ARM: dts: dra72: add rev C evm support
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/dts/dra72-evm-common.dtsi b/arch/arm/dts/dra72-evm-common.dtsi
new file mode 100644
index 0000000..b0993e5
--- /dev/null
+++ b/arch/arm/dts/dra72-evm-common.dtsi
@@ -0,0 +1,513 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra72x.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
+
+ chosen {
+ stdout-path = &uart1;
+ tick-timer = &timer2;
+ };
+
+ aliases {
+ display0 = &hdmi0;
+ };
+
+ evm_3v3: fixedregulator-evm_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "evm_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ extcon_usb1: extcon_usb1 {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ extcon_usb2: extcon_usb2 {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ hdmi0: connector {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
+ };
+
+ tpd12s015: encoder {
+ compatible = "ti,tpd12s015";
+
+ gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */
+ <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */
+ <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+};
+
+&dra7_pmx_core {
+ mmc1_pins_default: mmc1_pins_default {
+ pinctrl-single,pins = <
+ 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+ 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+ 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+ 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+ 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+ 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+ >;
+ };
+
+ mmc2_pins_default: mmc2_pins_default {
+ pinctrl-single,pins = <
+ 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+ 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+ 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+ 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+ 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+ 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+ 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+ 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+ 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+ 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+ >;
+ };
+
+ dcan1_pins_default: dcan1_pins_default {
+ pinctrl-single,pins = <
+ 0x3d0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+ 0x418 (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
+ >;
+ };
+
+ dcan1_pins_sleep: dcan1_pins_sleep {
+ pinctrl-single,pins = <
+ 0x3d0 (MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
+ 0x418 (MUX_MODE15 | PULL_UP) /* wakeup0.off */
+ >;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps65917: tps65917@58 {
+ compatible = "ti,tps65917";
+ reg = <0x58>;
+
+ interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ ti,system-power-controller;
+
+ tps65917_pmic {
+ compatible = "ti,tps65917-pmic";
+
+ tps65917_regulators: regulators {
+ smps1_reg: smps1 {
+ /* VDD_MPU */
+ regulator-name = "smps1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps2_reg: smps2 {
+ /* VDD_CORE */
+ regulator-name = "smps2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1060000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ smps3_reg: smps3 {
+ /* VDD_GPU IVA DSPEVE */
+ regulator-name = "smps3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ smps4_reg: smps4 {
+ /* VDDS1V8 */
+ regulator-name = "smps4";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps5_reg: smps5 {
+ /* VDD_DDR */
+ regulator-name = "smps5";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: ldo1 {
+ /* LDO1_OUT --> SDIO */
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-allow-bypass;
+ };
+
+ ldo3_reg: ldo3 {
+ /* VDDA_1V8_PHY */
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo5_reg: ldo5 {
+ /* VDDA_1V8_PLL */
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: ldo4 {
+ /* VDDA_3V_USB: VDDA_USBHS33 */
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ tps65917_power_button {
+ compatible = "ti,palmas-pwrbutton";
+ interrupt-parent = <&tps65917>;
+ interrupts = <1 IRQ_TYPE_NONE>;
+ wakeup-source;
+ ti,palmas-long-press-seconds = <6>;
+ };
+ };
+
+ pcf_gpio_21: gpio@21 {
+ compatible = "ti,pcf8575";
+ u-boot,i2c-offset-len = <0>;
+ reg = <0x21>;
+ lines-initial-states = <0x1408>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&i2c5 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ pcf_hdmi: pcf8575@26 {
+ compatible = "nxp,pcf8575";
+ u-boot,i2c-offset-len = <0>;
+ reg = <0x26>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * initial state is used here to keep the mdio interface
+ * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
+ * VIN2_S0 driven high otherwise Ethernet stops working
+ * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
+ */
+ lines-initial-states = <0x0f2b>;
+
+ p1 {
+ /* vin6_sel_s0: high: VIN6, low: audio */
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "vin6_sel_s0";
+ };
+ };
+};
+
+&uart1 {
+ status = "okay";
+ interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+ <&dra7_pmx_core 0x3e0>;
+};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ /*
+ * For the existing IOdelay configuration via U-Boot we don't
+ * support NAND on dra72-evm. Keep it disabled. Enabling it
+ * requires a different configuration by U-Boot.
+ */
+ status = "disabled";
+ ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
+ nand@0,0 {
+ /* To use NAND, DIP switch SW5 must be set like so:
+ * SW5.1 (NAND_SELn) = ON (LOW)
+ * SW5.9 (GPMC_WPN) = OFF (HIGH)
+ */
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>; /* device IO registers */
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */ /* device IO registers */
+ ti,nand-ecc-opt = "bch8";
+ ti,elm-id = <&elm>;
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <80>;
+ gpmc,cs-wr-off-ns = <80>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <60>;
+ gpmc,adv-wr-off-ns = <60>;
+ gpmc,we-on-ns = <10>;
+ gpmc,we-off-ns = <50>;
+ gpmc,oe-on-ns = <4>;
+ gpmc,oe-off-ns = <40>;
+ gpmc,access-ns = <40>;
+ gpmc,wr-access-ns = <80>;
+ gpmc,rd-cycle-ns = <80>;
+ gpmc,wr-cycle-ns = <80>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ /* MTD partition table */
+ /* All SPL-* partitions are sized to minimal length
+ * which can be independently programmable. For
+ * NAND flash this is equal to size of erase-block */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "NAND.SPL";
+ reg = <0x00000000 0x000020000>;
+ };
+ partition@1 {
+ label = "NAND.SPL.backup1";
+ reg = <0x00020000 0x00020000>;
+ };
+ partition@2 {
+ label = "NAND.SPL.backup2";
+ reg = <0x00040000 0x00020000>;
+ };
+ partition@3 {
+ label = "NAND.SPL.backup3";
+ reg = <0x00060000 0x00020000>;
+ };
+ partition@4 {
+ label = "NAND.u-boot-spl-os";
+ reg = <0x00080000 0x00040000>;
+ };
+ partition@5 {
+ label = "NAND.u-boot";
+ reg = <0x000c0000 0x00100000>;
+ };
+ partition@6 {
+ label = "NAND.u-boot-env";
+ reg = <0x001c0000 0x00020000>;
+ };
+ partition@7 {
+ label = "NAND.u-boot-env.backup1";
+ reg = <0x001e0000 0x00020000>;
+ };
+ partition@8 {
+ label = "NAND.kernel";
+ reg = <0x00200000 0x00800000>;
+ };
+ partition@9 {
+ label = "NAND.file-system";
+ reg = <0x00a00000 0x0f600000>;
+ };
+ };
+};
+
+&usb2_phy1 {
+ phy-supply = <&ldo4_reg>;
+};
+
+&usb2_phy2 {
+ phy-supply = <&ldo4_reg>;
+};
+
+&omap_dwc3_1 {
+ extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+ extcon = <&extcon_usb2>;
+};
+
+&usb1 {
+ dr_mode = "otg";
+};
+
+&usb2 {
+ dr_mode = "host";
+};
+
+&mmc1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_default>;
+ vmmc_aux-supply = <&ldo1_reg>;
+ bus-width = <4>;
+ /*
+ * SDCD signal is not being used here - using the fact that GPIO mode
+ * is a viable alternative
+ */
+ cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
+ max-frequency = <192000000>;
+};
+
+&mmc2 {
+ /* SW5-3 in ON position */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_default>;
+
+ vmmc-supply = <&evm_3v3>;
+ bus-width = <8>;
+ ti,non-removable;
+ max-frequency = <192000000>;
+};
+
+&mac {
+ status = "okay";
+};
+
+&dcan1 {
+ status = "ok";
+};
+
+&qspi {
+ status = "okay";
+
+ spi-max-frequency = <76800000>;
+ m25p80@0 {
+ compatible = "s25fl256s1", "spi-flash";
+ spi-max-frequency = <64000000>;
+ reg = <0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* MTD partition table.
+ * The ROM checks the first four physical blocks
+ * for a valid file to boot and the flash here is
+ * 64KiB block size.
+ */
+ partition@0 {
+ label = "QSPI.SPL";
+ reg = <0x00000000 0x000010000>;
+ };
+ partition@1 {
+ label = "QSPI.SPL.backup1";
+ reg = <0x00010000 0x00010000>;
+ };
+ partition@2 {
+ label = "QSPI.SPL.backup2";
+ reg = <0x00020000 0x00010000>;
+ };
+ partition@3 {
+ label = "QSPI.SPL.backup3";
+ reg = <0x00030000 0x00010000>;
+ };
+ partition@4 {
+ label = "QSPI.u-boot";
+ reg = <0x00040000 0x00100000>;
+ };
+ partition@5 {
+ label = "QSPI.u-boot-spl-os";
+ reg = <0x00140000 0x00080000>;
+ };
+ partition@6 {
+ label = "QSPI.u-boot-env";
+ reg = <0x001c0000 0x00010000>;
+ };
+ partition@7 {
+ label = "QSPI.u-boot-env.backup1";
+ reg = <0x001d0000 0x0010000>;
+ };
+ partition@8 {
+ label = "QSPI.kernel";
+ reg = <0x001e0000 0x0800000>;
+ };
+ partition@9 {
+ label = "QSPI.file-system";
+ reg = <0x009e0000 0x01620000>;
+ };
+ };
+};
+
+&dss {
+ status = "ok";
+
+ vdda_video-supply = <&ldo5_reg>;
+};
+
+&hdmi {
+ status = "ok";
+
+ port {
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+ };
+};