[PATCH] Add AMCC PPC405EZ support
This patch adds support for the new AMCC 405EZ PPC. It is in
preparation for the AMCC Acadia board support.
Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index 24b30df..a50d66e 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -699,7 +699,9 @@
#endif /* CONFIG_IOP480 */
/*****************************************************************************/
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_405) || defined(CONFIG_405EP)
+#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
+ defined(CONFIG_405)
/*----------------------------------------------------------------------- */
/* Clear and set up some registers. */
/*----------------------------------------------------------------------- */
@@ -727,13 +729,13 @@
/*----------------------------------------------------------------------- */
/* Enable two 128MB cachable regions. */
/*----------------------------------------------------------------------- */
- addis r4,r0,0x8000
- addi r4,r4,0x0001
+ lis r4,0x8000
+ ori r4,r4,0x0001
mticcr r4 /* instruction cache */
isync
- addis r4,r0,0x0000
- addi r4,r4,0x0000
+ lis r4,0x0000
+ ori r4,r4,0x0000
mtdccr r4 /* data cache */
#if !(defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR))
@@ -755,6 +757,70 @@
#endif /* CONFIG_405EP */
#if defined(CFG_OCM_DATA_ADDR) && defined(CFG_OCM_DATA_SIZE)
+/* test-only... (clean up later when NAND booting is supported) */
+#if defined(CONFIG_405EZ)
+ /********************************************************************
+ * Setup OCM - On Chip Memory - PPC405EZ uses OCM Controller V2
+ *******************************************************************/
+ /*
+ * We can map the OCM on the PLB3, so map it at
+ * CFG_OCM_DATA_ADDR + 0x8000
+ */
+ lis r3,CFG_OCM_DATA_ADDR@h /* OCM location */
+ ori r3,r3,CFG_OCM_DATA_ADDR@l
+ ori r3,r3,0x8270 /* 32K Offset, 16K for Bank 1, R/W/Enable */
+ mtdcr ocmplb3cr1,r3 /* Set PLB Access */
+ ori r3,r3,0x4000 /* Add 0x4000 for bank 2 */
+ mtdcr ocmplb3cr2,r3 /* Set PLB Access */
+ isync
+
+ lis r3,CFG_OCM_DATA_ADDR@h /* OCM location */
+ ori r3,r3,CFG_OCM_DATA_ADDR@l
+ ori r3,r3,0x0270 /* 16K for Bank 1, R/W/Enable */
+ mtdcr ocmdscr1, r3 /* Set Data Side */
+ mtdcr ocmiscr1, r3 /* Set Instruction Side */
+ ori r3,r3,0x4000 /* Add 0x4000 for bank 2 */
+ mtdcr ocmdscr2, r3 /* Set Data Side */
+ mtdcr ocmiscr2, r3 /* Set Instruction Side */
+ addis r3,0,0x0800 /* OCM Data Parity Disable - 1 Wait State */
+ mtdcr ocmdsisdpc,r4
+
+ isync
+
+#if defined(CONFIG_NAND_SPL)
+ /*
+ * 405EZ can boot from NAND Flash.
+ * If we are booting the SPL (Pre-loader), copy code from
+ * the mapped 4K NAND Flash to the OCM
+ */
+ li r4,(CFG_NAND_BOOT_SPL_SIZE >> 2) - 1
+ mtctr r4
+ lis r2,CFG_NAND_BOOT_SPL_SRC@h
+ ori r2,r2,CFG_NAND_BOOT_SPL_SRC@l
+ lis r3,CFG_NAND_BOOT_SPL_DST@h
+ ori r3,r3,CFG_NAND_BOOT_SPL_DST@l
+spl_loop:
+ lwzu r4,4(r2)
+ stwu r4,4(r3)
+ bdnz spl_loop
+
+ /*
+ * Jump to code in OCM Ram
+ */
+ bl 00f
+00: mflr r10
+ lis r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@h
+ ori r3,r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@l
+ sub r10,r10,r3
+ addi r10,r10,28
+ mtlr r10
+ blr
+start_ram:
+ sync
+ isync
+#endif
+#else
+/* ...test-only */
/********************************************************************
* Setup OCM - On Chip Memory
*******************************************************************/
@@ -774,6 +840,7 @@
addis r4, 0, 0xC000 /* OCM data area enabled */
mtdcr ocmdscntl, r4
isync
+#endif /* CONFIG_405EZ */
#endif
/*----------------------------------------------------------------------- */