| .. SPDX-License-Identifier: GPL-2.0+ |
| |
| U-Boot FIT Signature Verification |
| ================================= |
| |
| Introduction |
| ------------ |
| |
| FIT supports hashing of images so that these hashes can be checked on |
| loading. This protects against corruption of the image. However it does not |
| prevent the substitution of one image for another. |
| |
| The signature feature allows the hash to be signed with a private key such |
| that it can be verified using a public key later. Provided that the private |
| key is kept secret and the public key is stored in a non-volatile place, |
| any image can be verified in this way. |
| |
| See verified-boot.txt for more general information on verified boot. |
| |
| |
| Concepts |
| -------- |
| |
| Some familiarity with public key cryptography is assumed in this section. |
| |
| The procedure for signing is as follows: |
| |
| - hash an image in the FIT |
| - sign the hash with a private key to produce a signature |
| - store the resulting signature in the FIT |
| |
| The procedure for verification is: |
| |
| - read the FIT |
| - obtain the public key |
| - extract the signature from the FIT |
| - hash the image from the FIT |
| - verify (with the public key) that the extracted signature matches the |
| hash |
| |
| The signing is generally performed by mkimage, as part of making a firmware |
| image for the device. The verification is normally done in U-Boot on the |
| device. |
| |
| |
| Algorithms |
| ---------- |
| In principle any suitable algorithm can be used to sign and verify a hash. |
| U-Boot supports a few hashing and verification algorithms. See below for |
| details. |
| |
| While it is acceptable to bring in large cryptographic libraries such as |
| openssl on the host side (e.g. mkimage), it is not desirable for U-Boot. |
| For the run-time verification side, it is important to keep code and data |
| size as small as possible. |
| |
| For this reason the RSA image verification uses pre-processed public keys |
| which can be used with a very small amount of code - just some extraction |
| of data from the FDT and exponentiation mod n. Code size impact is a little |
| under 5KB on Tegra Seaboard, for example. |
| |
| It is relatively straightforward to add new algorithms if required. If |
| another RSA variant is needed, then it can be added with the |
| U_BOOT_CRYPTO_ALGO() macro. If another algorithm is needed (such as DSA) then |
| it can be placed in a directory alongside lib/rsa/, and its functions added |
| using U_BOOT_CRYPTO_ALGO(). |
| |
| |
| Creating an RSA key pair and certificate |
| ---------------------------------------- |
| To create a new public/private key pair, size 2048 bits:: |
| |
| $ openssl genpkey -algorithm RSA -out keys/dev.key \ |
| -pkeyopt rsa_keygen_bits:2048 -pkeyopt rsa_keygen_pubexp:65537 |
| |
| To create a certificate for this containing the public key:: |
| |
| $ openssl req -batch -new -x509 -key keys/dev.key -out keys/dev.crt |
| |
| If you like you can look at the public key also:: |
| |
| $ openssl rsa -in keys/dev.key -pubout |
| |
| |
| Public Key Storage |
| ------------------ |
| In order to verify an image that has been signed with a public key we need to |
| have a trusted public key. This cannot be stored in the signed image, since |
| it would be easy to alter. For this implementation we choose to store the |
| public key in U-Boot's control FDT (using CONFIG_OF_CONTROL). |
| |
| Public keys should be stored as sub-nodes in a /signature node. Required |
| properties are: |
| |
| algo |
| Algorithm name (e.g. "sha256,rsa2048" or "sha512,ecdsa256") |
| |
| Optional properties are: |
| |
| key-name-hint |
| Name of key used for signing. This is only a hint since it |
| is possible for the name to be changed. Verification can proceed by checking |
| all available signing keys until one matches. |
| |
| required |
| If present this indicates that the key must be verified for the |
| image / configuration to be considered valid. Only required keys are |
| normally verified by the FIT image booting algorithm. Valid values are |
| "image" to force verification of all images, and "conf" to force verification |
| of the selected configuration (which then relies on hashes in the images to |
| verify those). |
| |
| Each signing algorithm has its own additional properties. |
| |
| For RSA the following are mandatory: |
| |
| rsa,num-bits |
| Number of key bits (e.g. 2048) |
| |
| rsa,modulus |
| Modulus (N) as a big-endian multi-word integer |
| |
| rsa,exponent |
| Public exponent (E) as a 64 bit unsigned integer |
| |
| rsa,r-squared |
| (2^num-bits)^2 as a big-endian multi-word integer |
| |
| rsa,n0-inverse |
| -1 / modulus[0] mod 2^32 |
| |
| For ECDSA the following are mandatory: |
| |
| ecdsa,curve |
| Name of ECDSA curve (e.g. "prime256v1") |
| |
| ecdsa,x-point |
| Public key X coordinate as a big-endian multi-word integer |
| |
| ecdsa,y-point |
| Public key Y coordinate as a big-endian multi-word integer |
| |
| These parameters can be added to a binary device tree using parameter -K of the |
| mkimage command:: |
| |
| tools/mkimage -f fit.its -K control.dtb -k keys -r image.fit |
| |
| Here is an example of a generated device tree node:: |
| |
| signature { |
| key-dev { |
| required = "conf"; |
| algo = "sha256,rsa2048"; |
| rsa,r-squared = <0xb76d1acf 0xa1763ca5 0xeb2f126 |
| 0x742edc80 0xd3f42177 0x9741d9d9 |
| 0x35bb476e 0xff41c718 0xd3801430 |
| 0xf22537cb 0xa7e79960 0xae32a043 |
| 0x7da1427a 0x341d6492 0x3c2762f5 |
| 0xaac04726 0x5b262d96 0xf984e86d |
| 0xb99443c7 0x17080c33 0x940f6892 |
| 0xd57a95d1 0x6ea7b691 0xc5038fa8 |
| 0x6bb48a6e 0x73f1b1ea 0x37160841 |
| 0xe05715ce 0xa7c45bbd 0x690d82d5 |
| 0x99c2454c 0x6ff117b3 0xd830683b |
| 0x3f81c9cf 0x1ca38a91 0x0c3392e4 |
| 0xd817c625 0x7b8e9a24 0x175b89ea |
| 0xad79f3dc 0x4d50d7b4 0x9d4e90f8 |
| 0xad9e2939 0xc165d6a4 0x0ada7e1b |
| 0xfb1bf495 0xfc3131c2 0xb8c6e604 |
| 0xc2761124 0xf63de4a6 0x0e9565f9 |
| 0xc8e53761 0x7e7a37a5 0xe99dcdae |
| 0x9aff7e1e 0xbd44b13d 0x6b0e6aa4 |
| 0x038907e4 0x8e0d6850 0xef51bc20 |
| 0xf73c94af 0x88bea7b1 0xcbbb1b30 |
| 0xd024b7f3>; |
| rsa,modulus = <0xc0711d6cb 0x9e86db7f 0x45986dbe |
| 0x023f1e8c9 0xe1a4c4d0 0x8a0dfdc9 |
| 0x023ba0c48 0x06815f6a 0x5caa0654 |
| 0x07078c4b7 0x3d154853 0x40729023 |
| 0x0b007c8fe 0x5a3647e5 0x23b41e20 |
| 0x024720591 0x66915305 0x0e0b29b0 |
| 0x0de2ad30d 0x8589430f 0xb1590325 |
| 0x0fb9f5d5e 0x9eba752a 0xd88e6de9 |
| 0x056b3dcc6 0x9a6b8e61 0x6784f61f |
| 0x000f39c21 0x5eec6b33 0xd78e4f78 |
| 0x0921a305f 0xaa2cc27e 0x1ca917af |
| 0x06e1134f4 0xd48cac77 0x4e914d07 |
| 0x0f707aa5a 0x0d141f41 0x84677f1d |
| 0x0ad47a049 0x028aedb6 0xd5536fcf |
| 0x03fef1e4f 0x133a03d2 0xfd7a750a |
| 0x0f9159732 0xd207812e 0x6a807375 |
| 0x06434230d 0xc8e22dad 0x9f29b3d6 |
| 0x07c44ac2b 0xfa2aad88 0xe2429504 |
| 0x041febd41 0x85d0d142 0x7b194d65 |
| 0x06e5d55ea 0x41116961 0xf3181dde |
| 0x068bf5fbc 0x3dd82047 0x00ee647e |
| 0x0d7a44ab3>; |
| rsa,exponent = <0x00 0x10001>; |
| rsa,n0-inverse = <0xb3928b85>; |
| rsa,num-bits = <0x800>; |
| key-name-hint = "dev"; |
| }; |
| }; |
| |
| |
| Signed Configurations |
| --------------------- |
| While signing images is useful, it does not provide complete protection |
| against several types of attack. For example, it is possible to create a |
| FIT with the same signed images, but with the configuration changed such |
| that a different one is selected (mix and match attack). It is also possible |
| to substitute a signed image from an older FIT version into a newer FIT |
| (roll-back attack). |
| |
| As an example, consider this FIT:: |
| |
| / { |
| images { |
| kernel-1 { |
| data = <data for kernel1> |
| signature-1 { |
| algo = "sha256,rsa2048"; |
| value = <...kernel signature 1...> |
| }; |
| }; |
| kernel-2 { |
| data = <data for kernel2> |
| signature-1 { |
| algo = "sha256,rsa2048"; |
| value = <...kernel signature 2...> |
| }; |
| }; |
| fdt-1 { |
| data = <data for fdt1>; |
| signature-1 { |
| algo = "sha256,rsa2048"; |
| value = <...fdt signature 1...> |
| }; |
| }; |
| fdt-2 { |
| data = <data for fdt2>; |
| signature-1 { |
| algo = "sha256,rsa2048"; |
| value = <...fdt signature 2...> |
| }; |
| }; |
| }; |
| configurations { |
| default = "conf-1"; |
| conf-1 { |
| kernel = "kernel-1"; |
| fdt = "fdt-1"; |
| }; |
| conf-2 { |
| kernel = "kernel-2"; |
| fdt = "fdt-2"; |
| }; |
| }; |
| }; |
| |
| Since both kernels are signed it is easy for an attacker to add a new |
| configuration 3 with kernel 1 and fdt 2:: |
| |
| configurations { |
| default = "conf-1"; |
| conf-1 { |
| kernel = "kernel-1"; |
| fdt = "fdt-1"; |
| }; |
| conf-2 { |
| kernel = "kernel-2"; |
| fdt = "fdt-2"; |
| }; |
| conf-3 { |
| kernel = "kernel-1"; |
| fdt = "fdt-2"; |
| }; |
| }; |
| |
| With signed images, nothing protects against this. Whether it gains an |
| advantage for the attacker is debatable, but it is not secure. |
| |
| To solve this problem, we support signed configurations. In this case it |
| is the configurations that are signed, not the image. Each image has its |
| own hash, and we include the hash in the configuration signature. |
| |
| So the above example is adjusted to look like this:: |
| |
| / { |
| images { |
| kernel-1 { |
| data = <data for kernel1> |
| hash-1 { |
| algo = "sha256"; |
| value = <...kernel hash 1...> |
| }; |
| }; |
| kernel-2 { |
| data = <data for kernel2> |
| hash-1 { |
| algo = "sha256"; |
| value = <...kernel hash 2...> |
| }; |
| }; |
| fdt-1 { |
| data = <data for fdt1>; |
| hash-1 { |
| algo = "sha256"; |
| value = <...fdt hash 1...> |
| }; |
| }; |
| fdt-2 { |
| data = <data for fdt2>; |
| hash-1 { |
| algo = "sha256"; |
| value = <...fdt hash 2...> |
| }; |
| }; |
| }; |
| configurations { |
| default = "conf-1"; |
| conf-1 { |
| kernel = "kernel-1"; |
| fdt = "fdt-1"; |
| signature-1 { |
| algo = "sha256,rsa2048"; |
| value = <...conf 1 signature...>; |
| }; |
| }; |
| conf-2 { |
| kernel = "kernel-2"; |
| fdt = "fdt-2"; |
| signature-1 { |
| algo = "sha256,rsa2048"; |
| value = <...conf 1 signature...>; |
| }; |
| }; |
| }; |
| }; |
| |
| |
| You can see that we have added hashes for all images (since they are no |
| longer signed), and a signature to each configuration. In the above example, |
| mkimage will sign configurations/conf-1, the kernel and fdt that are |
| pointed to by the configuration (/images/kernel-1, /images/kernel-1/hash-1, |
| /images/fdt-1, /images/fdt-1/hash-1) and the root structure of the image |
| (so that it isn't possible to add or remove root nodes). The signature is |
| written into /configurations/conf-1/signature-1/value. It can easily be |
| verified later even if the FIT has been signed with other keys in the |
| meantime. |
| |
| |
| Details |
| ------- |
| The signature node contains a property ('hashed-nodes') which lists all the |
| nodes that the signature was made over. The image is walked in order and each |
| tag processed as follows: |
| |
| DTB_BEGIN_NODE |
| The tag and the following name are included in the signature |
| if the node or its parent are present in 'hashed-nodes' |
| |
| DTB_END_NODE |
| The tag is included in the signature if the node or its parent |
| are present in 'hashed-nodes' |
| |
| DTB_PROPERTY |
| The tag, the length word, the offset in the string table, and |
| the data are all included if the current node is present in 'hashed-nodes' |
| and the property name is not 'data'. |
| |
| DTB_END |
| The tag is always included in the signature. |
| |
| DTB_NOP |
| The tag is included in the signature if the current node is present |
| in 'hashed-nodes' |
| |
| In addition, the signature contains a property 'hashed-strings' which contains |
| the offset and length in the string table of the strings that are to be |
| included in the signature (this is done last). |
| |
| IMPORTANT: To verify the signature outside u-boot, it is vital to not only |
| calculate the hash of the image and verify the signature with that, but also to |
| calculate the hashes of the kernel, fdt, and ramdisk images and check those |
| match the hash values in the corresponding 'hash*' subnodes. |
| |
| |
| Verification |
| ------------ |
| FITs are verified when loaded. After the configuration is selected a list |
| of required images is produced. If there are 'required' public keys, then |
| each image must be verified against those keys. This means that every image |
| that might be used by the target needs to be signed with 'required' keys. |
| |
| This happens automatically as part of a bootm command when FITs are used. |
| |
| For Signed Configurations, the default verification behavior can be changed by |
| the following optional property in /signature node in U-Boot's control FDT. |
| |
| required-mode |
| Valid values are "any" to allow verified boot to succeed if |
| the selected configuration is signed by any of the 'required' keys, and "all" |
| to allow verified boot to succeed if the selected configuration is signed by |
| all of the 'required' keys. |
| |
| This property can be added to a binary device tree using fdtput as shown in |
| below examples:: |
| |
| fdtput -t s control.dtb /signature required-mode any |
| fdtput -t s control.dtb /signature required-mode all |
| |
| |
| Enabling FIT Verification |
| ------------------------- |
| In addition to the options to enable FIT itself, the following CONFIGs must |
| be enabled: |
| |
| CONFIG_FIT_SIGNATURE |
| enable signing and verification in FITs |
| |
| CONFIG_RSA |
| enable RSA algorithm for signing |
| |
| CONFIG_ECDSA |
| enable ECDSA algorithm for signing |
| |
| WARNING: When relying on signed FIT images with required signature check |
| the legacy image format is default disabled by not defining |
| CONFIG_LEGACY_IMAGE_FORMAT |
| |
| |
| Testing |
| ------- |
| |
| An easy way to test signing and verification is to use the test script |
| provided in test/vboot/vboot_test.sh. This uses sandbox (a special version |
| of U-Boot which runs under Linux) to show the operation of a 'bootm' |
| command loading and verifying images. |
| |
| A sample run is show below:: |
| |
| $ make O=sandbox sandbox_config |
| $ make O=sandbox |
| $ O=sandbox ./test/vboot/vboot_test.sh |
| |
| |
| Simple Verified Boot Test |
| ------------------------- |
| |
| Please see :doc:`verified-boot` for more information:: |
| |
| /home/hs/ids/u-boot/sandbox/tools/mkimage -D -I dts -O dtb -p 2000 |
| Build keys |
| do sha1 test |
| Build FIT with signed images |
| Test Verified Boot Run: unsigned signatures:: OK |
| Sign images |
| Test Verified Boot Run: signed images: OK |
| Build FIT with signed configuration |
| Test Verified Boot Run: unsigned config: OK |
| Sign images |
| Test Verified Boot Run: signed config: OK |
| check signed config on the host |
| Signature check OK |
| OK |
| Test Verified Boot Run: signed config: OK |
| Test Verified Boot Run: signed config with bad hash: OK |
| do sha256 test |
| Build FIT with signed images |
| Test Verified Boot Run: unsigned signatures:: OK |
| Sign images |
| Test Verified Boot Run: signed images: OK |
| Build FIT with signed configuration |
| Test Verified Boot Run: unsigned config: OK |
| Sign images |
| Test Verified Boot Run: signed config: OK |
| check signed config on the host |
| Signature check OK |
| OK |
| Test Verified Boot Run: signed config: OK |
| Test Verified Boot Run: signed config with bad hash: OK |
| |
| Test passed |
| |
| |
| Software signing: keydir vs keyfile |
| ----------------------------------- |
| |
| In the simplest case, signing is done by giving mkimage the 'keyfile'. This is |
| the path to a file containing the signing key. |
| |
| The alternative is to pass the 'keydir' argument. In this case the filename of |
| the key is derived from the 'keydir' and the "key-name-hint" property in the |
| FIT. In this case the "key-name-hint" property is mandatory, and the key must |
| exist in "<keydir>/<key-name-hint>.<ext>" Here the extension "ext" is |
| specific to the signing algorithm. |
| |
| |
| Hardware Signing with PKCS#11 or with HSM |
| ----------------------------------------- |
| |
| Securely managing private signing keys can challenging, especially when the |
| keys are stored on the file system of a computer that is connected to the |
| Internet. If an attacker is able to steal the key, they can sign malicious FIT |
| images which will appear genuine to your devices. |
| |
| An alternative solution is to keep your signing key securely stored on hardware |
| device like a smartcard, USB token or Hardware Security Module (HSM) and have |
| them perform the signing. PKCS#11 is standard for interfacing with these crypto |
| device. |
| |
| Requirements: |
| - Smartcard/USB token/HSM which can work with some openssl engine |
| - openssl |
| |
| For pkcs11 engine usage: |
| - libp11 (provides pkcs11 engine) |
| - p11-kit (recommended to simplify setup) |
| - opensc (for smartcards and smartcard like USB devices) |
| - gnutls (recommended for key generation, p11tool) |
| |
| For generic HSMs respective openssl engine must be installed and locateable by |
| openssl. This may require setting up LD_LIBRARY_PATH if engine is not installed |
| to openssl's default search paths. |
| |
| PKCS11 engine support forms "key id" based on "keydir" and with |
| "key-name-hint". "key-name-hint" is used as "object" name (if not defined in |
| keydir). "keydir" (if defined) is used to define (prefix for) which PKCS11 source |
| is being used for lookup up for the key. |
| |
| PKCS11 engine key ids |
| "pkcs11:<keydir>;object=<key-name-hint>;type=<public|private>" |
| |
| or, if keydir contains "object=" |
| "pkcs11:<keydir>;type=<public|private>" |
| |
| or |
| "pkcs11:object=<key-name-hint>;type=<public|private>", |
| |
| Generic HSM engine support forms "key id" based on "keydir" and with |
| "key-name-hint". If "keydir" is specified for mkimage it is used as a prefix in |
| "key id" and is appended with "key-name-hint". |
| |
| Generic engine key ids: |
| "<keydir><key-name-hint>" |
| |
| or |
| "< key-name-hint>" |
| |
| In order to set the pin in the HSM, an environment variable "MKIMAGE_SIGN_PIN" |
| can be specified. |
| |
| The following examples use the Nitrokey Pro using pkcs11 engine. Instructions |
| for other devices may vary. |
| |
| Notes on pkcs11 engine setup: |
| |
| Make sure p11-kit, opensc are installed and that p11-kit is setup to use opensc. |
| /usr/share/p11-kit/modules/opensc.module should be present on your system. |
| |
| |
| Generating Keys On the Nitrokey:: |
| |
| $ gpg --card-edit |
| |
| Reader ...........: Nitrokey Nitrokey Pro (xxxxxxxx0000000000000000) 00 00 |
| Application ID ...: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| Version ..........: 2.1 |
| Manufacturer .....: ZeitControl |
| Serial number ....: xxxxxxxx |
| Name of cardholder: [not set] |
| Language prefs ...: de |
| Sex ..............: unspecified |
| URL of public key : [not set] |
| Login data .......: [not set] |
| Signature PIN ....: forced |
| Key attributes ...: rsa2048 rsa2048 rsa2048 |
| Max. PIN lengths .: 32 32 32 |
| PIN retry counter : 3 0 3 |
| Signature counter : 0 |
| Signature key ....: [none] |
| Encryption key....: [none] |
| Authentication key: [none] |
| General key info..: [none] |
| |
| gpg/card> generate |
| Make off-card backup of encryption key? (Y/n) n |
| |
| Please note that the factory settings of the PINs are |
| PIN = '123456' Admin PIN = '12345678' |
| You should change them using the command --change-pin |
| |
| What keysize do you want for the Signature key? (2048) 4096 |
| The card will now be re-configured to generate a key of 4096 bits |
| Note: There is no guarantee that the card supports the requested size. |
| If the key generation does not succeed, please check the |
| documentation of your card to see what sizes are allowed. |
| What keysize do you want for the Encryption key? (2048) 4096 |
| The card will now be re-configured to generate a key of 4096 bits |
| What keysize do you want for the Authentication key? (2048) 4096 |
| The card will now be re-configured to generate a key of 4096 bits |
| Please specify how long the key should be valid. |
| 0 = key does not expire |
| <n> = key expires in n days |
| <n>w = key expires in n weeks |
| <n>m = key expires in n months |
| <n>y = key expires in n years |
| Key is valid for? (0) |
| Key does not expire at all |
| Is this correct? (y/N) y |
| |
| GnuPG needs to construct a user ID to identify your key. |
| |
| Real name: John Doe |
| Email address: john.doe@email.com |
| Comment: |
| You selected this USER-ID: |
| "John Doe <john.doe@email.com>" |
| |
| Change (N)ame, (C)omment, (E)mail or (O)kay/(Q)uit? o |
| |
| |
| Using p11tool to get the token URL: |
| |
| Depending on system configuration, gpg-agent may need to be killed first:: |
| |
| $ p11tool --provider /usr/lib/opensc-pkcs11.so --list-tokens |
| Token 0: |
| URL: pkcs11:model=PKCS%2315%20emulated;manufacturer=ZeitControl;serial=000xxxxxxxxx;token=OpenPGP%20card%20%28User%20PIN%20%28sig%29%29 |
| Label: OpenPGP card (User PIN (sig)) |
| Type: Hardware token |
| Manufacturer: ZeitControl |
| Model: PKCS#15 emulated |
| Serial: 000xxxxxxxxx |
| Module: (null) |
| |
| |
| Token 1: |
| URL: pkcs11:model=PKCS%2315%20emulated;manufacturer=ZeitControl;serial=000xxxxxxxxx;token=OpenPGP%20card%20%28User%20PIN%29 |
| Label: OpenPGP card (User PIN) |
| Type: Hardware token |
| Manufacturer: ZeitControl |
| Model: PKCS#15 emulated |
| Serial: 000xxxxxxxxx |
| Module: (null) |
| |
| Use the portion of the signature token URL after "pkcs11:" as the keydir argument (-k) to mkimage below. |
| |
| |
| Use the URL of the token to list the private keys:: |
| |
| $ p11tool --login --provider /usr/lib/opensc-pkcs11.so --list-privkeys \ |
| "pkcs11:model=PKCS%2315%20emulated;manufacturer=ZeitControl;serial=000xxxxxxxxx;token=OpenPGP%20card%20%28User%20PIN%20%28sig%29%29" |
| Token 'OpenPGP card (User PIN (sig))' with URL 'pkcs11:model=PKCS%2315%20emulated;manufacturer=ZeitControl;serial=000xxxxxxxxx;token=OpenPGP%20card%20%28User%20PIN%20%28sig%29%29' requires user PIN |
| Enter PIN: |
| Object 0: |
| URL: pkcs11:model=PKCS%2315%20emulated;manufacturer=ZeitControl;serial=000xxxxxxxxx;token=OpenPGP%20card%20%28User%20PIN%20%28sig%29%29;id=%01;object=Signature%20key;type=private |
| Type: Private key |
| Label: Signature key |
| Flags: CKA_PRIVATE; CKA_NEVER_EXTRACTABLE; CKA_SENSITIVE; |
| ID: 01 |
| |
| Use the label, in this case "Signature key" as the key-name-hint in your FIT. |
| |
| Create the fitImage:: |
| |
| $ ./tools/mkimage -f fit-image.its fitImage |
| |
| |
| Sign the fitImage with the hardware key:: |
| |
| $ ./tools/mkimage -F -k \ |
| "pkcs11:model=PKCS%2315%20emulated;manufacturer=ZeitControl;serial=000xxxxxxxxx;token=OpenPGP%20card%20%28User%20PIN%20%28sig%29%29" \ |
| -K u-boot.dtb -N pkcs11 -r fitImage |
| |
| |
| Future Work |
| ----------- |
| |
| - Roll-back protection using a TPM is done using the tpm command. This can |
| be scripted, but we might consider a default way of doing this, built into |
| bootm. |
| |
| |
| Possible Future Work |
| -------------------- |
| |
| - More sandbox tests for failure modes |
| - Passwords for keys/certificates |
| - Perhaps implement OAEP |
| - Enhance bootm to permit scripted signature verification (so that a script |
| can verify an image but not actually boot it) |
| |
| |
| .. sectionauthor:: Simon Glass <sjg@chromium.org>, 1-1-13 |