mmc: compile out erase and write mmc commands if write operations are not enabled
Also remove erase_grp_size and write_bl_len from struct mmc as they are
not used anymore. On ARM, removing them saves about 100 bytes of code
space in SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
index fd94987..3930aad 100644
--- a/drivers/mmc/mmc.c
+++ b/drivers/mmc/mmc.c
@@ -2066,9 +2066,11 @@
}
if (ext_csd[EXT_CSD_ERASE_GROUP_DEF] & 0x01) {
+#if CONFIG_IS_ENABLED(MMC_WRITE)
/* Read out group size from ext_csd */
mmc->erase_grp_size =
ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE] * 1024;
+#endif
/*
* if high capacity and partition setting completed
* SEC_COUNT is valid even if it is smaller than 2 GiB
@@ -2082,7 +2084,9 @@
capacity *= MMC_MAX_BLOCK_LEN;
mmc->capacity_user = capacity;
}
- } else {
+ }
+#if CONFIG_IS_ENABLED(MMC_WRITE)
+ else {
/* Calculate the group size from the csd value. */
int erase_gsz, erase_gmul;
@@ -2091,7 +2095,7 @@
mmc->erase_grp_size = (erase_gsz + 1)
* (erase_gmul + 1);
}
-
+#endif
mmc->hc_wp_grp_size = 1024
* ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE]
* ext_csd[EXT_CSD_HC_WP_GRP_SIZE];
@@ -2222,11 +2226,13 @@
mmc->dsr_imp = ((cmd.response[1] >> 12) & 0x1);
mmc->read_bl_len = 1 << ((cmd.response[1] >> 16) & 0xf);
+#if CONFIG_IS_ENABLED(MMC_WRITE)
if (IS_SD(mmc))
mmc->write_bl_len = mmc->read_bl_len;
else
mmc->write_bl_len = 1 << ((cmd.response[3] >> 22) & 0xf);
+#endif
if (mmc->high_capacity) {
csize = (mmc->csd[1] & 0x3f) << 16
@@ -2248,8 +2254,10 @@
if (mmc->read_bl_len > MMC_MAX_BLOCK_LEN)
mmc->read_bl_len = MMC_MAX_BLOCK_LEN;
+#if CONFIG_IS_ENABLED(MMC_WRITE)
if (mmc->write_bl_len > MMC_MAX_BLOCK_LEN)
mmc->write_bl_len = MMC_MAX_BLOCK_LEN;
+#endif
if ((mmc->dsr_imp) && (0xffffffff != mmc->dsr)) {
cmd.cmdidx = MMC_CMD_SET_DSR;
@@ -2273,7 +2281,9 @@
/*
* For SD, its erase group is always one sector
*/
+#if CONFIG_IS_ENABLED(MMC_WRITE)
mmc->erase_grp_size = 1;
+#endif
mmc->part_config = MMCPART_NOAVAILABLE;
err = mmc_startup_v4(mmc);
@@ -2304,7 +2314,9 @@
/* Fix the block length for DDR mode */
if (mmc->ddr_mode) {
mmc->read_bl_len = MMC_MAX_BLOCK_LEN;
+#if CONFIG_IS_ENABLED(MMC_WRITE)
mmc->write_bl_len = MMC_MAX_BLOCK_LEN;
+#endif
}
/* fill in device description */