armv8: ls1088ardb: Add support for LS1088ARDB platform
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
diff --git a/board/freescale/ls1088a/Kconfig b/board/freescale/ls1088a/Kconfig
new file mode 100644
index 0000000..a4d8223
--- /dev/null
+++ b/board/freescale/ls1088a/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_LS1088ARDB
+
+config SYS_BOARD
+ default "ls1088a"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls1088ardb"
+
+endif
diff --git a/board/freescale/ls1088a/MAINTAINERS b/board/freescale/ls1088a/MAINTAINERS
new file mode 100644
index 0000000..12834f6
--- /dev/null
+++ b/board/freescale/ls1088a/MAINTAINERS
@@ -0,0 +1,7 @@
+LS1088ARDB BOARD
+M: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
+M: Ashish Kumar <Ashish.Kumar@nxp.com>
+S: Maintained
+F: board/freescale/ls1088a/
+F: include/configs/ls1088ardb.h
+F: configs/ls1088ardb_qspi_defconfig
diff --git a/board/freescale/ls1088a/Makefile b/board/freescale/ls1088a/Makefile
new file mode 100644
index 0000000..e997cf1
--- /dev/null
+++ b/board/freescale/ls1088a/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += ls1088a.o
+obj-$(CONFIG_TARGET_LS1088ARDB) += eth_ls1088ardb.o
+obj-y += ddr.o
diff --git a/board/freescale/ls1088a/README b/board/freescale/ls1088a/README
new file mode 100644
index 0000000..3f4d987
--- /dev/null
+++ b/board/freescale/ls1088a/README
@@ -0,0 +1,66 @@
+Overview
+--------
+The LS1088A Reference Design (RDB) is a high-performance computing,
+evaluation, and development platform that supports ARM SoC LS1088A and its
+derivatives.
+
+
+LS1088A SoC Overview
+--------------------------------------
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
+
+RDB Default Switch Settings (1: ON; 0: OFF)
+-------------------------------------------
+
+For QSPI Boot
+SW1 0011 0001
+SW2 x100 0000
+SW3 1111 0010
+SW4 1001 0011
+SW5 1111 0000
+
+For SD Boot
+SW1 0010 0000
+SW2 0100 0000
+SW3 1111 0010
+SW4 1001 0011
+SW5 1111 0000
+
+For eMMC Boot
+SW1 0010 0000
+SW2 1100 0000
+SW3 1111 0010
+SW4 1001 0011
+SW5 1111 0000
+
+Alternately you can use this command to switch from QSPI to SD
+
+=> i2c mw 66 0x60 0x20; i2c mw 66 10 10;i2c mw 66 10 21
+
+ LS1088ARDB board Overview
+ -------------------------
+ - SERDES Connections, 16 lanes supporting:
+ - PCI Express - 3.0
+ - SATA 3.0
+ - XFI
+ - QSGMII
+ - DDR Controller
+ - One ports of 72-bits (8-bits ECC, 64-bits DATA) DDR4. Each port supports four
+ chip-selects on one DIMM connector. Support is up to 2133MT/s, Although MAX default
+ with FSL refernce software is 2100MT/s
+ - 2 QSPI-NOR Spansion(S25FS512SDSMFI011) flash of size 64MB
+ - IFC/Local Bus
+ - One 2 GB NAND flash with ECC support, not as boot source
+ - CPLD of size 2K
+ - USB 3.0
+ - Two high speed USB 3.0 ports
+ - First USB 3.0 port configured as Host with Type-A connector
+ - Second USB 3.0 port configured as OTG with micro-AB connector
+ - SDHC/eMMC
+ - SDHC slot and onboard eMMC are muxed together
+ - 4 I2C controllers
+ - Two SATA onboard connectors
+ - 2 UART
+ - JTAG support
+ - QSPI emulator support
+ - TDM riser support
diff --git a/board/freescale/ls1088a/ddr.c b/board/freescale/ls1088a/ddr.c
new file mode 100644
index 0000000..0ecfd65
--- /dev/null
+++ b/board/freescale/ls1088a/ddr.c
@@ -0,0 +1,102 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/clock.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ /*
+ * we use identical timing for all slots. If needed, change the code
+ * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+ */
+ pbsp = udimms[0];
+
+ /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found for %lu MT/s\n",
+ ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+ pbsp->wrlvl_ctl_3);
+
+
+
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* Enable DDR hashing */
+ popts->addr_hash = 1;
+
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
+ DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
+}
+
+
+int fsl_initdram(void)
+{
+ puts("Initializing DDR....using SPD\n");
+
+ gd->ram_size = fsl_ddr_sdram();
+
+ return 0;
+}
diff --git a/board/freescale/ls1088a/ddr.h b/board/freescale/ls1088a/ddr.h
new file mode 100644
index 0000000..dfcfc1f
--- /dev/null
+++ b/board/freescale/ls1088a/ddr.h
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1088A_DDR_H__
+#define __LS1088A_DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+#if defined(CONFIG_TARGET_LS1088ARDB)
+
+ {2, 1666, 0, 8, 8, 0x090A0B0E, 0x0F10110D,},
+ {2, 1900, 0, 4, 7, 0x09090B0D, 0x0E10120B,},
+ {2, 2300, 0, 8, 9, 0x0A0C0E11, 0x1214160F,},
+ {}
+
+#endif
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+#endif
diff --git a/board/freescale/ls1088a/eth_ls1088ardb.c b/board/freescale/ls1088a/eth_ls1088ardb.c
new file mode 100644
index 0000000..853d815
--- /dev/null
+++ b/board/freescale/ls1088a/eth_ls1088ardb.c
@@ -0,0 +1,102 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <malloc.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <fm_eth.h>
+#include <asm/io.h>
+#include <exports.h>
+#include <asm/arch/fsl_serdes.h>
+#include <fsl-mc/ldpaa_wriop.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define MC_BOOT_ENV_VAR "mcinitcmd"
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FSL_MC_ENET)
+ char *mc_boot_env_var;
+ int i, interface;
+ struct memac_mdio_info mdio_info;
+ struct mii_dev *dev;
+ struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+ struct memac_mdio_controller *reg;
+ u32 srds_s1, cfg;
+
+ cfg = in_le32(&gur->rcwsr[FSL_CHASSIS3_SRDS1_REGSR - 1]) &
+ FSL_CHASSIS3_SRDS1_PRTCL_MASK;
+ cfg >>= FSL_CHASSIS3_SRDS1_PRTCL_SHIFT;
+
+ srds_s1 = serdes_get_number(FSL_SRDS_1, cfg);
+
+ reg = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO1;
+ mdio_info.regs = reg;
+ mdio_info.name = DEFAULT_WRIOP_MDIO1_NAME;
+
+ /* Register the EMI 1 */
+ fm_memac_mdio_init(bis, &mdio_info);
+
+ reg = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO2;
+ mdio_info.regs = reg;
+ mdio_info.name = DEFAULT_WRIOP_MDIO2_NAME;
+
+ /* Register the EMI 2 */
+ fm_memac_mdio_init(bis, &mdio_info);
+
+ switch (srds_s1) {
+ case 0x1D:
+ /*
+ * XFI does not need a PHY to work, but to avoid U-boot use
+ * default PHY address which is zero to a MAC when it found
+ * a MAC has no PHY address, we give a PHY address to XFI
+ * MAC error.
+ */
+ wriop_set_phy_address(WRIOP1_DPMAC1, 0x0a);
+ wriop_set_phy_address(WRIOP1_DPMAC2, AQ_PHY_ADDR1);
+ wriop_set_phy_address(WRIOP1_DPMAC3, QSGMII1_PORT1_PHY_ADDR);
+ wriop_set_phy_address(WRIOP1_DPMAC4, QSGMII1_PORT2_PHY_ADDR);
+ wriop_set_phy_address(WRIOP1_DPMAC5, QSGMII1_PORT3_PHY_ADDR);
+ wriop_set_phy_address(WRIOP1_DPMAC6, QSGMII1_PORT4_PHY_ADDR);
+ wriop_set_phy_address(WRIOP1_DPMAC7, QSGMII2_PORT1_PHY_ADDR);
+ wriop_set_phy_address(WRIOP1_DPMAC8, QSGMII2_PORT2_PHY_ADDR);
+ wriop_set_phy_address(WRIOP1_DPMAC9, QSGMII2_PORT3_PHY_ADDR);
+ wriop_set_phy_address(WRIOP1_DPMAC10, QSGMII2_PORT4_PHY_ADDR);
+
+ break;
+ default:
+ printf("SerDes1 protocol 0x%x is not supported on LS1088ARDB\n",
+ srds_s1);
+ break;
+ }
+
+ for (i = WRIOP1_DPMAC3; i <= WRIOP1_DPMAC10; i++) {
+ interface = wriop_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_QSGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME);
+ wriop_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+ dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME);
+ wriop_set_mdio(WRIOP1_DPMAC2, dev);
+
+ mc_boot_env_var = env_get(MC_BOOT_ENV_VAR);
+ if (mc_boot_env_var)
+ run_command_list(mc_boot_env_var, -1, 0);
+ cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+ return pci_eth_init(bis);
+}
diff --git a/board/freescale/ls1088a/ls1088a.c b/board/freescale/ls1088a/ls1088a.c
new file mode 100644
index 0000000..a022da9
--- /dev/null
+++ b/board/freescale/ls1088a/ls1088a.c
@@ -0,0 +1,332 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <i2c.h>
+#include <malloc.h>
+#include <errno.h>
+#include <netdev.h>
+#include <fsl_ifc.h>
+#include <fsl_ddr.h>
+#include <fsl_sec.h>
+#include <asm/io.h>
+#include <fdt_support.h>
+#include <libfdt.h>
+#include <fsl-mc/fsl_mc.h>
+#include <environment.h>
+#include <asm/arch-fsl-layerscape/soc.h>
+#include <asm/arch/ppa.h>
+
+#include "../common/qixis.h"
+#include "ls1088a_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+unsigned long long get_qixis_addr(void)
+{
+ unsigned long long addr;
+
+ if (gd->flags & GD_FLG_RELOC)
+ addr = QIXIS_BASE_PHYS;
+ else
+ addr = QIXIS_BASE_PHYS_EARLY;
+
+ /*
+ * IFC address under 256MB is mapped to 0x30000000, any address above
+ * is mapped to 0x5_10000000 up to 4GB.
+ */
+ addr = addr > 0x10000000 ? addr + 0x500000000ULL : addr + 0x30000000;
+
+ return addr;
+}
+
+int checkboard(void)
+{
+ char buf[64];
+ u8 sw;
+ static const char *const freq[] = {"100", "125", "156.25",
+ "100 separate SSCG"};
+ int clock;
+
+
+ printf("Board: LS1088A-RDB, ");
+
+ sw = QIXIS_READ(arch);
+ printf("Board Arch: V%d, ", sw >> 4);
+
+ printf("Board version: %c, boot from ", (sw & 0xf) + 'A');
+
+
+ memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));
+
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+#ifdef CONFIG_SD_BOOT
+ puts("SD card\n");
+#endif
+ switch (sw) {
+ case 0:
+
+ puts("QSPI:");
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_QMAP_MASK) >> QIXIS_QMAP_SHIFT;
+ if (sw == 0 || sw == 4)
+ puts("0\n");
+ else if (sw == 1)
+ puts("1\n");
+ else
+ puts("EMU\n");
+ break;
+
+ default:
+ printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+ break;
+ }
+
+
+ printf("CPLD: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
+
+
+ /*
+ * Display the actual SERDES reference clocks as configured by the
+ * dip switches on the board. Note that the SWx registers could
+ * technically be set to force the reference clocks to match the
+ * values that the SERDES expects (or vice versa). For now, however,
+ * we just display both values and hope the user notices when they
+ * don't match.
+ */
+ puts("SERDES1 Reference : ");
+ sw = QIXIS_READ(brdcfg[2]);
+ clock = (sw >> 6) & 3;
+ printf("Clock1 = %sMHz ", freq[clock]);
+ clock = (sw >> 4) & 3;
+ printf("Clock2 = %sMHz", freq[clock]);
+
+ puts("\nSERDES2 Reference : ");
+ clock = (sw >> 2) & 3;
+ printf("Clock1 = %sMHz ", freq[clock]);
+ clock = (sw >> 0) & 3;
+ printf("Clock2 = %sMHz\n", freq[clock]);
+
+ return 0;
+}
+
+bool if_board_diff_clk(void)
+{
+ u8 diff_conf = QIXIS_READ(dutcfg[11]);
+ return diff_conf & 0x80;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch (sysclk_conf & 0x0f) {
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+ if (if_board_diff_clk())
+ return get_board_sys_clk();
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+
+ return 66666666;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+void board_retimer_init(void)
+{
+ u8 reg;
+
+ /* Retimer is connected to I2C1_CH5 */
+ select_i2c_ch_pca9547(I2C_MUX_CH5);
+
+ /* Access to Control/Shared register */
+ reg = 0x0;
+ i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
+
+ /* Read device revision and ID */
+ i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1);
+ debug("Retimer version id = 0x%x\n", reg);
+
+ /* Enable Broadcast. All writes target all channel register sets */
+ reg = 0x0c;
+ i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
+
+ /* Reset Channel Registers */
+ i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1);
+ reg |= 0x4;
+ i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1);
+
+ /* Set data rate as 10.3125 Gbps */
+ reg = 0x90;
+ i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1);
+ reg = 0xb3;
+ i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1);
+ reg = 0x90;
+ i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1);
+ reg = 0xb3;
+ i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1);
+ reg = 0xcd;
+ i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1);
+
+ /* Select VCO Divider to full rate (000) */
+ i2c_read(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
+ reg &= 0x0f;
+ reg |= 0x70;
+ i2c_write(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
+
+
+ /*return the default channel*/
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+}
+
+int board_init(void)
+{
+ init_final_memctl_regs();
+#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
+ u32 __iomem *irq_ccsr = (u32 __iomem *)ISC_BASE;
+#endif
+
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+ board_retimer_init();
+
+#ifdef CONFIG_ENV_IS_NOWHERE
+ gd->env_addr = (ulong)&default_environment[0];
+#endif
+
+#if defined(CONFIG_TARGET_LS1088ARDB) && defined(CONFIG_FSL_MC_ENET)
+ /* invert AQR105 IRQ pins polarity */
+ out_le32(irq_ccsr + IRQCR_OFFSET / 4, AQR105_IRQ_MASK);
+#endif
+
+#ifdef CONFIG_FSL_LS_PPA
+ ppa_init();
+#endif
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ fsl_lsch3_early_init_f();
+ return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+ puts("\nDDR ");
+ print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
+ print_ddr_info(0);
+}
+
+#if defined(CONFIG_ARCH_MISC_INIT)
+int arch_misc_init(void)
+{
+#ifdef CONFIG_FSL_CAAM
+ sec_init();
+#endif
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+void fdt_fixup_board_enet(void *fdt)
+{
+ int offset;
+
+ offset = fdt_path_offset(fdt, "/fsl-mc");
+
+ if (offset < 0)
+ offset = fdt_path_offset(fdt, "/fsl,dprc@0");
+
+ if (offset < 0) {
+ printf("%s: ERROR: fsl-mc node not found in device tree (error %d)\n",
+ __func__, offset);
+ return;
+ }
+
+ if (get_mc_boot_status() == 0)
+ fdt_status_okay(fdt, offset);
+ else
+ fdt_status_fail(fdt, offset);
+}
+#endif
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ int err, i;
+ u64 base[CONFIG_NR_DRAM_BANKS];
+ u64 size[CONFIG_NR_DRAM_BANKS];
+
+ ft_cpu_setup(blob, bd);
+
+ /* fixup DT for the two GPP DDR banks */
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ base[i] = gd->bd->bi_dram[i].start;
+ size[i] = gd->bd->bi_dram[i].size;
+ }
+
+#ifdef CONFIG_RESV_RAM
+ /* reduce size if reserved memory is within this bank */
+ if (gd->arch.resv_ram >= base[0] &&
+ gd->arch.resv_ram < base[0] + size[0])
+ size[0] = gd->arch.resv_ram - base[0];
+ else if (gd->arch.resv_ram >= base[1] &&
+ gd->arch.resv_ram < base[1] + size[1])
+ size[1] = gd->arch.resv_ram - base[1];
+#endif
+
+ fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);
+
+#ifdef CONFIG_FSL_MC_ENET
+ fdt_fixup_board_enet(blob);
+ err = fsl_mc_ldpaa_exit(bd);
+ if (err)
+ return err;
+#endif
+
+ return 0;
+}
+#endif
diff --git a/board/freescale/ls1088a/ls1088a_qixis.h b/board/freescale/ls1088a/ls1088a_qixis.h
new file mode 100644
index 0000000..9757d1b
--- /dev/null
+++ b/board/freescale/ls1088a/ls1088a_qixis.h
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1088AQDS_QIXIS_H__
+#define __LS1088AQDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for LS1088AQDS */
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_66 0x0
+#define QIXIS_SYSCLK_83 0x1
+#define QIXIS_SYSCLK_100 0x2
+#define QIXIS_SYSCLK_125 0x3
+#define QIXIS_SYSCLK_133 0x4
+#define QIXIS_SYSCLK_150 0x5
+#define QIXIS_SYSCLK_160 0x6
+#define QIXIS_SYSCLK_166 0x7
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_66 0x0
+#define QIXIS_DDRCLK_100 0x1
+#define QIXIS_DDRCLK_125 0x2
+#define QIXIS_DDRCLK_133 0x3
+
+/* BRDCFG2 - SD clock*/
+#define QIXIS_SDCLK1_100 0x0
+#define QIXIS_SDCLK1_125 0x1
+#define QIXIS_SDCLK1_165 0x2
+#define QIXIS_SDCLK1_100_SP 0x3
+
+#endif