Add support for STX GP3SSA (stxssa) Board with 4 MiB flash.
Signed-off-by: Wolfgang Denk <wd@denx.de>
diff --git a/Makefile b/Makefile
index 2fe9a46..356fb91 100644
--- a/Makefile
+++ b/Makefile
@@ -1771,8 +1771,16 @@
stxgp3_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc85xx stxgp3
-stxssa_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc mpc85xx stxssa
+stxssa_config \
+stxssa_4M_config: unconfig
+ @mkdir -p $(obj)include
+ @if [ "$(findstring _4M_,$@)" ] ; then \
+ echo "#define CONFIG_STXSSA_4M" >>$(obj)include/config.h ; \
+ echo "... with 4 MiB flash memory" ; \
+ else \
+ >$(obj)include/config.h ; \
+ fi
+ @$(MKCONFIG) -a stxssa ppc mpc85xx stxssa
TQM8540_config \
TQM8541_config \
diff --git a/board/stxssa/config.mk b/board/stxssa/config.mk
index 30f42c5..5f4fc740 100644
--- a/board/stxssa/config.mk
+++ b/board/stxssa/config.mk
@@ -22,13 +22,12 @@
# MA 02111-1307 USA
#
-#
# default CCARBAR is at 0xff700000
# assume U-Boot is less than 0.5MB
# U-Boot is less than 256K, so push
# it further up into the flash
#
-TEXT_BASE = 0xfffC0000
+TEXT_BASE = 0xFFFC0000
PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
PLATFORM_CPPFLAGS += -DCONFIG_E500=1
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 8624f4b..1978a32 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -80,16 +80,20 @@
* This address, however, is used to configure a 256M local bus
* window that includes the Config latch below.
*/
-#define CFG_LBC_OPTION_BASE 0xf0000000 /* Localbus Extension */
+#define CFG_LBC_OPTION_BASE 0xF0000000 /* Localbus Extension */
#define CFG_LBC_OPTION_SIZE 256 /* 256MB */
/* There are various flash options used, we configure for the largest,
* which is 64Mbytes. The CFI works fine and will discover the proper
* sizes.
*/
-#define CFG_FLASH_BASE 0xFC000000 /* start of FLASH 64M */
-#define CFG_BR0_PRELIM 0xFC001801 /* port size 32bit */
-#define CFG_OR0_PRELIM 0xFC000FF7 /* 64 MB Flash */
+#ifdef CONFIG_STXSSA_4M
+#define CFG_FLASH_BASE 0xFFC00000 /* start of 4 MiB flash */
+#else
+#define CFG_FLASH_BASE 0xFC000000 /* start of 64 MiB flash */
+#endif
+#define CFG_BR0_PRELIM (CFG_FLASH_BASE | 0x1801) /* port size 32bit */
+#define CFG_OR0_PRELIM (CFG_FLASH_BASE | 0x0FF7)
#define CFG_FLASH_CFI 1
#define CFG_FLASH_CFI_DRIVER 1
@@ -104,9 +108,9 @@
/* The configuration latch is Chip Select 1.
* It's an 8-bit latch in the lower 8 bits of the word.
*/
-#define CFG_LBC_CFGLATCH_BASE 0xfb000000 /* Base of config latch */
-#define CFG_BR1_PRELIM 0xfb001801 /* 32-bit port */
-#define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */
+#define CFG_LBC_CFGLATCH_BASE 0xFB000000 /* Base of config latch */
+#define CFG_BR1_PRELIM 0xFB001801 /* 32-bit port */
+#define CFG_OR1_PRELIM 0xFFFF0FF7 /* 64K is enough */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
@@ -300,17 +304,20 @@
/* Environment - default config is in flash, see below */
#if 0 /* in EEPROM */
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0
-#define CFG_ENV_SIZE 2048
+# define CFG_ENV_IS_IN_EEPROM 1
+# define CFG_ENV_OFFSET 0
+# define CFG_ENV_SIZE 2048
#else /* in flash */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SECT_SIZE 0x40000
-
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+# define CFG_ENV_IS_IN_FLASH 1
+# ifdef CONFIG_STXSSA_4M
+# define CFG_ENV_SECT_SIZE 0x20000
+# else /* default configuration - 64 MiB flash */
+# define CFG_ENV_SECT_SIZE 0x40000
+# endif
+# define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
+# define CFG_ENV_SIZE 0x4000
+# define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE)
+# define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */