ARM: dts: dra72: add rev C evm support
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/dts/dra72-evm.dts b/arch/arm/dts/dra72-evm.dts
index e7c5db2..f81f918 100644
--- a/arch/arm/dts/dra72-evm.dts
+++ b/arch/arm/dts/dra72-evm.dts
@@ -5,674 +5,24 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-/dts-v1/;
-
-#include "dra72x.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include <dra72-evm-common.dtsi>
/ {
model = "TI DRA722";
compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
- chosen {
- stdout-path = &uart1;
- tick-timer = &timer2;
- };
-
memory {
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1024 MB */
};
-
- aliases {
- display0 = &hdmi0;
- };
-
- evm_3v3: fixedregulator-evm_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "evm_3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- evm_3v3_sd: fixedregulator-sd {
- compatible = "regulator-fixed";
- regulator-name = "evm_3v3_sd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- enable-active-high;
- gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
- };
-
- extcon_usb1: extcon_usb1 {
- compatible = "linux,extcon-usb-gpio";
- id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
- };
-
- extcon_usb2: extcon_usb2 {
- compatible = "linux,extcon-usb-gpio";
- id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
- };
-
- hdmi0: connector {
- compatible = "hdmi-connector";
- label = "hdmi";
-
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&tpd12s015_out>;
- };
- };
- };
-
- tpd12s015: encoder {
- compatible = "ti,tpd12s015";
-
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
- gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */
- <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */
- <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tpd12s015_in: endpoint {
- remote-endpoint = <&hdmi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tpd12s015_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
- };
};
-&dra7_pmx_core {
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
- 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
- >;
- };
-
- i2c5_pins: pinmux_i2c5_pins {
- pinctrl-single,pins = <
- 0x2b4 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */
- 0x2b8 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */
- >;
- };
-
- nand_default: nand_default {
- pinctrl-single,pins = <
- 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */
- 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */
- 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */
- 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */
- 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */
- 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */
- 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */
- 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */
- 0x20 (PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */
- 0x24 (PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */
- 0x28 (PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */
- 0x2c (PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */
- 0x30 (PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */
- 0x34 (PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */
- 0x38 (PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */
- 0x3c (PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */
- 0xb4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */
- 0xc4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */
- 0xcc (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */
- 0xc8 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */
- 0xd0 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */
- 0xd8 (PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- 0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- usb2_pins: pinmux_usb2_pins {
- pinctrl-single,pins = <
- 0x284 (PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
- >;
- };
-
- tps65917_pins_default: tps65917_pins_default {
- pinctrl-single,pins = <
- 0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
- >;
- };
-
- mmc1_pins_default: mmc1_pins_default {
- pinctrl-single,pins = <
- 0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
- 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
- 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
- 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
- 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
- 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
- 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
- >;
- };
-
- mmc2_pins_default: mmc2_pins_default {
- pinctrl-single,pins = <
- 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
- 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
- 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
- 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
- 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
- 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
- 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
- 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
- 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
- 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
- >;
- };
-
- dcan1_pins_default: dcan1_pins_default {
- pinctrl-single,pins = <
- 0x3d0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
- 0x418 (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
- >;
- };
-
- dcan1_pins_sleep: dcan1_pins_sleep {
- pinctrl-single,pins = <
- 0x3d0 (MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
- 0x418 (MUX_MODE15 | PULL_UP) /* wakeup0.off */
- >;
- };
-
- qspi1_pins: pinmux_qspi1_pins {
- pinctrl-single,pins = <
- 0x74 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */
- 0x78 (PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */
- 0x7c (PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */
- 0x80 (PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */
- 0x84 (PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */
- 0x88 (PIN_OUTPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */
- 0xb8 (PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */
- >;
- };
-
- hdmi_pins: pinmux_hdmi_pins {
- pinctrl-single,pins = <
- 0x408 (PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
- 0x40c (PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- 0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
- >;
- };
-};
-
-&i2c1 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- clock-frequency = <400000>;
-
- tps65917: tps65917@58 {
- compatible = "ti,tps65917";
- reg = <0x58>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&tps65917_pins_default>;
-
- interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
- interrupt-controller;
- #interrupt-cells = <2>;
-
- ti,system-power-controller;
-
- tps65917_pmic {
- compatible = "ti,tps65917-pmic";
-
- regulators {
- smps1_reg: smps1 {
- /* VDD_MPU */
- regulator-name = "smps1";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps2_reg: smps2 {
- /* VDD_CORE */
- regulator-name = "smps2";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1060000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- smps3_reg: smps3 {
- /* VDD_GPU IVA DSPEVE */
- regulator-name = "smps3";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- smps4_reg: smps4 {
- /* VDDS1V8 */
- regulator-name = "smps4";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps5_reg: smps5 {
- /* VDD_DDR */
- regulator-name = "smps5";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo1_reg: ldo1 {
- /* LDO1_OUT --> SDIO */
- regulator-name = "ldo1";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
-
- ldo2_reg: ldo2 {
- /* LDO2_OUT --> TP1017 (UNUSED) */
- regulator-name = "ldo2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo3_reg: ldo3 {
- /* VDDA_1V8_PHY */
- regulator-name = "ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo5_reg: ldo5 {
- /* VDDA_1V8_PLL */
- regulator-name = "ldo5";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo4_reg: ldo4 {
- /* VDDA_3V_USB: VDDA_USBHS33 */
- regulator-name = "ldo4";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
- };
- };
-
- tps65917_power_button {
- compatible = "ti,palmas-pwrbutton";
- interrupt-parent = <&tps65917>;
- interrupts = <1 IRQ_TYPE_NONE>;
- wakeup-source;
- ti,palmas-long-press-seconds = <6>;
- };
- };
-
- pcf_gpio_21: gpio@21 {
- compatible = "ti,pcf8575";
- reg = <0x21>;
- lines-initial-states = <0x1408>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-parent = <&gpio6>;
- interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- u-boot,i2c-offset-len = <0>;
- };
-};
-
-&i2c5 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins>;
- clock-frequency = <400000>;
-
- pcf_hdmi: pcf8575@26 {
- compatible = "nxp,pcf8575";
- reg = <0x26>;
- gpio-controller;
- #gpio-cells = <2>;
- /*
- * initial state is used here to keep the mdio interface
- * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
- * VIN2_S0 driven high otherwise Ethernet stops working
- * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
- */
- lines-initial-states = <0x0f2b>;
- u-boot,i2c-offset-len = <0>;
- };
-};
-
-&uart1 {
- status = "okay";
-};
-
-&elm {
- status = "okay";
-};
-
-&gpmc {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nand_default>;
- ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */
- nand@0,0 {
- /* To use NAND, DIP switch SW5 must be set like so:
- * SW5.1 (NAND_SELn) = ON (LOW)
- * SW5.9 (GPMC_WPN) = OFF (HIGH)
- */
- reg = <0 0 4>; /* device IO registers */
- ti,nand-ecc-opt = "bch8";
- ti,elm-id = <&elm>;
- nand-bus-width = <16>;
- gpmc,device-width = <2>;
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <80>;
- gpmc,cs-wr-off-ns = <80>;
- gpmc,adv-on-ns = <0>;
- gpmc,adv-rd-off-ns = <60>;
- gpmc,adv-wr-off-ns = <60>;
- gpmc,we-on-ns = <10>;
- gpmc,we-off-ns = <50>;
- gpmc,oe-on-ns = <4>;
- gpmc,oe-off-ns = <40>;
- gpmc,access-ns = <40>;
- gpmc,wr-access-ns = <80>;
- gpmc,rd-cycle-ns = <80>;
- gpmc,wr-cycle-ns = <80>;
- gpmc,bus-turnaround-ns = <0>;
- gpmc,cycle2cycle-delay-ns = <0>;
- gpmc,clk-activation-ns = <0>;
- gpmc,wait-monitoring-ns = <0>;
- gpmc,wr-data-mux-bus-ns = <0>;
- /* MTD partition table */
- /* All SPL-* partitions are sized to minimal length
- * which can be independently programmable. For
- * NAND flash this is equal to size of erase-block */
- #address-cells = <1>;
- #size-cells = <1>;
- partition@0 {
- label = "NAND.SPL";
- reg = <0x00000000 0x000020000>;
- };
- partition@1 {
- label = "NAND.SPL.backup1";
- reg = <0x00020000 0x00020000>;
- };
- partition@2 {
- label = "NAND.SPL.backup2";
- reg = <0x00040000 0x00020000>;
- };
- partition@3 {
- label = "NAND.SPL.backup3";
- reg = <0x00060000 0x00020000>;
- };
- partition@4 {
- label = "NAND.u-boot-spl-os";
- reg = <0x00080000 0x00040000>;
- };
- partition@5 {
- label = "NAND.u-boot";
- reg = <0x000c0000 0x00100000>;
- };
- partition@6 {
- label = "NAND.u-boot-env";
- reg = <0x001c0000 0x00020000>;
- };
- partition@7 {
- label = "NAND.u-boot-env.backup1";
- reg = <0x001e0000 0x00020000>;
- };
- partition@8 {
- label = "NAND.kernel";
- reg = <0x00200000 0x00800000>;
- };
- partition@9 {
- label = "NAND.file-system";
- reg = <0x00a00000 0x0f600000>;
- };
- };
-};
-
-&usb2_phy1 {
- phy-supply = <&ldo4_reg>;
-};
-
-&usb2_phy2 {
- phy-supply = <&ldo4_reg>;
-};
-
-&omap_dwc3_1 {
- extcon = <&extcon_usb1>;
-};
-
-&omap_dwc3_2 {
- extcon = <&extcon_usb2>;
-};
-
-&usb1 {
- dr_mode = "peripheral";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
-};
-
-&usb2 {
- dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_pins>;
-};
-
-&mmc1 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_default>;
-
- vmmc_aux-supply = <&ldo1_reg>;
- vmmc-supply = <&evm_3v3_sd>;
- bus-width = <4>;
- /*
- * SDCD signal is not being used here - using the fact that GPIO mode
- * is a viable alternative
- */
- cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
-};
-
-&mmc2 {
- /* SW5-3 in ON position */
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
-
- vmmc-supply = <&evm_3v3>;
- bus-width = <8>;
- ti,non-removable;
-};
-
-&dra7_pmx_core {
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 2 */
- 0x198 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */
- 0x19c (PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */
- 0x1a0 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */
- 0x1a4 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */
- 0x1a8 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */
- 0x1ac (PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */
- 0x1b0 (PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */
- 0x1b4 (PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */
- 0x1b8 (PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */
- 0x1bc (PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */
- 0x1c0 (PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */
- 0x1c4 (PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
- >;
-
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 2 */
- 0x198 (MUX_MODE15)
- 0x19c (MUX_MODE15)
- 0x1a0 (MUX_MODE15)
- 0x1a4 (MUX_MODE15)
- 0x1a8 (MUX_MODE15)
- 0x1ac (MUX_MODE15)
- 0x1b0 (MUX_MODE15)
- 0x1b4 (MUX_MODE15)
- 0x1b8 (MUX_MODE15)
- 0x1bc (MUX_MODE15)
- 0x1c0 (MUX_MODE15)
- 0x1c4 (MUX_MODE15)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- 0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */
- 0x240 (PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- 0x23c (MUX_MODE15)
- 0x240 (MUX_MODE15)
- >;
- };
-};
-
-&mac {
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_default>;
- pinctrl-1 = <&cpsw_sleep>;
- mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
-};
&cpsw_emac0 {
phy_id = <&davinci_mdio>, <3>;
phy-mode = "rgmii";
};
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_default>;
- pinctrl-1 = <&davinci_mdio_sleep>;
-};
-
-&dcan1 {
- status = "ok";
- pinctrl-names = "default", "sleep", "active";
- pinctrl-0 = <&dcan1_pins_sleep>;
- pinctrl-1 = <&dcan1_pins_sleep>;
- pinctrl-2 = <&dcan1_pins_default>;
-};
-
-&qspi {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&qspi1_pins>;
-
- spi-max-frequency = <76800000>;
- m25p80@0 {
- compatible = "s25fl256s1","spi-flash";
- spi-max-frequency = <64000000>;
- reg = <0>;
- spi-tx-bus-width = <1>;
- spi-rx-bus-width = <4>;
- #address-cells = <1>;
- #size-cells = <1>;
-
- /* MTD partition table.
- * The ROM checks the first four physical blocks
- * for a valid file to boot and the flash here is
- * 64KiB block size.
- */
- partition@0 {
- label = "QSPI.SPL";
- reg = <0x00000000 0x000010000>;
- };
- partition@1 {
- label = "QSPI.SPL.backup1";
- reg = <0x00010000 0x00010000>;
- };
- partition@2 {
- label = "QSPI.SPL.backup2";
- reg = <0x00020000 0x00010000>;
- };
- partition@3 {
- label = "QSPI.SPL.backup3";
- reg = <0x00030000 0x00010000>;
- };
- partition@4 {
- label = "QSPI.u-boot";
- reg = <0x00040000 0x00100000>;
- };
- partition@5 {
- label = "QSPI.u-boot-spl-os";
- reg = <0x00140000 0x00080000>;
- };
- partition@6 {
- label = "QSPI.u-boot-env";
- reg = <0x001c0000 0x00010000>;
- };
- partition@7 {
- label = "QSPI.u-boot-env.backup1";
- reg = <0x001d0000 0x0010000>;
- };
- partition@8 {
- label = "QSPI.kernel";
- reg = <0x001e0000 0x0800000>;
- };
- partition@9 {
- label = "QSPI.file-system";
- reg = <0x009e0000 0x01620000>;
- };
- };
-};
-
&dss {
status = "ok";
@@ -680,15 +30,9 @@
};
&hdmi {
- status = "ok";
vdda-supply = <&ldo3_reg>;
+};
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pins>;
-
- port {
- hdmi_out: endpoint {
- remote-endpoint = <&tpd12s015_in>;
- };
- };
+&mac {
+ mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
};