net: keystone_net: add support for NETCP v1.5
Currently the network driver is used only by k2hk evm board.
The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e
contain NETCP v1.5. So driver should be able to work with such kind
of NETCP. This commit adds this opportunity. The main difference in
masks and some registers, the logic is the same, so only definitions
should be changed. To differentiate between versions add KS2_NETCP_V1_0
and KS2_NETCP_V1_5. Also remove unused and no more needed defines.
The port number is specific for each board so move this parameter to
configuration.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
diff --git a/arch/arm/include/asm/arch-keystone/emac_defs.h b/arch/arm/include/asm/arch-keystone/emac_defs.h
index 47e0ada..3450246 100644
--- a/arch/arm/include/asm/arch-keystone/emac_defs.h
+++ b/arch/arm/include/asm/arch-keystone/emac_defs.h
@@ -13,20 +13,44 @@
#include <asm/arch/hardware.h>
#include <asm/io.h>
+/* EMAC */
+#ifdef KS2_NETCP_V1_0
+
#define EMAC_EMACSL_BASE_ADDR (KS2_PASS_BASE + 0x00090900)
#define EMAC_MDIO_BASE_ADDR (KS2_PASS_BASE + 0x00090300)
#define EMAC_SGMII_BASE_ADDR (KS2_PASS_BASE + 0x00090100)
+#define DEVICE_EMACSL_BASE(x) (EMAC_EMACSL_BASE_ADDR + (x)*0x040)
+
+/* Register offsets */
+#define CPGMACSL_REG_CTL 0x04
+#define CPGMACSL_REG_STATUS 0x08
+#define CPGMACSL_REG_RESET 0x0c
+#define CPGMACSL_REG_MAXLEN 0x10
+
+#elif defined KS2_NETCP_V1_5
+
+#define CPGMACSL_REG_RX_PRI_MAP 0x020
+#define EMAC_EMACSL_BASE_ADDR (KS2_PASS_BASE + 0x00222000)
+#define EMAC_MDIO_BASE_ADDR (KS2_PASS_BASE + 0x00200f00)
+#define EMAC_SGMII_BASE_ADDR (KS2_PASS_BASE + 0x00200100)
+#define DEVICE_EMACSL_BASE(x) (EMAC_EMACSL_BASE_ADDR + (x) * 0x1000)
+
+/* Register offsets */
+#define CPGMACSL_REG_CTL 0x330
+#define CPGMACSL_REG_STATUS 0x334
+#define CPGMACSL_REG_RESET 0x338
+#define CPGMACSL_REG_MAXLEN 0x024
+
+#endif
#define KEYSTONE2_EMAC_GIG_ENABLE
#define MAC_ID_BASE_ADDR (KS2_DEVICE_STATE_CTRL_BASE + 0x110)
-#ifdef CONFIG_SOC_K2HK
/* MDIO module input frequency */
#define EMAC_MDIO_BUS_FREQ (clk_get_rate(pass_pll_clk))
/* MDIO clock output frequency */
#define EMAC_MDIO_CLOCK_FREQ 1000000 /* 1.0 MHz */
-#endif
/* MII Status Register */
#define MII_STATUS_REG 1
@@ -86,17 +110,8 @@
#define GMACSL_RET_WARN_MAXLEN_TOO_BIG -3
#define GMACSL_RET_CONFIG_FAIL_RESET_ACTIVE -4
-/* Register offsets */
-#define CPGMACSL_REG_ID 0x00
-#define CPGMACSL_REG_CTL 0x04
-#define CPGMACSL_REG_STATUS 0x08
-#define CPGMACSL_REG_RESET 0x0c
-#define CPGMACSL_REG_MAXLEN 0x10
-#define CPGMACSL_REG_BOFF 0x14
-#define CPGMACSL_REG_RX_PAUSE 0x18
-#define CPGMACSL_REG_TX_PAURSE 0x1c
-#define CPGMACSL_REG_EM_CTL 0x20
-#define CPGMACSL_REG_PRI 0x24
+/* EMAC SL register definitions */
+#define DEVICE_EMACSL_RESET_POLL_COUNT 100
/* Soft reset register values */
#define CPGMAC_REG_RESET_VAL_RESET_MASK (1 << 0)
@@ -105,6 +120,7 @@
/* Maxlen register values */
#define CPGMAC_REG_MAXLEN_LEN 0x3fff
+/* CPSW */
/* Control bitfields */
#define CPSW_CTL_P2_PASS_PRI_TAGGED (1 << 5)
#define CPSW_CTL_P1_PASS_PRI_TAGGED (1 << 4)
@@ -113,24 +129,39 @@
#define CPSW_CTL_VLAN_AWARE (1 << 1)
#define CPSW_CTL_FIFO_LOOPBACK (1 << 0)
-#define DEVICE_CPSW_NUM_PORTS 5 /* 5 switch ports */
-#define DEVICE_CPSW_BASE (0x02090800)
-#define target_get_switch_ctl() CPSW_CTL_P0_ENABLE /* Enable port 0 */
-#define SWITCH_MAX_PKT_SIZE 9000
+#define DEVICE_CPSW_NUM_PORTS CONFIG_KSNET_CPSW_NUM_PORTS
+#define DEVICE_N_GMACSL_PORTS (DEVICE_CPSW_NUM_PORTS - 1)
-/* Register offsets */
-#define CPSW_REG_CTL 0x004
-#define CPSW_REG_STAT_PORT_EN 0x00c
-#define CPSW_REG_MAXLEN 0x040
-#define CPSW_REG_ALE_CONTROL 0x608
-#define CPSW_REG_ALE_PORTCTL(x) (0x640 + (x)*4)
+#ifdef KS2_NETCP_V1_0
-/* Register values */
-#define CPSW_REG_VAL_STAT_ENABLE_ALL 0xf
+#define DEVICE_CPSW_BASE (KS2_PASS_BASE + 0x00090800)
+#define CPSW_REG_CTL 0x004
+#define CPSW_REG_STAT_PORT_EN 0x00c
+#define CPSW_REG_MAXLEN 0x040
+#define CPSW_REG_ALE_CONTROL 0x608
+#define CPSW_REG_ALE_PORTCTL(x) (0x640 + (x)*4)
+#define CPSW_REG_VAL_STAT_ENABLE_ALL 0xf
+
+#elif defined KS2_NETCP_V1_5
+
+#define DEVICE_CPSW_BASE (KS2_PASS_BASE + 0x00220000)
+#define CPSW_REG_CTL 0x00004
+#define CPSW_REG_STAT_PORT_EN 0x00014
+#define CPSW_REG_MAXLEN 0x01024
+#define CPSW_REG_ALE_CONTROL 0x1e008
+#define CPSW_REG_ALE_PORTCTL(x) (0x1e040 + (x) * 4)
+#define CPSW_REG_VAL_STAT_ENABLE_ALL 0x1ff
+
+#endif
+
#define CPSW_REG_VAL_ALE_CTL_RESET_AND_ENABLE ((u_int32_t)0xc0000000)
#define CPSW_REG_VAL_ALE_CTL_BYPASS ((u_int32_t)0x00000010)
#define CPSW_REG_VAL_PORTCTL_FORWARD_MODE 0x3
+#define target_get_switch_ctl() CPSW_CTL_P0_ENABLE /* Enable port 0 */
+#define SWITCH_MAX_PKT_SIZE 9000
+
+/* SGMII */
#define SGMII_REG_STATUS_LOCK BIT(4)
#define SGMII_REG_STATUS_LINK BIT(0)
#define SGMII_REG_STATUS_AUTONEG BIT(2)
@@ -147,40 +178,46 @@
#define SGMII_LINK_MAC_FIBER 3
#define SGMII_LINK_MAC_PHY_FORCED 4
-#define TARGET_SGMII_BASE KS2_PASS_BASE + 0x00090100
-#define TARGET_SGMII_BASE_ADDRESSES {KS2_PASS_BASE + 0x00090100, \
- KS2_PASS_BASE + 0x00090200, \
- KS2_PASS_BASE + 0x00090400, \
- KS2_PASS_BASE + 0x00090500}
-
+#ifdef KS2_NETCP_V1_0
#define SGMII_OFFSET(x) ((x <= 1) ? (x * 0x100) : ((x * 0x100) + 0x100))
-
-/*
- * SGMII registers
- */
-#define SGMII_IDVER_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x000)
-#define SGMII_SRESET_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x004)
-#define SGMII_CTL_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x010)
-#define SGMII_STATUS_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x014)
-#define SGMII_MRADV_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x018)
-#define SGMII_LPADV_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x020)
-#define SGMII_TXCFG_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x030)
-#define SGMII_RXCFG_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x034)
-#define SGMII_AUXCFG_REG(x) (TARGET_SGMII_BASE + SGMII_OFFSET(x) + 0x038)
-
-#define DEVICE_EMACSL_BASE(x) (KS2_PASS_BASE + 0x00090900 + (x) * 0x040)
-#define DEVICE_N_GMACSL_PORTS 4
-#define DEVICE_EMACSL_RESET_POLL_COUNT 100
-
-#define DEVICE_PSTREAM_CFG_REG_ADDR (KS2_PASS_BASE + 0x604)
-
-#ifdef CONFIG_SOC_K2HK
-#define DEVICE_PSTREAM_CFG_REG_VAL_ROUTE_CPPI 0x06060606
+#elif defined KS2_NETCP_V1_5
+#define SGMII_OFFSET(x) ((x) * 0x100)
#endif
-#define hw_config_streaming_switch() \
- writel(DEVICE_PSTREAM_CFG_REG_VAL_ROUTE_CPPI,\
- DEVICE_PSTREAM_CFG_REG_ADDR);
+#define SGMII_IDVER_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x000)
+#define SGMII_SRESET_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x004)
+#define SGMII_CTL_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x010)
+#define SGMII_STATUS_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x014)
+#define SGMII_MRADV_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x018)
+#define SGMII_LPADV_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x020)
+#define SGMII_TXCFG_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x030)
+#define SGMII_RXCFG_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x034)
+#define SGMII_AUXCFG_REG(x) (EMAC_SGMII_BASE_ADDR + SGMII_OFFSET(x) + 0x038)
+
+/* PSS */
+#ifdef KS2_NETCP_V1_0
+
+#define DEVICE_PSTREAM_CFG_REG_ADDR (KS2_PASS_BASE + 0x604)
+#define DEVICE_PSTREAM_CFG_VAL_ROUTE_CPPI 0x06060606
+#define hw_config_streaming_switch()\
+ writel(DEVICE_PSTREAM_CFG_VAL_ROUTE_CPPI, DEVICE_PSTREAM_CFG_REG_ADDR);
+
+#elif defined KS2_NETCP_V1_5
+
+#define DEVICE_PSTREAM_CFG_REG_ADDR (KS2_PASS_BASE + 0x500)
+#define DEVICE_PSTREAM_CFG_VAL_ROUTE_CPPI 0x0
+
+#define hw_config_streaming_switch()\
+ writel(DEVICE_PSTREAM_CFG_VAL_ROUTE_CPPI,\
+ DEVICE_PSTREAM_CFG_REG_ADDR);\
+ writel(DEVICE_PSTREAM_CFG_VAL_ROUTE_CPPI,\
+ DEVICE_PSTREAM_CFG_REG_ADDR+4);\
+ writel(DEVICE_PSTREAM_CFG_VAL_ROUTE_CPPI,\
+ DEVICE_PSTREAM_CFG_REG_ADDR+8);\
+ writel(DEVICE_PSTREAM_CFG_VAL_ROUTE_CPPI,\
+ DEVICE_PSTREAM_CFG_REG_ADDR+12);
+
+#endif
/* EMAC MDIO Registers Structure */
struct mdio_regs {
@@ -202,9 +239,6 @@
dv_reg userphysel1;
};
-#define SGMII_ACCESS(port, reg) \
- *((volatile unsigned int *)(sgmiis[port] + reg))
-
struct eth_priv_t {
char int_name[32];
int rx_flow;
@@ -213,8 +247,6 @@
int sgmii_link_type;
};
-extern struct eth_priv_t eth_priv_cfg[];
-
int keystone2_emac_initialize(struct eth_priv_t *eth_priv);
void sgmii_serdes_setup_156p25mhz(void);
void sgmii_serdes_shutdown(void);
diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h
index 2db806c..6cfed3a 100644
--- a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h
+++ b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h
@@ -95,4 +95,7 @@
#define KS2_NETCP_PDMA_RX_RCV_QUEUE 4002
#define KS2_NETCP_PDMA_TX_SND_QUEUE 648
+/* NETCP version */
+#define KS2_NETCP_V1_0
+
#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/include/configs/k2hk_evm.h b/include/configs/k2hk_evm.h
index d0c5ff1..15cebb9 100644
--- a/include/configs/k2hk_evm.h
+++ b/include/configs/k2hk_evm.h
@@ -38,5 +38,6 @@
#define CONFIG_DRIVER_TI_KEYSTONE_NET
#define CONFIG_TI_KSNAV
#define CONFIG_KSNAV_PKTDMA_NETCP
+#define CONFIG_KSNET_CPSW_NUM_PORTS 5
#endif /* __CONFIG_K2HK_EVM_H */