powerpc/p1010rdb: add p1010rdb-pb support with updating p1010rdb-pa
- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.
For more details, see board/freescale/p1010rdb/README.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index 032c078..c6b9aca 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -120,7 +120,11 @@
#endif
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#if defined(CONFIG_P1010RDB_PA)
#define CONFIG_SYS_PCIE2_NAME "PCIe Slot"
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_SYS_PCIE2_NAME "mini PCIe Slot"
+#endif
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
@@ -200,25 +204,24 @@
#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
-
#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
#define CONFIG_SYS_DDR_RCW_1 0x00000000
#define CONFIG_SYS_DDR_RCW_2 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0x470C0000 /* Type = DDR3 */
-#define CONFIG_SYS_DDR_CONTROL_2 0x04401010
+#define CONFIG_SYS_DDR_CONTROL 0xc70c0008 /* Type = DDR3 */
+#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
#define CONFIG_SYS_DDR_TIMING_4 0x00000001
#define CONFIG_SYS_DDR_TIMING_5 0x03402400
-#define CONFIG_SYS_DDR_TIMING_3_800 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0_800 0x00330004
-#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6B4644
+#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000
+#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104
+#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644
#define CONFIG_SYS_DDR_TIMING_2_800 0x0FA888CF
#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
-#define CONFIG_SYS_DDR_MODE_1_800 0x40461520
-#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
+#define CONFIG_SYS_DDR_MODE_1_800 0x00441420
+#define CONFIG_SYS_DDR_MODE_2_800 0x00000000
#define CONFIG_SYS_DDR_INTERVAL_800 0x0C300100
-#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8655A608
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
/* settings for DDR3 at 667MT/s */
#define CONFIG_SYS_DDR_TIMING_3_667 0x00010000
@@ -315,6 +318,8 @@
| CSPR_MSEL_NAND \
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#if defined(CONFIG_P1010RDB_PA)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
@@ -322,13 +327,26 @@
| CSOR_NAND_PGS_512 /* Page Size = 512b */ \
| CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \
| CSOR_NAND_PB(32)) /* 32 Pages Per Block */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
+
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
+ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
+ | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
+ | CSOR_NAND_PB(128)) /*Pages Per Block = 128 */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
+#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
+#if defined(CONFIG_P1010RDB_PA)
/* NAND Flash Timing Params */
#define CONFIG_SYS_NAND_FTIM0 FTIM0_NAND_TCCST(0x01) | \
FTIM0_NAND_TWP(0x0C) | \
@@ -343,6 +361,23 @@
FTIM2_NAND_TWHRE(0x0f)
#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
+#elif defined(CONFIG_P1010RDB_PB)
+/* support MT29F16G08ABABAWP 4k-pagesize 2G-bytes NAND */
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07)| \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32)| \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+#endif
+
#define CONFIG_SYS_NAND_DDR_LAW 11
/* Set up IFC registers for boot location NOR/NAND */
@@ -475,10 +510,20 @@
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define I2C_PCA9557_ADDR1 0x18
+#define I2C_PCA9557_ADDR2 0x19
#define I2C_PCA9557_BUS_NUM 0
/* I2C EEPROM */
-#undef CONFIG_ID_EEPROM
+#if defined(CONFIG_P1010RDB_PB)
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define MAX_NUM_PORTS 9 /* for 128Bytes EEPROM */
+#endif
/* enable read and write access to EEPROM */
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_MULTI_EEPROMS
@@ -602,9 +647,14 @@
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_NAND)
#define CONFIG_ENV_IS_IN_NAND
+#if defined(CONFIG_P1010RDB_PA)
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) /* 3*16=48K for env */
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_ENV_SIZE (16 * 1024)
+#define CONFIG_ENV_RANGE (32 * CONFIG_ENV_SIZE) /* new block size 512K */
+#endif
#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
#elif defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
@@ -697,7 +747,6 @@
#define CONFIG_HAS_ETH2
#endif
-#define CONFIG_HOSTNAME P1010RDB
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
@@ -736,7 +785,31 @@
"ext2load usb 0:4 $loadaddr $bootfile;" \
"ext2load usb 0:4 $fdtaddr $fdtfile;" \
"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ CONFIG_BOOTMODE
+
+#if defined(CONFIG_P1010RDB_PA)
+#define CONFIG_BOOTMODE \
+ "boot_bank0=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
+ "mw.b ffb00011 0; mw.b ffb00009 0; reset\0" \
+ "boot_bank1=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
+ "mw.b ffb00011 0; mw.b ffb00009 1; reset\0" \
+ "boot_nand=i2c dev 0; i2c mw 18 1 f9; i2c mw 18 3 f0;" \
+ "mw.b ffb00011 0; mw.b ffb00017 1; reset\0"
+
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_BOOTMODE \
+ "boot_bank0=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
+ "i2c mw 19 1 2; i2c mw 19 3 e1; reset\0" \
+ "boot_bank1=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
+ "i2c mw 19 1 12; i2c mw 19 3 e1; reset\0" \
+ "boot_nand=i2c dev 0; i2c mw 18 1 fc; i2c mw 18 3 0;" \
+ "i2c mw 19 1 8; i2c mw 19 3 f7; reset\0" \
+ "boot_spi=i2c dev 0; i2c mw 18 1 fa; i2c mw 18 3 0;" \
+ "i2c mw 19 1 0; i2c mw 19 3 f7; reset\0" \
+ "boot_sd=i2c dev 0; i2c mw 18 1 f8; i2c mw 18 3 0;" \
+ "i2c mw 19 1 4; i2c mw 19 3 f3; reset\0"
+#endif
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \