configs: ti_armv7_keystone2: start using armv7_common
Try to maintain as much commonality by conditionally including stuff
in armv7_common as necessary and removing the common defines from
keystone2 header.
Note: as part of this change, all keystone2 platforms will now start
using the generic u-boot prompt instead of the custom prompt.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/include/configs/ti_armv7_keystone2.h b/include/configs/ti_armv7_keystone2.h
index 66412c3..fb5ca59 100644
--- a/include/configs/ti_armv7_keystone2.h
+++ b/include/configs/ti_armv7_keystone2.h
@@ -14,10 +14,7 @@
/* U-Boot Build Configuration */
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 2nd stage loader */
-#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_SYS_THUMB_BUILD
/* SoC Configuration */
#define CONFIG_ARCH_CPU_INIT
@@ -28,11 +25,9 @@
/* Memory Configuration */
#define CONFIG_NR_DRAM_BANKS 2
-#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define CONFIG_SYS_LPAE_SDRAM_BASE 0x800000000
#define CONFIG_MAX_RAM_BANK_SIZE (2 << 30) /* 2GB */
#define CONFIG_STACKSIZE (512 << 10) /* 512 KiB */
-#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* 4 MiB */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \
GENERATED_GBL_DATA_SIZE)
@@ -49,15 +44,10 @@
#define CONFIG_SPL_STACK (CONFIG_SYS_SPL_MALLOC_START + \
CONFIG_SYS_SPL_MALLOC_SIZE + \
CONFIG_SPL_STACK_SIZE - 4)
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_SPL_PAD_TO
-#define CONFIG_SPL_FRAMEWORK
/* UART Configuration */
#define CONFIG_SYS_NS16550
@@ -68,13 +58,10 @@
#define CONFIG_SYS_NS16550_COM2 KS2_UART1_BASE
#define CONFIG_SYS_NS16550_CLK clk_get_rate(KS2_CLK1_6)
#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
/* SPI Configuration */
-#define CONFIG_SPI
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_DAVINCI_SPI
-#define CONFIG_CMD_SPI
#define CONFIG_SYS_SPI_CLK clk_get_rate(KS2_CLK1_6)
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
@@ -148,7 +135,6 @@
#define CONFIG_AEMIF_CNTRL_BASE KS2_AEMIF_CNTRL_BASE
/* I2C Configuration */
-#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_DAVINCI
#define CONFIG_SYS_DAVINCI_I2C_SPEED 100000
#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */
@@ -185,7 +171,6 @@
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x100000
#define CONFIG_MTD_PARTITIONS
-#define CONFIG_MTD_DEVICE
#define CONFIG_RBTREE
#define CONFIG_LZO
#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
@@ -198,8 +183,6 @@
#define CONFIG_USB_XHCI_DWC3
#define CONFIG_USB_XHCI_KEYSTONE
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION
#define CONFIG_FS_FAT
#define CONFIG_SYS_CACHELINE_SIZE 64
@@ -209,39 +192,25 @@
#define CONFIG_USB_PHY_CFG_BASE KS2_USB_PHY_CFG_BASE
/* U-Boot command configuration */
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_NAND
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_CMD_SF
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_FS_GENERIC
/* U-Boot general configuration */
-#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_MISC_INIT_R
-#define CONFIG_SYS_CBSIZE 1024
-#define CONFIG_SYS_PBSIZE 2048
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
#define CONFIG_TIMESTAMP
/* EDMA3 */
#define CONFIG_TI_EDMA3
-#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS \
@@ -302,14 +271,26 @@
#define CONFIG_BOOTARGS \
/* Linux interfacing */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_SYS_BARGSIZE 1024
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x08000000)
-#define CONFIG_SUPPORT_RAW_INITRD
+/* Now for the remaining common defines */
+#include <configs/ti_armv7_common.h>
+
+/* We wont be loading up OS from SPL for now.. */
+#undef CONFIG_SPL_OS_BOOT
+
+/* We do not have MMC support.. yet.. */
+#undef CONFIG_SPL_LIBDISK_SUPPORT
+#undef CONFIG_SPL_MMC_SUPPORT
+#undef CONFIG_SPL_FAT_SUPPORT
+#undef CONFIG_SPL_EXT_SUPPORT
+#undef CONFIG_MMC
+#undef CONFIG_GENERIC_MMC
+#undef CONFIG_CMD_MMC
+
+/* And no support for GPIO, yet.. */
+#undef CONFIG_SPL_GPIO_SUPPORT
+#undef CONFIG_CMD_GPIO
/* we may include files below only after all above definitions */
#include <asm/arch/hardware.h>