mpc83xx: add ids8313 support
add support for the ids8313 board.
CPU: e300c3, MPC8313, Rev: 2.1 at 396 MHz, CSB: 132 MHz
I2C: ready
SPI: ready
DRAM: 128 MiB (DDR2, 32-bit, ECC off, 264 MHz)
Flash: 8 MiB
NAND: 128 MiB
Net: TSEC0, TSEC1 [PRIME]
public key on NOR flash start
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
diff --git a/board/ids/ids8313/Makefile b/board/ids/ids8313/Makefile
new file mode 100644
index 0000000..56cfd40
--- /dev/null
+++ b/board/ids/ids8313/Makefile
@@ -0,0 +1,11 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2013
+# Heiko Schocher, DENX Software Engineering, <hs@denx.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y = ids8313.o
diff --git a/board/ids/ids8313/ids8313.c b/board/ids/ids8313/ids8313.c
new file mode 100644
index 0000000..f742143
--- /dev/null
+++ b/board/ids/ids8313/ids8313.c
@@ -0,0 +1,208 @@
+/*
+ * (C) Copyright 2013
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * Based on:
+ * Copyright (c) 2011 IDS GmbH, Germany
+ * ids8313.c - ids8313 board support.
+ *
+ * Sergej Stepanov <ste@ids.de>
+ * Based on board/freescale/mpc8313erdb/mpc8313erdb.c
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spi.h>
+#include <libfdt.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+/** CPLD contains the info about:
+ * - board type: *pCpld & 0xF0
+ * - hw-revision: *pCpld & 0x0F
+ * - cpld-revision: *pCpld+1
+ */
+int checkboard(void)
+{
+ char *pcpld = (char *)CONFIG_SYS_CPLD_BASE;
+ u8 u8Vers = readb(pcpld);
+ u8 u8Revs = readb(pcpld + 1);
+
+ printf("Board: ");
+ switch (u8Vers & 0xF0) {
+ case '\x40':
+ printf("CU73X");
+ break;
+ case '\x50':
+ printf("CC73X");
+ break;
+ default:
+ printf("unknown(0x%02X, 0x%02X)\n", u8Vers, u8Revs);
+ return 0;
+ }
+ printf("\nInfo: HW-Rev: %i, CPLD-Rev: %i\n",
+ u8Vers & 0x0F, u8Revs & 0xFF);
+ return 0;
+}
+
+/*
+ * fixed sdram init
+ */
+int fixed_sdram(unsigned long config)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ u32 msize = CONFIG_SYS_DDR_SIZE << 20;
+
+#ifndef CONFIG_SYS_RAMBOOT
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ (CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000));
+ out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+ sync();
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ udelay(50000);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], config);
+
+ /* currently we use only one CS, so disable the other banks */
+ out_be32(&im->ddr.cs_config[1], 0);
+ out_be32(&im->ddr.cs_config[2], 0);
+ out_be32(&im->ddr.cs_config[3], 0);
+
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_SDRAM_CFG);
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_SDRAM_CFG2);
+
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE_2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL);
+ sync();
+ udelay(300);
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+ /* now check the real size */
+ disable_addr_trans();
+ msize = get_ram_size(CONFIG_SYS_DDR_BASE, msize);
+ enable_addr_trans();
+#endif
+ return msize;
+}
+
+static int setup_sdram(void)
+{
+ u32 msize = CONFIG_SYS_DDR_SIZE << 20;
+ long int size_01, size_02;
+
+ size_01 = fixed_sdram(CONFIG_SYS_DDR_CONFIG);
+ size_02 = fixed_sdram(CONFIG_SYS_DDR_CONFIG_256);
+
+ if (size_01 > size_02)
+ msize = fixed_sdram(CONFIG_SYS_DDR_CONFIG);
+ else
+ msize = size_02;
+
+ return msize;
+}
+
+phys_size_t initdram(int board_type)
+{
+ immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ fsl_lbc_t *lbc = &im->im_lbc;
+ u32 msize = 0;
+
+ if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ msize = setup_sdram();
+
+ out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+ out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
+ sync();
+
+ return msize;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+}
+#endif
+
+/* gpio mask for spi_cs */
+#define IDSCPLD_SPI_CS_MASK 0x00000001
+/* spi_cs multiplexed through cpld */
+#define IDSCPLD_SPI_CS_BASE (CONFIG_SYS_CPLD_BASE + 0xf)
+
+#if defined(CONFIG_MISC_INIT_R)
+/* srp umcr mask for rts */
+#define IDSUMCR_RTS_MASK 0x04
+int misc_init_r(void)
+{
+ /*srp*/
+ duart83xx_t *uart1 = &((immap_t *)CONFIG_SYS_IMMR)->duart[0];
+ duart83xx_t *uart2 = &((immap_t *)CONFIG_SYS_IMMR)->duart[1];
+
+ gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
+ u8 *spi_base = (u8 *)IDSCPLD_SPI_CS_BASE;
+
+ /* deactivate spi_cs channels */
+ out_8(spi_base, 0);
+ /* deactivate the spi_cs */
+ setbits_be32(&iopd->dir, IDSCPLD_SPI_CS_MASK);
+ /*srp - deactivate rts*/
+ out_8(&uart1->umcr, IDSUMCR_RTS_MASK);
+ out_8(&uart2->umcr, IDSUMCR_RTS_MASK);
+
+
+ gd->fdt_blob = (void *)CONFIG_SYS_FLASH_BASE;
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MPC8XXX_SPI
+/*
+ * The following are used to control the SPI chip selects
+ */
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ return bus == 0 && ((cs >= 0) && (cs <= 2));
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
+ u8 *spi_base = (u8 *)IDSCPLD_SPI_CS_BASE;
+
+ /* select the spi_cs channel */
+ out_8(spi_base, 1 << slave->cs);
+ /* activate the spi_cs */
+ clrbits_be32(&iopd->dat, IDSCPLD_SPI_CS_MASK);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ gpio83xx_t *iopd = &((immap_t *)CONFIG_SYS_IMMR)->gpio[0];
+ u8 *spi_base = (u8 *)IDSCPLD_SPI_CS_BASE;
+
+ /* select the spi_cs channel */
+ out_8(spi_base, 1 << slave->cs);
+ /* deactivate the spi_cs */
+ setbits_be32(&iopd->dat, IDSCPLD_SPI_CS_MASK);
+}
+#endif /* CONFIG_HARD_SPI */
diff --git a/boards.cfg b/boards.cfg
index c8270b2..83fc3af 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -719,6 +719,7 @@
Active powerpc mpc83xx - freescale mpc837xemds MPC837XEMDS - Dave Liu <daveliu@freescale.com>
Active powerpc mpc83xx - freescale mpc837xemds MPC837XEMDS_HOST MPC837XEMDS:PCI Dave Liu <daveliu@freescale.com>
Active powerpc mpc83xx - freescale mpc837xerdb MPC837XERDB - Joe D'Abbraccio <ljd015@freescale.com>
+Active powerpc mpc83xx - ids ids8313 ids8313 ids8313:SYS_TEXT_BASE=0xFFF00000 Heiko Schocher <hs@denx.de>
Active powerpc mpc83xx - keymile km83xx kmcoge5ne km8360:KMCOGE5NE Holger Brunck <holger.brunck@keymile.com>
Active powerpc mpc83xx - keymile km83xx kmeter1 km8360:KMETER1 Holger Brunck <holger.brunck@keymile.com>
Active powerpc mpc83xx - keymile km83xx kmopti2 tuxx1:KMOPTI2 Holger Brunck <holger.brunck@keymile.com>
diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h
new file mode 100644
index 0000000..613f7e1
--- /dev/null
+++ b/include/configs/ids8313.h
@@ -0,0 +1,587 @@
+/*
+ * (C) Copyright 2013
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * Based on:
+ * Copyright (c) 2011 IDS GmbH, Germany
+ * Sergej Stepanov <ste@ids.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC831x
+#define CONFIG_MPC8313
+#define CONFIG_IDS8313
+
+#define CONFIG_FSL_ELBC
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT \
+ "\nEnter password - autoboot in %d seconds...\n", CONFIG_BOOTDELAY
+#define CONFIG_AUTOBOOT_DELAY_STR "ids"
+#define CONFIG_BOOT_RETRY_TIME 900
+#define CONFIG_BOOT_RETRY_MIN 30
+#define CONFIG_BOOTDELAY 1
+#define CONFIG_RESET_TO_RETRY
+
+#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR 0xF0000000
+
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.000MHz, then
+ * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
+ */
+#define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0XFFF00100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_8BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_MII |\
+ HRCWH_TSEC2M_IN_MII |\
+ HRCWH_BIG_ENDIAN)
+
+#define CONFIG_SYS_SICRH 0x00000000
+#define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D)
+
+#define CONFIG_HWCONFIG
+
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\
+ HID0_ENABLE_INSTRUCTION_CACHE |\
+ HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
+
+#define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000)
+
+/*
+ * Definitions for initial stack pointer and data area (in DCACHE )
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
+ - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR (0x00040000 |\
+ (0xFF << LBCR_BMT_SHIFT) |\
+ 0xF)
+
+#define CONFIG_SYS_LBC_MRTPR 0x20000000
+
+/*
+ * Internal Definitions
+ */
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+
+/*
+ * Manually set up DDR parameters,
+ * as this board has not the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE 256 /* MB */
+#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\
+ 0x00010000 |\
+ CSCONFIG_ROW_BIT_13 |\
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \
+ CSCONFIG_BANK_BIT_3)
+
+#define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */
+#define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\
+ (3 << TIMING_CFG0_WRT_SHIFT) |\
+ (3 << TIMING_CFG0_RRT_SHIFT) |\
+ (3 << TIMING_CFG0_WWT_SHIFT) |\
+ (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+#define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
+ (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
+ (4 << TIMING_CFG1_ACTTORW_SHIFT) |\
+ (7 << TIMING_CFG1_CASLAT_SHIFT) |\
+ (4 << TIMING_CFG1_REFREC_SHIFT) |\
+ (4 << TIMING_CFG1_WRREC_SHIFT) |\
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
+ (2 << TIMING_CFG1_WRTORD_SHIFT))
+#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
+ (5 << TIMING_CFG2_CPO_SHIFT) |\
+ (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
+ (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
+ (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
+ (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
+
+#define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
+ (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+
+#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\
+ SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
+ SDRAM_CFG_DBW_32 |\
+ SDRAM_CFG_SDRAM_TYPE_DDR2)
+
+#define CONFIG_SYS_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
+ (0x0242 << SDRAM_MODE_SD_SHIFT))
+#define CONFIG_SYS_DDR_MODE_2 0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
+#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\
+ DDRCDR_PZ_NOMZ |\
+ DDRCDR_NZ_NOMZ |\
+ DDRCDR_ODT |\
+ DDRCDR_M_ODR |\
+ DDRCDR_Q_DRN)
+
+/*
+ * on-board devices
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+#define CONFIG_TSEC_ENET
+#define CONFIG_NET_MULTI
+#define CONFIG_HARD_SPI
+#define CONFIG_HARD_I2C
+
+/*
+ * NOR FLASH setup
+ */
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
+#define CONFIG_FLASH_SHOW_PROGRESS 50
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_SYS_FLASH_BASE 0xFF800000
+#define CONFIG_SYS_FLASH_SIZE 8
+#define CONFIG_SYS_FLASH_PROTECTION
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016
+
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\
+ BR_PS_8 |\
+ BR_MS_GPCM |\
+ BR_V)
+
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
+ OR_GPCM_SCY_10 |\
+ OR_GPCM_EHTR |\
+ OR_GPCM_TRLX |\
+ OR_GPCM_CSNT |\
+ OR_GPCM_EAD)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 128
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500
+
+/*
+ * NAND FLASH setup
+ */
+#define CONFIG_SYS_NAND_BASE 0xE1000000
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_MAX_CHIPS 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_PAGE_SIZE (2048)
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
+#define NAND_CACHE_PAGES 64
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
+
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\
+ (2<<BR_DECC_SHIFT) |\
+ BR_PS_8 |\
+ BR_MS_FCM |\
+ BR_V)
+
+#define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\
+ OR_FCM_PGS |\
+ OR_FCM_CSCT |\
+ OR_FCM_CST |\
+ OR_FCM_CHT |\
+ OR_FCM_SCY_4 |\
+ OR_FCM_TRLX |\
+ OR_FCM_EHTR |\
+ OR_FCM_RST)
+
+/*
+ * MRAM setup
+ */
+#define CONFIG_SYS_MRAM_BASE 0xE2000000
+#define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */
+
+#define CONFIG_SYS_OR_TIMING_MRAM
+
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\
+ BR_PS_8 |\
+ BR_MS_GPCM |\
+ BR_V)
+
+#define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74
+
+/*
+ * CPLD setup
+ */
+#define CONFIG_SYS_CPLD_BASE 0xE3000000
+#define CONFIG_SYS_CPLD_SIZE 0x8000
+#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E
+
+#define CONFIG_SYS_OR_TIMING_MRAM
+
+#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\
+ BR_PS_8 |\
+ BR_MS_GPCM |\
+ BR_V)
+
+#define CONFIG_SYS_OR3_PRELIM 0xFFFF8814
+
+/*
+ * HW-Watchdog
+ */
+#define CONFIG_WATCHDOG 1
+#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
+
+/*
+ * I2C setup
+ */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 400000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100
+#define CONFIG_RTC_PCF8563
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51
+
+/*
+ * SPI setup
+ */
+#ifdef CONFIG_HARD_SPI
+#define CONFIG_MPC8XXX_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR 0x00000001
+#define CONFIG_SYS_GPIO1_DAT 0x00000001
+#endif
+
+/*
+ * Ethernet setup
+ */
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define TSEC1_PHY_ADDR 0x1
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC1_PHYIDX 0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define TSEC2_PHY_ADDR 0x3
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC2_PHYIDX 0
+#endif
+#define CONFIG_ETHPRIME "TSEC1"
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
+#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
+
+#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_SYS_SCCR_USBDRCM 3
+
+/*
+ * BAT's
+ */
+#define CONFIG_HIGH_BATS
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\
+ BATL_PP_10)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\
+ BATU_BL_256M |\
+ BATU_VS |\
+ BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+
+/* Initial RAM @ 0xFD000000 */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\
+ BATL_PP_10 |\
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\
+ BATU_BL_256K |\
+ BATU_VS |\
+ BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+
+/* FLASH @ 0xFF800000 */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\
+ BATL_PP_10 |\
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\
+ BATU_BL_8M |\
+ BATU_VS |\
+ BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\
+ BATL_PP_10 |\
+ BATL_CACHEINHIBIT |\
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+
+#define CONFIG_SYS_IBAT3L (0)
+#define CONFIG_SYS_IBAT3U (0)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+
+#define CONFIG_SYS_IBAT4L (0)
+#define CONFIG_SYS_IBAT4U (0)
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
+
+/* IMMRBAR @ 0xF0000000 */
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\
+ BATL_PP_10 |\
+ BATL_CACHEINHIBIT |\
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\
+ BATU_BL_128M |\
+ BATU_VS |\
+ BATU_VP)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+
+/* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
+#define CONFIG_SYS_IBAT6L (0xE0000000 |\
+ BATL_PP_10 |\
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U (0xE0000000 |\
+ BATU_BL_256M |\
+ BATU_VS |\
+ BATU_VP)
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
+
+/*
+ * U-Boot environment setup
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_CMD_EDITENV
+#define CONFIG_CMD_JFFS2
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024)
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \
+ + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SIZE 0x20000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+
+#define CONFIG_NETDEV eth1
+#define CONFIG_HOSTNAME ids8313
+#define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx"
+#define CONFIG_BOOTFILE "ids8313/uImage"
+#define CONFIG_UBOOTPATH "ids8313/u-boot.bin"
+#define CONFIG_FDTFILE "ids8313/ids8313.dtb"
+#define CONFIG_LOADADDR 0x400000
+#define CONFIG_CMD_ENV_FLAGS
+#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_HZ 1000
+
+/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_SYS_CBSIZE 1024
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ + sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#define CONFIG_SYS_MEMTEST_START 0x00001000
+#define CONFIG_SYS_MEMTEST_END 0x00C00000
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000
+#define CONFIG_MII
+#define CONFIG_LOADS_ECHO
+#define CONFIG_TIMESTAMP
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \\\"run nfsboot\\\" " \
+ "to mount root filesystem over NFS;echo"
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND "run boot_cramfs"
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE
+
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_DEV "0"
+
+/* mtdparts command line support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define CONFIG_MTD_DEVICE
+#define MTDIDS_DEFAULT "nor0=ff800000.flash,nand0=e1000000.flash"
+#define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:7m(dum)," \
+ "768k(BOOT-BIN)," \
+ "128k(BOOT-ENV),128k(BOOT-REDENV);" \
+ "e1000000.flash:-(ubi)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" __stringify(CONFIG_NETDEV) "\0" \
+ "ethprime=TSEC1\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot ${loadaddr} ${uboot}; " \
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +${filesize}; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +${filesize}; " \
+ "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " ${filesize}; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " +${filesize}; " \
+ "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \
+ " ${filesize}\0" \
+ "console=ttyS0\0" \
+ "fdtaddr=0x780000\0" \
+ "kernel_addr=ff800000\0" \
+ "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \
+ "setbootargs=setenv bootargs " \
+ "root=${rootdev} rw console=${console}," \
+ "${baudrate} ${othbootargs}\0" \
+ "setipargs=setenv bootargs root=${rootdev} rw " \
+ "nfsroot=${serverip}:${rootpath} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off " \
+ "console=${console},${baudrate} ${othbootargs}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv rootdev /dev/nfs;" \
+ "run setipargs;run addmtd;" \
+ "tftp ${loadaddr} ${bootfile};" \
+ "tftp ${fdtaddr} ${fdtfile};" \
+ "fdt addr ${fdtaddr};" \
+ "bootm ${loadaddr} - ${fdtaddr}"
+
+/* UBI Support */
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_MTD_PARTITIONS
+
+/* bootcount support */
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_I2C
+#define CONFIG_BOOTCOUNT_ALEN 1
+#define CONFIG_SYS_BOOTCOUNT_ADDR 0x9
+
+#define CONFIG_VERSION_VARIABLE
+
+#define CONFIG_FIT
+#define CONFIG_FIT_SIGNATURE
+#define CONFIG_CMD_FDT
+#define CONFIG_CMD_HASH
+#define CONFIG_RSA
+#define CONFIG_SHA1
+#define CONFIG_SHA256
+#define CONFIG_OF_CONTROL
+
+#endif /* __CONFIG_H */