ARM: tegra: enable USB device mode and UMS on some boards
For each of Jetson TK1, Venice2, and Beaver:
- Enable the first USB controller in DT, and describe its configuration.
- Enable USB device/gadget support. This allows the user to type e.g.
"ums 0 mmc 0" at the command-line to cause U-Boot to act a USB device
implementing the USB Mass Storage protocol, and expose MMC device 0
that way.
This allows a host PC to mount the Tegra device's MMC, partition it, and
install a filesystem on it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
diff --git a/arch/arm/dts/tegra124-jetson-tk1.dts b/arch/arm/dts/tegra124-jetson-tk1.dts
index 52e8c0e..464287e 100644
--- a/arch/arm/dts/tegra124-jetson-tk1.dts
+++ b/arch/arm/dts/tegra124-jetson-tk1.dts
@@ -17,7 +17,8 @@
sdhci1 = "/sdhci@700b0400";
spi0 = "/spi@7000d400";
spi1 = "/spi@7000da00";
- usb0 = "/usb@7d008000";
+ usb0 = "/usb@7d000000";
+ usb1 = "/usb@7d008000";
};
memory {
@@ -77,6 +78,12 @@
bus-width = <8>;
};
+ usb@7d000000 {
+ status = "okay";
+ dr_mode = "otg";
+ nvidia,vbus-gpio = <&gpio 108 0>; /* gpio PN4, USB_VBUS_EN0 */
+ };
+
usb@7d008000 {
status = "okay";
nvidia,vbus-gpio = <&gpio 109 0>; /* gpio PN5, USB_VBUS_EN1 */
diff --git a/arch/arm/dts/tegra124-venice2.dts b/arch/arm/dts/tegra124-venice2.dts
index 2f8d1dc..f003413 100644
--- a/arch/arm/dts/tegra124-venice2.dts
+++ b/arch/arm/dts/tegra124-venice2.dts
@@ -17,7 +17,8 @@
sdhci1 = "/sdhci@700b0400";
spi0 = "/spi@7000d400";
spi1 = "/spi@7000da00";
- usb0 = "/usb@7d008000";
+ usb0 = "/usb@7d000000";
+ usb1 = "/usb@7d008000";
};
memory {
@@ -77,6 +78,12 @@
bus-width = <8>;
};
+ usb@7d000000 {
+ status = "okay";
+ dr_mode = "otg";
+ nvidia,vbus-gpio = <&gpio 108 0>; /* gpio PN4, USB_VBUS_EN0 */
+ };
+
usb@7d008000 {
status = "okay";
nvidia,vbus-gpio = <&gpio 109 0>; /* gpio PN5, USB_VBUS_EN1 */
diff --git a/arch/arm/dts/tegra30-beaver.dts b/arch/arm/dts/tegra30-beaver.dts
index a7cc93e..85e62e9 100644
--- a/arch/arm/dts/tegra30-beaver.dts
+++ b/arch/arm/dts/tegra30-beaver.dts
@@ -14,7 +14,8 @@
i2c4 = "/i2c@7000c700";
sdhci0 = "/sdhci@78000600";
sdhci1 = "/sdhci@78000000";
- usb0 = "/usb@7d008000";
+ usb0 = "/usb@7d000000";
+ usb1 = "/usb@7d008000";
};
memory {
@@ -70,6 +71,12 @@
bus-width = <8>;
};
+ usb@7d000000 {
+ status = "okay";
+ dr_mode = "otg";
+ nvidia,vbus-gpio = <&gpio 238 0>; /* gpio DD6, PEX_L1_CLKREQ */
+ };
+
usb@7d008000 {
nvidia,vbus-gpio = <&gpio 236 0>; /* PDD4 */
status = "okay";