powerpc/mpc85xx: software workaround for DDR erratum A-004468
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
index bc7e5e3..ce5924b 100644
--- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c
+++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
@@ -76,6 +76,9 @@
#if defined(CONFIG_SYS_FSL_ERRATUM_ESDHC111)
puts("Work-around for Erratum ESDHC111 enabled\n");
#endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A004468
+ puts("Work-around for Erratum A004468 enabled\n");
+#endif
#if defined(CONFIG_SYS_FSL_ERRATUM_ESDHC135)
puts("Work-around for Erratum ESDHC135 enabled\n");
#endif
diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c
index d54527a..8221481 100644
--- a/arch/powerpc/cpu/mpc85xx/fdt.c
+++ b/arch/powerpc/cpu/mpc85xx/fdt.c
@@ -48,7 +48,7 @@
{
int off;
ulong spin_tbl_addr = get_spin_phys_addr();
- u32 bootpg = determine_mp_bootpg();
+ u32 bootpg = determine_mp_bootpg(NULL);
u32 id = get_my_id();
const char *enable_method;
diff --git a/arch/powerpc/cpu/mpc85xx/mp.c b/arch/powerpc/cpu/mpc85xx/mp.c
index ffc2a9a..39adf8e 100644
--- a/arch/powerpc/cpu/mpc85xx/mp.c
+++ b/arch/powerpc/cpu/mpc85xx/mp.c
@@ -27,9 +27,11 @@
#include <asm/io.h>
#include <asm/mmu.h>
#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
#include "mp.h"
DECLARE_GLOBAL_DATA_PTR;
+u32 fsl_ddr_get_intl3r(void);
u32 get_my_id()
{
@@ -191,13 +193,68 @@
return 0;
}
-u32 determine_mp_bootpg(void)
+u32 determine_mp_bootpg(unsigned int *pagesize)
{
+ u32 bootpg;
+#ifdef CONFIG_SYS_FSL_ERRATUM_A004468
+ u32 svr = get_svr();
+ u32 granule_size, check;
+ struct law_entry e;
+#endif
+
/* if we have 4G or more of memory, put the boot page at 4Gb-4k */
if ((u64)gd->ram_size > 0xfffff000)
- return (0xfffff000);
+ bootpg = 0xfffff000;
+ else
+ bootpg = gd->ram_size - 4096;
+ if (pagesize)
+ *pagesize = 4096;
- return (gd->ram_size - 4096);
+#ifdef CONFIG_SYS_FSL_ERRATUM_A004468
+/*
+ * Erratum A004468 has two parts. The 3-way interleaving applies to T4240,
+ * to be fixed in rev 2.0. The 2-way interleaving applies to many SoCs. But
+ * the way boot page chosen in u-boot avoids hitting this erratum. So only
+ * thw workaround for 3-way interleaving is needed.
+ *
+ * To make sure boot page translation works with 3-Way DDR interleaving
+ * enforce a check for the following constrains
+ * 8K granule size requires BRSIZE=8K and
+ * bootpg >> log2(BRSIZE) %3 == 1
+ * 4K and 1K granule size requires BRSIZE=4K and
+ * bootpg >> log2(BRSIZE) %3 == 0
+ */
+ if (SVR_SOC_VER(svr) == SVR_T4240 && SVR_MAJ(svr) < 2) {
+ e = find_law(bootpg);
+ switch (e.trgt_id) {
+ case LAW_TRGT_IF_DDR_INTLV_123:
+ granule_size = fsl_ddr_get_intl3r() & 0x1f;
+ if (granule_size == FSL_DDR_3WAY_8KB_INTERLEAVING) {
+ if (pagesize)
+ *pagesize = 8192;
+ bootpg &= 0xffffe000; /* align to 8KB */
+ check = bootpg >> 13;
+ while ((check % 3) != 1)
+ check--;
+ bootpg = check << 13;
+ debug("Boot page (8K) at 0x%08x\n", bootpg);
+ break;
+ } else {
+ bootpg &= 0xfffff000; /* align to 4KB */
+ check = bootpg >> 12;
+ while ((check % 3) != 0)
+ check--;
+ bootpg = check << 12;
+ debug("Boot page (4K) at 0x%08x\n", bootpg);
+ }
+ break;
+ default:
+ break;
+ }
+ }
+#endif /* CONFIG_SYS_FSL_ERRATUM_A004468 */
+
+ return bootpg;
}
ulong get_spin_phys_addr(void)
@@ -219,9 +276,9 @@
}
#ifdef CONFIG_FSL_CORENET
-static void plat_mp_up(unsigned long bootpg)
+static void plat_mp_up(unsigned long bootpg, unsigned int pagesize)
{
- u32 cpu_up_mask, whoami;
+ u32 cpu_up_mask, whoami, brsize = LAW_SIZE_4K;
u32 *table = (u32 *)get_spin_virt_addr();
volatile ccsr_gur_t *gur;
volatile ccsr_local_t *ccm;
@@ -241,7 +298,11 @@
out_be32(&ccm->bstrl, bootpg);
e = find_law(bootpg);
- out_be32(&ccm->bstrar, LAW_EN | e.trgt_id << 20 | LAW_SIZE_4K);
+ /* pagesize is only 4K or 8K */
+ if (pagesize == 8192)
+ brsize = LAW_SIZE_8K;
+ out_be32(&ccm->bstrar, LAW_EN | e.trgt_id << 20 | brsize);
+ debug("BRSIZE is 0x%x\n", brsize);
/* readback to sync write */
in_be32(&ccm->bstrar);
@@ -294,7 +355,7 @@
#endif
}
#else
-static void plat_mp_up(unsigned long bootpg)
+static void plat_mp_up(unsigned long bootpg, unsigned int pagesize)
{
u32 up, cpu_up_mask, whoami;
u32 *table = (u32 *)get_spin_virt_addr();
@@ -374,7 +435,7 @@
void cpu_mp_lmb_reserve(struct lmb *lmb)
{
- u32 bootpg = determine_mp_bootpg();
+ u32 bootpg = determine_mp_bootpg(NULL);
lmb_reserve(lmb, bootpg, 4096);
}
@@ -383,8 +444,23 @@
{
extern ulong __secondary_start_page;
extern ulong __bootpg_addr;
+
ulong fixup = (ulong)&__secondary_start_page;
- u32 bootpg = determine_mp_bootpg();
+ u32 bootpg, bootpg_map, pagesize;
+
+ bootpg = determine_mp_bootpg(&pagesize);
+
+ /*
+ * pagesize is only 4K or 8K
+ * we only use the last 4K of boot page
+ * bootpg_map saves the address for the boot page
+ * 8K is used for the workaround of 3-way DDR interleaving
+ */
+
+ bootpg_map = bootpg;
+
+ if (pagesize == 8192)
+ bootpg += 4096; /* use 2nd half */
/* Some OSes expect secondary cores to be held in reset */
if (hold_cores_in_reset(0))
@@ -407,7 +483,7 @@
memcpy((void *)CONFIG_BPTR_VIRT_ADDR, (void *)fixup, 4096);
- plat_mp_up(bootpg);
+ plat_mp_up(bootpg_map, pagesize);
} else {
puts("WARNING: No reset page TLB. "
"Skipping secondary core setup\n");
diff --git a/arch/powerpc/cpu/mpc86xx/fdt.c b/arch/powerpc/cpu/mpc86xx/fdt.c
index 61f5110..2f955fe 100644
--- a/arch/powerpc/cpu/mpc86xx/fdt.c
+++ b/arch/powerpc/cpu/mpc86xx/fdt.c
@@ -20,7 +20,7 @@
{
#ifdef CONFIG_MP
int off;
- u32 bootpg = determine_mp_bootpg();
+ u32 bootpg = determine_mp_bootpg(NULL);
#endif
do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
diff --git a/arch/powerpc/cpu/mpc86xx/mp.c b/arch/powerpc/cpu/mpc86xx/mp.c
index 30c99eb..de705f0 100644
--- a/arch/powerpc/cpu/mpc86xx/mp.c
+++ b/arch/powerpc/cpu/mpc86xx/mp.c
@@ -90,8 +90,11 @@
return 1;
}
-u32 determine_mp_bootpg(void)
+u32 determine_mp_bootpg(unsigned int *pagesize)
{
+ if (pagesize)
+ *pagesize = 4096;
+
/* if we have 4G or more of memory, put the boot page at 4Gb-1M */
if ((u64)gd->ram_size > 0xfffff000)
return (0xfff00000);
@@ -101,7 +104,7 @@
void cpu_mp_lmb_reserve(struct lmb *lmb)
{
- u32 bootpg = determine_mp_bootpg();
+ u32 bootpg = determine_mp_bootpg(NULL);
/* tell u-boot we stole a page */
lmb_reserve(lmb, bootpg, 4096);
@@ -115,7 +118,7 @@
{
extern ulong __secondary_start_page;
ulong fixup = (ulong)&__secondary_start_page;
- u32 bootpg = determine_mp_bootpg();
+ u32 bootpg = determine_mp_bootpg(NULL);
u32 bootpg_va;
if (bootpg >= CONFIG_SYS_MAX_DDR_BAT_SIZE) {
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/util.c b/arch/powerpc/cpu/mpc8xxx/ddr/util.c
index afc5fae..940ffff 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/util.c
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/util.c
@@ -121,6 +121,16 @@
#endif
}
+u32 fsl_ddr_get_intl3r(void)
+{
+ u32 val = 0;
+#ifdef CONFIG_E6500
+ u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004);
+ val = *mcintl3r;
+#endif
+ return val;
+}
+
void board_add_ram_info(int use_default)
{
#if defined(CONFIG_MPC83xx)
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index ba13ddf..ecb1566 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -511,6 +511,7 @@
#define CONFIG_SYS_FSL_USB1_PHY_ENABLE
#define CONFIG_SYS_FSL_USB2_PHY_ENABLE
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
+#define CONFIG_SYS_FSL_ERRATUM_A004468
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
#elif defined(CONFIG_PPC_B4860)
diff --git a/arch/powerpc/include/asm/mp.h b/arch/powerpc/include/asm/mp.h
index fe490ba..9188ede 100644
--- a/arch/powerpc/include/asm/mp.h
+++ b/arch/powerpc/include/asm/mp.h
@@ -25,7 +25,7 @@
void setup_mp(void);
void cpu_mp_lmb_reserve(struct lmb *lmb);
-u32 determine_mp_bootpg(void);
+u32 determine_mp_bootpg(unsigned int *pagesize);
int is_core_disabled(int nr);
#ifdef CONFIG_E6500
diff --git a/arch/powerpc/lib/board.c b/arch/powerpc/lib/board.c
index b860141..ebf4008 100644
--- a/arch/powerpc/lib/board.c
+++ b/arch/powerpc/lib/board.c
@@ -440,8 +440,8 @@
* We need to make sure the location we intend to put secondary core
* boot code is reserved and not used by any part of u-boot
*/
- if (addr > determine_mp_bootpg()) {
- addr = determine_mp_bootpg();
+ if (addr > determine_mp_bootpg(NULL)) {
+ addr = determine_mp_bootpg(NULL);
debug("Reserving MP boot page to %08lx\n", addr);
}
#endif