armv8/ls2080ardb: Enable VID support

This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.

Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
index 4f0fdfd..1d3b336 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
@@ -180,6 +180,10 @@
 	u8	res_008[0x20-0x8];
 	u32	gpporcr1;	/* General-purpose POR configuration */
 	u32	gpporcr2;	/* General-purpose POR configuration 2 */
+#define FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT	25
+#define FSL_CHASSIS3_DCFG_FUSESR_VID_MASK	0x1F
+#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT	20
+#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK	0x1F
 	u32	dcfg_fusesr;	/* Fuse status register */
 	u32	gpporcr3;
 	u32	gpporcr4;
diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c
index a6a132a..2f29795 100644
--- a/board/freescale/common/vid.c
+++ b/board/freescale/common/vid.c
@@ -10,6 +10,8 @@
 #include <asm/io.h>
 #ifdef CONFIG_LS1043A
 #include <asm/arch/immap_lsch2.h>
+#elif defined(CONFIG_FSL_LSCH3)
+#include <asm/arch/immap_lsch3.h>
 #else
 #include <asm/immap_85xx.h>
 #endif
@@ -285,7 +287,7 @@
 int adjust_vdd(ulong vdd_override)
 {
 	int re_enable = disable_interrupts();
-#ifdef CONFIG_LS1043A
+#if defined(CONFIG_LS1043A) || defined(CONFIG_FSL_LSCH3)
 	struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
 #else
 	ccsr_gur_t __iomem *gur =
@@ -362,7 +364,11 @@
 	}
 
 	/* get the voltage ID from fuse status register */
+#ifdef CONFIG_FSL_LSCH3
+	fusesr = in_le32(&gur->dcfg_fusesr);
+#else
 	fusesr = in_be32(&gur->dcfg_fusesr);
+#endif
 	/*
 	 * VID is used according to the table below
 	 *                ---------------------------------------
@@ -387,6 +393,13 @@
 		vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) &
 			FSL_CHASSIS2_DCFG_FUSESR_VID_MASK;
 	}
+#elif defined(CONFIG_FSL_LSCH3)
+	vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT) &
+		FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK;
+	if ((vid == 0) || (vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK)) {
+		vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT) &
+			FSL_CHASSIS3_DCFG_FUSESR_VID_MASK;
+	}
 #else
 	vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
 		FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
diff --git a/board/freescale/ls2080ardb/ls2080ardb.c b/board/freescale/ls2080ardb/ls2080ardb.c
index ec4b74c..8201048 100644
--- a/board/freescale/ls2080ardb/ls2080ardb.c
+++ b/board/freescale/ls2080ardb/ls2080ardb.c
@@ -22,6 +22,7 @@
 
 #include "../common/qixis.h"
 #include "ls2080ardb_qixis.h"
+#include "../common/vid.h"
 
 #define PIN_MUX_SEL_SDHC	0x00
 #define PIN_MUX_SEL_DSPI	0x0a
@@ -123,6 +124,11 @@
 	return 0;
 }
 
+int i2c_multiplexer_select_vid_channel(u8 channel)
+{
+	return select_i2c_ch_pca9547(channel);
+}
+
 int config_board_mux(int ctrl_type)
 {
 	u8 reg5;
@@ -189,6 +195,9 @@
 	if (hwconfig("sdhc"))
 		config_board_mux(MUX_TYPE_SDHC);
 
+	if (adjust_vdd(0))
+		printf("Warning: Adjusting core voltage failed.\n");
+
 	return 0;
 }
 
diff --git a/include/configs/ls2080ardb.h b/include/configs/ls2080ardb.h
index ce1d900..15a1172 100644
--- a/include/configs/ls2080ardb.h
+++ b/include/configs/ls2080ardb.h
@@ -14,6 +14,22 @@
 
 #define CONFIG_DISPLAY_BOARDINFO
 
+#define I2C_MUX_CH_VOL_MONITOR		0xa
+#define I2C_VOL_MONITOR_ADDR		0x38
+#define CONFIG_VOL_MONITOR_IR36021_READ
+#define CONFIG_VOL_MONITOR_IR36021_SET
+
+#define CONFIG_VID_FLS_ENV		"ls2080ardb_vdd_mv"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_VID
+#endif
+/* step the IR regulator in 5mV increments */
+#define IR_VDD_STEP_DOWN		5
+#define IR_VDD_STEP_UP			5
+/* The lowest and highest voltage allowed for LS2080ARDB */
+#define VDD_MV_MIN			819
+#define VDD_MV_MAX			1212
+
 #ifndef __ASSEMBLY__
 unsigned long get_board_sys_clk(void);
 #endif