * detect the scsi driver to get information about its geometry (block
+ * size, number of blocks) and other parameters (ids, type, ...)
+ */
+ scsi_init_dev_desc_priv(&bd);
+ if (scsi_detect_dev(id, lun, &bd))
+ return -ENODEV;
+
+ /*
+ * Create only one block device and do detection
+ * to make sure that there won't be a lot of
+ * block devices created
+ */
+ snprintf(str, sizeof(str), "id%dlun%d", id, lun);
+ ret = blk_create_devicef(dev, "scsi_blk", str, IF_TYPE_SCSI, -1,
+ bd.blksz, bd.blksz * bd.lba, &bdev);
+ if (ret) {
+ debug("Can't create device\n");
+ return ret;
+ }
+
+ bdesc = dev_get_uclass_platdata(bdev);
+ bdesc->target = id;
+ bdesc->lun = lun;
+ bdesc->removable = bd.removable;
+ bdesc->type = bd.type;
+ memcpy(&bdesc->vendor, &bd.vendor, sizeof(bd.vendor));
+ memcpy(&bdesc->product, &bd.product, sizeof(bd.product));
+ memcpy(&bdesc->revision, &bd.revision, sizeof(bd.revision));
+ part_init(bdesc);
+
+ if (mode == 1) {
+ printf(" Device %d: ", 0);
+ dev_print(bdesc);
+ }
+ return 0;
+}
+
int scsi_scan(int mode)
{
unsigned char i, lun;
@@ -576,59 +622,9 @@
/* Get controller platdata */
plat = dev_get_platdata(dev);
- for (i = 0; i < plat->max_id; i++) {
- for (lun = 0; lun < plat->max_lun; lun++) {
- struct udevice *bdev; /* block device */
- /* block device description */
- struct blk_desc _bd;
- struct blk_desc *bdesc;
- char str[10];
-
- scsi_init_dev_desc_priv(&_bd);
- ret = scsi_detect_dev(i, lun, &_bd);
- if (ret)
- /*
- * no device detected?
- * check the next lun.
- */
- continue;
-
- /*
- * Create only one block device and do detection
- * to make sure that there won't be a lot of
- * block devices created
- */
- snprintf(str, sizeof(str), "id%dlun%d", i, lun);
- ret = blk_create_devicef(dev, "scsi_blk",
- str, IF_TYPE_SCSI,
- -1,
- _bd.blksz,
- _bd.blksz * _bd.lba,
- &bdev);
- if (ret) {
- debug("Can't create device\n");
- return ret;
- }
-
- bdesc = dev_get_uclass_platdata(bdev);
- bdesc->target = i;
- bdesc->lun = lun;
- bdesc->removable = _bd.removable;
- bdesc->type = _bd.type;
- memcpy(&bdesc->vendor, &_bd.vendor,
- sizeof(_bd.vendor));
- memcpy(&bdesc->product, &_bd.product,
- sizeof(_bd.product));
- memcpy(&bdesc->revision, &_bd.revision,
- sizeof(_bd.revision));
- part_init(bdesc);
-
- if (mode == 1) {
- printf(" Device %d: ", 0);
- dev_print(bdesc);
- } /* if mode */
- } /* next LUN */
- }
+ for (i = 0; i < plat->max_id; i++)
+ for (lun = 0; lun < plat->max_lun; lun++)
+ do_scsi_scan_one(dev, i, lun, mode);
}
return 0;
diff --git a/configs/at91sam9260ek_dataflash_cs0_defconfig b/configs/at91sam9260ek_dataflash_cs0_defconfig
index e00c4c4..cc3f0a8 100644
--- a/configs/at91sam9260ek_dataflash_cs0_defconfig
+++ b/configs/at91sam9260ek_dataflash_cs0_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260,SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9260ek_dataflash_cs1_defconfig b/configs/at91sam9260ek_dataflash_cs1_defconfig
index 7b81775..cb621df 100644
--- a/configs/at91sam9260ek_dataflash_cs1_defconfig
+++ b/configs/at91sam9260ek_dataflash_cs1_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260,SYS_USE_DATAFLASH_CS1"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9260ek_nandflash_defconfig b/configs/at91sam9260ek_nandflash_defconfig
index ca71891..20d3565 100644
--- a/configs/at91sam9260ek_nandflash_defconfig
+++ b/configs/at91sam9260ek_nandflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9263ek_dataflash_cs0_defconfig b/configs/at91sam9263ek_dataflash_cs0_defconfig
index 6605a0e..02e9114 100644
--- a/configs/at91sam9263ek_dataflash_cs0_defconfig
+++ b/configs/at91sam9263ek_dataflash_cs0_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -21,7 +23,27 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9263ek_dataflash_defconfig b/configs/at91sam9263ek_dataflash_defconfig
index 6605a0e..02e9114 100644
--- a/configs/at91sam9263ek_dataflash_defconfig
+++ b/configs/at91sam9263ek_dataflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -21,7 +23,27 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9263ek_nandflash_defconfig b/configs/at91sam9263ek_nandflash_defconfig
index 9c6bab9..2ddcf2b 100644
--- a/configs/at91sam9263ek_nandflash_defconfig
+++ b/configs/at91sam9263ek_nandflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -21,7 +23,27 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9263ek_norflash_boot_defconfig b/configs/at91sam9263ek_norflash_boot_defconfig
index 5a4324f..21480c5 100644
--- a/configs/at91sam9263ek_norflash_boot_defconfig
+++ b/configs/at91sam9263ek_norflash_boot_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_BOOT_NORFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -21,8 +23,28 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9263ek_norflash_defconfig b/configs/at91sam9263ek_norflash_defconfig
index 78ce6bd..824c366 100644
--- a/configs/at91sam9263ek_norflash_defconfig
+++ b/configs/at91sam9263ek_norflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_NORFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -21,8 +23,28 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9g20ek_2mmc_defconfig b/configs/at91sam9g20ek_2mmc_defconfig
index 67c8232..18e88a7 100644
--- a/configs/at91sam9g20ek_2mmc_defconfig
+++ b/configs/at91sam9g20ek_2mmc_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek_2mmc"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_MMC"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -18,6 +20,26 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9g20ek_2mmc_nandflash_defconfig b/configs/at91sam9g20ek_2mmc_nandflash_defconfig
index 6d2bfa1..fb0d87a 100644
--- a/configs/at91sam9g20ek_2mmc_nandflash_defconfig
+++ b/configs/at91sam9g20ek_2mmc_nandflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek_2mmc"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -18,6 +20,26 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9g20ek_dataflash_cs0_defconfig b/configs/at91sam9g20ek_dataflash_cs0_defconfig
index 5bb0cb2..27c1c10 100644
--- a/configs/at91sam9g20ek_dataflash_cs0_defconfig
+++ b/configs/at91sam9g20ek_dataflash_cs0_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9g20ek_dataflash_cs1_defconfig b/configs/at91sam9g20ek_dataflash_cs1_defconfig
index fb6a0ac..1826e6c 100644
--- a/configs/at91sam9g20ek_dataflash_cs1_defconfig
+++ b/configs/at91sam9g20ek_dataflash_cs1_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,SYS_USE_DATAFLASH_CS1"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9g20ek_nandflash_defconfig b/configs/at91sam9g20ek_nandflash_defconfig
index 79ec2e4..1ac8863 100644
--- a/configs/at91sam9g20ek_nandflash_defconfig
+++ b/configs/at91sam9g20ek_nandflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9m10g45ek_mmc_defconfig b/configs/at91sam9m10g45ek_mmc_defconfig
index 342fc8a..18b6ddf7 100644
--- a/configs/at91sam9m10g45ek_mmc_defconfig
+++ b/configs/at91sam9m10g45ek_mmc_defconfig
@@ -1,19 +1,13 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9M10G45EK=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_FAT_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9m10g45ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_MMC"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SPL=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
# CONFIG_CMD_BDI is not set
@@ -29,7 +23,29 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9m10g45ek_nandflash_defconfig b/configs/at91sam9m10g45ek_nandflash_defconfig
index 7164d82..eda54a4 100644
--- a/configs/at91sam9m10g45ek_nandflash_defconfig
+++ b/configs/at91sam9m10g45ek_nandflash_defconfig
@@ -1,17 +1,13 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9M10G45EK=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9m10g45ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SPL=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
# CONFIG_CMD_BDI is not set
@@ -27,7 +23,29 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9n12ek_mmc_defconfig b/configs/at91sam9n12ek_mmc_defconfig
index ef9250b..e7e8a01 100644
--- a/configs/at91sam9n12ek_mmc_defconfig
+++ b/configs/at91sam9n12ek_mmc_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9N12EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9n12ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9N12,SYS_USE_MMC"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -19,9 +21,30 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9n12ek_nandflash_defconfig b/configs/at91sam9n12ek_nandflash_defconfig
index db88973..e626805 100644
--- a/configs/at91sam9n12ek_nandflash_defconfig
+++ b/configs/at91sam9n12ek_nandflash_defconfig
@@ -1,17 +1,13 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9N12EK=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9n12ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9N12,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SPL=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_CMD_BOOTZ=y
@@ -25,9 +21,30 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9n12ek_spiflash_defconfig b/configs/at91sam9n12ek_spiflash_defconfig
index 4e5d102..a5abcd1 100644
--- a/configs/at91sam9n12ek_spiflash_defconfig
+++ b/configs/at91sam9n12ek_spiflash_defconfig
@@ -1,18 +1,13 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9N12EK=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9n12ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9N12,SYS_USE_SPIFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SPL=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_CMD_BOOTZ=y
@@ -26,9 +21,30 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9rlek_dataflash_defconfig b/configs/at91sam9rlek_dataflash_defconfig
index 49e1353..d4abb2a 100644
--- a/configs/at91sam9rlek_dataflash_defconfig
+++ b/configs/at91sam9rlek_dataflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9RLEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9rlek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9RL,SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -20,5 +22,23 @@
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9rlek_mmc_defconfig b/configs/at91sam9rlek_mmc_defconfig
index 483d9b6..9a40c41 100644
--- a/configs/at91sam9rlek_mmc_defconfig
+++ b/configs/at91sam9rlek_mmc_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9RLEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9rlek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9RL,SYS_USE_MMC"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -20,5 +22,23 @@
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9rlek_nandflash_defconfig b/configs/at91sam9rlek_nandflash_defconfig
index d7f2d7f..d68b562 100644
--- a/configs/at91sam9rlek_nandflash_defconfig
+++ b/configs/at91sam9rlek_nandflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9RLEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9rlek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9RL,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -20,5 +22,23 @@
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=100000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9x5ek_dataflash_defconfig b/configs/at91sam9x5ek_dataflash_defconfig
index e07e217..64707db 100644
--- a/configs/at91sam9x5ek_dataflash_defconfig
+++ b/configs/at91sam9x5ek_dataflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9X5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -21,9 +23,34 @@
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9x5ek_mmc_defconfig b/configs/at91sam9x5ek_mmc_defconfig
index 9a95a04..ddeeeef 100644
--- a/configs/at91sam9x5ek_mmc_defconfig
+++ b/configs/at91sam9x5ek_mmc_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9X5EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_MMC"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
@@ -21,9 +23,34 @@
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9x5ek_nandflash_defconfig b/configs/at91sam9x5ek_nandflash_defconfig
index d93f687..a26b38f 100644
--- a/configs/at91sam9x5ek_nandflash_defconfig
+++ b/configs/at91sam9x5ek_nandflash_defconfig
@@ -1,17 +1,13 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9X5EK=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SPL=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_CMD_BOOTZ=y
@@ -27,9 +23,34 @@
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9x5ek_spiflash_defconfig b/configs/at91sam9x5ek_spiflash_defconfig
index 5fc512b..75d25d8 100644
--- a/configs/at91sam9x5ek_spiflash_defconfig
+++ b/configs/at91sam9x5ek_spiflash_defconfig
@@ -1,18 +1,13 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9X5EK=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_SPIFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_SPL=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_CMD_BOOTZ=y
@@ -28,9 +23,34 @@
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9xeek_dataflash_cs0_defconfig b/configs/at91sam9xeek_dataflash_cs0_defconfig
index e29b3cd..80673d2 100644
--- a/configs/at91sam9xeek_dataflash_cs0_defconfig
+++ b/configs/at91sam9xeek_dataflash_cs0_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9XE,SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9xeek_dataflash_cs1_defconfig b/configs/at91sam9xeek_dataflash_cs1_defconfig
index 2e32ca8..8922065 100644
--- a/configs/at91sam9xeek_dataflash_cs1_defconfig
+++ b/configs/at91sam9xeek_dataflash_cs1_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9XE,SYS_USE_DATAFLASH_CS1"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/at91sam9xeek_nandflash_defconfig b/configs/at91sam9xeek_nandflash_defconfig
index 2ef459b..9c28a59 100644
--- a/configs/at91sam9xeek_nandflash_defconfig
+++ b/configs/at91sam9xeek_nandflash_defconfig
@@ -1,6 +1,8 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9XE,SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -17,7 +19,24 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
index b50a762..9f96f15 100644
--- a/configs/dra7xx_evm_defconfig
+++ b/configs/dra7xx_evm_defconfig
@@ -38,7 +38,13 @@
CONFIG_OF_LIST="dra7-evm dra72-evm dra72-evm-revc dra71-evm"
CONFIG_DM=y
CONFIG_SPL_DM=y
-# CONFIG_BLK is not set
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+CONFIG_BLK=y
+CONFIG_DM_SCSI=y
+CONFIG_DWC_AHCI=y
CONFIG_DFU_MMC=y
CONFIG_DFU_RAM=y
CONFIG_DFU_SF=y
@@ -68,6 +74,7 @@
CONFIG_TIMER=y
CONFIG_OMAP_TIMER=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
CONFIG_USB_XHCI_DRA7XX_INDEX=1
@@ -81,3 +88,6 @@
CONFIG_G_DNL_MANUFACTURER="Texas Instruments"
CONFIG_G_DNL_VENDOR_NUM=0x0451
CONFIG_G_DNL_PRODUCT_NUM=0xd022
+CONFIG_SPL_PHY=y
+CONFIG_PIPE3_PHY=y
+CONFIG_SPL_PIPE3_PHY=y
diff --git a/configs/dra7xx_hs_evm_defconfig b/configs/dra7xx_hs_evm_defconfig
index 568c3f6..84dd26b 100644
--- a/configs/dra7xx_hs_evm_defconfig
+++ b/configs/dra7xx_hs_evm_defconfig
@@ -43,7 +43,12 @@
CONFIG_OF_LIST="dra7-evm dra72-evm dra72-evm-revc dra71-evm"
CONFIG_DM=y
CONFIG_SPL_DM=y
-# CONFIG_BLK is not set
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+CONFIG_DM_SCSI=y
+CONFIG_DWC_AHCI=y
CONFIG_DFU_MMC=y
CONFIG_DFU_RAM=y
CONFIG_DFU_SF=y
@@ -73,6 +78,7 @@
CONFIG_TIMER=y
CONFIG_OMAP_TIMER=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
CONFIG_USB_XHCI_DRA7XX_INDEX=1
@@ -86,3 +92,6 @@
CONFIG_G_DNL_MANUFACTURER="Texas Instruments"
CONFIG_G_DNL_VENDOR_NUM=0x0451
CONFIG_G_DNL_PRODUCT_NUM=0xd022
+CONFIG_SPL_PHY=y
+CONFIG_PIPE3_PHY=y
+CONFIG_SPL_PIPE3_PHY=y
diff --git a/configs/sama5d2_xplained_mmc_defconfig b/configs/sama5d2_xplained_mmc_defconfig
index 500f497..f064a43 100644
--- a/configs/sama5d2_xplained_mmc_defconfig
+++ b/configs/sama5d2_xplained_mmc_defconfig
@@ -8,12 +8,15 @@
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_FAT_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_xplained"
CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SPL=y
+CONFIG_SPL_SEPARATE_BSS=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
@@ -30,8 +33,10 @@
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
CONFIG_DM=y
CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_CLK=y
CONFIG_SPL_CLK=y
CONFIG_CLK_AT91=y
@@ -48,13 +53,16 @@
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_AT91PIO4=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_ATMEL=y
CONFIG_DEBUG_UART_BASE=0xf8020000
-CONFIG_DEBUG_UART_CLOCK=0
+CONFIG_DEBUG_UART_CLOCK=83000000
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
diff --git a/configs/sama5d2_xplained_spiflash_defconfig b/configs/sama5d2_xplained_spiflash_defconfig
index 9fc8aa2..70a17ed 100644
--- a/configs/sama5d2_xplained_spiflash_defconfig
+++ b/configs/sama5d2_xplained_spiflash_defconfig
@@ -4,9 +4,11 @@
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_xplained"
CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_SERIALFLASH"
@@ -29,8 +31,10 @@
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
CONFIG_DM=y
CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_CLK=y
CONFIG_SPL_CLK=y
CONFIG_CLK_AT91=y
@@ -47,13 +51,16 @@
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_AT91PIO4=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_ATMEL=y
CONFIG_DEBUG_UART_BASE=0xf8020000
-CONFIG_DEBUG_UART_CLOCK=0
+CONFIG_DEBUG_UART_CLOCK=83000000
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
diff --git a/configs/sama5d36ek_cmp_mmc_defconfig b/configs/sama5d36ek_cmp_mmc_defconfig
new file mode 100644
index 0000000..32a21f9
--- /dev/null
+++ b/configs/sama5d36ek_cmp_mmc_defconfig
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_MMC"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
diff --git a/configs/sama5d36ek_cmp_nandflash_defconfig b/configs/sama5d36ek_cmp_nandflash_defconfig
new file mode 100644
index 0000000..34c4de1
--- /dev/null
+++ b/configs/sama5d36ek_cmp_nandflash_defconfig
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_NANDFLASH"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
diff --git a/configs/sama5d36ek_cmp_spiflash_defconfig b/configs/sama5d36ek_cmp_spiflash_defconfig
new file mode 100644
index 0000000..42c3111
--- /dev/null
+++ b/configs/sama5d36ek_cmp_spiflash_defconfig
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_SERIALFLASH"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
diff --git a/configs/sandbox_defconfig b/configs/sandbox_defconfig
index 64bb923..95630fc 100644
--- a/configs/sandbox_defconfig
+++ b/configs/sandbox_defconfig
@@ -172,6 +172,8 @@
CONFIG_VIDEO_SANDBOX_SDL=y
CONFIG_FS_CBFS=y
CONFIG_FS_CRAMFS=y
+CONFIG_PHY=y
+CONFIG_PHY_SANDBOX=y
CONFIG_CMD_DHRYSTONE=y
CONFIG_TPM=y
CONFIG_LZ4=y
diff --git a/configs/sandbox_noblk_defconfig b/configs/sandbox_noblk_defconfig
index fb98ab8..26183af 100644
--- a/configs/sandbox_noblk_defconfig
+++ b/configs/sandbox_noblk_defconfig
@@ -174,6 +174,8 @@
CONFIG_VIDEO_SANDBOX_SDL=y
CONFIG_FS_CBFS=y
CONFIG_FS_CRAMFS=y
+CONFIG_PHY=y
+CONFIG_PHY_SANDBOX=y
CONFIG_CMD_DHRYSTONE=y
CONFIG_TPM=y
CONFIG_LZ4=y
diff --git a/configs/sandbox_spl_defconfig b/configs/sandbox_spl_defconfig
index 9b7b1fe..9324353 100644
--- a/configs/sandbox_spl_defconfig
+++ b/configs/sandbox_spl_defconfig
@@ -178,6 +178,8 @@
CONFIG_VIDEO_SANDBOX_SDL=y
CONFIG_FS_CBFS=y
CONFIG_FS_CRAMFS=y
+CONFIG_PHY=y
+CONFIG_PHY_SANDBOX=y
CONFIG_CMD_DHRYSTONE=y
CONFIG_TPM=y
CONFIG_LZ4=y
diff --git a/drivers/Kconfig b/drivers/Kconfig
index a096dad..a5f24d7 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -54,6 +54,8 @@
source "drivers/pcmcia/Kconfig"
+source "drivers/phy/Kconfig"
+
source "drivers/phy/marvell/Kconfig"
source "drivers/pinctrl/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 4a4b237..6916420 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -5,6 +5,7 @@
obj-$(CONFIG_$(SPL_TPL_)DM) += core/
obj-$(CONFIG_$(SPL_)CLK) += clk/
obj-$(CONFIG_$(SPL_)LED) += led/
+obj-$(CONFIG_$(SPL_)PHY) += phy/
obj-$(CONFIG_$(SPL_)PINCTRL) += pinctrl/
obj-$(CONFIG_$(SPL_)RAM) += ram/
diff --git a/drivers/block/Kconfig b/drivers/block/Kconfig
index 88e66e2..6cbe145 100644
--- a/drivers/block/Kconfig
+++ b/drivers/block/Kconfig
@@ -48,4 +48,14 @@
ZynqMP. Support up to 2 external devices. Complient with SATA 3.1 and
AHCI 1.3 specifications with hot-plug detect feature.
+
+config DWC_AHCI
+ bool "Enable Synopsys DWC AHCI driver support"
+ select SCSI_AHCI
+ select PHY
+ depends on DM_SCSI
+ help
+ Enable this driver to support Sata devices through
+ Synopsys DWC AHCI module.
+
endmenu
diff --git a/drivers/block/Makefile b/drivers/block/Makefile
index f415b33..d89c8b0 100644
--- a/drivers/block/Makefile
+++ b/drivers/block/Makefile
@@ -11,6 +11,7 @@
obj-y += blk_legacy.o
endif
+obj-$(CONFIG_DWC_AHCI) += dwc_ahci.o
obj-$(CONFIG_AHCI) += ahci-uclass.o
obj-$(CONFIG_DM_SCSI) += scsi-uclass.o
obj-$(CONFIG_SCSI_AHCI) += ahci.o
diff --git a/drivers/block/dwc_ahci.c b/drivers/block/dwc_ahci.c
new file mode 100644
index 0000000..d5bb0b8
--- /dev/null
+++ b/drivers/block/dwc_ahci.c
@@ -0,0 +1,101 @@
+/*
+ * DWC SATA platform driver
+ *
+ * (C) Copyright 2016
+ * Texas Instruments Incorporated, <www.ti.com>
+ *
+ * Author: Mugunthan V N <mugunthanvnm@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <ahci.h>
+#include <scsi.h>
+#include <sata.h>
+#include <asm/arch/sata.h>
+#include <asm/io.h>
+#include <generic-phy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct dwc_ahci_priv {
+ void *base;
+ void *wrapper_base;
+};
+
+static int dwc_ahci_ofdata_to_platdata(struct udevice *dev)
+{
+ struct dwc_ahci_priv *priv = dev_get_priv(dev);
+ struct scsi_platdata *plat = dev_get_platdata(dev);
+ fdt_addr_t addr;
+
+ plat->max_id = fdtdec_get_uint(gd->fdt_blob, dev->of_offset, "max-id",
+ CONFIG_SYS_SCSI_MAX_SCSI_ID);
+ plat->max_lun = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+ "max-lun", CONFIG_SYS_SCSI_MAX_LUN);
+
+ priv->base = map_physmem(dev_get_addr(dev), sizeof(void *),
+ MAP_NOCACHE);
+
+ addr = dev_get_addr_index(dev, 1);
+ if (addr != FDT_ADDR_T_NONE) {
+ priv->wrapper_base = map_physmem(addr, sizeof(void *),
+ MAP_NOCACHE);
+ } else {
+ priv->wrapper_base = NULL;
+ }
+
+ return 0;
+}
+
+static int dwc_ahci_probe(struct udevice *dev)
+{
+ struct dwc_ahci_priv *priv = dev_get_priv(dev);
+ int ret;
+ struct phy phy;
+
+ ret = generic_phy_get_by_name(dev, "sata-phy", &phy);
+ if (ret) {
+ error("can't get the phy from DT\n");
+ return ret;
+ }
+
+ ret = generic_phy_init(&phy);
+ if (ret) {
+ error("unable to initialize the sata phy\n");
+ return ret;
+ }
+
+ ret = generic_phy_power_on(&phy);
+ if (ret) {
+ error("unable to power on the sata phy\n");
+ return ret;
+ }
+
+ if (priv->wrapper_base) {
+ u32 val = TI_SATA_IDLE_NO | TI_SATA_STANDBY_NO;
+
+ /* Enable SATA module, No Idle, No Standby */
+ writel(val, priv->wrapper_base + TI_SATA_SYSCONFIG);
+ }
+
+ return ahci_init(priv->base);
+}
+
+static const struct udevice_id dwc_ahci_ids[] = {
+ { .compatible = "snps,dwc-ahci" },
+ { }
+};
+
+U_BOOT_DRIVER(dwc_ahci) = {
+ .name = "dwc_ahci",
+ .id = UCLASS_SCSI,
+ .of_match = dwc_ahci_ids,
+ .ofdata_to_platdata = dwc_ahci_ofdata_to_platdata,
+ .probe = dwc_ahci_probe,
+ .priv_auto_alloc_size = sizeof(struct dwc_ahci_priv),
+ .platdata_auto_alloc_size = sizeof(struct scsi_platdata),
+ .flags = DM_FLAG_ALLOC_PRIV_DMA,
+};
diff --git a/drivers/clk/at91/clk-master.c b/drivers/clk/at91/clk-master.c
index 284b248..72d0a73 100644
--- a/drivers/clk/at91/clk-master.c
+++ b/drivers/clk/at91/clk-master.c
@@ -21,6 +21,7 @@
};
static const struct udevice_id at91_master_clk_match[] = {
+ { .compatible = "atmel,at91rm9200-clk-master" },
{ .compatible = "atmel,at91sam9x5-clk-master" },
{}
};
diff --git a/drivers/clk/at91/clk-peripheral.c b/drivers/clk/at91/clk-peripheral.c
index e1ed447..62fabe3 100644
--- a/drivers/clk/at91/clk-peripheral.c
+++ b/drivers/clk/at91/clk-peripheral.c
@@ -16,6 +16,10 @@
#define PERIPHERAL_ID_MAX 31
#define PERIPHERAL_MASK(id) (1 << ((id) & PERIPHERAL_ID_MAX))
+enum periph_clk_type {
+ CLK_PERIPH_AT91RM9200 = 0,
+ CLK_PERIPH_AT91SAM9X5,
+};
/**
* sam9x5_periph_clk_bind() - for the periph clock driver
* Recursively bind its children as clk devices.
@@ -28,7 +32,14 @@
}
static const struct udevice_id sam9x5_periph_clk_match[] = {
- { .compatible = "atmel,at91sam9x5-clk-peripheral" },
+ {
+ .compatible = "atmel,at91rm9200-clk-peripheral",
+ .data = CLK_PERIPH_AT91RM9200,
+ },
+ {
+ .compatible = "atmel,at91sam9x5-clk-peripheral",
+ .data = CLK_PERIPH_AT91SAM9X5,
+ },
{}
};
@@ -45,12 +56,24 @@
{
struct pmc_platdata *plat = dev_get_platdata(clk->dev);
struct at91_pmc *pmc = plat->reg_base;
+ enum periph_clk_type clk_type;
+ void *addr;
if (clk->id < PERIPHERAL_ID_MIN)
return -1;
- writel(clk->id & AT91_PMC_PCR_PID_MASK, &pmc->pcr);
- setbits_le32(&pmc->pcr, AT91_PMC_PCR_CMD_WRITE | AT91_PMC_PCR_EN);
+ clk_type = dev_get_driver_data(dev_get_parent(clk->dev));
+ if (clk_type == CLK_PERIPH_AT91RM9200) {
+ addr = &pmc->pcer;
+ if (clk->id > PERIPHERAL_ID_MAX)
+ addr = &pmc->pcer1;
+
+ setbits_le32(addr, PERIPHERAL_MASK(clk->id));
+ } else {
+ writel(clk->id & AT91_PMC_PCR_PID_MASK, &pmc->pcr);
+ setbits_le32(&pmc->pcr,
+ AT91_PMC_PCR_CMD_WRITE | AT91_PMC_PCR_EN);
+ }
return 0;
}
diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c
index fcd693a..72d52c5 100644
--- a/drivers/clk/at91/pmc.c
+++ b/drivers/clk/at91/pmc.c
@@ -16,6 +16,12 @@
DECLARE_GLOBAL_DATA_PTR;
static const struct udevice_id at91_pmc_match[] = {
+ { .compatible = "atmel,at91rm9200-pmc" },
+ { .compatible = "atmel,at91sam9260-pmc" },
+ { .compatible = "atmel,at91sam9g45-pmc" },
+ { .compatible = "atmel,at91sam9n12-pmc" },
+ { .compatible = "atmel,at91sam9x5-pmc" },
+ { .compatible = "atmel,sama5d3-pmc" },
{ .compatible = "atmel,sama5d2-pmc" },
{}
};
diff --git a/drivers/net/macb.c b/drivers/net/macb.c
index 402e866..21a620c 100644
--- a/drivers/net/macb.c
+++ b/drivers/net/macb.c
@@ -111,6 +111,9 @@
#endif
unsigned short phy_addr;
struct mii_dev *bus;
+#ifdef CONFIG_PHYLIB
+ struct phy_device *phydev;
+#endif
#ifdef CONFIG_DM_ETH
#ifdef CONFIG_CLK
@@ -479,9 +482,6 @@
#ifdef CONFIG_DM_ETH
struct macb_device *macb = dev_get_priv(dev);
#endif
-#ifdef CONFIG_PHYLIB
- struct phy_device *phydev;
-#endif
u32 ncfgr;
u16 phy_id, status, adv, lpa;
int media, speed, duplex;
@@ -503,19 +503,19 @@
#ifdef CONFIG_PHYLIB
#ifdef CONFIG_DM_ETH
- phydev = phy_connect(macb->bus, macb->phy_addr, dev,
+ macb->phydev = phy_connect(macb->bus, macb->phy_addr, dev,
macb->phy_interface);
#else
/* need to consider other phy interface mode */
- phydev = phy_connect(macb->bus, macb->phy_addr, &macb->netdev,
+ macb->phydev = phy_connect(macb->bus, macb->phy_addr, &macb->netdev,
PHY_INTERFACE_MODE_RGMII);
#endif
- if (!phydev) {
+ if (!macb->phydev) {
printf("phy_connect failed\n");
return -ENODEV;
}
- phy_config(phydev);
+ phy_config(macb->phydev);
#endif
status = macb_mdio_read(macb, MII_BMSR);
@@ -1035,6 +1035,7 @@
struct eth_pdata *pdata = dev_get_platdata(dev);
struct macb_device *macb = dev_get_priv(dev);
const char *phy_mode;
+ __maybe_unused int ret;
phy_mode = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), "phy-mode",
NULL);
@@ -1048,7 +1049,7 @@
macb->regs = (void *)pdata->iobase;
#ifdef CONFIG_CLK
- int ret = macb_enable_clk(dev);
+ ret = macb_enable_clk(dev);
if (ret)
return ret;
#endif
@@ -1056,23 +1057,35 @@
_macb_eth_initialize(macb);
#if defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB)
- int retval;
- struct mii_dev *mdiodev = mdio_alloc();
- if (!mdiodev)
+ macb->bus = mdio_alloc();
+ if (!macb->bus)
return -ENOMEM;
- strncpy(mdiodev->name, dev->name, MDIO_NAME_LEN);
- mdiodev->read = macb_miiphy_read;
- mdiodev->write = macb_miiphy_write;
+ strncpy(macb->bus->name, dev->name, MDIO_NAME_LEN);
+ macb->bus->read = macb_miiphy_read;
+ macb->bus->write = macb_miiphy_write;
- retval = mdio_register(mdiodev);
- if (retval < 0)
- return retval;
+ ret = mdio_register(macb->bus);
+ if (ret < 0)
+ return ret;
macb->bus = miiphy_get_dev_by_name(dev->name);
#endif
return 0;
}
+static int macb_eth_remove(struct udevice *dev)
+{
+ struct macb_device *macb = dev_get_priv(dev);
+
+#ifdef CONFIG_PHYLIB
+ free(macb->phydev);
+#endif
+ mdio_unregister(macb->bus);
+ mdio_free(macb->bus);
+
+ return 0;
+}
+
static int macb_eth_ofdata_to_platdata(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
@@ -1083,6 +1096,10 @@
static const struct udevice_id macb_eth_ids[] = {
{ .compatible = "cdns,macb" },
+ { .compatible = "cdns,at91sam9260-macb" },
+ { .compatible = "atmel,sama5d2-gem" },
+ { .compatible = "atmel,sama5d3-gem" },
+ { .compatible = "atmel,sama5d4-gem" },
{ }
};
@@ -1092,6 +1109,7 @@
.of_match = macb_eth_ids,
.ofdata_to_platdata = macb_eth_ofdata_to_platdata,
.probe = macb_eth_probe,
+ .remove = macb_eth_remove,
.ops = &macb_eth_ops,
.priv_auto_alloc_size = sizeof(struct macb_device),
.platdata_auto_alloc_size = sizeof(struct eth_pdata),
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
new file mode 100644
index 0000000..a91a694
--- /dev/null
+++ b/drivers/phy/Kconfig
@@ -0,0 +1,62 @@
+
+menu "PHY Subsystem"
+
+config PHY
+ bool "PHY Core"
+ depends on DM
+ help
+ PHY support.
+
+ This framework is designed to provide a generic interface for PHY
+ devices. PHY devices are dedicated hardware that handle the physical
+ layer of the protocols in the OSI model.
+ PHYs are commonly used for high speed interfaces such as Serial-ATA
+ or PCI express.
+ The API provides functions to initialize/deinitialize the
+ PHY, power on/off the PHY, and reset the PHY. It's meant to be as
+ compatible as possible with the equivalent framework found in the
+ linux kernel.
+
+config SPL_PHY
+ bool "PHY Core in SPL"
+ depends on DM
+ help
+ PHY support in SPL.
+
+ This framework is designed to provide a generic interface for PHY
+ devices. PHY devices are dedicated hardware that handle the physical
+ layer of the protocols (https://en.wikipedia.org/wiki/OSI_model).
+ PHYs are commonly used for high speed interfaces such as Serial-ATA
+ or PCI express.
+ The API provides functions to initialize/deinitialize the
+ PHY, power on/off the PHY, and reset the PHY. It's meant to be as
+ compatible as possible with the equivalent framework found in the
+ linux kernel.
+
+config PHY_SANDBOX
+ bool "Sandbox PHY support"
+ depends on SANDBOX
+ depends on PHY
+ help
+ This select a dummy sandbox PHY driver. It used only to implement
+ the unit tests for the phy framework
+
+config PIPE3_PHY
+ bool "Support omap's PIPE3 PHY"
+ depends on PHY && ARCH_OMAP2
+ help
+ Support for the omap PIPE3 phy for sata
+
+ This PHY is found on omap devices supporting SATA such as dra7, am57x
+ and omap5
+
+config SPL_PIPE3_PHY
+ bool "Support omap's PIPE3 PHY in SPL"
+ depends on SPL_PHY && ARCH_OMAP2
+ help
+ Support for the omap PIPE3 phy for sata in SPL
+
+ This PHY is found on omap devices supporting SATA such as dra7, am57x
+ and omap5
+
+endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
new file mode 100644
index 0000000..6ce96d2
--- /dev/null
+++ b/drivers/phy/Makefile
@@ -0,0 +1,10 @@
+#
+# Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+# Written by Jean-Jacques Hiblot <jjhiblot@ti.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_$(SPL_)PHY) += phy-uclass.o
+obj-$(CONFIG_PHY_SANDBOX) += sandbox-phy.o
+obj-$(CONFIG_$(SPL_)PIPE3_PHY) += ti-pipe3-phy.o
diff --git a/drivers/phy/phy-uclass.c b/drivers/phy/phy-uclass.c
new file mode 100644
index 0000000..0d8bef7
--- /dev/null
+++ b/drivers/phy/phy-uclass.c
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Written by Jean-Jacques Hiblot <jjhiblot@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <generic-phy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static inline struct phy_ops *phy_dev_ops(struct udevice *dev)
+{
+ return (struct phy_ops *)dev->driver->ops;
+}
+
+static int generic_phy_xlate_offs_flags(struct phy *phy,
+ struct fdtdec_phandle_args *args)
+{
+ debug("%s(phy=%p)\n", __func__, phy);
+
+ if (args->args_count > 1) {
+ debug("Invaild args_count: %d\n", args->args_count);
+ return -EINVAL;
+ }
+
+ if (args->args_count)
+ phy->id = args->args[0];
+ else
+ phy->id = 0;
+
+
+ return 0;
+}
+
+int generic_phy_get_by_index(struct udevice *dev, int index,
+ struct phy *phy)
+{
+ struct fdtdec_phandle_args args;
+ struct phy_ops *ops;
+ int ret;
+ struct udevice *phydev;
+
+ debug("%s(dev=%p, index=%d, phy=%p)\n", __func__, dev, index, phy);
+
+ assert(phy);
+ ret = fdtdec_parse_phandle_with_args(gd->fdt_blob, dev_of_offset(dev),
+ "phys", "#phy-cells", 0, index,
+ &args);
+ if (ret) {
+ debug("%s: fdtdec_parse_phandle_with_args failed: err=%d\n",
+ __func__, ret);
+ return ret;
+ }
+
+ ret = uclass_get_device_by_of_offset(UCLASS_PHY, args.node, &phydev);
+ if (ret) {
+ debug("%s: uclass_get_device_by_of_offset failed: err=%d\n",
+ __func__, ret);
+ return ret;
+ }
+
+ phy->dev = phydev;
+
+ ops = phy_dev_ops(phydev);
+
+ if (ops->of_xlate)
+ ret = ops->of_xlate(phy, &args);
+ else
+ ret = generic_phy_xlate_offs_flags(phy, &args);
+ if (ret) {
+ debug("of_xlate() failed: %d\n", ret);
+ goto err;
+ }
+
+ return 0;
+
+err:
+ return ret;
+}
+
+int generic_phy_get_by_name(struct udevice *dev, const char *phy_name,
+ struct phy *phy)
+{
+ int index;
+
+ debug("%s(dev=%p, name=%s, phy=%p)\n", __func__, dev, phy_name, phy);
+
+ index = fdt_stringlist_search(gd->fdt_blob, dev_of_offset(dev),
+ "phy-names", phy_name);
+ if (index < 0) {
+ debug("fdt_stringlist_search() failed: %d\n", index);
+ return index;
+ }
+
+ return generic_phy_get_by_index(dev, index, phy);
+}
+
+int generic_phy_init(struct phy *phy)
+{
+ struct phy_ops const *ops = phy_dev_ops(phy->dev);
+
+ return ops->init ? ops->init(phy) : 0;
+}
+
+int generic_phy_reset(struct phy *phy)
+{
+ struct phy_ops const *ops = phy_dev_ops(phy->dev);
+
+ return ops->reset ? ops->reset(phy) : 0;
+}
+
+int generic_phy_exit(struct phy *phy)
+{
+ struct phy_ops const *ops = phy_dev_ops(phy->dev);
+
+ return ops->exit ? ops->exit(phy) : 0;
+}
+
+int generic_phy_power_on(struct phy *phy)
+{
+ struct phy_ops const *ops = phy_dev_ops(phy->dev);
+
+ return ops->power_on ? ops->power_on(phy) : 0;
+}
+
+int generic_phy_power_off(struct phy *phy)
+{
+ struct phy_ops const *ops = phy_dev_ops(phy->dev);
+
+ return ops->power_off ? ops->power_off(phy) : 0;
+}
+
+UCLASS_DRIVER(phy) = {
+ .id = UCLASS_PHY,
+ .name = "phy",
+};
diff --git a/drivers/phy/sandbox-phy.c b/drivers/phy/sandbox-phy.c
new file mode 100644
index 0000000..9ad820c
--- /dev/null
+++ b/drivers/phy/sandbox-phy.c
@@ -0,0 +1,108 @@
+/*
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Written by Jean-Jacques Hiblot <jjhiblot@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <generic-phy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct sandbox_phy_priv {
+ bool initialized;
+ bool on;
+ bool broken;
+};
+
+static int sandbox_phy_power_on(struct phy *phy)
+{
+ struct sandbox_phy_priv *priv = dev_get_priv(phy->dev);
+
+ if (!priv->initialized)
+ return -EIO;
+
+ if (priv->broken)
+ return -EIO;
+
+ priv->on = true;
+
+ return 0;
+}
+
+static int sandbox_phy_power_off(struct phy *phy)
+{
+ struct sandbox_phy_priv *priv = dev_get_priv(phy->dev);
+
+ if (!priv->initialized)
+ return -EIO;
+
+ if (priv->broken)
+ return -EIO;
+
+ /*
+ * for validation purpose, let's says that power off
+ * works only for PHY 0
+ */
+ if (phy->id)
+ return -EIO;
+
+ priv->on = false;
+
+ return 0;
+}
+
+static int sandbox_phy_init(struct phy *phy)
+{
+ struct sandbox_phy_priv *priv = dev_get_priv(phy->dev);
+
+ priv->initialized = true;
+ priv->on = true;
+
+ return 0;
+}
+
+static int sandbox_phy_exit(struct phy *phy)
+{
+ struct sandbox_phy_priv *priv = dev_get_priv(phy->dev);
+
+ priv->initialized = false;
+ priv->on = false;
+
+ return 0;
+}
+
+static int sandbox_phy_probe(struct udevice *dev)
+{
+ struct sandbox_phy_priv *priv = dev_get_priv(dev);
+
+ priv->initialized = false;
+ priv->on = false;
+ priv->broken = fdtdec_get_bool(gd->fdt_blob, dev_of_offset(dev),
+ "broken");
+
+ return 0;
+}
+
+static struct phy_ops sandbox_phy_ops = {
+ .power_on = sandbox_phy_power_on,
+ .power_off = sandbox_phy_power_off,
+ .init = sandbox_phy_init,
+ .exit = sandbox_phy_exit,
+};
+
+static const struct udevice_id sandbox_phy_ids[] = {
+ { .compatible = "sandbox,phy" },
+ { }
+};
+
+U_BOOT_DRIVER(phy_sandbox) = {
+ .name = "phy_sandbox",
+ .id = UCLASS_PHY,
+ .of_match = sandbox_phy_ids,
+ .ops = &sandbox_phy_ops,
+ .probe = sandbox_phy_probe,
+ .priv_auto_alloc_size = sizeof(struct sandbox_phy_priv),
+};
diff --git a/drivers/phy/ti-pipe3-phy.c b/drivers/phy/ti-pipe3-phy.c
new file mode 100644
index 0000000..ed80f0f
--- /dev/null
+++ b/drivers/phy/ti-pipe3-phy.c
@@ -0,0 +1,373 @@
+/*
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Written by Jean-Jacques Hiblot <jjhiblot@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/device.h>
+#include <generic-phy.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <syscon.h>
+#include <regmap.h>
+
+/* PLLCTRL Registers */
+#define PLL_STATUS 0x00000004
+#define PLL_GO 0x00000008
+#define PLL_CONFIGURATION1 0x0000000C
+#define PLL_CONFIGURATION2 0x00000010
+#define PLL_CONFIGURATION3 0x00000014
+#define PLL_CONFIGURATION4 0x00000020
+
+#define PLL_REGM_MASK 0x001FFE00
+#define PLL_REGM_SHIFT 9
+#define PLL_REGM_F_MASK 0x0003FFFF
+#define PLL_REGM_F_SHIFT 0
+#define PLL_REGN_MASK 0x000001FE
+#define PLL_REGN_SHIFT 1
+#define PLL_SELFREQDCO_MASK 0x0000000E
+#define PLL_SELFREQDCO_SHIFT 1
+#define PLL_SD_MASK 0x0003FC00
+#define PLL_SD_SHIFT 10
+#define SET_PLL_GO 0x1
+#define PLL_TICOPWDN BIT(16)
+#define PLL_LDOPWDN BIT(15)
+#define PLL_LOCK 0x2
+#define PLL_IDLE 0x1
+
+/* Software rest for the SATA PLL (in CTRL_CORE_SMA_SW_0 register)*/
+#define SATA_PLL_SOFT_RESET (1<<18)
+
+/* PHY POWER CONTROL Register */
+#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
+#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 0xE
+
+#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK 0xFFC00000
+#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT 0x16
+
+#define OMAP_CTRL_PIPE3_PHY_TX_RX_POWERON 0x3
+#define OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF 0x0
+
+
+#define PLL_IDLE_TIME 100 /* in milliseconds */
+#define PLL_LOCK_TIME 100 /* in milliseconds */
+
+struct omap_pipe3 {
+ void __iomem *pll_ctrl_base;
+ void __iomem *power_reg;
+ void __iomem *pll_reset_reg;
+ struct pipe3_dpll_map *dpll_map;
+};
+
+
+struct pipe3_dpll_params {
+ u16 m;
+ u8 n;
+ u8 freq:3;
+ u8 sd;
+ u32 mf;
+};
+
+struct pipe3_dpll_map {
+ unsigned long rate;
+ struct pipe3_dpll_params params;
+};
+
+static inline u32 omap_pipe3_readl(void __iomem *addr, unsigned offset)
+{
+ return readl(addr + offset);
+}
+
+static inline void omap_pipe3_writel(void __iomem *addr, unsigned offset,
+ u32 data)
+{
+ writel(data, addr + offset);
+}
+
+static struct pipe3_dpll_params *omap_pipe3_get_dpll_params(struct omap_pipe3
+ *pipe3)
+{
+ u32 rate;
+ struct pipe3_dpll_map *dpll_map = pipe3->dpll_map;
+
+ rate = get_sys_clk_freq();
+
+ for (; dpll_map->rate; dpll_map++) {
+ if (rate == dpll_map->rate)
+ return &dpll_map->params;
+ }
+
+ printf("%s: No DPLL configuration for %u Hz SYS CLK\n",
+ __func__, rate);
+ return NULL;
+}
+
+static int omap_pipe3_wait_lock(struct omap_pipe3 *pipe3)
+{
+ u32 val;
+ int timeout = PLL_LOCK_TIME;
+
+ do {
+ mdelay(1);
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_STATUS);
+ if (val & PLL_LOCK)
+ break;
+ } while (--timeout);
+
+ if (!(val & PLL_LOCK)) {
+ printf("%s: DPLL failed to lock\n", __func__);
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+static int omap_pipe3_dpll_program(struct omap_pipe3 *pipe3)
+{
+ u32 val;
+ struct pipe3_dpll_params *dpll_params;
+
+ dpll_params = omap_pipe3_get_dpll_params(pipe3);
+ if (!dpll_params) {
+ printf("%s: Invalid DPLL parameters\n", __func__);
+ return -EINVAL;
+ }
+
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION1);
+ val &= ~PLL_REGN_MASK;
+ val |= dpll_params->n << PLL_REGN_SHIFT;
+ omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION1, val);
+
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION2);
+ val &= ~PLL_SELFREQDCO_MASK;
+ val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
+ omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION2, val);
+
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION1);
+ val &= ~PLL_REGM_MASK;
+ val |= dpll_params->m << PLL_REGM_SHIFT;
+ omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION1, val);
+
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION4);
+ val &= ~PLL_REGM_F_MASK;
+ val |= dpll_params->mf << PLL_REGM_F_SHIFT;
+ omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION4, val);
+
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION3);
+ val &= ~PLL_SD_MASK;
+ val |= dpll_params->sd << PLL_SD_SHIFT;
+ omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION3, val);
+
+ omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_GO, SET_PLL_GO);
+
+ return omap_pipe3_wait_lock(pipe3);
+}
+
+static void omap_control_pipe3_power(struct omap_pipe3 *pipe3, int on)
+{
+ u32 val, rate;
+
+ val = readl(pipe3->power_reg);
+
+ rate = get_sys_clk_freq();
+ rate = rate/1000000;
+
+ if (on) {
+ val &= ~(OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
+ OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK);
+ val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWERON <<
+ OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+ val |= rate <<
+ OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
+ } else {
+ val &= ~OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK;
+ val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF <<
+ OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+ }
+
+ writel(val, pipe3->power_reg);
+}
+
+static int pipe3_init(struct phy *phy)
+{
+ int ret;
+ u32 val;
+ struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
+
+ /* Program the DPLL only if not locked */
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_STATUS);
+ if (!(val & PLL_LOCK)) {
+ ret = omap_pipe3_dpll_program(pipe3);
+ if (ret)
+ return ret;
+ } else {
+ /* else just bring it out of IDLE mode */
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base,
+ PLL_CONFIGURATION2);
+ if (val & PLL_IDLE) {
+ val &= ~PLL_IDLE;
+ omap_pipe3_writel(pipe3->pll_ctrl_base,
+ PLL_CONFIGURATION2, val);
+ ret = omap_pipe3_wait_lock(pipe3);
+ if (ret)
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static int pipe3_power_on(struct phy *phy)
+{
+ struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
+
+ /* Power up the PHY */
+ omap_control_pipe3_power(pipe3, 1);
+
+ return 0;
+}
+
+static int pipe3_power_off(struct phy *phy)
+{
+ struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
+
+ /* Power down the PHY */
+ omap_control_pipe3_power(pipe3, 0);
+
+ return 0;
+}
+
+static int pipe3_exit(struct phy *phy)
+{
+ u32 val;
+ int timeout = PLL_IDLE_TIME;
+ struct omap_pipe3 *pipe3 = dev_get_priv(phy->dev);
+
+ pipe3_power_off(phy);
+
+ /* Put DPLL in IDLE mode */
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_CONFIGURATION2);
+ val |= PLL_IDLE;
+ omap_pipe3_writel(pipe3->pll_ctrl_base, PLL_CONFIGURATION2, val);
+
+ /* wait for LDO and Oscillator to power down */
+ do {
+ mdelay(1);
+ val = omap_pipe3_readl(pipe3->pll_ctrl_base, PLL_STATUS);
+ if ((val & PLL_TICOPWDN) && (val & PLL_LDOPWDN))
+ break;
+ } while (--timeout);
+
+ if (!(val & PLL_TICOPWDN) || !(val & PLL_LDOPWDN)) {
+ error("%s: Failed to power down DPLL: PLL_STATUS 0x%x\n",
+ __func__, val);
+ return -EBUSY;
+ }
+
+ val = readl(pipe3->pll_reset_reg);
+ writel(val | SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
+ mdelay(1);
+ writel(val & ~SATA_PLL_SOFT_RESET, pipe3->pll_reset_reg);
+ return 0;
+}
+
+static void *get_reg(struct udevice *dev, const char *name)
+{
+ struct udevice *syscon;
+ struct regmap *regmap;
+ const fdt32_t *cell;
+ int len, err;
+ void *base;
+
+ err = uclass_get_device_by_phandle(UCLASS_SYSCON, dev,
+ name, &syscon);
+ if (err) {
+ error("unable to find syscon device for %s (%d)\n",
+ name, err);
+ return NULL;
+ }
+
+ regmap = syscon_get_regmap(syscon);
+ if (IS_ERR(regmap)) {
+ error("unable to find regmap for %s (%ld)\n",
+ name, PTR_ERR(regmap));
+ return NULL;
+ }
+
+ cell = fdt_getprop(gd->fdt_blob, dev->of_offset, name,
+ &len);
+ if (len < 2*sizeof(fdt32_t)) {
+ error("offset not available for %s\n", name);
+ return NULL;
+ }
+
+ base = regmap_get_range(regmap, 0);
+ if (!base)
+ return NULL;
+
+ return fdtdec_get_number(cell + 1, 1) + base;
+}
+
+static int pipe3_phy_probe(struct udevice *dev)
+{
+ fdt_addr_t addr;
+ fdt_size_t sz;
+ struct omap_pipe3 *pipe3 = dev_get_priv(dev);
+
+ addr = dev_get_addr_size_index(dev, 2, &sz);
+ if (addr == FDT_ADDR_T_NONE) {
+ error("missing pll ctrl address\n");
+ return -EINVAL;
+ }
+
+ pipe3->pll_ctrl_base = map_physmem(addr, sz, MAP_NOCACHE);
+ if (!pipe3->pll_ctrl_base) {
+ error("unable to remap pll ctrl\n");
+ return -EINVAL;
+ }
+
+ pipe3->power_reg = get_reg(dev, "syscon-phy-power");
+ if (!pipe3->power_reg)
+ return -EINVAL;
+
+ pipe3->pll_reset_reg = get_reg(dev, "syscon-pllreset");
+ if (!pipe3->pll_reset_reg)
+ return -EINVAL;
+
+ pipe3->dpll_map = (struct pipe3_dpll_map *)dev_get_driver_data(dev);
+
+ return 0;
+}
+
+static struct pipe3_dpll_map dpll_map_sata[] = {
+ {12000000, {1000, 7, 4, 6, 0} }, /* 12 MHz */
+ {16800000, {714, 7, 4, 6, 0} }, /* 16.8 MHz */
+ {19200000, {625, 7, 4, 6, 0} }, /* 19.2 MHz */
+ {20000000, {600, 7, 4, 6, 0} }, /* 20 MHz */
+ {26000000, {461, 7, 4, 6, 0} }, /* 26 MHz */
+ {38400000, {312, 7, 4, 6, 0} }, /* 38.4 MHz */
+ { }, /* Terminator */
+};
+
+static const struct udevice_id pipe3_phy_ids[] = {
+ { .compatible = "ti,phy-pipe3-sata", .data = (ulong)&dpll_map_sata },
+ { }
+};
+
+static struct phy_ops pipe3_phy_ops = {
+ .init = pipe3_init,
+ .power_on = pipe3_power_on,
+ .power_off = pipe3_power_off,
+ .exit = pipe3_exit,
+};
+
+U_BOOT_DRIVER(pipe3_phy) = {
+ .name = "pipe3_phy",
+ .id = UCLASS_PHY,
+ .of_match = pipe3_phy_ids,
+ .ops = &pipe3_phy_ops,
+ .probe = pipe3_phy_probe,
+ .priv_auto_alloc_size = sizeof(struct omap_pipe3),
+};
diff --git a/drivers/serial/atmel_usart.c b/drivers/serial/atmel_usart.c
index 7674f97..453f8eb 100644
--- a/drivers/serial/atmel_usart.c
+++ b/drivers/serial/atmel_usart.c
@@ -7,6 +7,7 @@
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <clk.h>
#include <dm.h>
#include <errno.h>
#include <watchdog.h>
@@ -25,6 +26,7 @@
DECLARE_GLOBAL_DATA_PTR;
+#ifndef CONFIG_DM_SERIAL
static void atmel_serial_setbrg_internal(atmel_usart3_t *usart, int id,
int baudrate)
{
@@ -66,7 +68,6 @@
__udelay(100);
}
-#ifndef CONFIG_DM_SERIAL
static void atmel_serial_setbrg(void)
{
atmel_serial_setbrg_internal((atmel_usart3_t *)CONFIG_USART_BASE,
@@ -133,17 +134,47 @@
#endif
#ifdef CONFIG_DM_SERIAL
+enum serial_clk_type {
+ CLK_TYPE_NORMAL = 0,
+ CLK_TYPE_DBGU,
+};
struct atmel_serial_priv {
atmel_usart3_t *usart;
+ ulong usart_clk_rate;
};
+static void _atmel_serial_set_brg(atmel_usart3_t *usart,
+ ulong usart_clk_rate, int baudrate)
+{
+ unsigned long divisor;
+
+ divisor = (usart_clk_rate / 16 + baudrate / 2) / baudrate;
+ writel(USART3_BF(CD, divisor), &usart->brgr);
+}
+
+void _atmel_serial_init(atmel_usart3_t *usart,
+ ulong usart_clk_rate, int baudrate)
+{
+ writel(USART3_BIT(RXDIS) | USART3_BIT(TXDIS), &usart->cr);
+
+ writel((USART3_BF(USART_MODE, USART3_USART_MODE_NORMAL) |
+ USART3_BF(USCLKS, USART3_USCLKS_MCK) |
+ USART3_BF(CHRL, USART3_CHRL_8) |
+ USART3_BF(PAR, USART3_PAR_NONE) |
+ USART3_BF(NBSTOP, USART3_NBSTOP_1)), &usart->mr);
+
+ _atmel_serial_set_brg(usart, usart_clk_rate, baudrate);
+
+ writel(USART3_BIT(RSTRX) | USART3_BIT(RSTTX), &usart->cr);
+ writel(USART3_BIT(RXEN) | USART3_BIT(TXEN), &usart->cr);
+}
+
int atmel_serial_setbrg(struct udevice *dev, int baudrate)
{
struct atmel_serial_priv *priv = dev_get_priv(dev);
- atmel_serial_setbrg_internal(priv->usart, 0 /* ignored */, baudrate);
- atmel_serial_activate(priv->usart);
+ _atmel_serial_set_brg(priv->usart, priv->usart_clk_rate, baudrate);
return 0;
}
@@ -188,10 +219,39 @@
.setbrg = atmel_serial_setbrg,
};
+static int atmel_serial_enable_clk(struct udevice *dev)
+{
+ struct atmel_serial_priv *priv = dev_get_priv(dev);
+ struct clk clk;
+ ulong clk_rate;
+ int ret;
+
+ ret = clk_get_by_index(dev, 0, &clk);
+ if (ret)
+ return -EINVAL;
+
+ if (dev_get_driver_data(dev) == CLK_TYPE_NORMAL) {
+ ret = clk_enable(&clk);
+ if (ret)
+ return ret;
+ }
+
+ clk_rate = clk_get_rate(&clk);
+ if (!clk_rate)
+ return -EINVAL;
+
+ priv->usart_clk_rate = clk_rate;
+
+ clk_free(&clk);
+
+ return 0;
+}
+
static int atmel_serial_probe(struct udevice *dev)
{
struct atmel_serial_platdata *plat = dev->platdata;
struct atmel_serial_priv *priv = dev_get_priv(dev);
+ int ret;
#if CONFIG_IS_ENABLED(OF_CONTROL)
fdt_addr_t addr_base;
@@ -202,14 +262,26 @@
plat->base_addr = (uint32_t)addr_base;
#endif
priv->usart = (atmel_usart3_t *)plat->base_addr;
- atmel_serial_init_internal(priv->usart);
+
+ ret = atmel_serial_enable_clk(dev);
+ if (ret)
+ return ret;
+
+ _atmel_serial_init(priv->usart, priv->usart_clk_rate, gd->baudrate);
return 0;
}
#if CONFIG_IS_ENABLED(OF_CONTROL)
static const struct udevice_id atmel_serial_ids[] = {
- { .compatible = "atmel,at91sam9260-usart" },
+ {
+ .compatible = "atmel,at91sam9260-dbgu",
+ .data = CLK_TYPE_DBGU,
+ },
+ {
+ .compatible = "atmel,at91sam9260-usart",
+ .data = CLK_TYPE_NORMAL,
+ },
{ }
};
#endif
@@ -233,7 +305,7 @@
{
atmel_usart3_t *usart = (atmel_usart3_t *)CONFIG_DEBUG_UART_BASE;
- atmel_serial_setbrg_internal(usart, 0, CONFIG_BAUDRATE);
+ _atmel_serial_init(usart, CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE);
}
static inline void _debug_uart_putc(int ch)
diff --git a/include/configs/at91sam9260ek.h b/include/configs/at91sam9260ek.h
index 379f234..48d7f6a 100644
--- a/include/configs/at91sam9260ek.h
+++ b/include/configs/at91sam9260ek.h
@@ -45,19 +45,6 @@
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO
-#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
-
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED AT91_PIN_PA9 /* this is the power led */
-#define CONFIG_GREEN_LED AT91_PIN_PA6 /* this is the user led */
-
/*
* BOOTP options
@@ -87,10 +74,10 @@
*/
#ifdef CONFIG_AT91SAM9XE
# define CONFIG_SYS_INIT_SP_ADDR \
- (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE)
+ (ATMEL_BASE_SRAM + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#else
# define CONFIG_SYS_INIT_SP_ADDR \
- (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
+ (ATMEL_BASE_SRAM1 + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
/*
@@ -142,18 +129,6 @@
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
#endif
-/* MMC */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
-/* Ethernet */
-#define CONFIG_MACB 1
-#define CONFIG_RMII 1
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_RESET_PHY_R 1
-#define CONFIG_AT91_WANTS_COMMON_PHY
-
/* USB */
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
@@ -200,7 +175,7 @@
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_OFFSET 0xc0000
+#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm"
diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h
index 663c193..e45e4db 100644
--- a/include/configs/at91sam9263ek.h
+++ b/include/configs/at91sam9263ek.h
@@ -45,13 +45,6 @@
* Hardware drivers
*/
#define CONFIG_ATMEL_LEGACY
-#define CONFIG_AT91_GPIO 1
-#define CONFIG_AT91_GPIO_PULLUP 1
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
/* LCD */
#define LCD_BPP LCD_COLOR8
@@ -62,13 +55,6 @@
#define CONFIG_ATMEL_LCD 1
#define CONFIG_ATMEL_LCD_BGR555 1
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED AT91_PIN_PB7 /* the power led */
-#define CONFIG_GREEN_LED AT91_PIN_PB8 /* the user1 led */
-#define CONFIG_YELLOW_LED AT91_PIN_PC29 /* the user2 led */
-
-
/*
* BOOTP options
*/
@@ -88,7 +74,7 @@
#define CONFIG_SYS_SDRAM_SIZE 0x04000000
#define CONFIG_SYS_INIT_SP_ADDR \
- (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
+ (ATMEL_BASE_SRAM1 + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
#define CONFIG_ATMEL_DATAFLASH_SPI
@@ -99,11 +85,6 @@
#define DATAFLASH_TCSS (0x1a << 16)
#define DATAFLASH_TCHS (0x1 << 24)
-/* MMC */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
/* NOR flash, if populated */
#ifdef CONFIG_SYS_USE_NORFLASH
#define CONFIG_SYS_FLASH_CFI 1
@@ -249,9 +230,6 @@
#endif
/* Ethernet */
-#define CONFIG_MACB 1
-#define CONFIG_RMII 1
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R 1
#define CONFIG_AT91_WANTS_COMMON_PHY
@@ -287,7 +265,7 @@
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_OFFSET 0xc0000
+#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm"
diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
index a62b70b..010ebdb 100644
--- a/include/configs/at91sam9m10g45ek.h
+++ b/include/configs/at91sam9m10g45ek.h
@@ -30,13 +30,6 @@
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO
-#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
/* LCD */
#define LCD_BPP LCD_COLOR8
@@ -49,12 +42,6 @@
/* board specific(not enough SRAM) */
#define CONFIG_AT91SAM9G45_LCD_BASE 0x73E00000
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED AT91_PIN_PD31 /* this is the user1 led */
-#define CONFIG_GREEN_LED AT91_PIN_PD0 /* this is the user2 led */
-
-
/*
* BOOTP options
*/
@@ -75,7 +62,7 @@
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* NAND flash */
#ifdef CONFIG_CMD_NAND
@@ -92,24 +79,10 @@
#endif
-/* MMC */
-
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
/* Ethernet */
-#define CONFIG_MACB
-#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
-/* USB */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
-
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
@@ -118,7 +91,7 @@
#ifdef CONFIG_SYS_USE_NANDFLASH
/* bootstrap + u-boot + env in nandflash */
#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0xc0000
+#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000
diff --git a/include/configs/at91sam9n12ek.h b/include/configs/at91sam9n12ek.h
index dd49f4e..e7b9ad2 100644
--- a/include/configs/at91sam9n12ek.h
+++ b/include/configs/at91sam9n12ek.h
@@ -28,14 +28,6 @@
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
-/* general purpose I/O */
-#define CONFIG_AT91_GPIO
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
-
/* LCD */
#define LCD_BPP LCD_COLOR16
#define LCD_OUTPUT_BPP 24
@@ -45,7 +37,6 @@
#define CONFIG_ATMEL_HLCD
#define CONFIG_ATMEL_LCD_RGB565
-
/*
* BOOTP options
*/
@@ -69,14 +60,11 @@
* that address while providing maximum stack area below.
*/
# define CONFIG_SYS_INIT_SP_ADDR \
- (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE)
+ (ATMEL_BASE_SRAM + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
#ifdef CONFIG_CMD_SF
-#define CONFIG_ATMEL_SPI
#define CONFIG_SF_DEFAULT_SPEED 30000000
-#define CONFIG_ENV_SPI_MODE SPI_MODE_3
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
#endif
/* NAND flash */
@@ -115,11 +103,6 @@
"bootargs_nand=rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs rw\0"\
"bootargs_mmc=root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait\0"
-/* MMC */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
/* Ethernet */
#define CONFIG_KS8851_MLL
#define CONFIG_KS8851_MLL_BASEADDR 0x30000000 /* use NCS2 */
@@ -156,7 +139,7 @@
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0xc0000
+#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND \
diff --git a/include/configs/at91sam9rlek.h b/include/configs/at91sam9rlek.h
index 31a7cb1..7dcf791 100644
--- a/include/configs/at91sam9rlek.h
+++ b/include/configs/at91sam9rlek.h
@@ -29,18 +29,11 @@
#define CONFIG_INITRD_TAG 1
#define CONFIG_ATMEL_LEGACY
-#define CONFIG_AT91_GPIO 1
-#define CONFIG_AT91_GPIO_PULLUP 1
/*
* Hardware drivers
*/
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
-
/* LCD */
#define LCD_BPP LCD_COLOR8
#define CONFIG_LCD_LOGO 1
@@ -52,13 +45,6 @@
/* Let board_init_f handle the framebuffer allocation */
#undef CONFIG_FB_ADDR
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED AT91_PIN_PD14 /* this is the power led */
-#define CONFIG_GREEN_LED AT91_PIN_PD15 /* this is the user1 led */
-#define CONFIG_YELLOW_LED AT91_PIN_PD16 /* this is the user2 led */
-
-
/*
* Command line configuration.
*/
@@ -71,7 +57,7 @@
#define CONFIG_SYS_SDRAM_SIZE 0x04000000
#define CONFIG_SYS_INIT_SP_ADDR \
- (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE)
+ (ATMEL_BASE_SRAM + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
#define CONFIG_ATMEL_DATAFLASH_SPI
@@ -97,12 +83,6 @@
#endif
-/* MMC */
-
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
/* Ethernet - not present */
/* USB - not supported */
@@ -130,7 +110,7 @@
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_OFFSET 0xc0000
+#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x600000; " \
diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h
index ff0a78b..52a051a 100644
--- a/include/configs/at91sam9x5ek.h
+++ b/include/configs/at91sam9x5ek.h
@@ -26,12 +26,6 @@
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
/* LCD */
#define LCD_BPP LCD_COLOR16
@@ -67,11 +61,10 @@
#define CONFIG_SYS_SDRAM_SIZE 0x08000000 /* 128 megs */
#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
#ifdef CONFIG_CMD_SF
-#define CONFIG_ATMEL_SPI
#define CONFIG_SF_DEFAULT_SPEED 30000000
#endif
@@ -104,23 +97,9 @@
#define CONFIG_CMD_UBIFS
#endif
-/* MMC */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
-/* Ethernet */
-#define CONFIG_MACB
-#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_MACB_SEARCH_PHY
-
/* USB */
#ifdef CONFIG_CMD_USB
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
-#else
+#ifndef CONFIG_USB_EHCI
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
@@ -139,7 +118,7 @@
#ifdef CONFIG_SYS_USE_NANDFLASH
/* bootstrap + u-boot + env + linux in nandflash */
#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0xc0000
+#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
#define CONFIG_BOOTCOMMAND "nand read " \
diff --git a/include/configs/sama5d2_xplained.h b/include/configs/sama5d2_xplained.h
index ea28fce..f044f0e 100644
--- a/include/configs/sama5d2_xplained.h
+++ b/include/configs/sama5d2_xplained.h
@@ -20,10 +20,10 @@
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_INIT_SP_ADDR 0x210000
+#define CONFIG_SYS_INIT_SP_ADDR 0x218000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
@@ -38,21 +38,10 @@
/* NAND flash */
#undef CONFIG_CMD_NAND
-/* USB device */
-#define CONFIG_USB_ETHER
-#define CONFIG_USB_ETH_RNDIS
-#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2 XPlained"
-
/* I2C */
#define AT24MAC_ADDR 0x5c
#define AT24MAC_REG 0x9a
-/* Ethernet Hardware */
-#define CONFIG_MACB
-#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_MACB_SEARCH_PHY
-
/* LCD */
#ifdef CONFIG_LCD
@@ -84,7 +73,7 @@
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
-#define CONFIG_SPL_MAX_SIZE 0x10000
+#define CONFIG_SPL_MAX_SIZE 0x18000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
@@ -100,7 +89,7 @@
#elif CONFIG_SYS_USE_SERIALFLASH
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
#endif
diff --git a/include/dm/uclass-id.h b/include/dm/uclass-id.h
index 4e7cc93..1f7e32c 100644
--- a/include/dm/uclass-id.h
+++ b/include/dm/uclass-id.h
@@ -56,6 +56,7 @@
UCLASS_PCH, /* x86 platform controller hub */
UCLASS_PCI, /* PCI bus */
UCLASS_PCI_GENERIC, /* Generic PCI bus device */
+ UCLASS_PHY, /* Physical Layer (PHY) device */
UCLASS_PINCONFIG, /* Pin configuration node device */
UCLASS_PINCTRL, /* Pinctrl (pin muxing/configuration) device */
UCLASS_PMIC, /* PMIC I/O device */
diff --git a/include/generic-phy.h b/include/generic-phy.h
new file mode 100644
index 0000000..d8cf0c9
--- /dev/null
+++ b/include/generic-phy.h
@@ -0,0 +1,224 @@
+/*
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Written by Jean-Jacques Hiblot <jjhiblot@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __GENERIC_PHY_H
+#define __GENERIC_PHY_H
+
+
+/**
+ * struct phy - A handle to (allowing control of) a single phy port.
+ *
+ * Clients provide storage for phy handles. The content of the structure is
+ * managed solely by the PHY API and PHY drivers. A phy struct is
+ * initialized by "get"ing the phy struct. The phy struct is passed to all
+ * other phy APIs to identify which PHY port to operate upon.
+ *
+ * @dev: The device which implements the PHY port.
+ * @id: The PHY ID within the provider.
+ *
+ */
+struct phy {
+ struct udevice *dev;
+ unsigned long id;
+};
+
+/*
+ * struct udevice_ops - set of function pointers for phy operations
+ * @init: operation to be performed for initializing phy (optional)
+ * @exit: operation to be performed while exiting (optional)
+ * @reset: reset the phy (optional).
+ * @power_on: powering on the phy (optional)
+ * @power_off: powering off the phy (optional)
+ */
+struct phy_ops {
+ /**
+ * of_xlate - Translate a client's device-tree (OF) phy specifier.
+ *
+ * The PHY core calls this function as the first step in implementing
+ * a client's generic_phy_get_by_*() call.
+ *
+ * If this function pointer is set to NULL, the PHY core will use a
+ * default implementation, which assumes #phy-cells = <0> or
+ * #phy-cells = <1>, and in the later case that the DT cell
+ * contains a simple integer PHY port ID.
+ *
+ * @phy: The phy struct to hold the translation result.
+ * @args: The phy specifier values from device tree.
+ * @return 0 if OK, or a negative error code.
+ */
+ int (*of_xlate)(struct phy *phy,
+ struct fdtdec_phandle_args *args);
+
+ /**
+ * init - initialize the hardware.
+ *
+ * Hardware intialization should not be done in during probe() but
+ * should be implemented in this init() function. It could be starting
+ * PLL, taking a controller out of reset, routing, etc. This function
+ * is typically called only once per PHY port.
+ * If power_on() is not implemented, it must power up the phy.
+ *
+ * @phy: the PHY port to initialize
+ * @return 0 if OK, or a negative error code.
+ */
+ int (*init)(struct phy *phy);
+
+ /**
+ * exit - de-initialize the PHY device
+ *
+ * Hardware de-intialization should be done here. Every step done in
+ * init() should be undone here.
+ * This could be used to suspend the phy to reduce power consumption or
+ * to put the phy in a known condition before booting the OS (though it
+ * is NOT called automatically before booting the OS)
+ * If power_off() is not implemented, it must power down the phy.
+ *
+ * @phy: PHY port to be de-initialized
+ * @return 0 if OK, or a negative error code
+ */
+ int (*exit)(struct phy *phy);
+
+ /**
+ * reset - resets a PHY device without shutting down
+ *
+ * @phy: PHY port to be reset
+ *
+ * During runtime, the PHY may need to be reset in order to
+ * re-establish connection etc without being shut down or exit.
+ *
+ * @return 0 if OK, or a negative error code
+ */
+ int (*reset)(struct phy *phy);
+
+ /**
+ * power_on - power on a PHY device
+ *
+ * @phy: PHY port to be powered on
+ *
+ * During runtime, the PHY may need to be powered on or off several
+ * times. This function is used to power on the PHY. It relies on the
+ * setup done in init(). If init() is not implemented, it must take care
+ * of setting up the context (PLLs, ...)
+ *
+ * @return 0 if OK, or a negative error code
+ */
+ int (*power_on)(struct phy *phy);
+
+ /**
+ * power_off - power off a PHY device
+ *
+ * @phy: PHY port to be powered off
+ *
+ * During runtime, the PHY may need to be powered on or off several
+ * times. This function is used to power off the PHY. Except if
+ * init()/deinit() are not implemented, it must not de-initialize
+ * everything.
+ *
+ * @return 0 if OK, or a negative error code
+ */
+ int (*power_off)(struct phy *phy);
+};
+
+
+/**
+ * generic_phy_init() - initialize the PHY port
+ *
+ * @phy: the PHY port to initialize
+ * @return 0 if OK, or a negative error code
+ */
+int generic_phy_init(struct phy *phy);
+
+/**
+ * generic_phy_init() - de-initialize the PHY device
+ *
+ * @phy: PHY port to be de-initialized
+ * @return 0 if OK, or a negative error code
+ */
+int generic_phy_exit(struct phy *phy);
+
+/**
+ * generic_phy_reset() - resets a PHY device without shutting down
+ *
+ * @phy: PHY port to be reset
+ *@return 0 if OK, or a negative error code
+ */
+int generic_phy_reset(struct phy *phy);
+
+/**
+ * generic_phy_power_on() - power on a PHY device
+ *
+ * @phy: PHY port to be powered on
+ * @return 0 if OK, or a negative error code
+ */
+int generic_phy_power_on(struct phy *phy);
+
+/**
+ * generic_phy_power_off() - power off a PHY device
+ *
+ * @phy: PHY port to be powered off
+ * @return 0 if OK, or a negative error code
+ */
+int generic_phy_power_off(struct phy *phy);
+
+
+/**
+ * generic_phy_get_by_index() - Get a PHY device by integer index.
+ *
+ * @user: the client device
+ * @index: The index in the list of available PHYs
+ * @phy: A pointer to the PHY port
+ *
+ * This looks up a PHY device for a client device based on its position in the
+ * list of the possible PHYs.
+ *
+ * example:
+ * usb1: usb_otg_ss@xxx {
+ * compatible = "xxx";
+ * reg = <xxx>;
+ * .
+ * .
+ * phys = <&usb2_phy>, <&usb3_phy>;
+ * .
+ * .
+ * };
+ * the USB2 phy can be accessed by passing index '0' and the USB3 phy can
+ * be accessed by passing index '1'
+ *
+ * @return 0 if OK, or a negative error code
+ */
+int generic_phy_get_by_index(struct udevice *user, int index,
+ struct phy *phy);
+
+/**
+ * generic_phy_get_by_name() - Get a PHY device by its name.
+ *
+ * @user: the client device
+ * @phy_name: The name of the PHY in the list of possible PHYs
+ * @phy: A pointer to the PHY port
+ *
+ * This looks up a PHY device for a client device in the
+ * list of the possible PHYs based on its name.
+ *
+ * example:
+ * usb1: usb_otg_ss@xxx {
+ * compatible = "xxx";
+ * reg = <xxx>;
+ * .
+ * .
+ * phys = <&usb2_phy>, <&usb3_phy>;
+ * phy-names = "usb2phy", "usb3phy";
+ * .
+ * .
+ * };
+ * the USB3 phy can be accessed using "usb3phy", and USB2 by using "usb2phy"
+ *
+ * @return 0 if OK, or a negative error code
+ */
+int generic_phy_get_by_name(struct udevice *user, const char *phy_name,
+ struct phy *phy);
+
+#endif /*__GENERIC_PHY_H */
diff --git a/test/dm/Makefile b/test/dm/Makefile
index b15f1d0..513c456 100644
--- a/test/dm/Makefile
+++ b/test/dm/Makefile
@@ -24,6 +24,7 @@
obj-$(CONFIG_DM_MAILBOX) += mailbox.o
obj-$(CONFIG_DM_MMC) += mmc.o
obj-$(CONFIG_DM_PCI) += pci.o
+obj-$(CONFIG_PHY) += phy.o
obj-$(CONFIG_POWER_DOMAIN) += power-domain.o
obj-$(CONFIG_DM_PWM) += pwm.o
obj-$(CONFIG_RAM) += ram.o
diff --git a/test/dm/phy.c b/test/dm/phy.c
new file mode 100644
index 0000000..811045f
--- /dev/null
+++ b/test/dm/phy.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ * Written by Jean-Jacques Hiblot <jjhiblot@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <generic-phy.h>
+#include <dm/test.h>
+#include <test/ut.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Base test of the phy uclass */
+static int dm_test_phy_base(struct unit_test_state *uts)
+{
+ struct udevice *dev;
+ struct phy phy1_method1;
+ struct phy phy1_method2;
+ struct phy phy2;
+ struct phy phy3;
+ struct udevice *parent;
+
+ /* Get the device using the phy device*/
+ ut_assertok(uclass_get_device_by_name(UCLASS_SIMPLE_BUS,
+ "gen_phy_user", &parent));
+ /*
+ * Get the same phy port in 2 different ways and compare.
+ */
+ ut_assertok(generic_phy_get_by_name(parent, "phy1", &phy1_method1))
+ ut_assertok(generic_phy_get_by_index(parent, 0, &phy1_method2))
+ ut_asserteq(phy1_method1.id, phy1_method2.id);
+
+ /*
+ * Get the second phy port. Check that the same phy provider (device)
+ * provides this 2nd phy port, but that the IDs are different
+ */
+ ut_assertok(generic_phy_get_by_name(parent, "phy2", &phy2))
+ ut_asserteq_ptr(phy1_method2.dev, phy2.dev);
+ ut_assert(phy1_method1.id != phy2.id);
+
+ /*
+ * Get the third phy port. Check that the phy provider is different
+ */
+ ut_assertok(generic_phy_get_by_name(parent, "phy3", &phy3))
+ ut_assert(phy2.dev != phy3.dev);
+
+ /* Try to get a non-existing phy */
+ ut_asserteq(-ENODEV, uclass_get_device(UCLASS_PHY, 3, &dev));
+ ut_assert(generic_phy_get_by_name(parent, "phy_not_existing",
+ &phy1_method1) < 0)
+
+ return 0;
+}
+DM_TEST(dm_test_phy_base, DM_TESTF_SCAN_PDATA | DM_TESTF_SCAN_FDT);
+
+/* Test of the phy uclass using the sandbox phy driver operations */
+static int dm_test_phy_ops(struct unit_test_state *uts)
+{
+ struct phy phy1;
+ struct phy phy2;
+ struct phy phy3;
+ struct udevice *parent;
+
+ ut_assertok(uclass_get_device_by_name(UCLASS_SIMPLE_BUS,
+ "gen_phy_user", &parent));
+
+ ut_assertok(generic_phy_get_by_name(parent, "phy1", &phy1));
+ ut_assertok(generic_phy_get_by_name(parent, "phy2", &phy2));
+ ut_assertok(generic_phy_get_by_name(parent, "phy3", &phy3));
+
+ /* test normal operations */
+ ut_assertok(generic_phy_init(&phy1));
+ ut_assertok(generic_phy_power_on(&phy1));
+ ut_assertok(generic_phy_power_off(&phy1));
+
+ /*
+ * test operations after exit().
+ * The sandbox phy driver does not allow it.
+ */
+ ut_assertok(generic_phy_exit(&phy1));
+ ut_assert(generic_phy_power_on(&phy1) != 0);
+ ut_assert(generic_phy_power_off(&phy1) != 0);
+
+ /*
+ * test normal operations again (after re-init)
+ */
+ ut_assertok(generic_phy_init(&phy1));
+ ut_assertok(generic_phy_power_on(&phy1));
+ ut_assertok(generic_phy_power_off(&phy1));
+
+ /*
+ * test calling unimplemented feature.
+ * The call is expected to succeed
+ */
+ ut_assertok(generic_phy_reset(&phy1));
+
+ /* PHY2 has a known problem with power off */
+ ut_assertok(generic_phy_init(&phy2));
+ ut_assertok(generic_phy_power_on(&phy2));
+ ut_assert(generic_phy_power_off(&phy2) == -EIO);
+
+ /* PHY3 has a known problem with power off and power on*/
+ ut_assertok(generic_phy_init(&phy3));
+ ut_assert(generic_phy_power_off(&phy3) == -EIO);
+ ut_assert(generic_phy_power_off(&phy3) == -EIO);
+
+ return 0;
+}
+DM_TEST(dm_test_phy_ops, DM_TESTF_SCAN_PDATA | DM_TESTF_SCAN_FDT);