Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
arch/arm/cpu/armv7/config.mk
board/ti/am43xx/mux.c
include/configs/am43xx_evm.h
Signed-off-by: Tom Rini <trini@ti.com>
diff --git a/README b/README
index f51f17e..ff49260 100644
--- a/README
+++ b/README
@@ -1741,7 +1741,7 @@
If this option is set, then U-Boot will prevent the environment
variable "splashimage" from being set to a problematic address
- (see README.displaying-bmps and README.arm-unaligned-accesses).
+ (see README.displaying-bmps).
This option is useful for targets where, due to alignment
restrictions, an improperly aligned BMP image will cause a data
abort. If you think you will not have problems with unaligned
@@ -3742,12 +3742,6 @@
its config.mk file). If you find problems enabling this option on
your board please report the problem and send patches!
-- CONFIG_SYS_SYM_OFFSETS
- This is set by architectures that use offsets for link symbols
- instead of absolute values. So bss_start is obtained using an
- offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
- directly. You should not need to touch this setting.
-
- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
This is set by OMAP boards for the max time that reset should
be asserted. See doc/README.omap-reset-time for details on how
diff --git a/arch/arm/cpu/arm1136/start.S b/arch/arm/cpu/arm1136/start.S
index 00d1b30..3e2358e 100644
--- a/arch/arm/cpu/arm1136/start.S
+++ b/arch/arm/cpu/arm1136/start.S
@@ -70,32 +70,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -295,7 +269,6 @@
#ifdef CONFIG_SPL_BUILD
.align 5
do_hang:
- ldr sp, _TEXT_BASE /* use 32 words about stack */
bl hang /* hang and never return */
#else /* !CONFIG_SPL_BUILD */
.align 5
diff --git a/arch/arm/cpu/arm1136/u-boot-spl.lds b/arch/arm/cpu/arm1136/u-boot-spl.lds
index bccde73..0299902 100644
--- a/arch/arm/cpu/arm1136/u-boot-spl.lds
+++ b/arch/arm/cpu/arm1136/u-boot-spl.lds
@@ -33,7 +33,11 @@
.data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
. = ALIGN(4);
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ }
.bss :
{
diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S
index ffd7dd0..ce62011 100644
--- a/arch/arm/cpu/arm1176/start.S
+++ b/arch/arm/cpu/arm1176/start.S
@@ -77,33 +77,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S
index f180eb8..1a34842 100644
--- a/arch/arm/cpu/arm720t/start.S
+++ b/arch/arm/cpu/arm720t/start.S
@@ -67,32 +67,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
diff --git a/arch/arm/cpu/arm920t/ep93xx/u-boot.lds b/arch/arm/cpu/arm920t/ep93xx/u-boot.lds
index 4bed4fc..9699404 100644
--- a/arch/arm/cpu/arm920t/ep93xx/u-boot.lds
+++ b/arch/arm/cpu/arm920t/ep93xx/u-boot.lds
@@ -50,5 +50,8 @@
.bss : { *(.bss*) }
__bss_end = .;
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
}
diff --git a/arch/arm/cpu/arm920t/start.S b/arch/arm/cpu/arm920t/start.S
index a67b659..7bf094a 100644
--- a/arch/arm/cpu/arm920t/start.S
+++ b/arch/arm/cpu/arm920t/start.S
@@ -55,32 +55,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
diff --git a/arch/arm/cpu/arm926ejs/at91/lowlevel_init.S b/arch/arm/cpu/arm926ejs/at91/lowlevel_init.S
index e83968f..a9ec81a 100644
--- a/arch/arm/cpu/arm926ejs/at91/lowlevel_init.S
+++ b/arch/arm/cpu/arm926ejs/at91/lowlevel_init.S
@@ -26,27 +26,18 @@
#define CONFIG_SYS_MATRIX_EBICSA_VAL CONFIG_SYS_MATRIX_EBI0CSA_VAL
#endif
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE
-
.globl lowlevel_init
.type lowlevel_init,function
lowlevel_init:
- mov r5, pc /* r5 = POS1 + 4 current */
POS1:
+ adr r5, POS1 /* r5 = POS1 run time */
ldr r0, =POS1 /* r0 = POS1 compile */
- ldr r2, _TEXT_BASE
- sub r0, r0, r2 /* r0 = POS1-_TEXT_BASE (POS1 relative) */
sub r5, r5, r0 /* r0 = CONFIG_SYS_TEXT_BASE-1 */
- sub r5, r5, #4 /* r1 = text base - current */
/* memory control configuration 1 */
ldr r0, =SMRDATA
ldr r2, =SMRDATA1
- ldr r1, _TEXT_BASE
- sub r0, r0, r1
- sub r2, r2, r1
add r0, r0, r5
add r2, r2, r5
0:
@@ -149,9 +140,6 @@
ldr r0, =SMRDATA1
ldr r2, =SMRDATA2
- ldr r1, _TEXT_BASE
- sub r0, r0, r1
- sub r2, r2, r1
add r0, r0, r5
add r2, r2, r5
2:
diff --git a/arch/arm/cpu/arm926ejs/mxs/start.S b/arch/arm/cpu/arm926ejs/mxs/start.S
index 5de2bad..34a0fcb 100644
--- a/arch/arm/cpu/arm926ejs/mxs/start.S
+++ b/arch/arm/cpu/arm926ejs/mxs/start.S
@@ -101,32 +101,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#ifdef CONFIG_SPL_TEXT_BASE
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -207,6 +181,5 @@
bx lr
_hang:
- ldr sp, _TEXT_BASE /* switch to abort stack */
1:
bl 1b /* hang and never return */
diff --git a/arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds b/arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
index 80fb9bd..d0b482d 100644
--- a/arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
+++ b/arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
@@ -49,9 +49,14 @@
__bss_end = .;
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
- .dynsym _end : { *(.dynsym) }
+ _image_binary_end = .;
+
+ .dynsym _image_binary_end : { *(.dynsym) }
.dynbss : { *(.dynbss) }
.dynstr : { *(.dynstr*) }
.dynamic : { *(.dynamic*) }
diff --git a/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds b/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
index 76b499d..b6d0f65 100644
--- a/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
+++ b/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
@@ -49,9 +49,14 @@
__bss_end = .;
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
- .dynsym _end : { *(.dynsym) }
+ _image_binary_end = .;
+
+ .dynsym _image_binary_end : { *(.dynsym) }
.dynbss : { *(.dynbss) }
.dynstr : { *(.dynstr*) }
.dynamic : { *(.dynamic*) }
diff --git a/arch/arm/cpu/arm926ejs/start.S b/arch/arm/cpu/arm926ejs/start.S
index 5360f55..0717327 100644
--- a/arch/arm/cpu/arm926ejs/start.S
+++ b/arch/arm/cpu/arm926ejs/start.S
@@ -102,32 +102,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -330,7 +304,6 @@
#ifdef CONFIG_SPL_BUILD
.align 5
do_hang:
- ldr sp, _TEXT_BASE /* switch to abort stack */
1:
bl 1b /* hang and never return */
#else /* !CONFIG_SPL_BUILD */
diff --git a/arch/arm/cpu/arm946es/start.S b/arch/arm/cpu/arm946es/start.S
index e16b088..7d50145 100644
--- a/arch/arm/cpu/arm946es/start.S
+++ b/arch/arm/cpu/arm946es/start.S
@@ -71,32 +71,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
diff --git a/arch/arm/cpu/arm_intcm/start.S b/arch/arm/cpu/arm_intcm/start.S
index 5783df1..7404ea7 100644
--- a/arch/arm/cpu/arm_intcm/start.S
+++ b/arch/arm/cpu/arm_intcm/start.S
@@ -67,32 +67,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
diff --git a/arch/arm/cpu/armv7/Makefile b/arch/arm/cpu/armv7/Makefile
index 0467d00..119ebb3 100644
--- a/arch/arm/cpu/armv7/Makefile
+++ b/arch/arm/cpu/armv7/Makefile
@@ -23,6 +23,7 @@
obj-y += virt-v7.o
endif
+obj-$(CONFIG_KONA) += kona-common/
obj-$(CONFIG_OMAP_COMMON) += omap-common/
obj-$(CONFIG_TEGRA) += tegra-common/
diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c
index c7dad66..2b15a64 100644
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@@ -36,11 +36,15 @@
DECLARE_GLOBAL_DATA_PTR;
-static const struct gpio_bank gpio_bank_am33xx[4] = {
+static const struct gpio_bank gpio_bank_am33xx[] = {
{ (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO2_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO3_BASE, METHOD_GPIO_24XX },
+#ifdef CONFIG_AM43XX
+ { (void *)AM33XX_GPIO4_BASE, METHOD_GPIO_24XX },
+ { (void *)AM33XX_GPIO5_BASE, METHOD_GPIO_24XX },
+#endif
};
const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx;
diff --git a/arch/arm/cpu/armv7/am33xx/clock_am43xx.c b/arch/arm/cpu/armv7/am33xx/clock_am43xx.c
index fb654bb..57f5949 100644
--- a/arch/arm/cpu/armv7/am33xx/clock_am43xx.c
+++ b/arch/arm/cpu/armv7/am33xx/clock_am43xx.c
@@ -94,6 +94,8 @@
&cmper->gpio1clkctrl,
&cmper->gpio2clkctrl,
&cmper->gpio3clkctrl,
+ &cmper->gpio4clkctrl,
+ &cmper->gpio5clkctrl,
&cmper->i2c1clkctrl,
&cmper->emiffwclkctrl,
&cmper->emifclkctrl,
diff --git a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
index ef14f47..9b5a47b 100644
--- a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
+++ b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
@@ -211,11 +211,8 @@
static u32 pll_sigma_delta_val(u32 clkout_dco)
{
u32 sig_val = 0;
- float frac_div;
- frac_div = (float) clkout_dco / 250;
- frac_div = frac_div + 0.90;
- sig_val = (int)frac_div;
+ sig_val = (clkout_dco + 225) / 250;
sig_val = sig_val << 24;
return sig_val;
diff --git a/arch/arm/cpu/armv7/am33xx/u-boot-spl.lds b/arch/arm/cpu/armv7/am33xx/u-boot-spl.lds
index 9302856..b1c28c9 100644
--- a/arch/arm/cpu/armv7/am33xx/u-boot-spl.lds
+++ b/arch/arm/cpu/armv7/am33xx/u-boot-spl.lds
@@ -38,7 +38,11 @@
. = ALIGN(4);
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ } >.sram
.bss :
{
diff --git a/arch/arm/cpu/armv7/bcm281xx/Makefile b/arch/arm/cpu/armv7/bcm281xx/Makefile
new file mode 100644
index 0000000..98f5aa5
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/Makefile
@@ -0,0 +1,11 @@
+#
+# Copyright 2013 Broadcom Corporation.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += reset.o
+obj-y += clk-core.o
+obj-y += clk-bcm281xx.o
+obj-y += clk-sdio.o
+obj-y += clk-bsc.o
diff --git a/arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c b/arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c
new file mode 100644
index 0000000..bc8a170
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c
@@ -0,0 +1,523 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ *
+ * bcm281xx-specific clock tables
+ *
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/sysmap.h>
+#include <asm/kona-common/clk.h>
+#include "clk-core.h"
+
+#define CLOCK_1K 1000
+#define CLOCK_1M (CLOCK_1K * 1000)
+
+/* declare a reference clock */
+#define DECLARE_REF_CLK(clk_name, clk_parent, clk_rate, clk_div) \
+static struct refclk clk_name = { \
+ .clk = { \
+ .name = #clk_name, \
+ .parent = clk_parent, \
+ .rate = clk_rate, \
+ .div = clk_div, \
+ .ops = &ref_clk_ops, \
+ }, \
+}
+
+/*
+ * Reference clocks
+ */
+
+/* Declare a list of reference clocks */
+DECLARE_REF_CLK(ref_crystal, 0, 26 * CLOCK_1M, 1);
+DECLARE_REF_CLK(var_96m, 0, 96 * CLOCK_1M, 1);
+DECLARE_REF_CLK(ref_96m, 0, 96 * CLOCK_1M, 1);
+DECLARE_REF_CLK(ref_312m, 0, 312 * CLOCK_1M, 0);
+DECLARE_REF_CLK(ref_104m, &ref_312m.clk, 104 * CLOCK_1M, 3);
+DECLARE_REF_CLK(ref_52m, &ref_104m.clk, 52 * CLOCK_1M, 2);
+DECLARE_REF_CLK(ref_13m, &ref_52m.clk, 13 * CLOCK_1M, 4);
+DECLARE_REF_CLK(var_312m, 0, 312 * CLOCK_1M, 0);
+DECLARE_REF_CLK(var_104m, &var_312m.clk, 104 * CLOCK_1M, 3);
+DECLARE_REF_CLK(var_52m, &var_104m.clk, 52 * CLOCK_1M, 2);
+DECLARE_REF_CLK(var_13m, &var_52m.clk, 13 * CLOCK_1M, 4);
+
+struct refclk_lkup {
+ struct refclk *procclk;
+ const char *name;
+};
+
+/* Lookup table for string to clk tranlation */
+#define MKSTR(x) {&x, #x}
+static struct refclk_lkup refclk_str_tbl[] = {
+ MKSTR(ref_crystal), MKSTR(var_96m), MKSTR(ref_96m),
+ MKSTR(ref_312m), MKSTR(ref_104m), MKSTR(ref_52m),
+ MKSTR(ref_13m), MKSTR(var_312m), MKSTR(var_104m),
+ MKSTR(var_52m), MKSTR(var_13m),
+};
+
+int refclk_entries = sizeof(refclk_str_tbl)/sizeof(refclk_str_tbl[0]);
+
+/* convert ref clock string to clock structure pointer */
+struct refclk *refclk_str_to_clk(const char *name)
+{
+ int i;
+ struct refclk_lkup *tblp = refclk_str_tbl;
+ for (i = 0; i < refclk_entries; i++, tblp++) {
+ if (!(strcmp(name, tblp->name)))
+ return tblp->procclk;
+ }
+ return NULL;
+}
+
+/* frequency tables indexed by freq_id */
+unsigned long master_axi_freq_tbl[8] = {
+ 26 * CLOCK_1M,
+ 52 * CLOCK_1M,
+ 104 * CLOCK_1M,
+ 156 * CLOCK_1M,
+ 156 * CLOCK_1M,
+ 208 * CLOCK_1M,
+ 312 * CLOCK_1M,
+ 312 * CLOCK_1M
+};
+
+unsigned long master_ahb_freq_tbl[8] = {
+ 26 * CLOCK_1M,
+ 52 * CLOCK_1M,
+ 52 * CLOCK_1M,
+ 52 * CLOCK_1M,
+ 78 * CLOCK_1M,
+ 104 * CLOCK_1M,
+ 104 * CLOCK_1M,
+ 156 * CLOCK_1M
+};
+
+unsigned long slave_axi_freq_tbl[8] = {
+ 26 * CLOCK_1M,
+ 52 * CLOCK_1M,
+ 78 * CLOCK_1M,
+ 104 * CLOCK_1M,
+ 156 * CLOCK_1M,
+ 156 * CLOCK_1M
+};
+
+unsigned long slave_apb_freq_tbl[8] = {
+ 26 * CLOCK_1M,
+ 26 * CLOCK_1M,
+ 39 * CLOCK_1M,
+ 52 * CLOCK_1M,
+ 52 * CLOCK_1M,
+ 78 * CLOCK_1M
+};
+
+static struct bus_clk_data bsc1_apb_data = {
+ .gate = HW_SW_GATE_AUTO(0x0458, 16, 0, 1),
+};
+
+static struct bus_clk_data bsc2_apb_data = {
+ .gate = HW_SW_GATE_AUTO(0x045c, 16, 0, 1),
+};
+
+static struct bus_clk_data bsc3_apb_data = {
+ .gate = HW_SW_GATE_AUTO(0x0484, 16, 0, 1),
+};
+
+/* * Master CCU clocks */
+static struct peri_clk_data sdio1_data = {
+ .gate = HW_SW_GATE(0x0358, 18, 2, 3),
+ .clocks = CLOCKS("ref_crystal",
+ "var_52m",
+ "ref_52m",
+ "var_96m",
+ "ref_96m"),
+ .sel = SELECTOR(0x0a28, 0, 3),
+ .div = DIVIDER(0x0a28, 4, 14),
+ .trig = TRIGGER(0x0afc, 9),
+};
+
+static struct peri_clk_data sdio2_data = {
+ .gate = HW_SW_GATE(0x035c, 18, 2, 3),
+ .clocks = CLOCKS("ref_crystal",
+ "var_52m",
+ "ref_52m",
+ "var_96m",
+ "ref_96m"),
+ .sel = SELECTOR(0x0a2c, 0, 3),
+ .div = DIVIDER(0x0a2c, 4, 14),
+ .trig = TRIGGER(0x0afc, 10),
+};
+
+static struct peri_clk_data sdio3_data = {
+ .gate = HW_SW_GATE(0x0364, 18, 2, 3),
+ .clocks = CLOCKS("ref_crystal",
+ "var_52m",
+ "ref_52m",
+ "var_96m",
+ "ref_96m"),
+ .sel = SELECTOR(0x0a34, 0, 3),
+ .div = DIVIDER(0x0a34, 4, 14),
+ .trig = TRIGGER(0x0afc, 12),
+};
+
+static struct peri_clk_data sdio4_data = {
+ .gate = HW_SW_GATE(0x0360, 18, 2, 3),
+ .clocks = CLOCKS("ref_crystal",
+ "var_52m",
+ "ref_52m",
+ "var_96m",
+ "ref_96m"),
+ .sel = SELECTOR(0x0a30, 0, 3),
+ .div = DIVIDER(0x0a30, 4, 14),
+ .trig = TRIGGER(0x0afc, 11),
+};
+
+static struct peri_clk_data sdio1_sleep_data = {
+ .clocks = CLOCKS("ref_32k"),
+ .gate = SW_ONLY_GATE(0x0358, 20, 4),
+};
+
+static struct peri_clk_data sdio2_sleep_data = {
+ .clocks = CLOCKS("ref_32k"),
+ .gate = SW_ONLY_GATE(0x035c, 20, 4),
+};
+
+static struct peri_clk_data sdio3_sleep_data = {
+ .clocks = CLOCKS("ref_32k"),
+ .gate = SW_ONLY_GATE(0x0364, 20, 4),
+};
+
+static struct peri_clk_data sdio4_sleep_data = {
+ .clocks = CLOCKS("ref_32k"),
+ .gate = SW_ONLY_GATE(0x0360, 20, 4),
+};
+
+static struct bus_clk_data sdio1_ahb_data = {
+ .gate = HW_SW_GATE_AUTO(0x0358, 16, 0, 1),
+};
+
+static struct bus_clk_data sdio2_ahb_data = {
+ .gate = HW_SW_GATE_AUTO(0x035c, 16, 0, 1),
+};
+
+static struct bus_clk_data sdio3_ahb_data = {
+ .gate = HW_SW_GATE_AUTO(0x0364, 16, 0, 1),
+};
+
+static struct bus_clk_data sdio4_ahb_data = {
+ .gate = HW_SW_GATE_AUTO(0x0360, 16, 0, 1),
+};
+
+/* * Slave CCU clocks */
+static struct peri_clk_data bsc1_data = {
+ .gate = HW_SW_GATE(0x0458, 18, 2, 3),
+ .clocks = CLOCKS("ref_crystal",
+ "var_104m",
+ "ref_104m",
+ "var_13m",
+ "ref_13m"),
+ .sel = SELECTOR(0x0a64, 0, 3),
+ .trig = TRIGGER(0x0afc, 23),
+};
+
+static struct peri_clk_data bsc2_data = {
+ .gate = HW_SW_GATE(0x045c, 18, 2, 3),
+ .clocks = CLOCKS("ref_crystal",
+ "var_104m",
+ "ref_104m",
+ "var_13m",
+ "ref_13m"),
+ .sel = SELECTOR(0x0a68, 0, 3),
+ .trig = TRIGGER(0x0afc, 24),
+};
+
+static struct peri_clk_data bsc3_data = {
+ .gate = HW_SW_GATE(0x0484, 18, 2, 3),
+ .clocks = CLOCKS("ref_crystal",
+ "var_104m",
+ "ref_104m",
+ "var_13m",
+ "ref_13m"),
+ .sel = SELECTOR(0x0a84, 0, 3),
+ .trig = TRIGGER(0x0b00, 2),
+};
+
+/*
+ * CCU clocks
+ */
+
+static struct ccu_clock kpm_ccu_clk = {
+ .clk = {
+ .name = "kpm_ccu_clk",
+ .ops = &ccu_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .num_policy_masks = 1,
+ .policy_freq_offset = 0x00000008,
+ .freq_bit_shift = 8,
+ .policy_ctl_offset = 0x0000000c,
+ .policy0_mask_offset = 0x00000010,
+ .policy1_mask_offset = 0x00000014,
+ .policy2_mask_offset = 0x00000018,
+ .policy3_mask_offset = 0x0000001c,
+ .lvm_en_offset = 0x00000034,
+ .freq_id = 2,
+ .freq_tbl = master_axi_freq_tbl,
+};
+
+static struct ccu_clock kps_ccu_clk = {
+ .clk = {
+ .name = "kps_ccu_clk",
+ .ops = &ccu_clk_ops,
+ .ccu_clk_mgr_base = KONA_SLV_CLK_BASE_ADDR,
+ },
+ .num_policy_masks = 2,
+ .policy_freq_offset = 0x00000008,
+ .freq_bit_shift = 8,
+ .policy_ctl_offset = 0x0000000c,
+ .policy0_mask_offset = 0x00000010,
+ .policy1_mask_offset = 0x00000014,
+ .policy2_mask_offset = 0x00000018,
+ .policy3_mask_offset = 0x0000001c,
+ .policy0_mask2_offset = 0x00000048,
+ .policy1_mask2_offset = 0x0000004c,
+ .policy2_mask2_offset = 0x00000050,
+ .policy3_mask2_offset = 0x00000054,
+ .lvm_en_offset = 0x00000034,
+ .freq_id = 2,
+ .freq_tbl = slave_axi_freq_tbl,
+};
+
+/*
+ * Bus clocks
+ */
+
+/* KPM bus clocks */
+static struct bus_clock sdio1_ahb_clk = {
+ .clk = {
+ .name = "sdio1_ahb_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .freq_tbl = master_ahb_freq_tbl,
+ .data = &sdio1_ahb_data,
+};
+
+static struct bus_clock sdio2_ahb_clk = {
+ .clk = {
+ .name = "sdio2_ahb_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .freq_tbl = master_ahb_freq_tbl,
+ .data = &sdio2_ahb_data,
+};
+
+static struct bus_clock sdio3_ahb_clk = {
+ .clk = {
+ .name = "sdio3_ahb_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .freq_tbl = master_ahb_freq_tbl,
+ .data = &sdio3_ahb_data,
+};
+
+static struct bus_clock sdio4_ahb_clk = {
+ .clk = {
+ .name = "sdio4_ahb_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .freq_tbl = master_ahb_freq_tbl,
+ .data = &sdio4_ahb_data,
+};
+
+static struct bus_clock bsc1_apb_clk = {
+ .clk = {
+ .name = "bsc1_apb_clk",
+ .parent = &kps_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_SLV_CLK_BASE_ADDR,
+ },
+ .freq_tbl = slave_apb_freq_tbl,
+ .data = &bsc1_apb_data,
+};
+
+static struct bus_clock bsc2_apb_clk = {
+ .clk = {
+ .name = "bsc2_apb_clk",
+ .parent = &kps_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_SLV_CLK_BASE_ADDR,
+ },
+ .freq_tbl = slave_apb_freq_tbl,
+ .data = &bsc2_apb_data,
+};
+
+static struct bus_clock bsc3_apb_clk = {
+ .clk = {
+ .name = "bsc3_apb_clk",
+ .parent = &kps_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_SLV_CLK_BASE_ADDR,
+ },
+ .freq_tbl = slave_apb_freq_tbl,
+ .data = &bsc3_apb_data,
+};
+
+/* KPM peripheral */
+static struct peri_clock sdio1_clk = {
+ .clk = {
+ .name = "sdio1_clk",
+ .parent = &ref_52m.clk,
+ .ops = &peri_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio1_data,
+};
+
+static struct peri_clock sdio2_clk = {
+ .clk = {
+ .name = "sdio2_clk",
+ .parent = &ref_52m.clk,
+ .ops = &peri_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio2_data,
+};
+
+static struct peri_clock sdio3_clk = {
+ .clk = {
+ .name = "sdio3_clk",
+ .parent = &ref_52m.clk,
+ .ops = &peri_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio3_data,
+};
+
+static struct peri_clock sdio4_clk = {
+ .clk = {
+ .name = "sdio4_clk",
+ .parent = &ref_52m.clk,
+ .ops = &peri_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio4_data,
+};
+
+static struct peri_clock sdio1_sleep_clk = {
+ .clk = {
+ .name = "sdio1_sleep_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio1_sleep_data,
+};
+
+static struct peri_clock sdio2_sleep_clk = {
+ .clk = {
+ .name = "sdio2_sleep_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio2_sleep_data,
+};
+
+static struct peri_clock sdio3_sleep_clk = {
+ .clk = {
+ .name = "sdio3_sleep_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio3_sleep_data,
+};
+
+static struct peri_clock sdio4_sleep_clk = {
+ .clk = {
+ .name = "sdio4_sleep_clk",
+ .parent = &kpm_ccu_clk.clk,
+ .ops = &bus_clk_ops,
+ .ccu_clk_mgr_base = KONA_MST_CLK_BASE_ADDR,
+ },
+ .data = &sdio4_sleep_data,
+};
+
+/* KPS peripheral clock */
+static struct peri_clock bsc1_clk = {
+ .clk = {
+ .name = "bsc1_clk",
+ .parent = &ref_13m.clk,
+ .rate = 13 * CLOCK_1M,
+ .div = 1,
+ .ops = &peri_clk_ops,
+ .ccu_clk_mgr_base = KONA_SLV_CLK_BASE_ADDR,
+ },
+ .data = &bsc1_data,
+};
+
+static struct peri_clock bsc2_clk = {
+ .clk = {
+ .name = "bsc2_clk",
+ .parent = &ref_13m.clk,
+ .rate = 13 * CLOCK_1M,
+ .div = 1,
+ .ops = &peri_clk_ops,
+ .ccu_clk_mgr_base = KONA_SLV_CLK_BASE_ADDR,
+ },
+ .data = &bsc2_data,
+};
+
+static struct peri_clock bsc3_clk = {
+ .clk = {
+ .name = "bsc3_clk",
+ .parent = &ref_13m.clk,
+ .rate = 13 * CLOCK_1M,
+ .div = 1,
+ .ops = &peri_clk_ops,
+ .ccu_clk_mgr_base = KONA_SLV_CLK_BASE_ADDR,
+ },
+ .data = &bsc3_data,
+};
+
+/* public table for registering clocks */
+struct clk_lookup arch_clk_tbl[] = {
+ /* Peripheral clocks */
+ CLK_LK(sdio1),
+ CLK_LK(sdio2),
+ CLK_LK(sdio3),
+ CLK_LK(sdio4),
+ CLK_LK(sdio1_sleep),
+ CLK_LK(sdio2_sleep),
+ CLK_LK(sdio3_sleep),
+ CLK_LK(sdio4_sleep),
+ CLK_LK(bsc1),
+ CLK_LK(bsc2),
+ CLK_LK(bsc3),
+ /* Bus clocks */
+ CLK_LK(sdio1_ahb),
+ CLK_LK(sdio2_ahb),
+ CLK_LK(sdio3_ahb),
+ CLK_LK(sdio4_ahb),
+ CLK_LK(bsc1_apb),
+ CLK_LK(bsc2_apb),
+ CLK_LK(bsc3_apb),
+};
+
+/* public array size */
+unsigned int arch_clk_tbl_array_size = ARRAY_SIZE(arch_clk_tbl);
diff --git a/arch/arm/cpu/armv7/bcm281xx/clk-bsc.c b/arch/arm/cpu/armv7/bcm281xx/clk-bsc.c
new file mode 100644
index 0000000..ba55d0a
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/clk-bsc.c
@@ -0,0 +1,52 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/sysmap.h>
+#include <asm/kona-common/clk.h>
+#include "clk-core.h"
+
+/* Enable appropriate clocks for a BSC/I2C port */
+int clk_bsc_enable(void *base)
+{
+ int ret;
+ char *bscstr, *apbstr;
+
+ switch ((u32) base) {
+ case PMU_BSC_BASE_ADDR:
+ /* PMU clock is always enabled */
+ return 0;
+ case BSC1_BASE_ADDR:
+ bscstr = "bsc1_clk";
+ apbstr = "bsc1_apb_clk";
+ break;
+ case BSC2_BASE_ADDR:
+ bscstr = "bsc2_clk";
+ apbstr = "bsc2_apb_clk";
+ break;
+ case BSC3_BASE_ADDR:
+ bscstr = "bsc3_clk";
+ apbstr = "bsc3_apb_clk";
+ break;
+ default:
+ printf("%s: base 0x%p not found\n", __func__, base);
+ return -EINVAL;
+ }
+
+ /* Note that the bus clock must be enabled first */
+
+ ret = clk_get_and_enable(apbstr);
+ if (ret)
+ return ret;
+
+ ret = clk_get_and_enable(bscstr);
+ if (ret)
+ return ret;
+
+ return 0;
+}
diff --git a/arch/arm/cpu/armv7/bcm281xx/clk-core.c b/arch/arm/cpu/armv7/bcm281xx/clk-core.c
new file mode 100644
index 0000000..d442583
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/clk-core.c
@@ -0,0 +1,513 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ *
+ * bcm281xx architecture clock framework
+ *
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <bitfield.h>
+#include <asm/arch/sysmap.h>
+#include <asm/kona-common/clk.h>
+#include "clk-core.h"
+
+#define CLK_WR_ACCESS_PASSWORD 0x00a5a501
+#define WR_ACCESS_OFFSET 0 /* common to all clock blocks */
+#define POLICY_CTL_GO 1 /* Load and refresh policy masks */
+#define POLICY_CTL_GO_ATL 4 /* Active Load */
+
+/* Helper function */
+int clk_get_and_enable(char *clkstr)
+{
+ int ret = 0;
+ struct clk *c;
+
+ debug("%s: %s\n", __func__, clkstr);
+
+ c = clk_get(clkstr);
+ if (c) {
+ ret = clk_enable(c);
+ if (ret)
+ return ret;
+ } else {
+ printf("%s: Couldn't find %s\n", __func__, clkstr);
+ return -EINVAL;
+ }
+ return ret;
+}
+
+/*
+ * Poll a register in a CCU's address space, returning when the
+ * specified bit in that register's value is set (or clear). Delay
+ * a microsecond after each read of the register. Returns true if
+ * successful, or false if we gave up trying.
+ *
+ * Caller must ensure the CCU lock is held.
+ */
+#define CLK_GATE_DELAY_USEC 2000
+static inline int wait_bit(void *base, u32 offset, u32 bit, bool want)
+{
+ unsigned int tries;
+ u32 bit_mask = 1 << bit;
+
+ for (tries = 0; tries < CLK_GATE_DELAY_USEC; tries++) {
+ u32 val;
+ bool bit_val;
+
+ val = readl(base + offset);
+ bit_val = (val & bit_mask) ? 1 : 0;
+ if (bit_val == want)
+ return 0; /* success */
+ udelay(1);
+ }
+
+ debug("%s: timeout on addr 0x%p, waiting for bit %d to go to %d\n",
+ __func__, base + offset, bit, want);
+
+ return -ETIMEDOUT;
+}
+
+/* Enable a peripheral clock */
+static int peri_clk_enable(struct clk *c, int enable)
+{
+ int ret = 0;
+ u32 reg;
+ struct peri_clock *peri_clk = to_peri_clk(c);
+ struct peri_clk_data *cd = peri_clk->data;
+ struct bcm_clk_gate *gate = &cd->gate;
+ void *base = (void *)c->ccu_clk_mgr_base;
+
+
+ debug("%s: %s\n", __func__, c->name);
+
+ clk_get_rate(c); /* Make sure rate and sel are filled in */
+
+ /* enable access */
+ writel(CLK_WR_ACCESS_PASSWORD, base + WR_ACCESS_OFFSET);
+
+ if (enable) {
+ debug("%s %s set rate %lu div %lu sel %d parent %lu\n",
+ __func__, c->name, c->rate, c->div, c->sel,
+ c->parent->rate);
+
+ /*
+ * clkgate - only software controllable gates are
+ * supported by u-boot which includes all clocks
+ * that matter. This avoids bringing in a lot of extra
+ * complexity as done in the kernel framework.
+ */
+ if (gate_exists(gate)) {
+ reg = readl(base + cd->gate.offset);
+ reg |= (1 << cd->gate.en_bit);
+ writel(reg, base + cd->gate.offset);
+ }
+
+ /* div and pll select */
+ if (divider_exists(&cd->div)) {
+ reg = readl(base + cd->div.offset);
+ bitfield_replace(reg, cd->div.shift, cd->div.width,
+ c->div - 1);
+ writel(reg, base + cd->div.offset);
+ }
+
+ /* frequency selector */
+ if (selector_exists(&cd->sel)) {
+ reg = readl(base + cd->sel.offset);
+ bitfield_replace(reg, cd->sel.shift, cd->sel.width,
+ c->sel);
+ writel(reg, base + cd->sel.offset);
+ }
+
+ /* trigger */
+ if (trigger_exists(&cd->trig)) {
+ writel((1 << cd->trig.bit), base + cd->trig.offset);
+
+ /* wait for trigger status bit to go to 0 */
+ ret = wait_bit(base, cd->trig.offset, cd->trig.bit, 0);
+ if (ret)
+ return ret;
+ }
+
+ /* wait for running (status_bit = 1) */
+ ret = wait_bit(base, cd->gate.offset, cd->gate.status_bit, 1);
+ if (ret)
+ return ret;
+ } else {
+ debug("%s disable clock %s\n", __func__, c->name);
+
+ /* clkgate */
+ reg = readl(base + cd->gate.offset);
+ reg &= ~(1 << cd->gate.en_bit);
+ writel(reg, base + cd->gate.offset);
+
+ /* wait for stop (status_bit = 0) */
+ ret = wait_bit(base, cd->gate.offset, cd->gate.status_bit, 0);
+ }
+
+ /* disable access */
+ writel(0, base + WR_ACCESS_OFFSET);
+
+ return ret;
+}
+
+/* Set the rate of a peripheral clock */
+static int peri_clk_set_rate(struct clk *c, unsigned long rate)
+{
+ int ret = 0;
+ int i;
+ unsigned long diff;
+ unsigned long new_rate = 0, div = 1;
+ struct peri_clock *peri_clk = to_peri_clk(c);
+ struct peri_clk_data *cd = peri_clk->data;
+ const char **clock;
+
+ debug("%s: %s\n", __func__, c->name);
+ diff = rate;
+
+ i = 0;
+ for (clock = cd->clocks; *clock; clock++, i++) {
+ struct refclk *ref = refclk_str_to_clk(*clock);
+ if (!ref) {
+ printf("%s: Lookup of %s failed\n", __func__, *clock);
+ return -EINVAL;
+ }
+
+ /* round to the new rate */
+ div = ref->clk.rate / rate;
+ if (div == 0)
+ div = 1;
+
+ new_rate = ref->clk.rate / div;
+
+ /* get the min diff */
+ if (abs(new_rate - rate) < diff) {
+ diff = abs(new_rate - rate);
+ c->sel = i;
+ c->parent = &ref->clk;
+ c->rate = new_rate;
+ c->div = div;
+ }
+ }
+
+ debug("%s %s set rate %lu div %lu sel %d parent %lu\n", __func__,
+ c->name, c->rate, c->div, c->sel, c->parent->rate);
+ return ret;
+}
+
+/* Get the rate of a peripheral clock */
+static unsigned long peri_clk_get_rate(struct clk *c)
+{
+ struct peri_clock *peri_clk = to_peri_clk(c);
+ struct peri_clk_data *cd = peri_clk->data;
+ void *base = (void *)c->ccu_clk_mgr_base;
+ int div = 1;
+ const char **clock;
+ struct refclk *ref;
+ u32 reg;
+
+ debug("%s: %s\n", __func__, c->name);
+ if (selector_exists(&cd->sel)) {
+ reg = readl(base + cd->sel.offset);
+ c->sel = bitfield_extract(reg, cd->sel.shift, cd->sel.width);
+ } else {
+ /*
+ * For peri clocks that don't have a selector, the single
+ * reference clock will always exist at index 0.
+ */
+ c->sel = 0;
+ }
+
+ if (divider_exists(&cd->div)) {
+ reg = readl(base + cd->div.offset);
+ div = bitfield_extract(reg, cd->div.shift, cd->div.width);
+ div += 1;
+ }
+
+ clock = cd->clocks;
+ ref = refclk_str_to_clk(clock[c->sel]);
+ if (!ref) {
+ printf("%s: Can't lookup %s\n", __func__, clock[c->sel]);
+ return 0;
+ }
+
+ c->parent = &ref->clk;
+ c->div = div;
+ c->rate = c->parent->rate / c->div;
+ debug("%s parent rate %lu div %d sel %d rate %lu\n", __func__,
+ c->parent->rate, div, c->sel, c->rate);
+
+ return c->rate;
+}
+
+/* Peripheral clock operations */
+struct clk_ops peri_clk_ops = {
+ .enable = peri_clk_enable,
+ .set_rate = peri_clk_set_rate,
+ .get_rate = peri_clk_get_rate,
+};
+
+/* Enable a CCU clock */
+static int ccu_clk_enable(struct clk *c, int enable)
+{
+ struct ccu_clock *ccu_clk = to_ccu_clk(c);
+ void *base = (void *)c->ccu_clk_mgr_base;
+ int ret = 0;
+ u32 reg;
+
+ debug("%s: %s\n", __func__, c->name);
+ if (!enable)
+ return -EINVAL; /* CCU clock cannot shutdown */
+
+ /* enable access */
+ writel(CLK_WR_ACCESS_PASSWORD, base + WR_ACCESS_OFFSET);
+
+ /* config enable for policy engine */
+ writel(1, base + ccu_clk->lvm_en_offset);
+
+ /* wait for bit to go to 0 */
+ ret = wait_bit(base, ccu_clk->lvm_en_offset, 0, 0);
+ if (ret)
+ return ret;
+
+ /* freq ID */
+ if (!ccu_clk->freq_bit_shift)
+ ccu_clk->freq_bit_shift = 8;
+
+ /* Set frequency id for each of the 4 policies */
+ reg = ccu_clk->freq_id |
+ (ccu_clk->freq_id << (ccu_clk->freq_bit_shift)) |
+ (ccu_clk->freq_id << (ccu_clk->freq_bit_shift * 2)) |
+ (ccu_clk->freq_id << (ccu_clk->freq_bit_shift * 3));
+ writel(reg, base + ccu_clk->policy_freq_offset);
+
+ /* enable all clock mask */
+ writel(0x7fffffff, base + ccu_clk->policy0_mask_offset);
+ writel(0x7fffffff, base + ccu_clk->policy1_mask_offset);
+ writel(0x7fffffff, base + ccu_clk->policy2_mask_offset);
+ writel(0x7fffffff, base + ccu_clk->policy3_mask_offset);
+
+ if (ccu_clk->num_policy_masks == 2) {
+ writel(0x7fffffff, base + ccu_clk->policy0_mask2_offset);
+ writel(0x7fffffff, base + ccu_clk->policy1_mask2_offset);
+ writel(0x7fffffff, base + ccu_clk->policy2_mask2_offset);
+ writel(0x7fffffff, base + ccu_clk->policy3_mask2_offset);
+ }
+
+ /* start policy engine */
+ reg = readl(base + ccu_clk->policy_ctl_offset);
+ reg |= (POLICY_CTL_GO + POLICY_CTL_GO_ATL);
+ writel(reg, base + ccu_clk->policy_ctl_offset);
+
+ /* wait till started */
+ ret = wait_bit(base, ccu_clk->policy_ctl_offset, 0, 0);
+ if (ret)
+ return ret;
+
+ /* disable access */
+ writel(0, base + WR_ACCESS_OFFSET);
+
+ return ret;
+}
+
+/* Get the CCU clock rate */
+static unsigned long ccu_clk_get_rate(struct clk *c)
+{
+ struct ccu_clock *ccu_clk = to_ccu_clk(c);
+ debug("%s: %s\n", __func__, c->name);
+ c->rate = ccu_clk->freq_tbl[ccu_clk->freq_id];
+ return c->rate;
+}
+
+/* CCU clock operations */
+struct clk_ops ccu_clk_ops = {
+ .enable = ccu_clk_enable,
+ .get_rate = ccu_clk_get_rate,
+};
+
+/* Enable a bus clock */
+static int bus_clk_enable(struct clk *c, int enable)
+{
+ struct bus_clock *bus_clk = to_bus_clk(c);
+ struct bus_clk_data *cd = bus_clk->data;
+ void *base = (void *)c->ccu_clk_mgr_base;
+ int ret = 0;
+ u32 reg;
+
+ debug("%s: %s\n", __func__, c->name);
+ /* enable access */
+ writel(CLK_WR_ACCESS_PASSWORD, base + WR_ACCESS_OFFSET);
+
+ /* enable gating */
+ reg = readl(base + cd->gate.offset);
+ if (!!(reg & (1 << cd->gate.status_bit)) == !!enable)
+ debug("%s already %s\n", c->name,
+ enable ? "enabled" : "disabled");
+ else {
+ int want = (enable) ? 1 : 0;
+ reg |= (1 << cd->gate.hw_sw_sel_bit);
+
+ if (enable)
+ reg |= (1 << cd->gate.en_bit);
+ else
+ reg &= ~(1 << cd->gate.en_bit);
+
+ writel(reg, base + cd->gate.offset);
+ ret = wait_bit(base, cd->gate.offset, cd->gate.status_bit,
+ want);
+ if (ret)
+ return ret;
+ }
+
+ /* disable access */
+ writel(0, base + WR_ACCESS_OFFSET);
+
+ return ret;
+}
+
+/* Get the rate of a bus clock */
+static unsigned long bus_clk_get_rate(struct clk *c)
+{
+ struct bus_clock *bus_clk = to_bus_clk(c);
+ struct ccu_clock *ccu_clk;
+
+ debug("%s: %s\n", __func__, c->name);
+ ccu_clk = to_ccu_clk(c->parent);
+
+ c->rate = bus_clk->freq_tbl[ccu_clk->freq_id];
+ c->div = ccu_clk->freq_tbl[ccu_clk->freq_id] / c->rate;
+ return c->rate;
+}
+
+/* Bus clock operations */
+struct clk_ops bus_clk_ops = {
+ .enable = bus_clk_enable,
+ .get_rate = bus_clk_get_rate,
+};
+
+/* Enable a reference clock */
+static int ref_clk_enable(struct clk *c, int enable)
+{
+ debug("%s: %s\n", __func__, c->name);
+ return 0;
+}
+
+/* Reference clock operations */
+struct clk_ops ref_clk_ops = {
+ .enable = ref_clk_enable,
+};
+
+/*
+ * clk.h implementation follows
+ */
+
+/* Initialize the clock framework */
+int clk_init(void)
+{
+ debug("%s:\n", __func__);
+ return 0;
+}
+
+/* Get a clock handle, give a name string */
+struct clk *clk_get(const char *con_id)
+{
+ int i;
+ struct clk_lookup *clk_tblp;
+
+ debug("%s: %s\n", __func__, con_id);
+
+ clk_tblp = arch_clk_tbl;
+ for (i = 0; i < arch_clk_tbl_array_size; i++, clk_tblp++) {
+ if (clk_tblp->con_id) {
+ if (!con_id || strcmp(clk_tblp->con_id, con_id))
+ continue;
+ return clk_tblp->clk;
+ }
+ }
+ return NULL;
+}
+
+/* Enable a clock */
+int clk_enable(struct clk *c)
+{
+ int ret = 0;
+
+ debug("%s: %s\n", __func__, c->name);
+ if (!c->ops || !c->ops->enable)
+ return -1;
+
+ /* enable parent clock first */
+ if (c->parent)
+ ret = clk_enable(c->parent);
+
+ if (ret)
+ return ret;
+
+ if (!c->use_cnt) {
+ c->use_cnt++;
+ ret = c->ops->enable(c, 1);
+ }
+
+ return ret;
+}
+
+/* Disable a clock */
+void clk_disable(struct clk *c)
+{
+ debug("%s: %s\n", __func__, c->name);
+ if (!c->ops || !c->ops->enable)
+ return;
+
+ if (c->use_cnt) {
+ c->use_cnt--;
+ c->ops->enable(c, 0);
+ }
+
+ /* disable parent */
+ if (c->parent)
+ clk_disable(c->parent);
+}
+
+/* Get the clock rate */
+unsigned long clk_get_rate(struct clk *c)
+{
+ unsigned long rate;
+
+ debug("%s: %s\n", __func__, c->name);
+ if (!c || !c->ops || !c->ops->get_rate)
+ return 0;
+
+ rate = c->ops->get_rate(c);
+ debug("%s: rate = %ld\n", __func__, rate);
+ return rate;
+}
+
+/* Set the clock rate */
+int clk_set_rate(struct clk *c, unsigned long rate)
+{
+ int ret;
+
+ debug("%s: %s rate=%ld\n", __func__, c->name, rate);
+ if (!c || !c->ops || !c->ops->set_rate)
+ return -EINVAL;
+
+ if (c->use_cnt)
+ return -EINVAL;
+
+ ret = c->ops->set_rate(c, rate);
+
+ return ret;
+}
+
+/* Not required for this arch */
+/*
+long clk_round_rate(struct clk *clk, unsigned long rate);
+int clk_set_parent(struct clk *clk, struct clk *parent);
+struct clk *clk_get_parent(struct clk *clk);
+*/
diff --git a/arch/arm/cpu/armv7/bcm281xx/clk-core.h b/arch/arm/cpu/armv7/bcm281xx/clk-core.h
new file mode 100644
index 0000000..882a297
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/clk-core.h
@@ -0,0 +1,495 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <linux/stddef.h>
+
+#ifdef CONFIG_CLK_DEBUG
+#undef writel
+#undef readl
+static inline void writel(u32 val, void *addr)
+{
+ printf("Write [0x%p] = 0x%08x\n", addr, val);
+ *(u32 *)addr = val;
+}
+
+static inline u32 readl(void *addr)
+{
+ u32 val = *(u32 *)addr;
+ printf("Read [0x%p] = 0x%08x\n", addr, val);
+ return val;
+}
+#endif
+
+struct clk;
+
+struct clk_lookup {
+ const char *dev_id;
+ const char *con_id;
+ struct clk *clk;
+};
+
+extern struct clk_lookup arch_clk_tbl[];
+extern unsigned int arch_clk_tbl_array_size;
+
+/**
+ * struct clk_ops - standard clock operations
+ * @enable: enable/disable clock, see clk_enable() and clk_disable()
+ * @set_rate: set the clock rate, see clk_set_rate().
+ * @get_rate: get the clock rate, see clk_get_rate().
+ * @round_rate: round a given clock rate, see clk_round_rate().
+ * @set_parent: set the clock's parent, see clk_set_parent().
+ *
+ * Group the common clock implementations together so that we
+ * don't have to keep setting the same fiels again. We leave
+ * enable in struct clk.
+ *
+ */
+struct clk_ops {
+ int (*enable) (struct clk *c, int enable);
+ int (*set_rate) (struct clk *c, unsigned long rate);
+ unsigned long (*get_rate) (struct clk *c);
+ unsigned long (*round_rate) (struct clk *c, unsigned long rate);
+ int (*set_parent) (struct clk *c, struct clk *parent);
+};
+
+struct clk {
+ struct clk *parent;
+ const char *name;
+ int use_cnt;
+ unsigned long rate; /* in HZ */
+
+ /* programmable divider. 0 means fixed ratio to parent clock */
+ unsigned long div;
+
+ struct clk_src *src;
+ struct clk_ops *ops;
+
+ unsigned long ccu_clk_mgr_base;
+ int sel;
+};
+
+struct refclk *refclk_str_to_clk(const char *name);
+
+#define U8_MAX ((u8)~0U)
+#define U32_MAX ((u32)~0U)
+#define U64_MAX ((u64)~0U)
+
+/* The common clock framework uses u8 to represent a parent index */
+#define PARENT_COUNT_MAX ((u32)U8_MAX)
+
+#define BAD_CLK_INDEX U8_MAX /* Can't ever be valid */
+#define BAD_CLK_NAME ((const char *)-1)
+
+#define BAD_SCALED_DIV_VALUE U64_MAX
+
+/*
+ * Utility macros for object flag management. If possible, flags
+ * should be defined such that 0 is the desired default value.
+ */
+#define FLAG(type, flag) BCM_CLK_ ## type ## _FLAGS_ ## flag
+#define FLAG_SET(obj, type, flag) ((obj)->flags |= FLAG(type, flag))
+#define FLAG_CLEAR(obj, type, flag) ((obj)->flags &= ~(FLAG(type, flag)))
+#define FLAG_FLIP(obj, type, flag) ((obj)->flags ^= FLAG(type, flag))
+#define FLAG_TEST(obj, type, flag) (!!((obj)->flags & FLAG(type, flag)))
+
+/* Clock field state tests */
+
+#define gate_exists(gate) FLAG_TEST(gate, GATE, EXISTS)
+#define gate_is_enabled(gate) FLAG_TEST(gate, GATE, ENABLED)
+#define gate_is_hw_controllable(gate) FLAG_TEST(gate, GATE, HW)
+#define gate_is_sw_controllable(gate) FLAG_TEST(gate, GATE, SW)
+#define gate_is_sw_managed(gate) FLAG_TEST(gate, GATE, SW_MANAGED)
+#define gate_is_no_disable(gate) FLAG_TEST(gate, GATE, NO_DISABLE)
+
+#define gate_flip_enabled(gate) FLAG_FLIP(gate, GATE, ENABLED)
+
+#define divider_exists(div) FLAG_TEST(div, DIV, EXISTS)
+#define divider_is_fixed(div) FLAG_TEST(div, DIV, FIXED)
+#define divider_has_fraction(div) (!divider_is_fixed(div) && \
+ (div)->frac_width > 0)
+
+#define selector_exists(sel) ((sel)->width != 0)
+#define trigger_exists(trig) FLAG_TEST(trig, TRIG, EXISTS)
+
+/* Clock type, used to tell common block what it's part of */
+enum bcm_clk_type {
+ bcm_clk_none, /* undefined clock type */
+ bcm_clk_bus,
+ bcm_clk_core,
+ bcm_clk_peri
+};
+
+/*
+ * Gating control and status is managed by a 32-bit gate register.
+ *
+ * There are several types of gating available:
+ * - (no gate)
+ * A clock with no gate is assumed to be always enabled.
+ * - hardware-only gating (auto-gating)
+ * Enabling or disabling clocks with this type of gate is
+ * managed automatically by the hardware. Such clocks can be
+ * considered by the software to be enabled. The current status
+ * of auto-gated clocks can be read from the gate status bit.
+ * - software-only gating
+ * Auto-gating is not available for this type of clock.
+ * Instead, software manages whether it's enabled by setting or
+ * clearing the enable bit. The current gate status of a gate
+ * under software control can be read from the gate status bit.
+ * To ensure a change to the gating status is complete, the
+ * status bit can be polled to verify that the gate has entered
+ * the desired state.
+ * - selectable hardware or software gating
+ * Gating for this type of clock can be configured to be either
+ * under software or hardware control. Which type is in use is
+ * determined by the hw_sw_sel bit of the gate register.
+ */
+struct bcm_clk_gate {
+ u32 offset; /* gate register offset */
+ u32 status_bit; /* 0: gate is disabled; 0: gatge is enabled */
+ u32 en_bit; /* 0: disable; 1: enable */
+ u32 hw_sw_sel_bit; /* 0: hardware gating; 1: software gating */
+ u32 flags; /* BCM_CLK_GATE_FLAGS_* below */
+};
+
+/*
+ * Gate flags:
+ * HW means this gate can be auto-gated
+ * SW means the state of this gate can be software controlled
+ * NO_DISABLE means this gate is (only) enabled if under software control
+ * SW_MANAGED means the status of this gate is under software control
+ * ENABLED means this software-managed gate is *supposed* to be enabled
+ */
+#define BCM_CLK_GATE_FLAGS_EXISTS ((u32)1 << 0) /* Gate is valid */
+#define BCM_CLK_GATE_FLAGS_HW ((u32)1 << 1) /* Can auto-gate */
+#define BCM_CLK_GATE_FLAGS_SW ((u32)1 << 2) /* Software control */
+#define BCM_CLK_GATE_FLAGS_NO_DISABLE ((u32)1 << 3) /* HW or enabled */
+#define BCM_CLK_GATE_FLAGS_SW_MANAGED ((u32)1 << 4) /* SW now in control */
+#define BCM_CLK_GATE_FLAGS_ENABLED ((u32)1 << 5) /* If SW_MANAGED */
+
+/*
+ * Gate initialization macros.
+ *
+ * Any gate initially under software control will be enabled.
+ */
+
+/* A hardware/software gate initially under software control */
+#define HW_SW_GATE(_offset, _status_bit, _en_bit, _hw_sw_sel_bit) \
+ { \
+ .offset = (_offset), \
+ .status_bit = (_status_bit), \
+ .en_bit = (_en_bit), \
+ .hw_sw_sel_bit = (_hw_sw_sel_bit), \
+ .flags = FLAG(GATE, HW)|FLAG(GATE, SW)| \
+ FLAG(GATE, SW_MANAGED)|FLAG(GATE, ENABLED)| \
+ FLAG(GATE, EXISTS), \
+ }
+
+/* A hardware/software gate initially under hardware control */
+#define HW_SW_GATE_AUTO(_offset, _status_bit, _en_bit, _hw_sw_sel_bit) \
+ { \
+ .offset = (_offset), \
+ .status_bit = (_status_bit), \
+ .en_bit = (_en_bit), \
+ .hw_sw_sel_bit = (_hw_sw_sel_bit), \
+ .flags = FLAG(GATE, HW)|FLAG(GATE, SW)| \
+ FLAG(GATE, EXISTS), \
+ }
+
+/* A hardware-or-enabled gate (enabled if not under hardware control) */
+#define HW_ENABLE_GATE(_offset, _status_bit, _en_bit, _hw_sw_sel_bit) \
+ { \
+ .offset = (_offset), \
+ .status_bit = (_status_bit), \
+ .en_bit = (_en_bit), \
+ .hw_sw_sel_bit = (_hw_sw_sel_bit), \
+ .flags = FLAG(GATE, HW)|FLAG(GATE, SW)| \
+ FLAG(GATE, NO_DISABLE)|FLAG(GATE, EXISTS), \
+ }
+
+/* A software-only gate */
+#define SW_ONLY_GATE(_offset, _status_bit, _en_bit) \
+ { \
+ .offset = (_offset), \
+ .status_bit = (_status_bit), \
+ .en_bit = (_en_bit), \
+ .flags = FLAG(GATE, SW)|FLAG(GATE, SW_MANAGED)| \
+ FLAG(GATE, ENABLED)|FLAG(GATE, EXISTS), \
+ }
+
+/* A hardware-only gate */
+#define HW_ONLY_GATE(_offset, _status_bit) \
+ { \
+ .offset = (_offset), \
+ .status_bit = (_status_bit), \
+ .flags = FLAG(GATE, HW)|FLAG(GATE, EXISTS), \
+ }
+
+/*
+ * Each clock can have zero, one, or two dividers which change the
+ * output rate of the clock. Each divider can be either fixed or
+ * variable. If there are two dividers, they are the "pre-divider"
+ * and the "regular" or "downstream" divider. If there is only one,
+ * there is no pre-divider.
+ *
+ * A fixed divider is any non-zero (positive) value, and it
+ * indicates how the input rate is affected by the divider.
+ *
+ * The value of a variable divider is maintained in a sub-field of a
+ * 32-bit divider register. The position of the field in the
+ * register is defined by its offset and width. The value recorded
+ * in this field is always 1 less than the value it represents.
+ *
+ * In addition, a variable divider can indicate that some subset
+ * of its bits represent a "fractional" part of the divider. Such
+ * bits comprise the low-order portion of the divider field, and can
+ * be viewed as representing the portion of the divider that lies to
+ * the right of the decimal point. Most variable dividers have zero
+ * fractional bits. Variable dividers with non-zero fraction width
+ * still record a value 1 less than the value they represent; the
+ * added 1 does *not* affect the low-order bit in this case, it
+ * affects the bits above the fractional part only. (Often in this
+ * code a divider field value is distinguished from the value it
+ * represents by referring to the latter as a "divisor".)
+ *
+ * In order to avoid dealing with fractions, divider arithmetic is
+ * performed using "scaled" values. A scaled value is one that's
+ * been left-shifted by the fractional width of a divider. Dividing
+ * a scaled value by a scaled divisor produces the desired quotient
+ * without loss of precision and without any other special handling
+ * for fractions.
+ *
+ * The recorded value of a variable divider can be modified. To
+ * modify either divider (or both), a clock must be enabled (i.e.,
+ * using its gate). In addition, a trigger register (described
+ * below) must be used to commit the change, and polled to verify
+ * the change is complete.
+ */
+struct bcm_clk_div {
+ union {
+ struct { /* variable divider */
+ u32 offset; /* divider register offset */
+ u32 shift; /* field shift */
+ u32 width; /* field width */
+ u32 frac_width; /* field fraction width */
+
+ u64 scaled_div; /* scaled divider value */
+ };
+ u32 fixed; /* non-zero fixed divider value */
+ };
+ u32 flags; /* BCM_CLK_DIV_FLAGS_* below */
+};
+
+/*
+ * Divider flags:
+ * EXISTS means this divider exists
+ * FIXED means it is a fixed-rate divider
+ */
+#define BCM_CLK_DIV_FLAGS_EXISTS ((u32)1 << 0) /* Divider is valid */
+#define BCM_CLK_DIV_FLAGS_FIXED ((u32)1 << 1) /* Fixed-value */
+
+/* Divider initialization macros */
+
+/* A fixed (non-zero) divider */
+#define FIXED_DIVIDER(_value) \
+ { \
+ .fixed = (_value), \
+ .flags = FLAG(DIV, EXISTS)|FLAG(DIV, FIXED), \
+ }
+
+/* A divider with an integral divisor */
+#define DIVIDER(_offset, _shift, _width) \
+ { \
+ .offset = (_offset), \
+ .shift = (_shift), \
+ .width = (_width), \
+ .scaled_div = BAD_SCALED_DIV_VALUE, \
+ .flags = FLAG(DIV, EXISTS), \
+ }
+
+/* A divider whose divisor has an integer and fractional part */
+#define FRAC_DIVIDER(_offset, _shift, _width, _frac_width) \
+ { \
+ .offset = (_offset), \
+ .shift = (_shift), \
+ .width = (_width), \
+ .frac_width = (_frac_width), \
+ .scaled_div = BAD_SCALED_DIV_VALUE, \
+ .flags = FLAG(DIV, EXISTS), \
+ }
+
+/*
+ * Clocks may have multiple "parent" clocks. If there is more than
+ * one, a selector must be specified to define which of the parent
+ * clocks is currently in use. The selected clock is indicated in a
+ * sub-field of a 32-bit selector register. The range of
+ * representable selector values typically exceeds the number of
+ * available parent clocks. Occasionally the reset value of a
+ * selector field is explicitly set to a (specific) value that does
+ * not correspond to a defined input clock.
+ *
+ * We register all known parent clocks with the common clock code
+ * using a packed array (i.e., no empty slots) of (parent) clock
+ * names, and refer to them later using indexes into that array.
+ * We maintain an array of selector values indexed by common clock
+ * index values in order to map between these common clock indexes
+ * and the selector values used by the hardware.
+ *
+ * Like dividers, a selector can be modified, but to do so a clock
+ * must be enabled, and a trigger must be used to commit the change.
+ */
+struct bcm_clk_sel {
+ u32 offset; /* selector register offset */
+ u32 shift; /* field shift */
+ u32 width; /* field width */
+
+ u32 parent_count; /* number of entries in parent_sel[] */
+ u32 *parent_sel; /* array of parent selector values */
+ u8 clk_index; /* current selected index in parent_sel[] */
+};
+
+/* Selector initialization macro */
+#define SELECTOR(_offset, _shift, _width) \
+ { \
+ .offset = (_offset), \
+ .shift = (_shift), \
+ .width = (_width), \
+ .clk_index = BAD_CLK_INDEX, \
+ }
+
+/*
+ * Making changes to a variable divider or a selector for a clock
+ * requires the use of a trigger. A trigger is defined by a single
+ * bit within a register. To signal a change, a 1 is written into
+ * that bit. To determine when the change has been completed, that
+ * trigger bit is polled; the read value will be 1 while the change
+ * is in progress, and 0 when it is complete.
+ *
+ * Occasionally a clock will have more than one trigger. In this
+ * case, the "pre-trigger" will be used when changing a clock's
+ * selector and/or its pre-divider.
+ */
+struct bcm_clk_trig {
+ u32 offset; /* trigger register offset */
+ u32 bit; /* trigger bit */
+ u32 flags; /* BCM_CLK_TRIG_FLAGS_* below */
+};
+
+/*
+ * Trigger flags:
+ * EXISTS means this trigger exists
+ */
+#define BCM_CLK_TRIG_FLAGS_EXISTS ((u32)1 << 0) /* Trigger is valid */
+
+/* Trigger initialization macro */
+#define TRIGGER(_offset, _bit) \
+ { \
+ .offset = (_offset), \
+ .bit = (_bit), \
+ .flags = FLAG(TRIG, EXISTS), \
+ }
+
+struct bus_clk_data {
+ struct bcm_clk_gate gate;
+};
+
+struct core_clk_data {
+ struct bcm_clk_gate gate;
+};
+
+struct peri_clk_data {
+ struct bcm_clk_gate gate;
+ struct bcm_clk_trig pre_trig;
+ struct bcm_clk_div pre_div;
+ struct bcm_clk_trig trig;
+ struct bcm_clk_div div;
+ struct bcm_clk_sel sel;
+ const char *clocks[]; /* must be last; use CLOCKS() to declare */
+};
+#define CLOCKS(...) { __VA_ARGS__, NULL, }
+#define NO_CLOCKS { NULL, } /* Must use of no parent clocks */
+
+struct refclk {
+ struct clk clk;
+};
+
+struct peri_clock {
+ struct clk clk;
+ struct peri_clk_data *data;
+};
+
+struct ccu_clock {
+ struct clk clk;
+
+ int num_policy_masks;
+ unsigned long policy_freq_offset;
+ int freq_bit_shift; /* 8 for most CCUs */
+ unsigned long policy_ctl_offset;
+ unsigned long policy0_mask_offset;
+ unsigned long policy1_mask_offset;
+ unsigned long policy2_mask_offset;
+ unsigned long policy3_mask_offset;
+ unsigned long policy0_mask2_offset;
+ unsigned long policy1_mask2_offset;
+ unsigned long policy2_mask2_offset;
+ unsigned long policy3_mask2_offset;
+ unsigned long lvm_en_offset;
+
+ int freq_id;
+ unsigned long *freq_tbl;
+};
+
+struct bus_clock {
+ struct clk clk;
+ struct bus_clk_data *data;
+ unsigned long *freq_tbl;
+};
+
+struct ref_clock {
+ struct clk clk;
+};
+
+static inline int is_same_clock(struct clk *a, struct clk *b)
+{
+ return (a == b);
+}
+
+#define to_clk(p) (&((p)->clk))
+#define name_to_clk(name) (&((name##_clk).clk))
+/* declare a struct clk_lookup */
+#define CLK_LK(name) \
+{.con_id = __stringify(name##_clk), .clk = name_to_clk(name),}
+
+static inline struct refclk *to_refclk(struct clk *clock)
+{
+ return container_of(clock, struct refclk, clk);
+}
+
+static inline struct peri_clock *to_peri_clk(struct clk *clock)
+{
+ return container_of(clock, struct peri_clock, clk);
+}
+
+static inline struct ccu_clock *to_ccu_clk(struct clk *clock)
+{
+ return container_of(clock, struct ccu_clock, clk);
+}
+
+static inline struct bus_clock *to_bus_clk(struct clk *clock)
+{
+ return container_of(clock, struct bus_clock, clk);
+}
+
+static inline struct ref_clock *to_ref_clk(struct clk *clock)
+{
+ return container_of(clock, struct ref_clock, clk);
+}
+
+extern struct clk_ops peri_clk_ops;
+extern struct clk_ops ccu_clk_ops;
+extern struct clk_ops bus_clk_ops;
+extern struct clk_ops ref_clk_ops;
+
+extern int clk_get_and_enable(char *clkstr);
diff --git a/arch/arm/cpu/armv7/bcm281xx/clk-sdio.c b/arch/arm/cpu/armv7/bcm281xx/clk-sdio.c
new file mode 100644
index 0000000..49badcb
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/clk-sdio.c
@@ -0,0 +1,73 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/sysmap.h>
+#include <asm/kona-common/clk.h>
+#include "clk-core.h"
+
+/* Enable appropriate clocks for an SDIO port */
+int clk_sdio_enable(void *base, u32 rate, u32 *actual_ratep)
+{
+ int ret;
+ struct clk *c;
+
+ char *clkstr;
+ char *slpstr;
+ char *ahbstr;
+
+ switch ((u32) base) {
+ case CONFIG_SYS_SDIO_BASE0:
+ clkstr = CONFIG_SYS_SDIO0 "_clk";
+ ahbstr = CONFIG_SYS_SDIO0 "_ahb_clk";
+ slpstr = CONFIG_SYS_SDIO0 "_sleep_clk";
+ break;
+ case CONFIG_SYS_SDIO_BASE1:
+ clkstr = CONFIG_SYS_SDIO1 "_clk";
+ ahbstr = CONFIG_SYS_SDIO1 "_ahb_clk";
+ slpstr = CONFIG_SYS_SDIO1 "_sleep_clk";
+ break;
+ case CONFIG_SYS_SDIO_BASE2:
+ clkstr = CONFIG_SYS_SDIO2 "_clk";
+ ahbstr = CONFIG_SYS_SDIO2 "_ahb_clk";
+ slpstr = CONFIG_SYS_SDIO2 "_sleep_clk";
+ break;
+ case CONFIG_SYS_SDIO_BASE3:
+ clkstr = CONFIG_SYS_SDIO3 "_clk";
+ ahbstr = CONFIG_SYS_SDIO3 "_ahb_clk";
+ slpstr = CONFIG_SYS_SDIO3 "_sleep_clk";
+ break;
+ default:
+ printf("%s: base 0x%p not found\n", __func__, base);
+ return -EINVAL;
+ }
+
+ ret = clk_get_and_enable(ahbstr);
+ if (ret)
+ return ret;
+
+ ret = clk_get_and_enable(slpstr);
+ if (ret)
+ return ret;
+
+ c = clk_get(clkstr);
+ if (c) {
+ ret = clk_set_rate(c, rate);
+ if (ret)
+ return ret;
+
+ ret = clk_enable(c);
+ if (ret)
+ return ret;
+ } else {
+ printf("%s: Couldn't find %s\n", __func__, clkstr);
+ return -EINVAL;
+ }
+ *actual_ratep = rate;
+ return 0;
+}
diff --git a/arch/arm/cpu/armv7/bcm281xx/reset.c b/arch/arm/cpu/armv7/bcm281xx/reset.c
new file mode 100644
index 0000000..3beb0ed
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/reset.c
@@ -0,0 +1,27 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sysmap.h>
+
+#define EN_MASK 0x08000000 /* Enable timer */
+#define SRSTEN_MASK 0x04000000 /* Enable soft reset */
+#define CLKS_SHIFT 20 /* Clock period shift */
+#define LD_SHIFT 0 /* Reload value shift */
+
+void reset_cpu(ulong ignored)
+{
+ /*
+ * Set WD enable, RST enable,
+ * 3.9 msec clock period (8), reload value (8*3.9ms)
+ */
+ u32 reg = EN_MASK + SRSTEN_MASK + (8 << CLKS_SHIFT) + (8 << LD_SHIFT);
+ writel(reg, SECWD2_BASE_ADDR);
+
+ while (1)
+ ; /* loop forever till reset */
+}
diff --git a/arch/arm/cpu/armv7/config.mk b/arch/arm/cpu/armv7/config.mk
index 247b7a5..6c82c3b 100644
--- a/arch/arm/cpu/armv7/config.mk
+++ b/arch/arm/cpu/armv7/config.mk
@@ -10,6 +10,9 @@
PF_CPPFLAGS_ARMV7 := $(call cc-option, -march=armv7-a, -march=armv5)
PLATFORM_CPPFLAGS += $(PF_CPPFLAGS_ARMV7)
-# SEE README.arm-unaligned-accesses
+# On supported platforms we set the bit which causes us to trap on unaligned
+# memory access. This is the opposite of what the compiler expects to be
+# the default so we must pass in -mno-unaligned-access so that it is aware
+# of our decision.
PF_NO_UNALIGNED := $(call cc-option, -mno-unaligned-access,)
-PLATFORM_NO_UNALIGNED := $(PF_NO_UNALIGNED)
+PLATFORM_CPPFLAGS += $(PF_NO_UNALIGNED)
diff --git a/arch/arm/cpu/armv7/kona-common/Makefile b/arch/arm/cpu/armv7/kona-common/Makefile
new file mode 100644
index 0000000..da225cb
--- /dev/null
+++ b/arch/arm/cpu/armv7/kona-common/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright 2013 Broadcom Corporation.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += s_init.o
+obj-y += hwinit-common.o
+obj-y += clk-stubs.o
diff --git a/arch/arm/cpu/armv7/kona-common/clk-stubs.c b/arch/arm/cpu/armv7/kona-common/clk-stubs.c
new file mode 100644
index 0000000..338e0e4
--- /dev/null
+++ b/arch/arm/cpu/armv7/kona-common/clk-stubs.c
@@ -0,0 +1,21 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+
+/*
+ * These weak functions are available to kona architectures that don't
+ * require clock enables from the driver code.
+ */
+int __weak clk_sdio_enable(void *base, u32 rate, u32 *actual_ratep)
+{
+ return 0;
+}
+
+int __weak clk_bsc_enable(void *base, u32 rate, u32 *actual_ratep)
+{
+ return 0;
+}
diff --git a/arch/arm/cpu/armv7/kona-common/hwinit-common.c b/arch/arm/cpu/armv7/kona-common/hwinit-common.c
new file mode 100644
index 0000000..f8b1e06
--- /dev/null
+++ b/arch/arm/cpu/armv7/kona-common/hwinit-common.c
@@ -0,0 +1,16 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/sizes.h>
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+void enable_caches(void)
+{
+ /* Enable D-cache. I-cache is already enabled in start.S */
+ dcache_enable();
+}
+#endif
diff --git a/arch/arm/cpu/armv7/kona-common/s_init.c b/arch/arm/cpu/armv7/kona-common/s_init.c
new file mode 100644
index 0000000..6066a73
--- /dev/null
+++ b/arch/arm/cpu/armv7/kona-common/s_init.c
@@ -0,0 +1,12 @@
+/*
+ * Copyright 2014 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * Early system init. Currently empty.
+ */
+void s_init(void)
+{
+}
diff --git a/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds b/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
index 02aa129..745603d 100644
--- a/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
+++ b/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
@@ -39,7 +39,11 @@
. = ALIGN(4);
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ }
.bss :
{
diff --git a/arch/arm/cpu/armv7/omap3/lowlevel_init.S b/arch/arm/cpu/armv7/omap3/lowlevel_init.S
index 6f7261b..78577b1 100644
--- a/arch/arm/cpu/armv7/omap3/lowlevel_init.S
+++ b/arch/arm/cpu/armv7/omap3/lowlevel_init.S
@@ -17,9 +17,6 @@
#include <asm/arch/clocks_omap3.h>
#include <linux/linkage.h>
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */
-
#ifdef CONFIG_SPL_BUILD
ENTRY(save_boot_params)
ldr r4, =omap3_boot_device
diff --git a/arch/arm/cpu/armv7/omap4/hw_data.c b/arch/arm/cpu/armv7/omap4/hw_data.c
index 4dec73e..029533c 100644
--- a/arch/arm/cpu/armv7/omap4/hw_data.c
+++ b/arch/arm/cpu/armv7/omap4/hw_data.c
@@ -172,6 +172,20 @@
.ddr = NULL
};
+struct dplls omap4430_dplls_es20 = {
+ .mpu = mpu_dpll_params_1200mhz,
+ .core = core_dpll_params_es2_1600mhz_ddr200mhz,
+ .per = per_dpll_params_1536mhz,
+ .iva = iva_dpll_params_1862mhz,
+#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
+ .abe = abe_dpll_params_sysclk_196608khz,
+#else
+ .abe = &abe_dpll_params_32k_196608khz,
+#endif
+ .usb = usb_dpll_params_1920mhz,
+ .ddr = NULL
+};
+
struct dplls omap4430_dplls = {
.mpu = mpu_dpll_params_1200mhz,
.core = core_dpll_params_1600mhz,
@@ -413,6 +427,10 @@
break;
case OMAP4430_ES2_0:
+ *dplls_data = &omap4430_dplls_es20;
+ *omap_vcores = &omap4430_volts;
+ break;
+
case OMAP4430_ES2_1:
case OMAP4430_ES2_2:
case OMAP4430_ES2_3:
diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c
index ff32807..7292161 100644
--- a/arch/arm/cpu/armv7/omap5/prcm-regs.c
+++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c
@@ -432,7 +432,7 @@
.control_srcomp_code_latch = 0x4A002E84,
.control_ddr_control_ext_0 = 0x4A002E88,
.control_padconf_core_base = 0x4A003400,
- .control_std_fuse_opp_vdd_mpu_2 = 0x4A003B24,
+ .control_std_fuse_opp_vdd_mpu_2 = 0x4A003B20,
.control_port_emif1_sdram_config = 0x4AE0C110,
.control_port_emif1_lpddr2_nvm_config = 0x4AE0C114,
.control_port_emif2_sdram_config = 0x4AE0C118,
diff --git a/arch/arm/cpu/armv7/socfpga/u-boot-spl.lds b/arch/arm/cpu/armv7/socfpga/u-boot-spl.lds
index a7c9c9d..4282beb 100644
--- a/arch/arm/cpu/armv7/socfpga/u-boot-spl.lds
+++ b/arch/arm/cpu/armv7/socfpga/u-boot-spl.lds
@@ -28,7 +28,11 @@
. = ALIGN(4);
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ }
.bss : {
. = ALIGN(4);
diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S
index 5aac773..ac1e55a 100644
--- a/arch/arm/cpu/armv7/start.S
+++ b/arch/arm/cpu/armv7/start.S
@@ -70,29 +70,6 @@
*
*************************************************************************/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
diff --git a/arch/arm/cpu/armv7/zynq/u-boot.lds b/arch/arm/cpu/armv7/zynq/u-boot.lds
index a68b050..f2a5965 100644
--- a/arch/arm/cpu/armv7/zynq/u-boot.lds
+++ b/arch/arm/cpu/armv7/zynq/u-boot.lds
@@ -60,7 +60,12 @@
*(.__rel_dyn_end)
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
+
+ _image_binary_end = .;
/*
* Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
diff --git a/arch/arm/cpu/armv8/config.mk b/arch/arm/cpu/armv8/config.mk
index 027a68c..f5b9559 100644
--- a/arch/arm/cpu/armv8/config.mk
+++ b/arch/arm/cpu/armv8/config.mk
@@ -6,10 +6,7 @@
#
PLATFORM_RELFLAGS += -fno-common -ffixed-x18
-# SEE README.arm-unaligned-accesses
-PF_NO_UNALIGNED := $(call cc-option, -mstrict-align)
-PLATFORM_NO_UNALIGNED := $(PF_NO_UNALIGNED)
-
PF_CPPFLAGS_ARMV8 := $(call cc-option, -march=armv8-a)
+PF_NO_UNALIGNED := $(call cc-option, -mstrict-align)
PLATFORM_CPPFLAGS += $(PF_CPPFLAGS_ARMV8)
PLATFORM_CPPFLAGS += $(PF_NO_UNALIGNED)
diff --git a/arch/arm/cpu/at91-common/u-boot-spl.lds b/arch/arm/cpu/at91-common/u-boot-spl.lds
index 038335d..57ac1eb 100644
--- a/arch/arm/cpu/at91-common/u-boot-spl.lds
+++ b/arch/arm/cpu/at91-common/u-boot-spl.lds
@@ -37,7 +37,11 @@
. = ALIGN(4);
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ } >.sram
.bss :
{
diff --git a/arch/arm/cpu/pxa/start.S b/arch/arm/cpu/pxa/start.S
index d8fb812..ae0d13c 100644
--- a/arch/arm/cpu/pxa/start.S
+++ b/arch/arm/cpu/pxa/start.S
@@ -84,32 +84,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
@@ -316,7 +290,6 @@
#ifdef CONFIG_SPL_BUILD
.align 5
do_hang:
- ldr sp, _TEXT_BASE /* use 32 words about stack */
bl hang /* hang and never return */
#else /* !CONFIG_SPL_BUILD */
.align 5
diff --git a/arch/arm/cpu/sa1100/start.S b/arch/arm/cpu/sa1100/start.S
index 27bcda5..bf80937 100644
--- a/arch/arm/cpu/sa1100/start.S
+++ b/arch/arm/cpu/sa1100/start.S
@@ -56,32 +56,6 @@
*************************************************************************
*/
-.globl _TEXT_BASE
-_TEXT_BASE:
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_TEXT_BASE)
- .word CONFIG_SPL_TEXT_BASE
-#else
- .word CONFIG_SYS_TEXT_BASE
-#endif
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
- .word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
- .word __bss_end - _start
-
-.globl _end_ofs
-_end_ofs:
- .word _end - _start
-
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
diff --git a/arch/arm/cpu/u-boot-spl.lds b/arch/arm/cpu/u-boot-spl.lds
index 4880d0f..3e88668 100644
--- a/arch/arm/cpu/u-boot-spl.lds
+++ b/arch/arm/cpu/u-boot-spl.lds
@@ -42,7 +42,12 @@
__rel_dyn_end = .;
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
+
+ _image_binary_end = .;
.bss __rel_dyn_start (OVERLAY) : {
__bss_start = .;
@@ -51,7 +56,7 @@
__bss_end = .;
}
- .dynsym _end : { *(.dynsym) }
+ .dynsym _image_binary_end : { *(.dynsym) }
.dynbss : { *(.dynbss) }
.dynstr : { *(.dynstr*) }
.dynamic : { *(.dynamic*) }
diff --git a/arch/arm/cpu/u-boot.lds b/arch/arm/cpu/u-boot.lds
index 4da5d24..87c2de2 100644
--- a/arch/arm/cpu/u-boot.lds
+++ b/arch/arm/cpu/u-boot.lds
@@ -60,7 +60,12 @@
*(.__rel_dyn_end)
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
+
+ _image_binary_end = .;
/*
* Deprecated: this MMU section is used by pxa at present but
@@ -91,7 +96,7 @@
KEEP(*(.__bss_end));
}
- .dynsym _end : { *(.dynsym) }
+ .dynsym _image_binary_end : { *(.dynsym) }
.dynbss : { *(.dynbss) }
.dynstr : { *(.dynstr*) }
.dynamic : { *(.dynamic*) }
diff --git a/arch/arm/include/asm/arch-am33xx/cpu.h b/arch/arm/include/asm/arch-am33xx/cpu.h
index 0736258..71bed4e 100644
--- a/arch/arm/include/asm/arch-am33xx/cpu.h
+++ b/arch/arm/include/asm/arch-am33xx/cpu.h
@@ -171,7 +171,8 @@
unsigned int resv11[1];
unsigned int wkup_uart0ctrl; /* offset 0xB4 */
unsigned int wkup_i2c0ctrl; /* offset 0xB8 */
- unsigned int resv12[7];
+ unsigned int wkup_adctscctrl; /* offset 0xBC */
+ unsigned int resv12[6];
unsigned int divm6dpllcore; /* offset 0xD8 */
};
@@ -221,7 +222,8 @@
unsigned int tpccclkctrl; /* offset 0xBC */
unsigned int dcan0clkctrl; /* offset 0xC0 */
unsigned int dcan1clkctrl; /* offset 0xC4 */
- unsigned int resv6[2];
+ unsigned int resv6;
+ unsigned int epwmss1clkctrl; /* offset 0xCC */
unsigned int emiffwclkctrl; /* offset 0xD0 */
unsigned int epwmss0clkctrl; /* offset 0xD4 */
unsigned int epwmss2clkctrl; /* offset 0xD8 */
@@ -353,7 +355,11 @@
unsigned int gpio2clkctrl; /* offset 0x480 */
unsigned int resv20;
unsigned int gpio3clkctrl; /* offset 0x488 */
- unsigned int resv21[7];
+ unsigned int resv41;
+ unsigned int gpio4clkctrl; /* offset 0x490 */
+ unsigned int resv42;
+ unsigned int gpio5clkctrl; /* offset 0x498 */
+ unsigned int resv21[3];
unsigned int i2c1clkctrl; /* offset 0x4A8 */
unsigned int resv22;
diff --git a/arch/arm/include/asm/arch-am33xx/ddr_defs.h b/arch/arm/include/asm/arch-am33xx/ddr_defs.h
index fbe599d..4d89952 100644
--- a/arch/arm/include/asm/arch-am33xx/ddr_defs.h
+++ b/arch/arm/include/asm/arch-am33xx/ddr_defs.h
@@ -58,6 +58,22 @@
#define MT41J128MJT125_PHY_FIFO_WE 0x100
#define MT41J128MJT125_IOCTRL_VALUE 0x18B
+/* Micron MT41K128M16JT-187E */
+#define MT41K128MJT187E_EMIF_READ_LATENCY 0x06
+#define MT41K128MJT187E_EMIF_TIM1 0x0888B3DB
+#define MT41K128MJT187E_EMIF_TIM2 0x36337FDA
+#define MT41K128MJT187E_EMIF_TIM3 0x501F830F
+#define MT41K128MJT187E_EMIF_SDCFG 0x61C04AB2
+#define MT41K128MJT187E_EMIF_SDREF 0x0000093B
+#define MT41K128MJT187E_ZQ_CFG 0x50074BE4
+#define MT41K128MJT187E_RATIO 0x40
+#define MT41K128MJT187E_INVERT_CLKOUT 0x1
+#define MT41K128MJT187E_RD_DQS 0x3B
+#define MT41K128MJT187E_WR_DQS 0x85
+#define MT41K128MJT187E_PHY_WR_DATA 0xC1
+#define MT41K128MJT187E_PHY_FIFO_WE 0x100
+#define MT41K128MJT187E_IOCTRL_VALUE 0x18B
+
/* Micron MT41J64M16JT-125 */
#define MT41J64MJT125_EMIF_SDCFG 0x61C04A32
diff --git a/arch/arm/include/asm/arch-am33xx/gpio.h b/arch/arm/include/asm/arch-am33xx/gpio.h
index a1ffd49..220603d 100644
--- a/arch/arm/include/asm/arch-am33xx/gpio.h
+++ b/arch/arm/include/asm/arch-am33xx/gpio.h
@@ -12,8 +12,8 @@
#define AM33XX_GPIO1_BASE 0x4804C000
#define AM33XX_GPIO2_BASE 0x481AC000
#define AM33XX_GPIO3_BASE 0x481AE000
-
-#define GPIO_22 22
+#define AM33XX_GPIO4_BASE 0x48320000
+#define AM33XX_GPIO5_BASE 0x48322000
/* GPIO CTRL register */
#define GPIO_CTRL_DISABLEMODULE_SHIFT 0
diff --git a/arch/arm/include/asm/arch-bcm281xx/gpio.h b/arch/arm/include/asm/arch-bcm281xx/gpio.h
new file mode 100644
index 0000000..1b40a96
--- /dev/null
+++ b/arch/arm/include/asm/arch-bcm281xx/gpio.h
@@ -0,0 +1,15 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __ARCH_BCM281XX_GPIO_H
+#define __ARCH_BCM281XX_GPIO_H
+
+/*
+ * Empty file - cmd_gpio.c requires this. The implementation
+ * is in drivers/gpio/kona_gpio.c instead of inlined here.
+ */
+
+#endif
diff --git a/arch/arm/include/asm/arch-bcm281xx/sysmap.h b/arch/arm/include/asm/arch-bcm281xx/sysmap.h
new file mode 100644
index 0000000..880b4e0
--- /dev/null
+++ b/arch/arm/include/asm/arch-bcm281xx/sysmap.h
@@ -0,0 +1,25 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __ARCH_BCM281XX_SYSMAP_H
+
+#define BSC1_BASE_ADDR 0x3e016000
+#define BSC2_BASE_ADDR 0x3e017000
+#define BSC3_BASE_ADDR 0x3e018000
+#define GPIO2_BASE_ADDR 0x35003000
+#define KONA_MST_CLK_BASE_ADDR 0x3f001000
+#define KONA_SLV_CLK_BASE_ADDR 0x3e011000
+#define PMU_BSC_BASE_ADDR 0x3500d000
+#define PWRMGR_BASE_ADDR 0x35010000
+#define SDIO1_BASE_ADDR 0x3f180000
+#define SDIO2_BASE_ADDR 0x3f190000
+#define SDIO3_BASE_ADDR 0x3f1a0000
+#define SDIO4_BASE_ADDR 0x3f1b0000
+#define SECWD_BASE_ADDR 0x3500c000
+#define SECWD2_BASE_ADDR 0x35002f40
+#define TIMER_BASE_ADDR 0x3e00d000
+
+#endif
diff --git a/arch/arm/include/asm/kona-common/clk.h b/arch/arm/include/asm/kona-common/clk.h
new file mode 100644
index 0000000..2c7e829
--- /dev/null
+++ b/arch/arm/include/asm/kona-common/clk.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/* This API file is loosely based on u-boot/drivers/video/ipu.h and linux */
+
+#ifndef __KONA_COMMON_CLK_H
+#define __KONA_COMMON_CLK_H
+
+#include <linux/types.h>
+
+struct clk;
+
+/* Only implement required functions for your specific architecture */
+int clk_init(void);
+struct clk *clk_get(const char *id);
+int clk_enable(struct clk *clk);
+void clk_disable(struct clk *clk);
+unsigned long clk_get_rate(struct clk *clk);
+long clk_round_rate(struct clk *clk, unsigned long rate);
+int clk_set_rate(struct clk *clk, unsigned long rate);
+int clk_set_parent(struct clk *clk, struct clk *parent);
+struct clk *clk_get_parent(struct clk *clk);
+int clk_sdio_enable(void *base, u32 rate, u32 *actual_ratep);
+int clk_bsc_enable(void *base);
+
+#endif
diff --git a/arch/arm/include/asm/kona-common/kona_sdhci.h b/arch/arm/include/asm/kona-common/kona_sdhci.h
new file mode 100644
index 0000000..1ff0e55
--- /dev/null
+++ b/arch/arm/include/asm/kona-common/kona_sdhci.h
@@ -0,0 +1,12 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __KONA_SDHCI_H
+#define __KONA_SDHCI_H
+
+int kona_sdhci_init(int dev_index, u32 min_clk, u32 quirks);
+
+#endif
diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile
index 321997c..45febcf 100644
--- a/arch/arm/lib/Makefile
+++ b/arch/arm/lib/Makefile
@@ -32,7 +32,6 @@
ifndef CONFIG_SYS_GENERIC_BOARD
obj-y += board.o
endif
-obj-y += sections.o
obj-$(CONFIG_OF_LIBFDT) += bootm-fdt.o
obj-$(CONFIG_CMD_BOOTM) += bootm.o
@@ -43,6 +42,7 @@
obj-$(CONFIG_SPL_FRAMEWORK) += spl.o
endif
+obj-y += sections.o
ifdef CONFIG_ARM64
obj-y += interrupts_64.o
else
diff --git a/arch/arm/lib/board.c b/arch/arm/lib/board.c
index ba62394..e9a7708 100644
--- a/arch/arm/lib/board.c
+++ b/arch/arm/lib/board.c
@@ -105,8 +105,8 @@
{
printf("\n\n%s\n\n", version_string);
debug("U-Boot code: %08lX -> %08lX BSS: -> %08lX\n",
- _TEXT_BASE,
- _bss_start_ofs + _TEXT_BASE, _bss_end_ofs + _TEXT_BASE);
+ (ulong)&_start,
+ (ulong)&__bss_start, (ulong)&__bss_end);
#ifdef CONFIG_MODEM_SUPPORT
debug("Modem Support enabled\n");
#endif
@@ -273,13 +273,13 @@
memset((void *)gd, 0, sizeof(gd_t));
- gd->mon_len = _bss_end_ofs;
+ gd->mon_len = (ulong)&__bss_end - (ulong)_start;
#ifdef CONFIG_OF_EMBED
/* Get a pointer to the FDT */
gd->fdt_blob = __dtb_db_begin;
#elif defined CONFIG_OF_SEPARATE
/* FDT is at end of image */
- gd->fdt_blob = (void *)(_end_ofs + _TEXT_BASE);
+ gd->fdt_blob = &_end;
#endif
/* Allow the early environment to override the fdt address */
gd->fdt_blob = (void *)getenv_ulong("fdtcontroladdr", 16,
@@ -451,7 +451,7 @@
gd->relocaddr = addr;
gd->start_addr_sp = addr_sp;
- gd->reloc_off = addr - _TEXT_BASE;
+ gd->reloc_off = addr - (ulong)&_start;
debug("relocation Offset is: %08lx\n", gd->reloc_off);
if (new_fdt) {
memcpy(new_fdt, gd->fdt_blob, fdt_size);
@@ -516,7 +516,7 @@
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
- monitor_flash_len = _end_ofs;
+ monitor_flash_len = (ulong)&__rel_dyn_end - (ulong)_start;
/* Enable caches */
enable_caches();
diff --git a/arch/arm/lib/interrupts.c b/arch/arm/lib/interrupts.c
index 603bf14..758b013 100644
--- a/arch/arm/lib/interrupts.c
+++ b/arch/arm/lib/interrupts.c
@@ -153,7 +153,7 @@
void do_data_abort (struct pt_regs *pt_regs)
{
- printf ("data abort\n\n MAYBE you should read doc/README.arm-unaligned-accesses\n\n");
+ printf ("data abort\n");
show_regs (pt_regs);
bad_mode ();
}
diff --git a/arch/arm/lib/sections.c b/arch/arm/lib/sections.c
index e35687c..5b30bcb 100644
--- a/arch/arm/lib/sections.c
+++ b/arch/arm/lib/sections.c
@@ -25,3 +25,4 @@
char __image_copy_end[0] __attribute__((section(".__image_copy_end")));
char __rel_dyn_start[0] __attribute__((section(".__rel_dyn_start")));
char __rel_dyn_end[0] __attribute__((section(".__rel_dyn_end")));
+char _end[0] __attribute__((section(".__end")));
diff --git a/board/Barix/ipam390/u-boot-spl-ipam390.lds b/board/Barix/ipam390/u-boot-spl-ipam390.lds
index 5480d1f..8604696 100644
--- a/board/Barix/ipam390/u-boot-spl-ipam390.lds
+++ b/board/Barix/ipam390/u-boot-spl-ipam390.lds
@@ -49,5 +49,9 @@
} >.sram
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ } >.sram
}
diff --git a/board/BuR/common/bur_common.h b/board/BuR/common/bur_common.h
new file mode 100644
index 0000000..15225b0
--- /dev/null
+++ b/board/BuR/common/bur_common.h
@@ -0,0 +1,22 @@
+/*
+ * bur_comon.h
+ *
+ * common board information header for B&R boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _BUR_COMMON_H_
+#define _BUR_COMMON_H_
+
+void blink(u32 blinks, u32 intervall, u32 pin);
+void pmicsetup(u32 mpupll);
+void enable_uart0_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(void);
+int board_eth_init(bd_t *bis);
+
+#endif
diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c
new file mode 100644
index 0000000..6d187ea
--- /dev/null
+++ b/board/BuR/common/common.c
@@ -0,0 +1,216 @@
+/*
+ * common.c
+ *
+ * common board functions for B&R boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include "bur_common.h"
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+/* --------------------------------------------------------------------------*/
+void blink(u32 blinks, u32 intervall, u32 pin)
+{
+ gpio_direction_output(pin, 0);
+ int val = 0;
+
+ do {
+ val ^= 0x01;
+ gpio_set_value(pin, val);
+ mdelay(intervall);
+ } while (blinks--);
+
+ gpio_set_value(pin, 0);
+}
+#ifdef CONFIG_SPL_BUILD
+void pmicsetup(u32 mpupll)
+{
+ int mpu_vdd;
+ int usb_cur_lim;
+
+ /* setup I2C */
+ enable_i2c0_pin_mux();
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+ if (i2c_probe(TPS65217_CHIP_PM)) {
+ puts("PMIC (0x24) not found! skip further initalization.\n");
+ return;
+ }
+
+ /* Get the frequency which is defined by device fuses */
+ dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+ printf("detected max. frequency: %d - ", dpll_mpu_opp100.m);
+
+ if (0 != mpupll) {
+ dpll_mpu_opp100.m = MPUPLL_M_1000;
+ printf("retuning MPU-PLL to: %d MHz.\n", dpll_mpu_opp100.m);
+ } else {
+ puts("ok.\n");
+ }
+ /*
+ * Increase USB current limit to 1300mA or 1800mA and set
+ * the MPU voltage controller as needed.
+ */
+ if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
+ usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
+ mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
+ } else {
+ usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
+ mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
+ }
+
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
+ usb_cur_lim, TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+ puts("tps65217_reg_write failure\n");
+
+ /* Set DCDC3 (CORE) voltage to 1.125V */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+ TPS65217_DCDC_VOLT_SEL_1125MV)) {
+ puts("tps65217_voltage_update failure\n");
+ return;
+ }
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* Set DCDC2 (MPU) voltage */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
+ puts("tps65217_voltage_update failure\n");
+ return;
+ }
+
+ /* Set LDO3 to 1.8V */
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+ TPS65217_DEFLS1,
+ TPS65217_LDO_VOLTAGE_OUT_1_8,
+ TPS65217_LDO_MASK))
+ puts("tps65217_reg_write failure\n");
+ /* Set LDO4 to 3.3V */
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+ TPS65217_DEFLS2,
+ TPS65217_LDO_VOLTAGE_OUT_3_3,
+ TPS65217_LDO_MASK))
+ puts("tps65217_reg_write failure\n");
+
+ /* Set MPU Frequency to what we detected now that voltages are set */
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+void set_uart_mux_conf(void)
+{
+ enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+ enable_board_pin_mux();
+}
+
+#endif /* CONFIG_SPL_BUILD */
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+ return;
+}
+
+/* describing port offsets of TI's CPSW block */
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_id = 0,
+ },
+ {
+ .slave_reg_ofs = 0x308,
+ .sliver_reg_ofs = 0xdc0,
+ .phy_id = 1,
+ },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+
+#if defined(CONFIG_DRIVER_TI_CPSW)
+
+int board_eth_init(bd_t *bis)
+{
+ int rv = 0;
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+
+ /* try reading mac address from efuse */
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+ if (!getenv("ethaddr")) {
+ printf("<ethaddr> not set. Validating first E-fuse MAC ... ");
+
+ if (is_valid_ether_addr(mac_addr)) {
+ printf("using: %02X:%02X:%02X:%02X:%02X:%02X.\n",
+ mac_addr[0], mac_addr[1], mac_addr[2],
+ mac_addr[3], mac_addr[4], mac_addr[5]
+ );
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ }
+ }
+ writel(MII_MODE_ENABLE, &cdev->miisel);
+ cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
+ cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0) {
+ printf("Error %d registering CPSW switch\n", rv);
+ return 0;
+ }
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+ return rv;
+}
+#endif /* CONFIG_DRIVER_TI_CPSW */
diff --git a/board/BuR/kwb/Makefile b/board/BuR/kwb/Makefile
new file mode 100644
index 0000000..7b04b26
--- /dev/null
+++ b/board/BuR/kwb/Makefile
@@ -0,0 +1,12 @@
+#
+# Makefile
+#
+# Copyright (C) 2014 Hannes Petermaier <oe5hpm@oevsv.at> -
+# Bernecker & Rainer Industrielektronik GmbH - http://www.br-automation.com/
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_SPL_BUILD) += mux.o
+obj-y += ../common/common.o
+obj-y += board.o
diff --git a/board/BuR/kwb/board.c b/board/BuR/kwb/board.c
new file mode 100644
index 0000000..8aa16bc
--- /dev/null
+++ b/board/BuR/kwb/board.c
@@ -0,0 +1,240 @@
+/*
+ * board.c
+ *
+ * Board functions for B&R KWB Board
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <power/tps65217.h>
+#include "../common/bur_common.h"
+
+/* -------------------------------------------------------------------------*/
+/* -- defines for used GPIO Hardware -- */
+#define KEY (0+4)
+#define LCD_PWR (0+5)
+#define PUSH_KEY (0+31)
+#define USB2SD_NRST (32+29)
+#define USB2SD_PWR (96+13)
+/* -------------------------------------------------------------------------*/
+/* -- PSOC Resetcontroller Register defines -- */
+
+/* I2C Address of controller */
+#define RSTCTRL_ADDR 0x75
+/* Register for CTRL-word */
+#define RSTCTRL_CTRLREG 0x01
+/* Register for giving some information to VxWorks OS */
+#define RSTCTRL_SCRATCHREG 0x04
+
+/* -- defines for RSTCTRL_CTRLREG -- */
+#define RSTCTRL_FORCE_PWR_NEN 0x0404
+
+#if defined(CONFIG_SPL_BUILD)
+/* TODO: check ram-timing ! */
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41K256M16HA125E_RD_DQS,
+ .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+ .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41K256M16HA125E_RATIO,
+ .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd1csratio = MT41K256M16HA125E_RATIO,
+ .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd2csratio = MT41K256M16HA125E_RATIO,
+ .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+ .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+ .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+ .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+ .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+ .zq_config = MT41K256M16HA125E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+static const struct ctrl_ioregs ddr3_ioregs = {
+ .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+#define OSC (V_OSCK/1000000)
+const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ unsigned int oldspeed;
+ unsigned short buf;
+
+ struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
+ struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;
+ /*
+ * enable additional clocks of modules which are accessed later from
+ * VxWorks OS
+ */
+ u32 *const clk_domains[] = { 0 };
+
+ u32 *const clk_modules_kwbspecific[] = {
+ &cmwkup->wkup_adctscctrl,
+ &cmper->spi1clkctrl,
+ &cmper->dcan0clkctrl,
+ &cmper->dcan1clkctrl,
+ &cmper->epwmss0clkctrl,
+ &cmper->epwmss1clkctrl,
+ &cmper->epwmss2clkctrl,
+ 0
+ };
+ do_enable_clocks(clk_domains, clk_modules_kwbspecific, 1);
+
+ /* power-OFF LCD-Display */
+ gpio_direction_output(LCD_PWR, 0);
+
+ /* setup I2C */
+ enable_i2c0_pin_mux();
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+ /* power-ON 3V3 via Resetcontroller */
+ oldspeed = i2c_get_bus_speed();
+ if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) {
+ buf = RSTCTRL_FORCE_PWR_NEN;
+ i2c_write(RSTCTRL_ADDR, RSTCTRL_CTRLREG, 1,
+ (uint8_t *)&buf, sizeof(buf));
+ i2c_set_bus_speed(oldspeed);
+ } else {
+ puts("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n");
+ }
+
+#if defined(CONFIG_AM335X_USB0)
+ /* power on USB2SD Controller */
+ gpio_direction_output(USB2SD_PWR, 1);
+ mdelay(1);
+ /* give a reset Pulse to USB2SD Controller */
+ gpio_direction_output(USB2SD_NRST, 0);
+ mdelay(1);
+ gpio_set_value(USB2SD_NRST, 1);
+#endif
+ pmicsetup(0);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ return &dpll_ddr3;
+}
+
+void sdram_init(void)
+{
+ config_ddr(400, &ddr3_ioregs,
+ &ddr3_data,
+ &ddr3_cmd_ctrl_data,
+ &ddr3_emif_reg_data, 0);
+}
+#endif /* CONFIG_SPL_BUILD */
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+ gpmc_init();
+ return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+ const unsigned int ton = 250;
+ const unsigned int toff = 1000;
+ unsigned int cnt = 3;
+ unsigned short buf = 0xAAAA;
+ unsigned int oldspeed;
+
+ tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+ TPS65217_WLEDCTRL2, 0x32, 0xFF); /* 50% dimlevel */
+
+ if (gpio_get_value(KEY)) {
+ do {
+ /* turn on light */
+ tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+ TPS65217_WLEDCTRL1, 0x09, 0xFF);
+ mdelay(ton);
+ /* turn off light */
+ tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+ TPS65217_WLEDCTRL1, 0x01, 0xFF);
+ mdelay(toff);
+ cnt--;
+ if (!gpio_get_value(KEY) &&
+ gpio_get_value(PUSH_KEY) && 1 == cnt) {
+ puts("updating from USB ...\n");
+ setenv("bootcmd", "run usbupdate");
+ break;
+ } else if (!gpio_get_value(KEY)) {
+ break;
+ }
+ } while (cnt);
+ }
+
+ switch (cnt) {
+ case 0:
+ puts("3 blinks ... entering BOOT mode.\n");
+ buf = 0x0000;
+ break;
+ case 1:
+ puts("2 blinks ... entering DIAGNOSE mode.\n");
+ buf = 0x0F0F;
+ break;
+ case 2:
+ puts("1 blinks ... entering SERVICE mode.\n");
+ buf = 0xB4B4;
+ break;
+ case 3:
+ puts("0 blinks ... entering RUN mode.\n");
+ buf = 0x0404;
+ break;
+ }
+ mdelay(ton);
+ /* turn on light */
+ tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+ TPS65217_WLEDCTRL1, 0x09, 0xFF);
+ /* write bootinfo into scratchregister of resetcontroller */
+ oldspeed = i2c_get_bus_speed();
+ if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) {
+ i2c_write(RSTCTRL_ADDR, RSTCTRL_SCRATCHREG, 1,
+ (uint8_t *)&buf, sizeof(buf));
+ i2c_set_bus_speed(oldspeed);
+ } else {
+ puts("ERROR: i2c_set_bus_speed failed! (scratchregister)\n");
+ }
+ /*
+ * reset VBAR registers to its reset location, VxWorks 6.9.3.2 does
+ * expect that vectors are there, original u-boot moves them to _start
+ */
+ __asm__("ldr r0,=0x20000");
+ __asm__("mcr p15, 0, r0, c12, c0, 0"); /* Set VBAR */
+
+ return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
diff --git a/board/BuR/kwb/mux.c b/board/BuR/kwb/mux.c
new file mode 100644
index 0000000..1a5ffd5
--- /dev/null
+++ b/board/BuR/kwb/mux.c
@@ -0,0 +1,195 @@
+/*
+ * mux.c
+ *
+ * Pinmux Setting for B&R LEIT Board(s)
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+
+static struct module_pin_mux usb0_pin_mux[] = {
+ {OFFSET(usb0_id), (MODE(0) | RXACTIVE)},
+ /* USB0 DrvBus Receiver disable (from romcode 0x20) */
+ {OFFSET(usb0_drvvbus), (MODE(0))},
+ /* USB1 DrvBus as GPIO due to HW-Workaround */
+ {OFFSET(usb1_drvvbus), (MODE(7))},
+ {-1},
+};
+static struct module_pin_mux spi1_pin_mux[] = {
+ /* SPI1_SCLK */
+ {OFFSET(mcasp0_aclkx), MODE(3) | PULLUDEN | RXACTIVE},
+ /* SPI1_D0 */
+ {OFFSET(mcasp0_fsx), MODE(3) | PULLUDEN | RXACTIVE},
+ /* SPI1_D1 */
+ {OFFSET(mcasp0_axr0), MODE(3) | PULLUDEN | RXACTIVE},
+ /* SPI1_CS0 */
+ {OFFSET(mcasp0_ahclkr), MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE},
+ {-1},
+};
+
+static struct module_pin_mux dcan0_pin_mux[] = {
+ /* DCAN0 TX */
+ {OFFSET(uart1_ctsn), MODE(2) | PULLUDEN | PULLUP_EN},
+ /* DCAN0 RX */
+ {OFFSET(uart1_rtsn), MODE(2) | RXACTIVE},
+ {-1},
+};
+
+static struct module_pin_mux dcan1_pin_mux[] = {
+ /* DCAN1 TX */
+ {OFFSET(uart1_rxd), MODE(2) | PULLUDEN | PULLUP_EN},
+ /* DCAN1 RX */
+ {OFFSET(uart1_txd), MODE(2) | RXACTIVE},
+ {-1},
+};
+
+static struct module_pin_mux gpios[] = {
+ /* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+ {OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS)},
+ /* GPIO0_4 (SPI D1) - TA602 */
+ {OFFSET(spi0_d1), (MODE(7) | PULLUDDIS | RXACTIVE)},
+ /* GPIO0_5 (SPI CS0) - DISPLAY_ON_OFF */
+ {OFFSET(spi0_cs0), (MODE(7) | PULLUDDIS)},
+ /* GPIO0_7 (PWW0 OUT) - CAN TERM */
+ {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDDIS | RXACTIVE)},
+ /* GPIO0_19 (DMA_INTR0) - CLKOUT SYS */
+ {OFFSET(xdma_event_intr0), (MODE(7) | RXACTIVE)},
+ /* GPIO0_20 (DMA_INTR1) - SPI1 nCS1 */
+ {OFFSET(xdma_event_intr1), (MODE(7) | PULLUDEN | PULLUP_EN)},
+ /* GPIO0_30 (GPMC_WAIT0) - TA601 */
+ {OFFSET(gpmc_wait0), (MODE(7) | PULLUDDIS | RXACTIVE)},
+ /* GPIO0_31 (GPMC_nWP) - SW601 PushButton */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUDDIS | RXACTIVE)},
+ /* GPIO1_28 (GPMC_nWE) - FRAM_nWP */
+ {OFFSET(gpmc_be1n), (MODE(7) | PULLUDDIS)},
+ /* GPIO2_0 (GPMC_nCS3) - VBAT_OK */
+ {OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
+ /* GPIO2_2 (GPMC_nADV_ALE) - DCOK */
+ {OFFSET(gpmc_advn_ale), (MODE(7) | PULLUDDIS | RXACTIVE)},
+ /* GPIO2_4 (GPMC_nWE) - TST_BAST */
+ {OFFSET(gpmc_wen), (MODE(7) | PULLUDDIS)},
+ /* GPIO3_18 (MCASP0_ACLKR) - SW601 CNTup, mapped to Counter eQEB0A_in */
+ {OFFSET(mcasp0_aclkr), (MODE(1) | PULLUDDIS | RXACTIVE)},
+ /* GPIO3_19 (MCASP0_FSR) - SW601 CNTdown, mapped to Counter eQEB0B_in */
+ {OFFSET(mcasp0_fsr), (MODE(1) | PULLUDDIS | RXACTIVE)},
+ /* GPIO3_20 (MCASP0_AXR1) - SW601 CNTdown, map to Counter eQEB0_index */
+ {OFFSET(mcasp0_axr1), (MODE(1) | PULLUDDIS | RXACTIVE)},
+ {-1},
+};
+
+static struct module_pin_mux uart0_pin_mux[] = {
+ /* UART0_CTS */
+ {OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART0_RXD */
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART0_TXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+ {-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+ /* I2C_DATA */
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+ /* I2C_SCLK */
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+ {-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+ {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */
+ {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */
+ {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */
+ {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */
+ {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */
+ {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */
+ {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */
+ {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */
+ {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */
+ {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */
+ {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */
+ {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */
+ {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {-1},
+};
+
+static struct module_pin_mux mmc1_pin_mux[] = {
+ {OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT3 */
+ {OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT2 */
+ {OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT1 */
+ {OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT0 */
+ {OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CLK */
+ {OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CMD */
+ {OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)}, /* MMC1_WP */
+ {OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+
+ {-1},
+};
+
+static struct module_pin_mux lcd_pin_mux[] = {
+ {OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)}, /* LCD-Data(0) */
+ {OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)}, /* LCD-Data(1) */
+ {OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)}, /* LCD-Data(2) */
+ {OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)}, /* LCD-Data(3) */
+ {OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)}, /* LCD-Data(4) */
+ {OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)}, /* LCD-Data(5) */
+ {OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)}, /* LCD-Data(6) */
+ {OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)}, /* LCD-Data(7) */
+ {OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)}, /* LCD-Data(8) */
+ {OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)}, /* LCD-Data(9) */
+ {OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)}, /* LCD-Data(10) */
+ {OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)}, /* LCD-Data(11) */
+ {OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)}, /* LCD-Data(12) */
+ {OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)}, /* LCD-Data(13) */
+ {OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)}, /* LCD-Data(14) */
+ {OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)}, /* LCD-Data(15) */
+
+ {OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)}, /* LCD-Data(16) */
+ {OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)}, /* LCD-Data(17) */
+ {OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)}, /* LCD-Data(18) */
+ {OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)}, /* LCD-Data(19) */
+ {OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)}, /* LCD-Data(20) */
+ {OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)}, /* LCD-Data(21) */
+ {OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)}, /* LCD-Data(22) */
+ {OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)}, /* LCD-Data(23) */
+
+ {OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)}, /* LCD-VSync */
+ {OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)}, /* LCD-HSync */
+ {OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
+ {OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)}, /* LCD-CLK */
+
+ {-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+ configure_module_pin_mux(mii1_pin_mux);
+ configure_module_pin_mux(usb0_pin_mux);
+ configure_module_pin_mux(spi1_pin_mux);
+ configure_module_pin_mux(dcan0_pin_mux);
+ configure_module_pin_mux(dcan1_pin_mux);
+ configure_module_pin_mux(mmc1_pin_mux);
+ configure_module_pin_mux(lcd_pin_mux);
+ configure_module_pin_mux(gpios);
+}
diff --git a/board/BuR/tseries/Makefile b/board/BuR/tseries/Makefile
new file mode 100644
index 0000000..ec0d27a
--- /dev/null
+++ b/board/BuR/tseries/Makefile
@@ -0,0 +1,14 @@
+#
+# Makefile
+#
+# Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+# Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD),y)
+obj-y := mux.o
+endif
+obj-y += ../common/common.o
+obj-y += board.o
diff --git a/board/BuR/tseries/board.c b/board/BuR/tseries/board.c
new file mode 100644
index 0000000..f0510e5
--- /dev/null
+++ b/board/BuR/tseries/board.c
@@ -0,0 +1,147 @@
+/*
+ * board.c
+ *
+ * Board functions for B&R LEIT Board
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <power/tps65217.h>
+#include "../common/bur_common.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* --------------------------------------------------------------------------*/
+/* -- defines for GPIO -- */
+#define ETHLED_ORANGE (96+16) /* GPIO3_16 */
+#define REPSWITCH (0+20) /* GPIO0_20 */
+
+
+#if defined(CONFIG_SPL_BUILD)
+/* TODO: check ram-timing ! */
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41K256M16HA125E_RD_DQS,
+ .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+ .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41K256M16HA125E_RATIO,
+ .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd1csratio = MT41K256M16HA125E_RATIO,
+ .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd2csratio = MT41K256M16HA125E_RATIO,
+ .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+ .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+ .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+ .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+ .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+ .zq_config = MT41K256M16HA125E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+static const struct ctrl_ioregs ddr3_ioregs = {
+ .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+/*
+ * called from spl_nand.c
+ * return 0 for loading linux, return 1 for loading u-boot
+ */
+int spl_start_uboot(void)
+{
+ if (0 == gpio_get_value(REPSWITCH)) {
+ blink(5, 125, ETHLED_ORANGE);
+ mdelay(1000);
+ printf("SPL: entering u-boot instead kernel image.\n");
+ return 1;
+ }
+ return 0;
+}
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#define OSC (V_OSCK/1000000)
+static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ pmicsetup(1000);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ return &dpll_ddr3;
+}
+
+void sdram_init(void)
+{
+ config_ddr(400, &ddr3_ioregs,
+ &ddr3_data,
+ &ddr3_cmd_ctrl_data,
+ &ddr3_emif_reg_data, 0);
+}
+#endif /* CONFIG_SPL_BUILD */
+
+/* Basic board specific setup. Pinmux has been handled already. */
+int board_init(void)
+{
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+ gpmc_init();
+ return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+ gpio_direction_output(ETHLED_ORANGE, 0);
+
+ if (0 == gpio_get_value(REPSWITCH)) {
+ printf("\n\n\n"
+ "!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n"
+ "!!!!!!! recovery switch activated !!!!!!!\n"
+ "!!!!!!! running usbupdate !!!!!!!\n"
+ "!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n\n\n");
+ setenv("bootcmd", "sleep 2; run netupdate;");
+ }
+
+ printf("turning on display power+backlight ... ");
+ tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL1,
+ 0x09, TPS65217_MASK_ALL_BITS); /* 200 Hz, ON */
+ tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL2,
+ 0x62, TPS65217_MASK_ALL_BITS); /* 100% */
+ printf("ok.\n");
+
+ return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
diff --git a/board/BuR/tseries/mux.c b/board/BuR/tseries/mux.c
new file mode 100644
index 0000000..3c76e96
--- /dev/null
+++ b/board/BuR/tseries/mux.c
@@ -0,0 +1,225 @@
+/*
+ * mux.c
+ *
+ * Pinmux Setting for B&R LEIT Board(s)
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+
+static struct module_pin_mux uart0_pin_mux[] = {
+ /* UART0_CTS */
+ {OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART0_RXD */
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* UART0_TXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+ {-1},
+};
+#ifdef CONFIG_MMC
+static struct module_pin_mux mmc1_pin_mux[] = {
+ {OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT3 */
+ {OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT2 */
+ {OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT1 */
+ {OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT0 */
+ {OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CLK */
+ {OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CMD */
+ {OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)}, /* MMC1_WP */
+ {OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+ {-1},
+};
+#endif
+static struct module_pin_mux i2c0_pin_mux[] = {
+ /* I2C_DATA */
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+ /* I2C_SCLK */
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+ {-1},
+};
+
+static struct module_pin_mux spi0_pin_mux[] = {
+ /* SPI0_SCLK */
+ {OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ /* SPI0_D0 */
+ {OFFSET(spi0_d0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ /* SPI0_D1 */
+ {OFFSET(spi0_d1), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ /* SPI0_CS0 */
+ {OFFSET(spi0_cs0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+ {-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+ {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */
+ {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */
+ {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */
+ {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */
+ {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */
+ {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */
+ {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */
+ {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */
+ {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */
+ {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */
+ {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */
+ {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */
+ {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {-1},
+};
+
+static struct module_pin_mux mii2_pin_mux[] = {
+ {OFFSET(gpmc_a0), MODE(1)}, /* MII2_TXEN */
+ {OFFSET(gpmc_a1), MODE(1) | RXACTIVE}, /* MII2_RXDV */
+ {OFFSET(gpmc_a2), MODE(1)}, /* MII2_TXD3 */
+ {OFFSET(gpmc_a3), MODE(1)}, /* MII2_TXD2 */
+ {OFFSET(gpmc_a4), MODE(1)}, /* MII2_TXD1 */
+ {OFFSET(gpmc_a5), MODE(1)}, /* MII2_TXD0 */
+ {OFFSET(gpmc_a6), MODE(1) | RXACTIVE}, /* MII2_TXCLK */
+ {OFFSET(gpmc_a7), MODE(1) | RXACTIVE}, /* MII2_RXCLK */
+ {OFFSET(gpmc_a8), MODE(1) | RXACTIVE}, /* MII2_RXD3 */
+ {OFFSET(gpmc_a9), MODE(1) | RXACTIVE}, /* MII2_RXD2 */
+ {OFFSET(gpmc_a10), MODE(1) | RXACTIVE}, /* MII2_RXD1 */
+ {OFFSET(gpmc_a11), MODE(1) | RXACTIVE}, /* MII2_RXD0 */
+ {OFFSET(gpmc_wpn), (MODE(1) | RXACTIVE)},/* MII2_RXERR */
+ /*
+ * MII2_CRS is shared with
+ * NAND_WAIT0
+ */
+ {OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */
+ {-1},
+};
+#ifdef CONFIG_NAND
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
+ {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
+ {-1},
+};
+#endif
+static struct module_pin_mux gpIOs[] = {
+ /* GPIO0_6 (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */
+ {OFFSET(spi0_cs1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* TIMER5 (MMC0_DAT3) - TIMER5 (Buzzer) */
+ {OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)},
+ /* TIMER6 (MMC0_DAT2) - PWM_BACK_3V3, later used as MODE3 for PWM */
+ {OFFSET(mmc0_dat2), (MODE(7) | PULLUDEN | RXACTIVE)},
+ /* GPIO2_28 (MMC0_DAT1) - MII_nNAND */
+ {OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)},
+ /* GPIO2_29 (MMC0_DAT0) - NAND_1n0 */
+ {OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)},
+ /* GPIO2_30 (MMC0_CLK) - nRESET (PHY) */
+ {OFFSET(mmc0_clk), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_18 (MCASP0_ACLKR) - CPLD JTAG TDI */
+ {OFFSET(mcasp0_aclkr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_19 (MCASP0_FSR) - CPLD JTAG TMS */
+ {OFFSET(mcasp0_fsr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_20 (MCASP0_AXR1) - CPLD JTAG TCK */
+ {OFFSET(mcasp0_axr1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_21 (MCASP0_AHCLKX) - CPLD JTAG TDO */
+ {OFFSET(mcasp0_ahclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO2_0 (GPMC_nCS3) - DCOK */
+ {OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
+ /* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+ {OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS | RXACTIVE) },
+ /*
+ * GPIO0_7 (PWW0 OUT)
+ * DISPLAY_ONOFF (Backlight Enable at LVDS Versions)
+ */
+ {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN | RXACTIVE)},
+ /* GPIO0_19 (DMA_INTR0) - ISPLAY_MODE (CPLD) */
+ {OFFSET(xdma_event_intr0), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+ /* GPIO0_20 (DMA_INTR1) - REP-Switch */
+ {OFFSET(xdma_event_intr1), (MODE(7) | PULLUP_EN | RXACTIVE)},
+ /* GPIO3_14 (MCASP0_ACLKX) - frei / PP709 */
+ {OFFSET(mcasp0_aclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+ /* GPIO3_15 (MCASP0_FSX) - PMIC_nRESET */
+ {OFFSET(mcasp0_fsx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+ /* GPIO3_16 (MCASP0_AXR0) - ETH1_LEDY */
+ {OFFSET(mcasp0_axr0), (MODE(7) | PULLUDDIS) },
+ /* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */
+ {OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) },
+
+ {-1},
+};
+
+static struct module_pin_mux lcd_pin_mux[] = {
+ {OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)}, /* LCD-Data(0) */
+ {OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)}, /* LCD-Data(1) */
+ {OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)}, /* LCD-Data(2) */
+ {OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)}, /* LCD-Data(3) */
+ {OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)}, /* LCD-Data(4) */
+ {OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)}, /* LCD-Data(5) */
+ {OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)}, /* LCD-Data(6) */
+ {OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)}, /* LCD-Data(7) */
+ {OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)}, /* LCD-Data(8) */
+ {OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)}, /* LCD-Data(9) */
+ {OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)}, /* LCD-Data(10) */
+ {OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)}, /* LCD-Data(11) */
+ {OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)}, /* LCD-Data(12) */
+ {OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)}, /* LCD-Data(13) */
+ {OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)}, /* LCD-Data(14) */
+ {OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)}, /* LCD-Data(15) */
+
+ {OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)}, /* LCD-Data(16) */
+ {OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)}, /* LCD-Data(17) */
+ {OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)}, /* LCD-Data(18) */
+ {OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)}, /* LCD-Data(19) */
+ {OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)}, /* LCD-Data(20) */
+ {OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)}, /* LCD-Data(21) */
+ {OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)}, /* LCD-Data(22) */
+ {OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)}, /* LCD-Data(23) */
+
+ {OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)}, /* LCD-VSync */
+ {OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)}, /* LCD-HSync */
+ {OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
+ {OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)}, /* LCD-CLK */
+
+ {-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+ configure_module_pin_mux(mii1_pin_mux);
+ configure_module_pin_mux(mii2_pin_mux);
+#ifdef CONFIG_NAND
+ configure_module_pin_mux(nand_pin_mux);
+#elif defined(CONFIG_MMC)
+ configure_module_pin_mux(mmc1_pin_mux);
+#endif
+ configure_module_pin_mux(spi0_pin_mux);
+ configure_module_pin_mux(lcd_pin_mux);
+ configure_module_pin_mux(gpIOs);
+}
diff --git a/board/ait/cam_enc_4xx/u-boot-spl.lds b/board/ait/cam_enc_4xx/u-boot-spl.lds
index fdfbfc3..c0d09ad 100644
--- a/board/ait/cam_enc_4xx/u-boot-spl.lds
+++ b/board/ait/cam_enc_4xx/u-boot-spl.lds
@@ -48,5 +48,9 @@
} >.sram
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ }
}
diff --git a/board/armltd/integrator/lowlevel_init.S b/board/armltd/integrator/lowlevel_init.S
index 389d5e9..0fb42ad 100644
--- a/board/armltd/integrator/lowlevel_init.S
+++ b/board/armltd/integrator/lowlevel_init.S
@@ -183,7 +183,7 @@
/* Now 0x00000000 is writeable, replace the vectors */
ldr r0, =_start /* r0 <- start of vectors */
- ldr r2, =_TEXT_BASE /* r2 <- past vectors */
+ add r2, r0, #64 /* r2 <- past vectors */
sub r1,r1,r1 /* destination 0x00000000 */
copy_vec:
diff --git a/board/broadcom/bcm28155_ap/Makefile b/board/broadcom/bcm28155_ap/Makefile
new file mode 100644
index 0000000..b18785a
--- /dev/null
+++ b/board/broadcom/bcm28155_ap/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright 2013 Broadcom Corporation.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += $(BOARD).o
diff --git a/board/broadcom/bcm28155_ap/bcm28155_ap.c b/board/broadcom/bcm28155_ap/bcm28155_ap.c
new file mode 100644
index 0000000..940a1c2
--- /dev/null
+++ b/board/broadcom/bcm28155_ap/bcm28155_ap.c
@@ -0,0 +1,87 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/mach-types.h>
+#include <mmc.h>
+#include <asm/kona-common/kona_sdhci.h>
+#include <asm/kona-common/clk.h>
+#include <asm/arch/sysmap.h>
+
+#define SECWATCHDOG_SDOGCR_OFFSET 0x00000000
+#define SECWATCHDOG_SDOGCR_EN_SHIFT 27
+#define SECWATCHDOG_SDOGCR_SRSTEN_SHIFT 26
+#define SECWATCHDOG_SDOGCR_CLKS_SHIFT 20
+#define SECWATCHDOG_SDOGCR_LD_SHIFT 0
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * board_init - early hardware init
+ */
+int board_init(void)
+{
+ printf("Relocation Offset is: %08lx\n", gd->reloc_off);
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ clk_init();
+
+ return 0;
+}
+
+/*
+ * misc_init_r - miscellaneous platform dependent initializations
+ */
+int misc_init_r(void)
+{
+ /* Disable watchdog reset - watchdog unused */
+ writel((0 << SECWATCHDOG_SDOGCR_EN_SHIFT) |
+ (0 << SECWATCHDOG_SDOGCR_SRSTEN_SHIFT) |
+ (4 << SECWATCHDOG_SDOGCR_CLKS_SHIFT) |
+ (0x5a0 << SECWATCHDOG_SDOGCR_LD_SHIFT),
+ (SECWD_BASE_ADDR + SECWATCHDOG_SDOGCR_OFFSET));
+
+ return 0;
+}
+
+/*
+ * dram_init - sets uboots idea of sdram size
+ */
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+ return 0;
+}
+
+/* This is called after dram_init() so use get_ram_size result */
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
+#ifdef CONFIG_KONA_SDHCI
+/*
+ * mmc_init - Initializes mmc
+ */
+int board_mmc_init(bd_t *bis)
+{
+ int ret = 0;
+
+ /* Register eMMC - SDIO2 */
+ ret = kona_sdhci_init(1, 400000, 0);
+ if (ret)
+ return ret;
+
+ /* Register SD Card - SDIO4 kona_mmc_init assumes 0 based index */
+ ret = kona_sdhci_init(3, 400000, 0);
+ return ret;
+}
+#endif
diff --git a/board/cm4008/flash.c b/board/cm4008/flash.c
index 2511928..8315a57 100644
--- a/board/cm4008/flash.c
+++ b/board/cm4008/flash.c
@@ -57,7 +57,7 @@
*/
flash_protect (FLAG_PROTECT_SET,
CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + _bss_start_ofs,
+ CONFIG_SYS_FLASH_BASE + (__bss_end - __bss_start),
&flash_info[0]);
return size;
diff --git a/board/cm41xx/flash.c b/board/cm41xx/flash.c
index 2511928..8315a57 100644
--- a/board/cm41xx/flash.c
+++ b/board/cm41xx/flash.c
@@ -57,7 +57,7 @@
*/
flash_protect (FLAG_PROTECT_SET,
CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + _bss_start_ofs,
+ CONFIG_SYS_FLASH_BASE + (__bss_end - __bss_start),
&flash_info[0]);
return size;
diff --git a/board/compulab/cm_t335/u-boot.lds b/board/compulab/cm_t335/u-boot.lds
index 1b609a2..0984dfe 100644
--- a/board/compulab/cm_t335/u-boot.lds
+++ b/board/compulab/cm_t335/u-boot.lds
@@ -61,7 +61,12 @@
*(.__rel_dyn_end)
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
+
+ _image_binary_end = .;
/*
* Deprecated: this MMU section is used by pxa at present but
@@ -92,10 +97,14 @@
KEEP(*(.__bss_end));
}
- /DISCARD/ : { *(.dynsym) }
- /DISCARD/ : { *(.dynstr*) }
- /DISCARD/ : { *(.dynamic*) }
- /DISCARD/ : { *(.plt*) }
- /DISCARD/ : { *(.interp*) }
- /DISCARD/ : { *(.gnu*) }
+ .dynsym _image_binary_end : { *(.dynsym) }
+ .hash : { *(.hash) }
+ .got.plt : { *(.got.plt) }
+ .dynbss : { *(.dynbss) }
+ .dynstr : { *(.dynstr*) }
+ .dynamic : { *(.dynamic*) }
+ .plt : { *(.plt*) }
+ .interp : { *(.interp*) }
+ .gnu : { *(.gnu*) }
+ .ARM.exidx : { *(.ARM.exidx*) }
}
diff --git a/board/davinci/da8xxevm/u-boot-spl-da850evm.lds b/board/davinci/da8xxevm/u-boot-spl-da850evm.lds
index 5480d1f..de21a13 100644
--- a/board/davinci/da8xxevm/u-boot-spl-da850evm.lds
+++ b/board/davinci/da8xxevm/u-boot-spl-da850evm.lds
@@ -49,5 +49,9 @@
} >.sram
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ }
}
diff --git a/board/davinci/da8xxevm/u-boot-spl-hawk.lds b/board/davinci/da8xxevm/u-boot-spl-hawk.lds
index d49c314..299226b 100644
--- a/board/davinci/da8xxevm/u-boot-spl-hawk.lds
+++ b/board/davinci/da8xxevm/u-boot-spl-hawk.lds
@@ -61,5 +61,8 @@
__bss_end = .;
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
}
diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds
index 1cca176..6da1d4b 100644
--- a/board/freescale/mx31ads/u-boot.lds
+++ b/board/freescale/mx31ads/u-boot.lds
@@ -69,7 +69,12 @@
*(.__rel_dyn_end)
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
+
+ _image_binary_end = .;
/*
* Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
@@ -90,7 +95,7 @@
KEEP(*(.__bss_end));
}
- .dynsym _end : { *(.dynsym) }
+ .dynsym _image_binary_end : { *(.dynsym) }
.dynbss : { *(.dynbss) }
.dynstr : { *(.dynstr*) }
.dynamic : { *(.dynamic*) }
diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
index 703dbec..17c122c 100644
--- a/board/htkw/mcx/mcx.h
+++ b/board/htkw/mcx/mcx.h
@@ -325,8 +325,6 @@
MUX_VAL(CP(SYS_32K), (IEN | PTD | EN | M4)) \
MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) \
MUX_VAL(CP(SYS_NIRQ), (IEN | PTD | EN | M4)) \
- MUX_VAL(CP(SYS_NRESWARM), (IEN | PTU | DIS | M4)) \
- /* SYS_nRESWARM */\
MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) \
MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) \
MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) \
diff --git a/board/mpl/vcma9/lowlevel_init.S b/board/mpl/vcma9/lowlevel_init.S
index b889cf9..cca9c0c 100644
--- a/board/mpl/vcma9/lowlevel_init.S
+++ b/board/mpl/vcma9/lowlevel_init.S
@@ -197,13 +197,10 @@
#define REFCNT_266 0
/**************************************/
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE
-
.globl lowlevel_init
lowlevel_init:
/* use r0 to relocate DATA read/write to flash rather than memory ! */
- ldr r0, _TEXT_BASE
+ ldr r0, =CONFIG_SYS_TEXT_BASE
ldr r13, =BWSCON
/* enable minimal access to PLD */
diff --git a/board/samsung/common/exynos-uboot-spl.lds b/board/samsung/common/exynos-uboot-spl.lds
index 8e3b73e..b22f9e0 100644
--- a/board/samsung/common/exynos-uboot-spl.lds
+++ b/board/samsung/common/exynos-uboot-spl.lds
@@ -42,7 +42,11 @@
. = ALIGN(4);
__image_copy_end = .;
- _end = .;
+
+ .end :
+ {
+ *(.__end)
+ } >.sram
.bss :
{
diff --git a/board/samsung/goni/lowlevel_init.S b/board/samsung/goni/lowlevel_init.S
index 726211a..d52bc09 100644
--- a/board/samsung/goni/lowlevel_init.S
+++ b/board/samsung/goni/lowlevel_init.S
@@ -22,9 +22,6 @@
* r9 has Mobile DDR size, 1 means 1GiB, 2 means 2GiB and so on
*/
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE
-
.globl lowlevel_init
lowlevel_init:
mov r11, lr
diff --git a/board/samsung/smdk2410/lowlevel_init.S b/board/samsung/smdk2410/lowlevel_init.S
index c7b78fd..5de04f1 100644
--- a/board/samsung/smdk2410/lowlevel_init.S
+++ b/board/samsung/smdk2410/lowlevel_init.S
@@ -110,16 +110,13 @@
#define REFCNT 1113 /* period=15.6us, HCLK=60Mhz, (2048+1-15.6*60) */
/**************************************/
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE
-
.globl lowlevel_init
lowlevel_init:
/* memory control configuration */
/* make r0 relative the current location so that it */
/* reads SMRDATA out of FLASH rather than memory ! */
ldr r0, =SMRDATA
- ldr r1, _TEXT_BASE
+ ldr r1, =CONFIG_SYS_TEXT_BASE
sub r0, r0, r1
ldr r1, =BWSCON /* Bus Width Status Controller */
add r2, r0, #13*4
diff --git a/board/samsung/smdkc100/lowlevel_init.S b/board/samsung/smdkc100/lowlevel_init.S
index 4df0974..65e6b7a 100644
--- a/board/samsung/smdkc100/lowlevel_init.S
+++ b/board/samsung/smdkc100/lowlevel_init.S
@@ -17,9 +17,6 @@
* r5 has zero always
*/
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE
-
.globl lowlevel_init
lowlevel_init:
mov r9, lr
diff --git a/board/silica/pengwyn/Makefile b/board/silica/pengwyn/Makefile
new file mode 100644
index 0000000..c8b4f9a
--- /dev/null
+++ b/board/silica/pengwyn/Makefile
@@ -0,0 +1,13 @@
+#
+# Makefile
+#
+# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_NOR_BOOT),y)
+obj-y := mux.o
+endif
+
+obj-y += board.o
diff --git a/board/silica/pengwyn/board.c b/board/silica/pengwyn/board.c
new file mode 100644
index 0000000..a553129
--- /dev/null
+++ b/board/silica/pengwyn/board.c
@@ -0,0 +1,207 @@
+/*
+ * board.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <phy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+#if defined(CONFIG_SPL_BUILD)
+
+/* DDR3 RAM timings */
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41K128MJT187E_RD_DQS,
+ .datawdsratio0 = MT41K128MJT187E_WR_DQS,
+ .datafwsratio0 = MT41K128MJT187E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41K128MJT187E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41K128MJT187E_RATIO,
+ .cmd0iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+ .cmd1csratio = MT41K128MJT187E_RATIO,
+ .cmd1iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+ .cmd2csratio = MT41K128MJT187E_RATIO,
+ .cmd2iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41K128MJT187E_EMIF_SDCFG,
+ .ref_ctrl = MT41K128MJT187E_EMIF_SDREF,
+ .sdram_tim1 = MT41K128MJT187E_EMIF_TIM1,
+ .sdram_tim2 = MT41K128MJT187E_EMIF_TIM2,
+ .sdram_tim3 = MT41K128MJT187E_EMIF_TIM3,
+ .zq_config = MT41K128MJT187E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41K128MJT187E_EMIF_READ_LATENCY |
+ PHY_EN_DYN_PWRDN,
+};
+
+const struct ctrl_ioregs ddr3_ioregs = {
+ .cm0ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .cm1ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .cm2ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .dt0ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+ .dt1ioctl = MT41K128MJT187E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+ /* break into full u-boot on 'c' */
+ return serial_tstc() && serial_getc() == 'c';
+}
+#endif
+
+#define OSC (V_OSCK/1000000)
+const struct dpll_params dpll_ddr_266 = {
+ 266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_303 = {
+ 303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_400 = {
+ 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ /*
+ * The pengwyn board uses the TPS650250 PMIC without I2C
+ * interface and will output the following fixed voltages:
+ * DCDC1=3V3 (IO) DCDC2=1V5 (DDR) DCDC3=1V26 (Vmpu)
+ * VLDO1=1V8 (IO) VLDO2=1V8(IO)
+ * Vcore=1V1 is fixed, generated by TPS62231
+ */
+
+ /* Get the frequency */
+ dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* 720MHz cpu, this might change on newer board revisions */
+ dpll_mpu_opp100.m = MPUPLL_M_720;
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ /* future configs can return other clock settings */
+ return &dpll_ddr_303;
+}
+
+void set_uart_mux_conf(void)
+{
+ enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+ enable_board_pin_mux();
+}
+
+void sdram_init(void)
+{
+ config_ddr(303, &ddr3_ioregs, &ddr3_data,
+ &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+}
+#endif /* if CONFIG_SPL_BUILD */
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+ gpmc_init();
+ return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+ return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_id = 0,
+ .phy_if = PHY_INTERFACE_MODE_MII,
+ },
+ {
+ .slave_reg_ofs = 0x308,
+ .sliver_reg_ofs = 0xdc0,
+ .phy_id = 1,
+ .phy_if = PHY_INTERFACE_MODE_MII,
+ },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+ int rv, n = 0;
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+
+ if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+ printf("<ethaddr> not set. Reading from E-fuse\n");
+ /* try reading mac address from efuse */
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+ if (is_valid_ether_addr(mac_addr))
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ else
+ return n;
+ }
+
+ writel(MII_MODE_ENABLE, &cdev->miisel);
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0)
+ printf("Error %d registering CPSW switch\n", rv);
+ else
+ n += rv;
+ return n;
+}
+#endif /* if CONFIG_DRIVER_TI_CPSW */
diff --git a/board/silica/pengwyn/board.h b/board/silica/pengwyn/board.h
new file mode 100644
index 0000000..05addf6
--- /dev/null
+++ b/board/silica/pengwyn/board.h
@@ -0,0 +1,15 @@
+/*
+ * board.h
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+void enable_uart0_pin_mux(void);
+void enable_board_pin_mux(void);
+
+#endif
diff --git a/board/silica/pengwyn/mux.c b/board/silica/pengwyn/mux.c
new file mode 100644
index 0000000..c8be440
--- /dev/null
+++ b/board/silica/pengwyn/mux.c
@@ -0,0 +1,98 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include "board.h"
+
+/* UART0 pins E15(rx),E16(tx) [E17(rts),E18(cts)] */
+static struct module_pin_mux uart0_pin_mux[] = {
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */
+ {-1},
+};
+
+/* unused: UART1 pins D15(tx),D16(rx),D17(cts),D18(rts) */
+
+/* I2C pins C16(scl)/C17(sda) */
+static struct module_pin_mux i2c0_pin_mux[] = {
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C0_DATA */
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C0_SCLK */
+ {-1},
+};
+
+/* MMC0 pins */
+static struct module_pin_mux mmc0_pin_mux[] = {
+ {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
+ {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
+ {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
+ {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
+ {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */
+ {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */
+ {OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */
+ {-1},
+};
+
+/* MII pins */
+static struct module_pin_mux mii1_pin_mux[] = {
+ {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */
+ {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */
+ {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */
+ {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */
+ {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */
+ {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */
+ {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */
+ {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */
+ {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */
+ {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */
+ {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */
+ {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */
+ {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {-1},
+};
+
+/* NAND pins */
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
+ {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
+ {-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_board_pin_mux()
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+ configure_module_pin_mux(uart0_pin_mux);
+ configure_module_pin_mux(mii1_pin_mux);
+ configure_module_pin_mux(mmc0_pin_mux);
+ configure_module_pin_mux(nand_pin_mux);
+}
diff --git a/board/ti/am335x/u-boot.lds b/board/ti/am335x/u-boot.lds
index 6a734b3..ceb2022 100644
--- a/board/ti/am335x/u-boot.lds
+++ b/board/ti/am335x/u-boot.lds
@@ -77,7 +77,12 @@
*(.__rel_dyn_end)
}
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
+
+ _image_binary_end = .;
/*
* Deprecated: this MMU section is used by pxa at present but
@@ -108,7 +113,7 @@
KEEP(*(.__bss_end));
}
- .dynsym _end : { *(.dynsym) }
+ .dynsym _image_binary_end : { *(.dynsym) }
.dynbss : { *(.dynbss) }
.dynstr : { *(.dynstr*) }
.dynamic : { *(.dynamic*) }
diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c
index 4e6846a..95fd137 100644
--- a/board/ti/am43xx/board.c
+++ b/board/ti/am43xx/board.c
@@ -346,14 +346,14 @@
u32 temp;
/* enable module */
- writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO0_BASE + OMAP_GPIO_CTRL);
+ writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO5_BASE + OMAP_GPIO_CTRL);
- /* enable output for GPIO0_22 */
- writel(GPIO_SETDATAOUT(GPIO_22),
- AM33XX_GPIO0_BASE + OMAP_GPIO_SETDATAOUT);
- temp = readl(AM33XX_GPIO0_BASE + OMAP_GPIO_OE);
- temp = temp & ~(GPIO_OE_ENABLE(GPIO_22));
- writel(temp, AM33XX_GPIO0_BASE + OMAP_GPIO_OE);
+ /* enable output for GPIO5_7 */
+ writel(GPIO_SETDATAOUT(7),
+ AM33XX_GPIO5_BASE + OMAP_GPIO_SETDATAOUT);
+ temp = readl(AM33XX_GPIO5_BASE + OMAP_GPIO_OE);
+ temp = temp & ~(GPIO_OE_ENABLE(7));
+ writel(temp, AM33XX_GPIO5_BASE + OMAP_GPIO_OE);
}
void sdram_init(void)
diff --git a/board/ti/am43xx/mux.c b/board/ti/am43xx/mux.c
index f96c56f..c330a81 100644
--- a/board/ti/am43xx/mux.c
+++ b/board/ti/am43xx/mux.c
@@ -33,8 +33,8 @@
{-1},
};
-static struct module_pin_mux gpio0_22_pin_mux[] = {
- {OFFSET(ddr_ba2), (MODE(9) | PULLUP_EN)}, /* GPIO0_22 */
+static struct module_pin_mux gpio5_7_pin_mux[] = {
+ {OFFSET(spi0_cs0), (MODE(7) | PULLUP_EN)}, /* GPIO5_7 */
{-1},
};
@@ -59,7 +59,7 @@
configure_module_pin_mux(i2c0_pin_mux);
if (board_is_gpevm())
- configure_module_pin_mux(gpio0_22_pin_mux);
+ configure_module_pin_mux(gpio5_7_pin_mux);
configure_module_pin_mux(qspi_pin_mux);
}
diff --git a/board/ti/omap5912osk/lowlevel_init.S b/board/ti/omap5912osk/lowlevel_init.S
index cad0a5a..e05a1c7 100644
--- a/board/ti/omap5912osk/lowlevel_init.S
+++ b/board/ti/omap5912osk/lowlevel_init.S
@@ -18,10 +18,6 @@
#include <./configs/omap1510.h>
#endif
-
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */
-
.globl lowlevel_init
lowlevel_init:
diff --git a/board/vpac270/u-boot-spl.lds b/board/vpac270/u-boot-spl.lds
index b6fdde4..5dbf94e 100644
--- a/board/vpac270/u-boot-spl.lds
+++ b/board/vpac270/u-boot-spl.lds
@@ -54,7 +54,12 @@
. = ALIGN(0x800);
- _end = .;
+ .end :
+ {
+ *(.__end)
+ }
+
+ _image_binary_end = .;
.bss __rel_dyn_start (OVERLAY) : {
__bss_start = .;
@@ -63,7 +68,7 @@
__bss_end = .;
}
- .dynsym _end : { *(.dynsym) }
+ .dynsym _image_binary_end : { *(.dynsym) }
.dynbss : { *(.dynbss) }
.dynstr : { *(.dynstr*) }
.dynamic : { *(.dynamic*) }
diff --git a/boards.cfg b/boards.cfg
index a0dda1b..d28e09b 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -259,6 +259,11 @@
Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <r.meier@siemens.com>
Active arm armv7 am33xx siemens pxm2 pxm2 - Roger Meier <r.meier@siemens.com>
Active arm armv7 am33xx siemens rut rut - Roger Meier <r.meier@siemens.com>
+Active arm armv7 am33xx silica pengwyn pengwyn - Lothar Felten <lothar.felten@gmail.com>
+Active arm armv7 am33xx BuR tseries tseries_nand tseries:SERIAL1,CONS_INDEX=1,NAND Hannes Petermaier <hannes.petermaier@br-automation.com>
+Active arm armv7 am33xx BuR tseries tseries_mmc tseries:SERIAL1,CONS_INDEX=1,EMMC_BOOT Hannes Petermaier <hannes.petermaier@br-automation.com>
+Active arm armv7 am33xx BuR tseries tseries_spi tseries:SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT Hannes Petermaier <hannes.petermaier@br-automation.com>
+Active arm armv7 am33xx BuR kwb kwb kwb:SERIAL1,CONS_INDEX=1 Hannes Petermaier <hannes.petermaier@br-automation.com>
Active arm armv7 am33xx ti am335x am335x_boneblack am335x_evm:SERIAL1,CONS_INDEX=1,EMMC_BOOT Tom Rini <trini@ti.com>
Active arm armv7 am33xx ti am335x am335x_evm am335x_evm:SERIAL1,CONS_INDEX=1,NAND Tom Rini <trini@ti.com>
Active arm armv7 am33xx ti am335x am335x_evm_nor am335x_evm:SERIAL1,CONS_INDEX=1,NAND,NOR Tom Rini <trini@ti.com>
@@ -276,6 +281,7 @@
Active arm armv7 at91 atmel sama5d3xek sama5d3xek_mmc sama5d3xek:SAMA5D3,SYS_USE_MMC Bo Shen <voice.shen@atmel.com>
Active arm armv7 at91 atmel sama5d3xek sama5d3xek_nandflash sama5d3xek:SAMA5D3,SYS_USE_NANDFLASH Bo Shen <voice.shen@atmel.com>
Active arm armv7 at91 atmel sama5d3xek sama5d3xek_spiflash sama5d3xek:SAMA5D3,SYS_USE_SERIALFLASH Bo Shen <voice.shen@atmel.com>
+Active arm armv7 bcm281xx broadcom bcm28155_ap bcm28155_ap bcm28155_ap Tim Kryger <tim.kryger@linaro.org>
Active arm armv7 exynos samsung arndale arndale - Inderpal Singh <inderpal.singh@linaro.org>
Active arm armv7 exynos samsung origen origen - Chander Kashyap <k.chander@samsung.com>
Active arm armv7 exynos samsung smdk5250 smdk5250 - Chander Kashyap <k.chander@samsung.com>
diff --git a/common/Makefile b/common/Makefile
index 6652ad4..ca9af13 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -238,5 +238,3 @@
obj-y += stdio.o
CFLAGS_env_embedded.o := -Wa,--no-warn -DENV_CRC=$(shell tools/envcrc 2>/dev/null)
-CFLAGS_hush.o := $(PLATFORM_NO_UNALIGNED)
-CFLAGS_fdt_support.o := $(PLATFORM_NO_UNALIGNED)
diff --git a/common/board_f.c b/common/board_f.c
index a973b95..e591a0e 100644
--- a/common/board_f.c
+++ b/common/board_f.c
@@ -149,13 +149,9 @@
#ifndef CONFIG_SANDBOX
ulong bss_start, bss_end;
-#ifdef CONFIG_SYS_SYM_OFFSETS
- bss_start = _bss_start_ofs + _TEXT_BASE;
- bss_end = _bss_end_ofs + _TEXT_BASE;
-#else
bss_start = (ulong)&__bss_start;
bss_end = (ulong)&__bss_end;
-#endif
+
debug("U-Boot code: %08X -> %08lX BSS: -> %08lX\n",
CONFIG_SYS_TEXT_BASE, bss_start, bss_end);
#endif
@@ -268,8 +264,8 @@
static int setup_mon_len(void)
{
-#ifdef CONFIG_SYS_SYM_OFFSETS
- gd->mon_len = _bss_end_ofs;
+#ifdef __ARM__
+ gd->mon_len = (ulong)&__bss_end - (ulong)_start;
#elif defined(CONFIG_SANDBOX)
gd->mon_len = (ulong)&_end - (ulong)_init;
#else
@@ -352,11 +348,7 @@
gd->fdt_blob = __dtb_dt_begin;
#elif defined CONFIG_OF_SEPARATE
/* FDT is at end of image */
-# ifdef CONFIG_SYS_SYM_OFFSETS
- gd->fdt_blob = (void *)(_end_ofs + CONFIG_SYS_TEXT_BASE);
-# else
gd->fdt_blob = (ulong *)&_end;
-# endif
#elif defined(CONFIG_OF_HOSTFILE)
if (read_fdt_from_file()) {
puts("Failed to read control FDT\n");
diff --git a/common/board_r.c b/common/board_r.c
index c2d0763..899f377 100644
--- a/common/board_r.c
+++ b/common/board_r.c
@@ -128,8 +128,8 @@
static int initr_reloc_global_data(void)
{
-#ifdef CONFIG_SYS_SYM_OFFSETS
- monitor_flash_len = _end_ofs;
+#ifdef __ARM__
+ monitor_flash_len = _end - __image_copy_start;
#elif !defined(CONFIG_SANDBOX)
monitor_flash_len = (ulong)&__init_end - gd->relocaddr;
#endif
diff --git a/common/cmd_pxe.c b/common/cmd_pxe.c
index 6aabd13..3483328 100644
--- a/common/cmd_pxe.c
+++ b/common/cmd_pxe.c
@@ -45,6 +45,7 @@
return ret;
}
+#ifdef CONFIG_CMD_NET
/*
* Convert an ethaddr from the environment to the format used by pxelinux
* filenames based on mac addresses. Convert's ':' to '-', and adds "01-" to
@@ -75,6 +76,7 @@
return 1;
}
+#endif
/*
* Returns the directory the file specified in the bootfile env variable is
@@ -120,6 +122,7 @@
static int (*do_getfile)(cmd_tbl_t *cmdtp, const char *file_path, char *file_addr);
+#ifdef CONFIG_CMD_NET
static int do_get_tftp(cmd_tbl_t *cmdtp, const char *file_path, char *file_addr)
{
char *tftp_argv[] = {"tftp", NULL, NULL, NULL};
@@ -132,6 +135,7 @@
return 1;
}
+#endif
static char *fs_argv[5];
@@ -249,6 +253,8 @@
return 1;
}
+#ifdef CONFIG_CMD_NET
+
#define PXELINUX_DIR "pxelinux.cfg/"
/*
@@ -397,6 +403,7 @@
return 1;
}
+#endif
/*
* Wrapper to make it easier to store the file at file_path in the location
@@ -647,6 +654,7 @@
len += strlen(ip_str);
}
+#ifdef CONFIG_CMD_NET
if (label->ipappend & 0x2) {
int err;
strcpy(mac_str, " BOOTIF=");
@@ -655,6 +663,7 @@
mac_str[0] = '\0';
len += strlen(mac_str);
}
+#endif
if (label->append)
len += strlen(label->append);
@@ -1503,6 +1512,7 @@
boot_unattempted_labels(cmdtp, cfg);
}
+#ifdef CONFIG_CMD_NET
/*
* Boots a system using a pxe file
*
@@ -1579,6 +1589,7 @@
"get - try to retrieve a pxe file using tftp\npxe "
"boot [pxefile_addr_r] - boot from the pxe file at pxefile_addr_r\n"
);
+#endif
/*
* Boots a system using a local disk syslinux/extlinux file
diff --git a/doc/README.arm-unaligned-accesses b/doc/README.arm-unaligned-accesses
deleted file mode 100644
index c37d135..0000000
--- a/doc/README.arm-unaligned-accesses
+++ /dev/null
@@ -1,122 +0,0 @@
-If you are reading this because of a data abort: the following MIGHT
-be relevant to your abort, if it was caused by an alignment violation.
-In order to determine this, use the PC from the abort dump along with
-an objdump -s -S of the u-boot ELF binary to locate the function where
-the abort happened; then compare this function with the examples below.
-If they match, then you've been hit with a compiler generated unaligned
-access, and you should rewrite your code or add -mno-unaligned-access
-to the command line of the offending file.
-
-Note that the PC shown in the abort message is relocated. In order to
-be able to match it to an address in the ELF binary dump, you will need
-to know the relocation offset. If your target defines CONFIG_CMD_BDI
-and if you can get to the prompt and enter commands before the abort
-happens, then command "bdinfo" will give you the offset. Otherwise you
-will need to try a build with DEBUG set, which will display the offset,
-or use a debugger and set a breakpoint at relocate_code() to see the
-offset (passed as an argument).
-
-*
-
-Since U-Boot runs on a variety of hardware, some only able to perform
-unaligned accesses with a strong penalty, some unable to perform them
-at all, the policy regarding unaligned accesses is to not perform any,
-unless absolutely necessary because of hardware or standards.
-
-Also, on hardware which permits it, the core is configured to throw
-data abort exceptions on unaligned accesses in order to catch these
-unallowed accesses as early as possible.
-
-Until version 4.7, the gcc default for performing unaligned accesses
-(-mno-unaligned-access) is to emulate unaligned accesses using aligned
-loads and stores plus shifts and masks. Emulated unaligned accesses
-will not be caught by hardware. These accesses may be costly and may
-be actually unnecessary. In order to catch these accesses and remove
-or optimize them, option -munaligned-access is explicitly set for all
-versions of gcc which support it.
-
-From gcc 4.7 onward starting at armv7 architectures, the default for
-performing unaligned accesses is to use unaligned native loads and
-stores (-munaligned-access), because the cost of unaligned accesses
-has dropped on armv7 and beyond. This should not affect U-Boot's
-policy of controlling unaligned accesses, however the compiler may
-generate uncontrolled unaligned accesses on its own in at least one
-known case: when declaring a local initialized char array, e.g.
-
-function foo()
-{
- char buffer[] = "initial value";
-/* or */
- char buffer[] = { 'i', 'n', 'i', 't', 0 };
- ...
-}
-
-Under -munaligned-accesses with optimizations on, this declaration
-causes the compiler to generate native loads from the literal string
-and native stores to the buffer, and the literal string alignment
-cannot be controlled. If it is misaligned, then the core will throw
-a data abort exception.
-
-Quite probably the same might happen for 16-bit array initializations
-where the constant is aligned on a boundary which is a multiple of 2
-but not of 4:
-
-function foo()
-{
- u16 buffer[] = { 1, 2, 3 };
- ...
-}
-
-The long term solution to this issue is to add an option to gcc to
-allow controlling the general alignment of data, including constant
-initialization values.
-
-However this will only apply to the version of gcc which will have such
-an option. For other versions, there are four workarounds:
-
-a) Enforce as a rule that array initializations as described above
- are forbidden. This is generally not acceptable as they are valid,
- and usual, C constructs. The only case where they could be rejected
- is when they actually equate to a const char* declaration, i.e. the
- array is initialized and never modified in the function's scope.
-
-b) Drop the requirement on unaligned accesses at least for ARMv7,
- i.e. do not throw a data abort exception upon unaligned accesses.
- But that will allow adding badly aligned code to U-Boot, only for
- it to fail when re-used with a stricter target, possibly once the
- bad code is already in mainline.
-
-c) Relax the -munaligned-access rule globally. This will prevent native
- unaligned accesses of course, but that will also hide any bug caused
- by a bad unaligned access, making it much harder to diagnose it. It
- is actually what already happens when building ARM targets with a
- pre-4.7 gcc, and it may actually already hide some bugs yet unseen
- until the target gets compiled with -munaligned-access.
-
-d) Relax the -munaligned-access rule only for for files susceptible to
- the local initialized array issue and for armv7 architectures and
- beyond. This minimizes the quantity of code which can hide unwanted
- misaligned accesses.
-
-The option retained is d).
-
-Considering that actual occurrences of the issue are rare (as of this
-writing, 5 files out of 7840 in U-Boot, or .3%, contain an initialized
-local char array which cannot actually be replaced with a const char*),
-contributors should not be required to systematically try and detect
-the issue in their patches.
-
-Detecting files susceptible to the issue can be automated through a
-filter installed as a hook in .git which recognizes local char array
-initializations. Automation should err on the false positive side, for
-instance flagging non-local arrays as if they were local if they cannot
-be told apart.
-
-In any case, detection shall not prevent committing the patch, but
-shall pre-populate the commit message with a note to the effect that
-this patch contains an initialized local char or 16-bit array and thus
-should be protected from the gcc 4.7 issue.
-
-Upon a positive detection, either $(PLATFORM_NO_UNALIGNED) should be
-added to CFLAGS for the affected file(s), or if the array is a pseudo
-const char*, it should be replaced by an actual one.
diff --git a/doc/README.unaligned-memory-access.txt b/doc/README.unaligned-memory-access.txt
new file mode 100644
index 0000000..00529f5
--- /dev/null
+++ b/doc/README.unaligned-memory-access.txt
@@ -0,0 +1,240 @@
+Editors note: This document is _heavily_ cribbed from the Linux Kernel, with
+really only the section about "Alignment vs. Networking" removed.
+
+UNALIGNED MEMORY ACCESSES
+=========================
+
+Linux runs on a wide variety of architectures which have varying behaviour
+when it comes to memory access. This document presents some details about
+unaligned accesses, why you need to write code that doesn't cause them,
+and how to write such code!
+
+
+The definition of an unaligned access
+=====================================
+
+Unaligned memory accesses occur when you try to read N bytes of data starting
+from an address that is not evenly divisible by N (i.e. addr % N != 0).
+For example, reading 4 bytes of data from address 0x10004 is fine, but
+reading 4 bytes of data from address 0x10005 would be an unaligned memory
+access.
+
+The above may seem a little vague, as memory access can happen in different
+ways. The context here is at the machine code level: certain instructions read
+or write a number of bytes to or from memory (e.g. movb, movw, movl in x86
+assembly). As will become clear, it is relatively easy to spot C statements
+which will compile to multiple-byte memory access instructions, namely when
+dealing with types such as u16, u32 and u64.
+
+
+Natural alignment
+=================
+
+The rule mentioned above forms what we refer to as natural alignment:
+When accessing N bytes of memory, the base memory address must be evenly
+divisible by N, i.e. addr % N == 0.
+
+When writing code, assume the target architecture has natural alignment
+requirements.
+
+In reality, only a few architectures require natural alignment on all sizes
+of memory access. However, we must consider ALL supported architectures;
+writing code that satisfies natural alignment requirements is the easiest way
+to achieve full portability.
+
+
+Why unaligned access is bad
+===========================
+
+The effects of performing an unaligned memory access vary from architecture
+to architecture. It would be easy to write a whole document on the differences
+here; a summary of the common scenarios is presented below:
+
+ - Some architectures are able to perform unaligned memory accesses
+ transparently, but there is usually a significant performance cost.
+ - Some architectures raise processor exceptions when unaligned accesses
+ happen. The exception handler is able to correct the unaligned access,
+ at significant cost to performance.
+ - Some architectures raise processor exceptions when unaligned accesses
+ happen, but the exceptions do not contain enough information for the
+ unaligned access to be corrected.
+ - Some architectures are not capable of unaligned memory access, but will
+ silently perform a different memory access to the one that was requested,
+ resulting in a subtle code bug that is hard to detect!
+
+It should be obvious from the above that if your code causes unaligned
+memory accesses to happen, your code will not work correctly on certain
+platforms and will cause performance problems on others.
+
+
+Code that does not cause unaligned access
+=========================================
+
+At first, the concepts above may seem a little hard to relate to actual
+coding practice. After all, you don't have a great deal of control over
+memory addresses of certain variables, etc.
+
+Fortunately things are not too complex, as in most cases, the compiler
+ensures that things will work for you. For example, take the following
+structure:
+
+ struct foo {
+ u16 field1;
+ u32 field2;
+ u8 field3;
+ };
+
+Let us assume that an instance of the above structure resides in memory
+starting at address 0x10000. With a basic level of understanding, it would
+not be unreasonable to expect that accessing field2 would cause an unaligned
+access. You'd be expecting field2 to be located at offset 2 bytes into the
+structure, i.e. address 0x10002, but that address is not evenly divisible
+by 4 (remember, we're reading a 4 byte value here).
+
+Fortunately, the compiler understands the alignment constraints, so in the
+above case it would insert 2 bytes of padding in between field1 and field2.
+Therefore, for standard structure types you can always rely on the compiler
+to pad structures so that accesses to fields are suitably aligned (assuming
+you do not cast the field to a type of different length).
+
+Similarly, you can also rely on the compiler to align variables and function
+parameters to a naturally aligned scheme, based on the size of the type of
+the variable.
+
+At this point, it should be clear that accessing a single byte (u8 or char)
+will never cause an unaligned access, because all memory addresses are evenly
+divisible by one.
+
+On a related topic, with the above considerations in mind you may observe
+that you could reorder the fields in the structure in order to place fields
+where padding would otherwise be inserted, and hence reduce the overall
+resident memory size of structure instances. The optimal layout of the
+above example is:
+
+ struct foo {
+ u32 field2;
+ u16 field1;
+ u8 field3;
+ };
+
+For a natural alignment scheme, the compiler would only have to add a single
+byte of padding at the end of the structure. This padding is added in order
+to satisfy alignment constraints for arrays of these structures.
+
+Another point worth mentioning is the use of __attribute__((packed)) on a
+structure type. This GCC-specific attribute tells the compiler never to
+insert any padding within structures, useful when you want to use a C struct
+to represent some data that comes in a fixed arrangement 'off the wire'.
+
+You might be inclined to believe that usage of this attribute can easily
+lead to unaligned accesses when accessing fields that do not satisfy
+architectural alignment requirements. However, again, the compiler is aware
+of the alignment constraints and will generate extra instructions to perform
+the memory access in a way that does not cause unaligned access. Of course,
+the extra instructions obviously cause a loss in performance compared to the
+non-packed case, so the packed attribute should only be used when avoiding
+structure padding is of importance.
+
+
+Code that causes unaligned access
+=================================
+
+With the above in mind, let's move onto a real life example of a function
+that can cause an unaligned memory access. The following function taken
+from the Linux Kernel's include/linux/etherdevice.h is an optimized routine
+to compare two ethernet MAC addresses for equality.
+
+bool ether_addr_equal(const u8 *addr1, const u8 *addr2)
+{
+#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+ u32 fold = ((*(const u32 *)addr1) ^ (*(const u32 *)addr2)) |
+ ((*(const u16 *)(addr1 + 4)) ^ (*(const u16 *)(addr2 + 4)));
+
+ return fold == 0;
+#else
+ const u16 *a = (const u16 *)addr1;
+ const u16 *b = (const u16 *)addr2;
+ return ((a[0] ^ b[0]) | (a[1] ^ b[1]) | (a[2] ^ b[2])) != 0;
+#endif
+}
+
+In the above function, when the hardware has efficient unaligned access
+capability, there is no issue with this code. But when the hardware isn't
+able to access memory on arbitrary boundaries, the reference to a[0] causes
+2 bytes (16 bits) to be read from memory starting at address addr1.
+
+Think about what would happen if addr1 was an odd address such as 0x10003.
+(Hint: it'd be an unaligned access.)
+
+Despite the potential unaligned access problems with the above function, it
+is included in the kernel anyway but is understood to only work normally on
+16-bit-aligned addresses. It is up to the caller to ensure this alignment or
+not use this function at all. This alignment-unsafe function is still useful
+as it is a decent optimization for the cases when you can ensure alignment,
+which is true almost all of the time in ethernet networking context.
+
+
+Here is another example of some code that could cause unaligned accesses:
+ void myfunc(u8 *data, u32 value)
+ {
+ [...]
+ *((u32 *) data) = cpu_to_le32(value);
+ [...]
+ }
+
+This code will cause unaligned accesses every time the data parameter points
+to an address that is not evenly divisible by 4.
+
+In summary, the 2 main scenarios where you may run into unaligned access
+problems involve:
+ 1. Casting variables to types of different lengths
+ 2. Pointer arithmetic followed by access to at least 2 bytes of data
+
+
+Avoiding unaligned accesses
+===========================
+
+The easiest way to avoid unaligned access is to use the get_unaligned() and
+put_unaligned() macros provided by the <asm/unaligned.h> header file.
+
+Going back to an earlier example of code that potentially causes unaligned
+access:
+
+ void myfunc(u8 *data, u32 value)
+ {
+ [...]
+ *((u32 *) data) = cpu_to_le32(value);
+ [...]
+ }
+
+To avoid the unaligned memory access, you would rewrite it as follows:
+
+ void myfunc(u8 *data, u32 value)
+ {
+ [...]
+ value = cpu_to_le32(value);
+ put_unaligned(value, (u32 *) data);
+ [...]
+ }
+
+The get_unaligned() macro works similarly. Assuming 'data' is a pointer to
+memory and you wish to avoid unaligned access, its usage is as follows:
+
+ u32 value = get_unaligned((u32 *) data);
+
+These macros work for memory accesses of any length (not just 32 bits as
+in the examples above). Be aware that when compared to standard access of
+aligned memory, using these macros to access unaligned memory can be costly in
+terms of performance.
+
+If use of such macros is not convenient, another option is to use memcpy(),
+where the source or destination (or both) are of type u8* or unsigned char*.
+Due to the byte-wise nature of this operation, unaligned accesses are avoided.
+
+--
+In the Linux Kernel,
+Authors: Daniel Drake <dsd@gentoo.org>,
+ Johannes Berg <johannes@sipsolutions.net>
+With help from: Alan Cox, Avuton Olrich, Heikki Orsila, Jan Engelhardt,
+Kyle McMartin, Kyle Moffett, Randy Dunlap, Robert Hancock, Uli Kunitz,
+Vadim Lobanov
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index b903c45..ed2c0c7 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -8,6 +8,7 @@
obj-$(CONFIG_AT91_GPIO) += at91_gpio.o
obj-$(CONFIG_INTEL_ICH6_GPIO) += intel_ich6_gpio.o
obj-$(CONFIG_KIRKWOOD_GPIO) += kw_gpio.o
+obj-$(CONFIG_KONA_GPIO) += kona_gpio.o
obj-$(CONFIG_MARVELL_GPIO) += mvgpio.o
obj-$(CONFIG_MARVELL_MFP) += mvmfp.o
obj-$(CONFIG_MXC_GPIO) += mxc_gpio.o
diff --git a/drivers/gpio/kona_gpio.c b/drivers/gpio/kona_gpio.c
new file mode 100644
index 0000000..6511743
--- /dev/null
+++ b/drivers/gpio/kona_gpio.c
@@ -0,0 +1,141 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sysmap.h>
+
+#define GPIO_BASE (void *)GPIO2_BASE_ADDR
+
+#define GPIO_PASSWD 0x00a5a501
+#define GPIO_PER_BANK 32
+#define GPIO_MAX_BANK_NUM 8
+
+#define GPIO_BANK(gpio) ((gpio) >> 5)
+#define GPIO_BITMASK(gpio) \
+ (1UL << ((gpio) & (GPIO_PER_BANK - 1)))
+
+#define GPIO_OUT_STATUS(bank) (0x00000000 + ((bank) << 2))
+#define GPIO_IN_STATUS(bank) (0x00000020 + ((bank) << 2))
+#define GPIO_OUT_SET(bank) (0x00000040 + ((bank) << 2))
+#define GPIO_OUT_CLEAR(bank) (0x00000060 + ((bank) << 2))
+#define GPIO_INT_STATUS(bank) (0x00000080 + ((bank) << 2))
+#define GPIO_INT_MASK(bank) (0x000000a0 + ((bank) << 2))
+#define GPIO_INT_MSKCLR(bank) (0x000000c0 + ((bank) << 2))
+#define GPIO_CONTROL(bank) (0x00000100 + ((bank) << 2))
+#define GPIO_PWD_STATUS(bank) (0x00000500 + ((bank) << 2))
+
+#define GPIO_GPPWR_OFFSET 0x00000520
+
+#define GPIO_GPCTR0_DBR_SHIFT 5
+#define GPIO_GPCTR0_DBR_MASK 0x000001e0
+
+#define GPIO_GPCTR0_ITR_SHIFT 3
+#define GPIO_GPCTR0_ITR_MASK 0x00000018
+#define GPIO_GPCTR0_ITR_CMD_RISING_EDGE 0x00000001
+#define GPIO_GPCTR0_ITR_CMD_FALLING_EDGE 0x00000002
+#define GPIO_GPCTR0_ITR_CMD_BOTH_EDGE 0x00000003
+
+#define GPIO_GPCTR0_IOTR_MASK 0x00000001
+#define GPIO_GPCTR0_IOTR_CMD_0UTPUT 0x00000000
+#define GPIO_GPCTR0_IOTR_CMD_INPUT 0x00000001
+
+int gpio_request(unsigned gpio, const char *label)
+{
+ unsigned int value, off;
+
+ writel(GPIO_PASSWD, GPIO_BASE + GPIO_GPPWR_OFFSET);
+ off = GPIO_PWD_STATUS(GPIO_BANK(gpio));
+ value = readl(GPIO_BASE + off) & ~GPIO_BITMASK(gpio);
+ writel(value, GPIO_BASE + off);
+
+ return 0;
+}
+
+int gpio_free(unsigned gpio)
+{
+ unsigned int value, off;
+
+ writel(GPIO_PASSWD, GPIO_BASE + GPIO_GPPWR_OFFSET);
+ off = GPIO_PWD_STATUS(GPIO_BANK(gpio));
+ value = readl(GPIO_BASE + off) | GPIO_BITMASK(gpio);
+ writel(value, GPIO_BASE + off);
+
+ return 0;
+}
+
+int gpio_direction_input(unsigned gpio)
+{
+ u32 val;
+
+ val = readl(GPIO_BASE + GPIO_CONTROL(gpio));
+ val &= ~GPIO_GPCTR0_IOTR_MASK;
+ val |= GPIO_GPCTR0_IOTR_CMD_INPUT;
+ writel(val, GPIO_BASE + GPIO_CONTROL(gpio));
+
+ return 0;
+}
+
+int gpio_direction_output(unsigned gpio, int value)
+{
+ int bank_id = GPIO_BANK(gpio);
+ int bitmask = GPIO_BITMASK(gpio);
+ u32 val, off;
+
+ val = readl(GPIO_BASE + GPIO_CONTROL(gpio));
+ val &= ~GPIO_GPCTR0_IOTR_MASK;
+ val |= GPIO_GPCTR0_IOTR_CMD_0UTPUT;
+ writel(val, GPIO_BASE + GPIO_CONTROL(gpio));
+ off = value ? GPIO_OUT_SET(bank_id) : GPIO_OUT_CLEAR(bank_id);
+
+ val = readl(GPIO_BASE + off);
+ val |= bitmask;
+ writel(val, GPIO_BASE + off);
+
+ return 0;
+}
+
+int gpio_get_value(unsigned gpio)
+{
+ int bank_id = GPIO_BANK(gpio);
+ int bitmask = GPIO_BITMASK(gpio);
+ u32 val, off;
+
+ /* determine the GPIO pin direction */
+ val = readl(GPIO_BASE + GPIO_CONTROL(gpio));
+ val &= GPIO_GPCTR0_IOTR_MASK;
+
+ /* read the GPIO bank status */
+ off = (GPIO_GPCTR0_IOTR_CMD_INPUT == val) ?
+ GPIO_IN_STATUS(bank_id) : GPIO_OUT_STATUS(bank_id);
+ val = readl(GPIO_BASE + off);
+
+ /* return the specified bit status */
+ return !!(val & bitmask);
+}
+
+void gpio_set_value(unsigned gpio, int value)
+{
+ int bank_id = GPIO_BANK(gpio);
+ int bitmask = GPIO_BITMASK(gpio);
+ u32 val, off;
+
+ /* determine the GPIO pin direction */
+ val = readl(GPIO_BASE + GPIO_CONTROL(gpio));
+ val &= GPIO_GPCTR0_IOTR_MASK;
+
+ /* this function only applies to output pin */
+ if (GPIO_GPCTR0_IOTR_CMD_INPUT == val) {
+ printf("%s: Cannot set an input pin %d\n", __func__, gpio);
+ return;
+ }
+
+ off = value ? GPIO_OUT_SET(bank_id) : GPIO_OUT_CLEAR(bank_id);
+
+ val = readl(GPIO_BASE + off);
+ val |= bitmask;
+ writel(val, GPIO_BASE + off);
+}
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index fa3a875..36d5e5f 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -18,6 +18,7 @@
obj-$(CONFIG_SYS_I2C) += i2c_core.o
obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o
obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o
+obj-$(CONFIG_SYS_I2C_KONA) += kona_i2c.o
obj-$(CONFIG_SYS_I2C_MXC) += mxc_i2c.o
obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o
obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o
diff --git a/drivers/i2c/kona_i2c.c b/drivers/i2c/kona_i2c.c
new file mode 100644
index 0000000..0b1715a
--- /dev/null
+++ b/drivers/i2c/kona_i2c.c
@@ -0,0 +1,730 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/sysmap.h>
+#include <asm/kona-common/clk.h>
+#include <i2c.h>
+
+/* Hardware register offsets and field defintions */
+#define CS_OFFSET 0x00000020
+#define CS_ACK_SHIFT 3
+#define CS_ACK_MASK 0x00000008
+#define CS_ACK_CMD_GEN_START 0x00000000
+#define CS_ACK_CMD_GEN_RESTART 0x00000001
+#define CS_CMD_SHIFT 1
+#define CS_CMD_CMD_NO_ACTION 0x00000000
+#define CS_CMD_CMD_START_RESTART 0x00000001
+#define CS_CMD_CMD_STOP 0x00000002
+#define CS_EN_SHIFT 0
+#define CS_EN_CMD_ENABLE_BSC 0x00000001
+
+#define TIM_OFFSET 0x00000024
+#define TIM_PRESCALE_SHIFT 6
+#define TIM_P_SHIFT 3
+#define TIM_NO_DIV_SHIFT 2
+#define TIM_DIV_SHIFT 0
+
+#define DAT_OFFSET 0x00000028
+
+#define TOUT_OFFSET 0x0000002c
+
+#define TXFCR_OFFSET 0x0000003c
+#define TXFCR_FIFO_FLUSH_MASK 0x00000080
+#define TXFCR_FIFO_EN_MASK 0x00000040
+
+#define IER_OFFSET 0x00000044
+#define IER_READ_COMPLETE_INT_MASK 0x00000010
+#define IER_I2C_INT_EN_MASK 0x00000008
+#define IER_FIFO_INT_EN_MASK 0x00000002
+#define IER_NOACK_EN_MASK 0x00000001
+
+#define ISR_OFFSET 0x00000048
+#define ISR_RESERVED_MASK 0xffffff60
+#define ISR_CMDBUSY_MASK 0x00000080
+#define ISR_READ_COMPLETE_MASK 0x00000010
+#define ISR_SES_DONE_MASK 0x00000008
+#define ISR_ERR_MASK 0x00000004
+#define ISR_TXFIFOEMPTY_MASK 0x00000002
+#define ISR_NOACK_MASK 0x00000001
+
+#define CLKEN_OFFSET 0x0000004c
+#define CLKEN_AUTOSENSE_OFF_MASK 0x00000080
+#define CLKEN_M_SHIFT 4
+#define CLKEN_N_SHIFT 1
+#define CLKEN_CLKEN_MASK 0x00000001
+
+#define FIFO_STATUS_OFFSET 0x00000054
+#define FIFO_STATUS_RXFIFO_EMPTY_MASK 0x00000004
+#define FIFO_STATUS_TXFIFO_EMPTY_MASK 0x00000010
+
+#define HSTIM_OFFSET 0x00000058
+#define HSTIM_HS_MODE_MASK 0x00008000
+#define HSTIM_HS_HOLD_SHIFT 10
+#define HSTIM_HS_HIGH_PHASE_SHIFT 5
+#define HSTIM_HS_SETUP_SHIFT 0
+
+#define PADCTL_OFFSET 0x0000005c
+#define PADCTL_PAD_OUT_EN_MASK 0x00000004
+
+#define RXFCR_OFFSET 0x00000068
+#define RXFCR_NACK_EN_SHIFT 7
+#define RXFCR_READ_COUNT_SHIFT 0
+#define RXFIFORDOUT_OFFSET 0x0000006c
+
+/* Locally used constants */
+#define MAX_RX_FIFO_SIZE 64U /* bytes */
+#define MAX_TX_FIFO_SIZE 64U /* bytes */
+
+#define I2C_TIMEOUT 100000 /* usecs */
+
+#define WAIT_INT_CHK 100 /* usecs */
+#if I2C_TIMEOUT % WAIT_INT_CHK
+#error I2C_TIMEOUT must be a multiple of WAIT_INT_CHK
+#endif
+
+/* Operations that can be commanded to the controller */
+enum bcm_kona_cmd_t {
+ BCM_CMD_NOACTION = 0,
+ BCM_CMD_START,
+ BCM_CMD_RESTART,
+ BCM_CMD_STOP,
+};
+
+enum bus_speed_index {
+ BCM_SPD_100K = 0,
+ BCM_SPD_400K,
+ BCM_SPD_1MHZ,
+};
+
+/* Internal divider settings for standard mode, fast mode and fast mode plus */
+struct bus_speed_cfg {
+ uint8_t time_m; /* Number of cycles for setup time */
+ uint8_t time_n; /* Number of cycles for hold time */
+ uint8_t prescale; /* Prescale divider */
+ uint8_t time_p; /* Timing coefficient */
+ uint8_t no_div; /* Disable clock divider */
+ uint8_t time_div; /* Post-prescale divider */
+};
+
+static const struct bus_speed_cfg std_cfg_table[] = {
+ [BCM_SPD_100K] = {0x01, 0x01, 0x03, 0x06, 0x00, 0x02},
+ [BCM_SPD_400K] = {0x05, 0x01, 0x03, 0x05, 0x01, 0x02},
+ [BCM_SPD_1MHZ] = {0x01, 0x01, 0x03, 0x01, 0x01, 0x03},
+};
+
+struct bcm_kona_i2c_dev {
+ void *base;
+ uint speed;
+ const struct bus_speed_cfg *std_cfg;
+};
+
+/* Keep these two defines in sync */
+#define DEF_SPD 100000
+#define DEF_SPD_ENUM BCM_SPD_100K
+
+#define DEF_DEVICE(num) \
+{(void *)CONFIG_SYS_I2C_BASE##num, DEF_SPD, &std_cfg_table[DEF_SPD_ENUM]}
+
+static struct bcm_kona_i2c_dev g_i2c_devs[CONFIG_SYS_MAX_I2C_BUS] = {
+#ifdef CONFIG_SYS_I2C_BASE0
+ DEF_DEVICE(0),
+#endif
+#ifdef CONFIG_SYS_I2C_BASE1
+ DEF_DEVICE(1),
+#endif
+#ifdef CONFIG_SYS_I2C_BASE2
+ DEF_DEVICE(2),
+#endif
+#ifdef CONFIG_SYS_I2C_BASE3
+ DEF_DEVICE(3),
+#endif
+#ifdef CONFIG_SYS_I2C_BASE4
+ DEF_DEVICE(4),
+#endif
+#ifdef CONFIG_SYS_I2C_BASE5
+ DEF_DEVICE(5),
+#endif
+};
+
+#define I2C_M_TEN 0x0010 /* ten bit address */
+#define I2C_M_RD 0x0001 /* read data */
+#define I2C_M_NOSTART 0x4000 /* no restart between msgs */
+
+struct i2c_msg {
+ uint16_t addr;
+ uint16_t flags;
+ uint16_t len;
+ uint8_t *buf;
+};
+
+static void bcm_kona_i2c_send_cmd_to_ctrl(struct bcm_kona_i2c_dev *dev,
+ enum bcm_kona_cmd_t cmd)
+{
+ debug("%s, %d\n", __func__, cmd);
+
+ switch (cmd) {
+ case BCM_CMD_NOACTION:
+ writel((CS_CMD_CMD_NO_ACTION << CS_CMD_SHIFT) |
+ (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
+ dev->base + CS_OFFSET);
+ break;
+
+ case BCM_CMD_START:
+ writel((CS_ACK_CMD_GEN_START << CS_ACK_SHIFT) |
+ (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) |
+ (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
+ dev->base + CS_OFFSET);
+ break;
+
+ case BCM_CMD_RESTART:
+ writel((CS_ACK_CMD_GEN_RESTART << CS_ACK_SHIFT) |
+ (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) |
+ (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
+ dev->base + CS_OFFSET);
+ break;
+
+ case BCM_CMD_STOP:
+ writel((CS_CMD_CMD_STOP << CS_CMD_SHIFT) |
+ (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT),
+ dev->base + CS_OFFSET);
+ break;
+
+ default:
+ printf("Unknown command %d\n", cmd);
+ }
+}
+
+static void bcm_kona_i2c_enable_clock(struct bcm_kona_i2c_dev *dev)
+{
+ writel(readl(dev->base + CLKEN_OFFSET) | CLKEN_CLKEN_MASK,
+ dev->base + CLKEN_OFFSET);
+}
+
+static void bcm_kona_i2c_disable_clock(struct bcm_kona_i2c_dev *dev)
+{
+ writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_CLKEN_MASK,
+ dev->base + CLKEN_OFFSET);
+}
+
+/* Wait until at least one of the mask bit(s) are set */
+static unsigned long wait_for_int_timeout(struct bcm_kona_i2c_dev *dev,
+ unsigned long time_left,
+ uint32_t mask)
+{
+ uint32_t status;
+
+ while (time_left) {
+ status = readl(dev->base + ISR_OFFSET);
+
+ if ((status & ~ISR_RESERVED_MASK) == 0) {
+ debug("Bogus I2C interrupt 0x%x\n", status);
+ continue;
+ }
+
+ /* Must flush the TX FIFO when NAK detected */
+ if (status & ISR_NOACK_MASK)
+ writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK,
+ dev->base + TXFCR_OFFSET);
+
+ writel(status & ~ISR_RESERVED_MASK, dev->base + ISR_OFFSET);
+
+ if (status & mask) {
+ /* We are done since one of the mask bits are set */
+ return time_left;
+ }
+ udelay(WAIT_INT_CHK);
+ time_left -= WAIT_INT_CHK;
+ }
+ return 0;
+}
+
+/* Send command to I2C bus */
+static int bcm_kona_send_i2c_cmd(struct bcm_kona_i2c_dev *dev,
+ enum bcm_kona_cmd_t cmd)
+{
+ int rc = 0;
+ unsigned long time_left = I2C_TIMEOUT;
+
+ /* Send the command */
+ bcm_kona_i2c_send_cmd_to_ctrl(dev, cmd);
+
+ /* Wait for transaction to finish or timeout */
+ time_left = wait_for_int_timeout(dev, time_left, IER_I2C_INT_EN_MASK);
+
+ if (!time_left) {
+ printf("controller timed out\n");
+ rc = -ETIMEDOUT;
+ }
+
+ /* Clear command */
+ bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION);
+
+ return rc;
+}
+
+/* Read a single RX FIFO worth of data from the i2c bus */
+static int bcm_kona_i2c_read_fifo_single(struct bcm_kona_i2c_dev *dev,
+ uint8_t *buf, unsigned int len,
+ unsigned int last_byte_nak)
+{
+ unsigned long time_left = I2C_TIMEOUT;
+
+ /* Start the RX FIFO */
+ writel((last_byte_nak << RXFCR_NACK_EN_SHIFT) |
+ (len << RXFCR_READ_COUNT_SHIFT), dev->base + RXFCR_OFFSET);
+
+ /* Wait for FIFO read to complete */
+ time_left =
+ wait_for_int_timeout(dev, time_left, IER_READ_COMPLETE_INT_MASK);
+
+ if (!time_left) {
+ printf("RX FIFO time out\n");
+ return -EREMOTEIO;
+ }
+
+ /* Read data from FIFO */
+ for (; len > 0; len--, buf++)
+ *buf = readl(dev->base + RXFIFORDOUT_OFFSET);
+
+ return 0;
+}
+
+/* Read any amount of data using the RX FIFO from the i2c bus */
+static int bcm_kona_i2c_read_fifo(struct bcm_kona_i2c_dev *dev,
+ struct i2c_msg *msg)
+{
+ unsigned int bytes_to_read = MAX_RX_FIFO_SIZE;
+ unsigned int last_byte_nak = 0;
+ unsigned int bytes_read = 0;
+ int rc;
+
+ uint8_t *tmp_buf = msg->buf;
+
+ while (bytes_read < msg->len) {
+ if (msg->len - bytes_read <= MAX_RX_FIFO_SIZE) {
+ last_byte_nak = 1; /* NAK last byte of transfer */
+ bytes_to_read = msg->len - bytes_read;
+ }
+
+ rc = bcm_kona_i2c_read_fifo_single(dev, tmp_buf, bytes_to_read,
+ last_byte_nak);
+ if (rc < 0)
+ return -EREMOTEIO;
+
+ bytes_read += bytes_to_read;
+ tmp_buf += bytes_to_read;
+ }
+
+ return 0;
+}
+
+/* Write a single byte of data to the i2c bus */
+static int bcm_kona_i2c_write_byte(struct bcm_kona_i2c_dev *dev, uint8_t data,
+ unsigned int nak_expected)
+{
+ unsigned long time_left = I2C_TIMEOUT;
+ unsigned int nak_received;
+
+ /* Clear pending session done interrupt */
+ writel(ISR_SES_DONE_MASK, dev->base + ISR_OFFSET);
+
+ /* Send one byte of data */
+ writel(data, dev->base + DAT_OFFSET);
+
+ time_left = wait_for_int_timeout(dev, time_left, IER_I2C_INT_EN_MASK);
+
+ if (!time_left) {
+ debug("controller timed out\n");
+ return -ETIMEDOUT;
+ }
+
+ nak_received = readl(dev->base + CS_OFFSET) & CS_ACK_MASK ? 1 : 0;
+
+ if (nak_received ^ nak_expected) {
+ debug("unexpected NAK/ACK\n");
+ return -EREMOTEIO;
+ }
+
+ return 0;
+}
+
+/* Write a single TX FIFO worth of data to the i2c bus */
+static int bcm_kona_i2c_write_fifo_single(struct bcm_kona_i2c_dev *dev,
+ uint8_t *buf, unsigned int len)
+{
+ int k;
+ unsigned long time_left = I2C_TIMEOUT;
+ unsigned int fifo_status;
+
+ /* Write data into FIFO */
+ for (k = 0; k < len; k++)
+ writel(buf[k], (dev->base + DAT_OFFSET));
+
+ /* Wait for FIFO to empty */
+ do {
+ time_left =
+ wait_for_int_timeout(dev, time_left,
+ (IER_FIFO_INT_EN_MASK |
+ IER_NOACK_EN_MASK));
+ fifo_status = readl(dev->base + FIFO_STATUS_OFFSET);
+ } while (time_left && !(fifo_status & FIFO_STATUS_TXFIFO_EMPTY_MASK));
+
+ /* Check if there was a NAK */
+ if (readl(dev->base + CS_OFFSET) & CS_ACK_MASK) {
+ printf("unexpected NAK\n");
+ return -EREMOTEIO;
+ }
+
+ /* Check if a timeout occured */
+ if (!time_left) {
+ printf("completion timed out\n");
+ return -EREMOTEIO;
+ }
+
+ return 0;
+}
+
+/* Write any amount of data using TX FIFO to the i2c bus */
+static int bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev *dev,
+ struct i2c_msg *msg)
+{
+ unsigned int bytes_to_write = MAX_TX_FIFO_SIZE;
+ unsigned int bytes_written = 0;
+ int rc;
+
+ uint8_t *tmp_buf = msg->buf;
+
+ while (bytes_written < msg->len) {
+ if (msg->len - bytes_written <= MAX_TX_FIFO_SIZE)
+ bytes_to_write = msg->len - bytes_written;
+
+ rc = bcm_kona_i2c_write_fifo_single(dev, tmp_buf,
+ bytes_to_write);
+ if (rc < 0)
+ return -EREMOTEIO;
+
+ bytes_written += bytes_to_write;
+ tmp_buf += bytes_to_write;
+ }
+
+ return 0;
+}
+
+/* Send i2c address */
+static int bcm_kona_i2c_do_addr(struct bcm_kona_i2c_dev *dev,
+ struct i2c_msg *msg)
+{
+ unsigned char addr;
+
+ if (msg->flags & I2C_M_TEN) {
+ /* First byte is 11110XX0 where XX is upper 2 bits */
+ addr = 0xf0 | ((msg->addr & 0x300) >> 7);
+ if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
+ return -EREMOTEIO;
+
+ /* Second byte is the remaining 8 bits */
+ addr = msg->addr & 0xff;
+ if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
+ return -EREMOTEIO;
+
+ if (msg->flags & I2C_M_RD) {
+ /* For read, send restart command */
+ if (bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART) < 0)
+ return -EREMOTEIO;
+
+ /* Then re-send the first byte with the read bit set */
+ addr = 0xf0 | ((msg->addr & 0x300) >> 7) | 0x01;
+ if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
+ return -EREMOTEIO;
+ }
+ } else {
+ addr = msg->addr << 1;
+
+ if (msg->flags & I2C_M_RD)
+ addr |= 1;
+
+ if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0)
+ return -EREMOTEIO;
+ }
+
+ return 0;
+}
+
+static void bcm_kona_i2c_enable_autosense(struct bcm_kona_i2c_dev *dev)
+{
+ writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_AUTOSENSE_OFF_MASK,
+ dev->base + CLKEN_OFFSET);
+}
+
+static void bcm_kona_i2c_config_timing(struct bcm_kona_i2c_dev *dev)
+{
+ writel(readl(dev->base + HSTIM_OFFSET) & ~HSTIM_HS_MODE_MASK,
+ dev->base + HSTIM_OFFSET);
+
+ writel((dev->std_cfg->prescale << TIM_PRESCALE_SHIFT) |
+ (dev->std_cfg->time_p << TIM_P_SHIFT) |
+ (dev->std_cfg->no_div << TIM_NO_DIV_SHIFT) |
+ (dev->std_cfg->time_div << TIM_DIV_SHIFT),
+ dev->base + TIM_OFFSET);
+
+ writel((dev->std_cfg->time_m << CLKEN_M_SHIFT) |
+ (dev->std_cfg->time_n << CLKEN_N_SHIFT) |
+ CLKEN_CLKEN_MASK, dev->base + CLKEN_OFFSET);
+}
+
+/* Master transfer function */
+static int bcm_kona_i2c_xfer(struct bcm_kona_i2c_dev *dev,
+ struct i2c_msg msgs[], int num)
+{
+ struct i2c_msg *pmsg;
+ int rc = 0;
+ int i;
+
+ /* Enable pad output */
+ writel(0, dev->base + PADCTL_OFFSET);
+
+ /* Enable internal clocks */
+ bcm_kona_i2c_enable_clock(dev);
+
+ /* Send start command */
+ rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_START);
+ if (rc < 0) {
+ printf("Start command failed rc = %d\n", rc);
+ goto xfer_disable_pad;
+ }
+
+ /* Loop through all messages */
+ for (i = 0; i < num; i++) {
+ pmsg = &msgs[i];
+
+ /* Send restart for subsequent messages */
+ if ((i != 0) && ((pmsg->flags & I2C_M_NOSTART) == 0)) {
+ rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART);
+ if (rc < 0) {
+ printf("restart cmd failed rc = %d\n", rc);
+ goto xfer_send_stop;
+ }
+ }
+
+ /* Send slave address */
+ if (!(pmsg->flags & I2C_M_NOSTART)) {
+ rc = bcm_kona_i2c_do_addr(dev, pmsg);
+ if (rc < 0) {
+ debug("NAK from addr %2.2x msg#%d rc = %d\n",
+ pmsg->addr, i, rc);
+ goto xfer_send_stop;
+ }
+ }
+
+ /* Perform data transfer */
+ if (pmsg->flags & I2C_M_RD) {
+ rc = bcm_kona_i2c_read_fifo(dev, pmsg);
+ if (rc < 0) {
+ printf("read failure\n");
+ goto xfer_send_stop;
+ }
+ } else {
+ rc = bcm_kona_i2c_write_fifo(dev, pmsg);
+ if (rc < 0) {
+ printf("write failure");
+ goto xfer_send_stop;
+ }
+ }
+ }
+
+ rc = num;
+
+xfer_send_stop:
+ /* Send a STOP command */
+ bcm_kona_send_i2c_cmd(dev, BCM_CMD_STOP);
+
+xfer_disable_pad:
+ /* Disable pad output */
+ writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET);
+
+ /* Stop internal clock */
+ bcm_kona_i2c_disable_clock(dev);
+
+ return rc;
+}
+
+static uint bcm_kona_i2c_assign_bus_speed(struct bcm_kona_i2c_dev *dev,
+ uint speed)
+{
+ switch (speed) {
+ case 100000:
+ dev->std_cfg = &std_cfg_table[BCM_SPD_100K];
+ break;
+ case 400000:
+ dev->std_cfg = &std_cfg_table[BCM_SPD_400K];
+ break;
+ case 1000000:
+ dev->std_cfg = &std_cfg_table[BCM_SPD_1MHZ];
+ break;
+ default:
+ printf("%d hz bus speed not supported\n", speed);
+ return -EINVAL;
+ }
+ dev->speed = speed;
+ return 0;
+}
+
+static void bcm_kona_i2c_init(struct bcm_kona_i2c_dev *dev)
+{
+ /* Parse bus speed */
+ bcm_kona_i2c_assign_bus_speed(dev, dev->speed);
+
+ /* Enable internal clocks */
+ bcm_kona_i2c_enable_clock(dev);
+
+ /* Configure internal dividers */
+ bcm_kona_i2c_config_timing(dev);
+
+ /* Disable timeout */
+ writel(0, dev->base + TOUT_OFFSET);
+
+ /* Enable autosense */
+ bcm_kona_i2c_enable_autosense(dev);
+
+ /* Enable TX FIFO */
+ writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK,
+ dev->base + TXFCR_OFFSET);
+
+ /* Mask all interrupts */
+ writel(0, dev->base + IER_OFFSET);
+
+ /* Clear all pending interrupts */
+ writel(ISR_CMDBUSY_MASK |
+ ISR_READ_COMPLETE_MASK |
+ ISR_SES_DONE_MASK |
+ ISR_ERR_MASK |
+ ISR_TXFIFOEMPTY_MASK | ISR_NOACK_MASK, dev->base + ISR_OFFSET);
+
+ /* Enable the controller but leave it idle */
+ bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION);
+
+ /* Disable pad output */
+ writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET);
+}
+
+/*
+ * uboot layer
+ */
+struct bcm_kona_i2c_dev *kona_get_dev(struct i2c_adapter *adap)
+{
+ return &g_i2c_devs[adap->hwadapnr];
+}
+
+static void kona_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
+{
+ struct bcm_kona_i2c_dev *dev = kona_get_dev(adap);
+
+ if (clk_bsc_enable(dev->base))
+ return;
+
+ bcm_kona_i2c_init(dev);
+}
+
+static int kona_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *buffer, int len)
+{
+ /* msg[0] writes the addr, msg[1] reads the data */
+ struct i2c_msg msg[2];
+ unsigned char msgbuf0[64];
+ struct bcm_kona_i2c_dev *dev = kona_get_dev(adap);
+
+ msg[0].addr = chip;
+ msg[0].flags = 0;
+ msg[0].len = 1;
+ msg[0].buf = msgbuf0; /* msgbuf0 contains incrementing reg addr */
+
+ msg[1].addr = chip;
+ msg[1].flags = I2C_M_RD;
+ /* msg[1].buf dest ptr increments each read */
+
+ msgbuf0[0] = (unsigned char)addr;
+ msg[1].buf = buffer;
+ msg[1].len = len;
+ if (bcm_kona_i2c_xfer(dev, msg, 2) < 0) {
+ /* Sending 2 i2c messages */
+ kona_i2c_init(adap, adap->speed, adap->slaveaddr);
+ debug("I2C read: I/O error\n");
+ return -EIO;
+ }
+ return 0;
+}
+
+static int kona_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+ int alen, uchar *buffer, int len)
+{
+ struct i2c_msg msg[0];
+ unsigned char msgbuf0[64];
+ unsigned int i;
+ struct bcm_kona_i2c_dev *dev = kona_get_dev(adap);
+
+ msg[0].addr = chip;
+ msg[0].flags = 0;
+ msg[0].len = 2; /* addr byte plus data */
+ msg[0].buf = msgbuf0;
+
+ for (i = 0; i < len; i++) {
+ msgbuf0[0] = addr++;
+ msgbuf0[1] = buffer[i];
+ if (bcm_kona_i2c_xfer(dev, msg, 1) < 0) {
+ kona_i2c_init(adap, adap->speed, adap->slaveaddr);
+ debug("I2C write: I/O error\n");
+ return -EIO;
+ }
+ }
+ return 0;
+}
+
+static int kona_i2c_probe(struct i2c_adapter *adap, uchar chip)
+{
+ uchar tmp;
+
+ /*
+ * read addr 0x0 of the given chip.
+ */
+ return kona_i2c_read(adap, chip, 0x0, 1, &tmp, 1);
+}
+
+static uint kona_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed)
+{
+ struct bcm_kona_i2c_dev *dev = kona_get_dev(adap);
+ return bcm_kona_i2c_assign_bus_speed(dev, speed);
+}
+
+/*
+ * Register kona i2c adapters. Keep the order below so
+ * that the bus number matches the adapter number.
+ */
+#define DEF_ADAPTER(num) \
+U_BOOT_I2C_ADAP_COMPLETE(kona##num, kona_i2c_init, kona_i2c_probe, \
+ kona_i2c_read, kona_i2c_write, \
+ kona_i2c_set_bus_speed, DEF_SPD, 0x00, num)
+
+#ifdef CONFIG_SYS_I2C_BASE0
+ DEF_ADAPTER(0)
+#endif
+#ifdef CONFIG_SYS_I2C_BASE1
+ DEF_ADAPTER(1)
+#endif
+#ifdef CONFIG_SYS_I2C_BASE2
+ DEF_ADAPTER(2)
+#endif
+#ifdef CONFIG_SYS_I2C_BASE3
+ DEF_ADAPTER(3)
+#endif
+#ifdef CONFIG_SYS_I2C_BASE4
+ DEF_ADAPTER(4)
+#endif
+#ifdef CONFIG_SYS_I2C_BASE5
+ DEF_ADAPTER(5)
+#endif
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index e793ed9..931922b 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -21,6 +21,7 @@
obj-$(CONFIG_PXA_MMC_GENERIC) += pxa_mmc_gen.o
obj-$(CONFIG_SDHCI) += sdhci.o
obj-$(CONFIG_BCM2835_SDHCI) += bcm2835_sdhci.o
+obj-$(CONFIG_KONA_SDHCI) += kona_sdhci.o
obj-$(CONFIG_S5P_SDHCI) += s5p_sdhci.o
obj-$(CONFIG_SH_MMCIF) += sh_mmcif.o
obj-$(CONFIG_SPEAR_SDHCI) += spear_sdhci.o
diff --git a/drivers/mmc/kona_sdhci.c b/drivers/mmc/kona_sdhci.c
new file mode 100644
index 0000000..77e42c8
--- /dev/null
+++ b/drivers/mmc/kona_sdhci.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <sdhci.h>
+#include <asm/errno.h>
+#include <asm/kona-common/clk.h>
+
+#define SDHCI_CORECTRL_OFFSET 0x00008000
+#define SDHCI_CORECTRL_EN 0x01
+#define SDHCI_CORECTRL_RESET 0x02
+
+#define SDHCI_CORESTAT_OFFSET 0x00008004
+#define SDHCI_CORESTAT_CD_SW 0x01
+
+#define SDHCI_COREIMR_OFFSET 0x00008008
+#define SDHCI_COREIMR_IP 0x01
+
+static int init_kona_mmc_core(struct sdhci_host *host)
+{
+ unsigned int mask;
+ unsigned int timeout;
+
+ if (sdhci_readb(host, SDHCI_SOFTWARE_RESET) & SDHCI_RESET_ALL) {
+ printf("%s: sd host controller reset error\n", __func__);
+ return 1;
+ }
+
+ /* For kona a hardware reset before anything else. */
+ mask = sdhci_readl(host, SDHCI_CORECTRL_OFFSET) | SDHCI_CORECTRL_RESET;
+ sdhci_writel(host, mask, SDHCI_CORECTRL_OFFSET);
+
+ /* Wait max 100 ms */
+ timeout = 1000;
+ do {
+ if (timeout == 0) {
+ printf("%s: reset timeout error\n", __func__);
+ return 1;
+ }
+ timeout--;
+ udelay(100);
+ } while (0 ==
+ (sdhci_readl(host, SDHCI_CORECTRL_OFFSET) &
+ SDHCI_CORECTRL_RESET));
+
+ /* Clear the reset bit. */
+ mask = mask & ~SDHCI_CORECTRL_RESET;
+ sdhci_writel(host, mask, SDHCI_CORECTRL_OFFSET);
+
+ /* Enable AHB clock */
+ mask = sdhci_readl(host, SDHCI_CORECTRL_OFFSET);
+ sdhci_writel(host, mask | SDHCI_CORECTRL_EN, SDHCI_CORECTRL_OFFSET);
+
+ /* Enable interrupts */
+ sdhci_writel(host, SDHCI_COREIMR_IP, SDHCI_COREIMR_OFFSET);
+
+ /* Make sure Card is detected in controller */
+ mask = sdhci_readl(host, SDHCI_CORESTAT_OFFSET);
+ sdhci_writel(host, mask | SDHCI_CORESTAT_CD_SW, SDHCI_CORESTAT_OFFSET);
+
+ /* Wait max 100 ms */
+ timeout = 1000;
+ while (!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) {
+ if (timeout == 0) {
+ printf("%s: CARD DETECT timeout error\n", __func__);
+ return 1;
+ }
+ timeout--;
+ udelay(100);
+ }
+ return 0;
+}
+
+int kona_sdhci_init(int dev_index, u32 min_clk, u32 quirks)
+{
+ int ret = 0;
+ u32 max_clk;
+ void *reg_base;
+ struct sdhci_host *host = NULL;
+
+ host = (struct sdhci_host *)malloc(sizeof(struct sdhci_host));
+ if (!host) {
+ printf("%s: sdhci host malloc fail!\n", __func__);
+ return -ENOMEM;
+ }
+ switch (dev_index) {
+ case 0:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE0;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO0_MAX_CLK,
+ &max_clk);
+ break;
+ case 1:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE1;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO1_MAX_CLK,
+ &max_clk);
+ break;
+ case 2:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE2;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO2_MAX_CLK,
+ &max_clk);
+ break;
+ case 3:
+ reg_base = (void *)CONFIG_SYS_SDIO_BASE3;
+ ret = clk_sdio_enable(reg_base, CONFIG_SYS_SDIO3_MAX_CLK,
+ &max_clk);
+ break;
+ default:
+ printf("%s: sdio dev index %d not supported\n",
+ __func__, dev_index);
+ ret = -EINVAL;
+ }
+ if (ret)
+ return ret;
+
+ host->name = "kona-sdhci";
+ host->ioaddr = reg_base;
+ host->quirks = quirks;
+ host->host_caps = MMC_MODE_HC;
+
+ if (init_kona_mmc_core(host))
+ return -EINVAL;
+
+ if (quirks & SDHCI_QUIRK_REG32_RW)
+ host->version = sdhci_readl(host, SDHCI_HOST_VERSION - 2) >> 16;
+ else
+ host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
+
+ add_sdhci(host, max_clk, min_clk);
+ return ret;
+}
diff --git a/fs/ubifs/Makefile b/fs/ubifs/Makefile
index 6b1a9a5..8c8c6ac 100644
--- a/fs/ubifs/Makefile
+++ b/fs/ubifs/Makefile
@@ -13,6 +13,3 @@
obj-y += lpt_commit.o scan.o lprops.o
obj-y += tnc.o tnc_misc.o debug.o crc16.o budget.o
obj-y += log.o orphan.o recovery.o replay.o
-
-# SEE README.arm-unaligned-accesses
-CFLAGS_super.o := $(PLATFORM_NO_UNALIGNED)
diff --git a/include/asm-generic/sections.h b/include/asm-generic/sections.h
index 7e1eb4b..458952f 100644
--- a/include/asm-generic/sections.h
+++ b/include/asm-generic/sections.h
@@ -63,28 +63,16 @@
extern void _start(void);
/*
- * ARM needs to use offsets for symbols, since the values of some symbols
- * are not resolved prior to relocation (and are just 0). Maybe this can be
- * resolved, or maybe other architectures are similar, iwc this should be
- * promoted to an architecture option.
+ * ARM defines its symbols as char[]. Other arches define them as ulongs.
*/
#ifdef CONFIG_ARM
-#define CONFIG_SYS_SYM_OFFSETS
-#endif
-#ifdef CONFIG_SYS_SYM_OFFSETS
-/* Start/end of the relocation entries, as an offset from _start */
-extern ulong _rel_dyn_start_ofs;
-extern ulong _rel_dyn_end_ofs;
-
-/* End of the region to be relocated, as an offset form _start */
-extern ulong _image_copy_end_ofs;
-
-extern ulong _bss_start_ofs; /* BSS start relative to _start */
-extern ulong _bss_end_ofs; /* BSS end relative to _start */
-extern ulong _end_ofs; /* end of image relative to _start */
-
-extern ulong _TEXT_BASE; /* code start */
+extern char __bss_start[];
+extern char __bss_end[];
+extern char __image_copy_start[];
+extern char __image_copy_end[];
+extern char __rel_dyn_start[];
+extern char __rel_dyn_end[];
#else /* don't use offsets: */
diff --git a/include/bitfield.h b/include/bitfield.h
new file mode 100644
index 0000000..ec4815c
--- /dev/null
+++ b/include/bitfield.h
@@ -0,0 +1,58 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * Bitfield operations
+ *
+ * These are generic bitfield operations which allow manipulation of variable
+ * width bitfields within a word. One use of this would be to use data tables
+ * to determine how to reprogram fields within R/W hardware registers.
+ *
+ * Example:
+ *
+ * old_reg_val
+ * +--------+----+---+--+-----+----------+
+ * | | | | | old | |
+ * +--------+----+---+--+-----+----------+
+ *
+ * new_reg_val
+ * +--------+----+---+--+-----+----------+
+ * | | | | | new | |
+ * +--------+----+---+--+-----+----------+
+ *
+ * mask = bitfield_mask(10, 5);
+ * old = bitfield_extract(old_reg_val, 10, 5);
+ * new_reg_val = bitfield_replace(old_reg_val, 10, 5, new);
+ *
+ * The numbers 10 and 5 could for example come from data
+ * tables which describe all bitfields in all registers.
+ */
+
+#include <linux/types.h>
+
+/* Produces a mask of set bits covering a range of a uint value */
+static inline uint bitfield_mask(uint shift, uint width)
+{
+ return ((1 << width) - 1) << shift;
+}
+
+/* Extract the value of a bitfield found within a given register value */
+static inline uint bitfield_extract(uint reg_val, uint shift, uint width)
+{
+ return (reg_val & bitfield_mask(shift, width)) >> shift;
+}
+
+/*
+ * Replace the value of a bitfield found within a given register value
+ * Returns the newly modified uint value with the replaced field.
+ */
+static inline uint bitfield_replace(uint reg_val, uint shift, uint width,
+ uint bitfield_val)
+{
+ uint mask = bitfield_mask(shift, width);
+
+ return (reg_val & ~mask) | (bitfield_val << shift);
+}
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 73a9adb..59a8f36 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -20,6 +20,7 @@
#define MACH_TYPE_TIAM335EVM 3589 /* Until the next sync */
#define CONFIG_MACH_TYPE MACH_TYPE_TIAM335EVM
+#define CONFIG_BOARD_LATE_INIT
/* Clock Defines */
#define V_OSCK 24000000 /* Clock output from T2 */
@@ -31,6 +32,12 @@
/* Always 128 KiB env size */
#define CONFIG_ENV_SIZE (128 << 10)
+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
#ifdef CONFIG_NAND
#define NANDARGS \
"mtdids=" MTDIDS_DEFAULT "\0" \
@@ -64,6 +71,9 @@
"bootfile=zImage\0" \
"fdtfile=undefined\0" \
"console=ttyO0,115200n8\0" \
+ "partitions=" \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \
"optargs=\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 ro\0" \
@@ -295,6 +305,9 @@
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT)
/* disable host part of MUSB in SPL */
#undef CONFIG_MUSB_HOST
+/* disable EFI partitions and partition UUID support */
+#undef CONFIG_PARTITION_UUIDS
+#undef CONFIG_EFI_PARTITION
/*
* Disable CPSW SPL support so we fit within the 101KiB limit.
*/
diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h
index 9a44990..c773a18 100644
--- a/include/configs/am43xx_evm.h
+++ b/include/configs/am43xx_evm.h
@@ -104,6 +104,12 @@
#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
#ifndef CONFIG_SPL_BUILD
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x80200000\0" \
@@ -115,6 +121,9 @@
"bootdir=/boot\0" \
"bootfile=zImage\0" \
"console=ttyO0,115200n8\0" \
+ "partitions=" \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \
"optargs=\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
diff --git a/include/configs/bcm28155_ap.h b/include/configs/bcm28155_ap.h
new file mode 100644
index 0000000..8e1c81f
--- /dev/null
+++ b/include/configs/bcm28155_ap.h
@@ -0,0 +1,140 @@
+/*
+ * Copyright 2013 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __BCM28155_AP_H
+#define __BCM28155_AP_H
+
+#include <asm/sizes.h>
+#include <asm/arch/sysmap.h>
+
+/* Architecture, CPU, chip, mach, etc */
+#define CONFIG_ARMV7
+#define CONFIG_KONA
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Memory configuration
+ */
+#define CONFIG_SYS_TEXT_BASE 0xae000000
+
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_SDRAM_SIZE 0x80000000
+#define CONFIG_NR_DRAM_BANKS 1
+
+#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */
+#define CONFIG_STACKSIZE SZ_256K
+
+/* GPIO Driver */
+#define CONFIG_KONA_GPIO
+
+/* MMC/SD Driver */
+#define CONFIG_SDHCI
+#define CONFIG_MMC_SDMA
+#define CONFIG_KONA_SDHCI
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+
+#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
+#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
+#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
+#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
+#define CONFIG_SYS_SDIO0_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO1_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO2_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO3_MAX_CLK 48000000
+#define CONFIG_SYS_SDIO0 "sdio1"
+#define CONFIG_SYS_SDIO1 "sdio2"
+#define CONFIG_SYS_SDIO2 "sdio3"
+#define CONFIG_SYS_SDIO3 "sdio4"
+
+/* I2C Driver */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_KONA
+#define CONFIG_SYS_SPD_BUS_NUM 3 /* Start with PMU bus */
+#define CONFIG_SYS_MAX_I2C_BUS 4
+#define CONFIG_SYS_I2C_BASE0 BSC1_BASE_ADDR
+#define CONFIG_SYS_I2C_BASE1 BSC2_BASE_ADDR
+#define CONFIG_SYS_I2C_BASE2 BSC3_BASE_ADDR
+#define CONFIG_SYS_I2C_BASE3 PMU_BSC_BASE_ADDR
+
+/* Timer Driver */
+#define CONFIG_SYS_TIMER_RATE 32000
+#define CONFIG_SYS_TIMER_COUNTER (TIMER_BASE_ADDR + 4) /* STCLO offset */
+
+/* Init functions */
+#define CONFIG_MISC_INIT_R /* board's misc_init_r function */
+
+/* Some commands use this as the default load address */
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
+
+/* No mtest functions as recommended */
+#undef CONFIG_CMD_MEMORY
+
+/*
+ * This is the initial SP which is used only briefly for relocating the u-boot
+ * image to the top of SDRAM. After relocation u-boot moves the stack to the
+ * proper place.
+ */
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
+
+/* Serial Info */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+/* Post pad 3 bytes after each reg addr */
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK 13000000
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550_COM1 0x3e000000
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_ENV_IS_NOWHERE
+
+#define CONFIG_SYS_NO_FLASH /* Not using NAND/NOR unmanaged flash */
+
+/* console configuration */
+#define CONFIG_SYS_CBSIZE 1024 /* Console buffer size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16) /* Printbuffer size */
+#define CONFIG_SYS_MAXARGS 64
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/*
+ * One partition type must be defined for part.c
+ * This is necessary for the fatls command to work on an SD card
+ * for example.
+ */
+#define CONFIG_DOS_PARTITION
+
+/* version string, parser, etc */
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_LONGHELP
+
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+
+/* Initial upstream - boot to cmd prompt only */
+#define CONFIG_BOOTCOMMAND ""
+
+/* Commands */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_FAT_WRITE
+
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+
+#endif /* __BCM28155_AP_H */
diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h
new file mode 100644
index 0000000..1f57bd2
--- /dev/null
+++ b/include/configs/bur_am335x_common.h
@@ -0,0 +1,197 @@
+/*
+ * bur_am335x_common.h
+ *
+ * common parts used by B&R AM335x based boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> -
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __BUR_AM335X_COMMON_H__
+#define __BUR_AM335X_COMMON_H__
+/* ------------------------------------------------------------------------- */
+#define CONFIG_AM33XX
+#define CONFIG_OMAP
+#define CONFIG_OMAP_COMMON
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_SYS_CACHELINE_SIZE 64
+#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
+
+/* Timer information */
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
+
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_POWER_TPS65217
+
+#define CONFIG_SYS_NO_FLASH /* have no NOR-flash */
+
+#include <asm/arch/omap.h>
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK 48000000
+#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
+#define CONFIG_BAUDRATE 115200
+
+/* Network defines */
+#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */
+#define CONFIG_CMD_DHCP
+#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT 4
+#define CONFIG_CMD_PING
+#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */
+#define CONFIG_MII /* Required in net/eth.c */
+#define CONFIG_SPL_ETH_SUPPORT
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR 1
+#define CONFIG_PHY_NATSEMI
+#define CONFIG_SPL_NET_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */
+#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL"
+
+/*
+ * SPL related defines. The Public RAM memory map the ROM defines the
+ * area between 0x402F0400 and 0x4030B800 as a download area and
+ * 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also
+ * supports X-MODEM loading via UART, and we leverage this and then use
+ * Y-MODEM to load u-boot.img, when booted over UART.
+ */
+#define CONFIG_SPL_TEXT_BASE 0x402F0400
+#define CONFIG_SPL_MAX_SIZE (0x4030B800 - CONFIG_SPL_TEXT_BASE)
+
+/*
+ * Since SPL did pll and ddr initialization for us,
+ * we don't need to do it twice.
+ */
+#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT)
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif /* !CONFIG_SPL_BUILD, ... */
+/*
+ * Our DDR memory always starts at 0x80000000 and U-Boot shall have
+ * relocated itself to higher in memory by the time this value is used.
+ */
+#define CONFIG_SYS_LOAD_ADDR 0x80000000
+/*
+ * ----------------------------------------------------------------------------
+ * DDR information. We say (for simplicity) that we have 1 bank,
+ * always, even when we have more. We always start at 0x80000000,
+ * and we place the initial stack pointer in our SRAM.
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_OMAP24XX
+
+/* GPIO */
+#define CONFIG_OMAP_GPIO
+#define CONFIG_CMD_GPIO
+/*
+ * ----------------------------------------------------------------------------
+ * The following are general good-enough settings for U-Boot. We set a
+ * large malloc pool as we generally have a lot of DDR, and we opt for
+ * function over binary size in the main portion of U-Boot as this is
+ * generally easily constrained later if needed. We enable the config
+ * options that give us information in the environment about what board
+ * we are on so we do not need to rely on the command prompt. We set a
+ * console baudrate of 115200 and use the default baud rate table.
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# "
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */
+
+/* As stated above, the following choices are optional. */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_VERSION_VARIABLE
+
+/* We set the max number of command args high to avoid HUSH bugs. */
+#define CONFIG_SYS_MAXARGS 64
+
+/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 512
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+/*
+ * For commands to use, we take the default list and add a few other
+ * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH
+ * prior to this include, in order to skip a few commands. When we do
+ * have flash, if we expect these commands they must be enabled in that
+ * config. If desired, a specific list of desired commands can be used
+ * instead.
+ */
+#include <config_cmd_default.h>
+/* undefine commands, which we do not need */
+#undef CONFIG_CMD_EDITENV
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_ITEST
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_XIMG
+#undef CONFIG_CMD_CRC32
+/* define command we need always */
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_SOURCE
+
+/*
+ * Our platforms make use of SPL to initalize the hardware (primarily
+ * memory) enough for full U-Boot to be loaded. We also support Falcon
+ * Mode so that the Linux kernel can be booted directly from SPL
+ * instead, if desired. We make use of the general SPL framework found
+ * under common/spl/. Given our generally common memory map, we set a
+ * number of related defaults and sizes here.
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+/*
+ * Place the image at the start of the ROM defined image space.
+ * We limit our size to the ROM-defined downloaded image area, and use the
+ * rest of the space for stack. We load U-Boot itself into memory at
+ * 0x80800000 for legacy reasons (to not conflict with older SPLs). We
+ * have our BSS be placed 1MiB after this, to allow for the default
+ * Linux kernel address of 0x80008000 to work, in the Falcon Mode case.
+ * We have the SPL malloc pool at the end of the BSS area.
+ *
+ * ----------------------------------------------------------------------------
+ */
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+#undef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0x80800000
+#define CONFIG_SPL_BSS_START_ADDR 0x80A00000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
+ CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
+
+/* General parts of the framework, required. */
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_YMODEM_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#endif /* ! __BUR_AM335X_COMMON_H__ */
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index 7729a02..08c67f5 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -45,13 +45,6 @@
#define CONFIG_MISC_INIT_R
#define CONFIG_OF_LIBFDT 1
-/*
- * The early kernel mapping on ARM currently only maps from the base of DRAM
- * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000.
- * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
- * so that leaves DRAM base to DRAM base + 0x4000 available.
- */
-#define CONFIG_SYS_BOOTMAPSZ 0x4000
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h
index 86574c8..c67cf60 100644
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@@ -34,8 +34,19 @@
#define CONFIG_SYS_OMAP_ABE_SYSCK
+/* Define the default GPT table for eMMC */
+#define PARTS_DEFAULT \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
+
#include <configs/ti_omap5_common.h>
+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
/* CPSW Ethernet */
#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */
#define CONFIG_CMD_DHCP
diff --git a/include/configs/kwb.h b/include/configs/kwb.h
new file mode 100644
index 0000000..0f631c0
--- /dev/null
+++ b/include/configs/kwb.h
@@ -0,0 +1,128 @@
+/*
+ * kwb.h
+ *
+ * specific parts for B&R KWB Motherboard
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> -
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_KWB_H__
+#define __CONFIG_KWB_H__
+
+#include <configs/bur_am335x_common.h>
+/* ------------------------------------------------------------------------- */
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK)
+
+#define CONFIG_POWER_TPS65217
+
+#define CONFIG_MACH_TYPE 3589
+/* I2C IP block */
+#define CONFIG_SYS_OMAP24_I2C_SPEED_PSOC 20000
+
+/* GPIO */
+#define CONFIG_SPL_GPIO_SUPPORT
+
+/* MMC/SD IP block */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_CMD_MMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+/* RAW SD card / eMMC locations. */
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SPL_MMC_SUPPORT
+
+#undef CONFIG_SPL_OS_BOOT
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000
+
+/* RAW SD card / eMMC */
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
+
+#endif /* CONFIG_SPL_OS_BOOT */
+
+/* Always 128 KiB env size */
+#define CONFIG_ENV_SIZE (128 << 10)
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "autoload=0\0" \
+ "loadaddr=0x80100000\0" \
+ "bootfile=arimg\0" \
+ "usbboot=echo Booting from USB-Stick ...; " \
+ "usb start; " \
+ "fatload usb 0 ${loadaddr} ${bootfile}; " \
+ "usb stop; " \
+ "go ${loadaddr};\0" \
+ "netboot=echo Booting from network ...; " \
+ "setenv autoload 0; " \
+ "dhcp; " \
+ "tftp ${loadaddr} arimg; " \
+ "go ${loadaddr}\0" \
+ "usbupdate=echo Updating UBOOT from USB-Stick ...; " \
+ "usb start; " \
+ "fatload usb 0 0x80000000 updateubootusb.img; " \
+ "source;\0" \
+ "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \
+ "setenv autoload 0; " \
+ "dhcp;" \
+ "tftp 0x80000000 updateUBOOT.img;" \
+ "source;\0"
+#endif /* !CONFIG_SPL_BUILD*/
+
+#define CONFIG_BOOTCOMMAND \
+ "run usbupdate;"
+#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */
+
+/* undefine command which we not need here */
+#undef CONFIG_BOOTM_LINUX
+#undef CONFIG_BOOTM_NETBSD
+#undef CONFIG_BOOTM_PLAN9
+#undef CONFIG_BOOTM_RTEMS
+#undef CONFIG_GZIP
+#undef CONFIG_ZLIB
+#undef CONFIG_CMD_CRC32
+
+/* USB configuration */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT
+/* attention! not only for gadget, enables also highspeed in hostmode */
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_MUSB_HOST
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE MUSB_HOST
+
+#ifdef CONFIG_MUSB_HOST
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#endif /* CONFIG_MUSB_HOST */
+
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1
+#define CONFIG_SYS_MMC_ENV_PART 2
+#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+/*
+ * Common filesystems support. When we have removable storage we
+ * enabled a number of useful commands and support.
+ */
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+#define CONFIG_FAT_WRITE
+#define CONFIG_CMD_FS_GENERIC
+#endif /* CONFIG_MMC, ... */
+
+#endif /* ! __CONFIG_TSERIES_H__ */
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index dcd29ce..7c5c2f4 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -98,6 +98,7 @@
/* EHCI */
#define CONFIG_USB_STORAGE
+#define CONFIG_OMAP3_GPIO_2
#define CONFIG_OMAP3_GPIO_5
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_OMAP
@@ -263,10 +264,9 @@
"${mtdparts} " \
"vram=6M omapfb.vram=1:2M,2:2M,3:2M " \
"omapdss.def_disp=lcd;" \
- "bootm 0x82000000 0x84000000\0"
-
-#define CONFIG_BOOTCOMMAND \
- "run nandboot"
+ "bootm 0x82000000 0x84000000\0" \
+ "bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;" \
+ "then source 82000000;else run nandboot;fi\0"
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
@@ -395,6 +395,7 @@
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
+#define CONFIG_SPL_NAND_SOFTECC
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h
new file mode 100644
index 0000000..5a55556
--- /dev/null
+++ b/include/configs/pengwyn.h
@@ -0,0 +1,208 @@
+/*
+ * pengwyn.h
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * based on am335x_evm.h, Copyright (C) 2011 Texas Instruments Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_PENGWYN_H
+#define __CONFIG_PENGWYN_H
+
+#define CONFIG_NAND
+#define CONFIG_SERIAL1
+#define CONFIG_CONS_INDEX 1
+
+#include <configs/ti_am335x_common.h>
+
+/* Clock Defines */
+#define V_OSCK 24000000
+#define V_SCLK V_OSCK
+
+/* set env size */
+#define CONFIG_ENV_SIZE 0x4000
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x80200000\0" \
+ "fdtaddr=0x80F80000\0" \
+ "bootpart=0:2\0" \
+ "bootdir=/boot\0" \
+ "bootfile=zImage\0" \
+ "fdtfile=am335x-pengwyn.dtb\0" \
+ "console=ttyO0,115200n8\0" \
+ "optargs=\0" \
+ "mmcdev=0\0" \
+ "mmcroot=/dev/mmcblk0p2 ro\0" \
+ "mmcrootfstype=ext4 rootwait\0" \
+ "rootpath=/export/rootfs\0" \
+ "nfsopts=nolock\0" \
+ "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
+ "::off\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "netargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=/dev/nfs " \
+ "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
+ "ip=dhcp\0" \
+ "bootenv=uEnv.txt\0" \
+ "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
+ "importbootenv=echo Importing environment from mmc ...; " \
+ "env import -t $loadaddr $filesize\0" \
+ "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
+ "mmcloados=run mmcargs; " \
+ "bootz ${loadaddr} - ${fdtaddr};\0" \
+ "mmcboot=mmc dev ${mmcdev}; " \
+ "if mmc rescan; then " \
+ "echo SD/MMC found on device ${mmcdev};" \
+ "if run loadbootenv; then " \
+ "echo Loaded environment from ${bootenv};" \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "if run loadimage; then " \
+ "run loadfdt;" \
+ "run mmcloados;" \
+ "fi;" \
+ "fi;\0" \
+ "netboot=echo Booting from network ...; " \
+ "setenv autoload no; " \
+ "dhcp; " \
+ "tftp ${loadaddr} ${bootfile}; " \
+ "tftp ${fdtaddr} ${fdtfile}; " \
+ "run netargs; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0" \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \
+ "nandrootfstype=ubifs rootwait=1\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${fdtaddr} u-boot-spl-os; " \
+ "nand read ${loadaddr} kernel; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0"
+#endif
+
+#define CONFIG_BOOTCOMMAND \
+ "run mmcboot;" \
+ "run nandboot;"
+
+/* NS16550 Configuration: primary UART via FDTI */
+#define CONFIG_SYS_NS16550_COM1 0x44e09000
+#define CONFIG_BAUDRATE 115200
+
+/* I2C Configuration */
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_CMD_EEPROM
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+
+/* SPL */
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_YMODEM_SUPPORT
+
+/* General network SPL */
+#define CONFIG_SPL_NET_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL"
+
+/* NAND support */
+#define CONFIG_CMD_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, \
+ 18, 19, 20, 21, 22, 23, 24, 25, \
+ 26, 27, 28, 29, 30, 31, 32, 33, \
+ 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 14
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+#define GPMC_NAND_ECC_LP_x8_LAYOUT 1
+#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \
+ "128k(SPL.backup1)," \
+ "128k(SPL.backup2)," \
+ "128k(SPL.backup3),1792k(u-boot)," \
+ "128k(u-boot-spl-os)," \
+ "128k(u-boot-env),5m(kernel),-(rootfs)"
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+
+/*
+ * USB configuration. We enable MUSB support, both for host and for
+ * gadget. We set USB0 as peripheral and USB1 as host, based on the
+ * board schematic and physical port wired to each. Then for host we
+ * add mass storage support.
+ */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_MUSB_GADGET
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+#define CONFIG_MUSB_HOST
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+
+#if defined(CONFIG_MUSB_HOST)
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#endif
+
+#if defined(CONFIG_SPL_BUILD)
+/* disable host part of MUSB in SPL */
+#undef CONFIG_MUSB_HOST
+/* Disable CPSW SPL support so we fit within the 101KiB limit. */
+#undef CONFIG_SPL_ETH_SUPPORT
+#endif
+
+/* Network */
+#define CONFIG_CMD_MII
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR 1
+#define CONFIG_PHY_RESET 1
+#define CONFIG_PHY_NATSEMI
+
+/* CPSW support */
+#define CONFIG_SPL_ETH_SUPPORT
+
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#endif /* ! __CONFIG_PENGWYN_H */
diff --git a/include/configs/rpi_b.h b/include/configs/rpi_b.h
index 976ceaa..6306d61 100644
--- a/include/configs/rpi_b.h
+++ b/include/configs/rpi_b.h
@@ -95,12 +95,25 @@
#define CONFIG_SYS_LOAD_ADDR 0x1000000
#define CONFIG_CONSOLE_MUX
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_PREBOOT \
+ "if load mmc 0:1 ${loadaddr} /uEnv.txt; then " \
+ "env import -t ${loadaddr} ${filesize}; " \
+ "fi"
+
+#define ENV_DEVICE_SETTINGS \
+ "stdin=serial,lcd\0" \
+ "stdout=serial,lcd\0" \
+ "stderr=serial,lcd\0"
+
/*
* Memory layout for where various images get loaded by boot scripts:
*
* scriptaddr can be pretty much anywhere that doesn't conflict with something
* else. Put it low in memory to avoid conflicts.
*
+ * pxefile_addr_r can be pretty much anywhere that doesn't conflict with
+ * something else. Put it low in memory to avoid conflicts.
+ *
* kernel_addr_r must be within the first 128M of RAM in order for the
* kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will
* decompress itself to 0x8000 after the start of RAM, kernel_addr_r
@@ -116,68 +129,112 @@
* ramdisk_addr_r simply shouldn't overlap anything else. Choosing 33M allows
* for the FDT/DTB to be up to 1M, which is hopefully plenty.
*/
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "stdin=serial\0" \
- "stderr=serial,lcd\0" \
- "stdout=serial,lcd\0" \
+#define ENV_MEM_LAYOUT_SETTINGS \
"scriptaddr=0x00000000\0" \
+ "pxefile_addr_r=0x00100000\0" \
"kernel_addr_r=0x01000000\0" \
"fdt_addr_r=0x02000000\0" \
"fdtfile=bcm2835-rpi-b.dtb\0" \
"ramdisk_addr_r=0x02100000\0" \
- "boot_targets=mmc0\0" \
- \
- "script_boot=" \
- "if fatload ${devtype} ${devnum}:1 " \
- "${scriptaddr} boot.scr.uimg; then " \
- "source ${scriptaddr}; " \
- "fi;\0" \
- \
+
+#define BOOTCMDS_MMC \
"mmc_boot=" \
"setenv devtype mmc; " \
"if mmc dev ${devnum}; then " \
- "run script_boot; " \
+ "run scan_boot; " \
"fi\0" \
+ "bootcmd_mmc0=setenv devnum 0; run mmc_boot;\0"
+#define BOOT_TARGETS_MMC "mmc0"
+
+#define BOOTCMDS_COMMON \
+ "rootpart=1\0" \
\
- "bootcmd_mmc0=setenv devnum 0; run mmc_boot\0" \
+ "do_script_boot=" \
+ "load ${devtype} ${devnum}:${rootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "source ${scriptaddr}\0" \
+ \
+ "script_boot=" \
+ "for script in ${boot_scripts}; do " \
+ "if test -e ${devtype} ${devnum}:${rootpart} " \
+ "${prefix}${script}; then " \
+ "echo Found ${prefix}${script}; " \
+ "run do_script_boot; " \
+ "echo SCRIPT FAILED: continuing...; " \
+ "fi; " \
+ "done\0" \
+ \
+ "do_sysboot_boot=" \
+ "sysboot ${devtype} ${devnum}:${rootpart} any " \
+ "${scriptaddr} ${prefix}extlinux/extlinux.conf\0" \
+ \
+ "sysboot_boot=" \
+ "if test -e ${devtype} ${devnum}:${rootpart} " \
+ "${prefix}extlinux/extlinux.conf; then " \
+ "echo Found ${prefix}extlinux/extlinux.conf; " \
+ "run do_sysboot_boot; " \
+ "echo SCRIPT FAILED: continuing...; " \
+ "fi\0" \
+ \
+ "scan_boot=" \
+ "echo Scanning ${devtype} ${devnum}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run sysboot_boot; " \
+ "run script_boot; " \
+ "done\0" \
+ \
+ "boot_targets=" \
+ BOOT_TARGETS_MMC " " \
+ "\0" \
+ \
+ "boot_prefixes=/\0" \
+ \
+ "boot_scripts=boot.scr.uimg\0" \
+ \
+ BOOTCMDS_MMC
#define CONFIG_BOOTCOMMAND \
"for target in ${boot_targets}; do run bootcmd_${target}; done"
-#define CONFIG_BOOTDELAY 2
+#define CONFIG_BOOTCOMMAND \
+ "for target in ${boot_targets}; do run bootcmd_${target}; done"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ ENV_DEVICE_SETTINGS \
+ ENV_MEM_LAYOUT_SETTINGS \
+ BOOTCMDS_COMMON
+
+#define CONFIG_BOOTDELAY 2
/* Shell */
-#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_MAXARGS 8
#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
#define CONFIG_COMMAND_HISTORY
-#define CONFIG_AUTO_COMPLETE
/* Commands */
#include <config_cmd_default.h>
-#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_GPIO
#define CONFIG_CMD_MMC
-#define CONFIG_DOS_PARTITION
#define CONFIG_PARTITION_UUIDS
#define CONFIG_CMD_PART
-#define CONFIG_CMD_FS_GENERIC
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT
-/* Some things don't make sense on this HW or yet */
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SAVEENV
-/* Device tree support for bootm/bootz */
-#define CONFIG_OF_LIBFDT
+/* Device tree support */
#define CONFIG_OF_BOARD_SETUP
/* ATAGs support for bootm/bootz */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_CMDLINE_TAG
#define CONFIG_INITRD_TAG
+#include <config_distro_defaults.h>
+
+/* Some things don't make sense on this HW or yet */
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SAVEENV
+#undef CONFIG_CMD_DHCP
+#undef CONFIG_CMD_MII
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_PING
+
#endif
diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h
index 9abfe82..9c04c23 100644
--- a/include/configs/tao3530.h
+++ b/include/configs/tao3530.h
@@ -83,6 +83,13 @@
#define CONFIG_OMAP_HSMMC
#define CONFIG_DOS_PARTITION
+/* GPIO banks */
+#define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */
+#define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */
+#define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */
+#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
+#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
+
/* commands to include */
#include <config_cmd_default.h>
diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h
index 91f97dd..7e9ca01 100644
--- a/include/configs/ti_am335x_common.h
+++ b/include/configs/ti_am335x_common.h
@@ -13,7 +13,6 @@
#define __CONFIG_TI_AM335X_COMMON_H__
#define CONFIG_AM33XX
-#define CONFIG_BOARD_LATE_INIT
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h
index 2f0e4c0..bcb5eab 100644
--- a/include/configs/ti_omap4_common.h
+++ b/include/configs/ti_omap4_common.h
@@ -163,4 +163,10 @@
#define CONFIG_SPL_NAND_AM33XX_BCH /* ELM support */
#endif
+#ifdef CONFIG_SPL_BUILD
+/* No need for i2c in SPL mode as we will use SRI2C for PMIC access on OMAP4 */
+#undef CONFIG_SYS_I2C
+#undef CONFIG_SYS_I2C_OMAP24XX
+#endif
+
#endif /* __CONFIG_TI_OMAP4_COMMON_H */
diff --git a/include/configs/tseries.h b/include/configs/tseries.h
new file mode 100644
index 0000000..8fb87ac
--- /dev/null
+++ b/include/configs/tseries.h
@@ -0,0 +1,265 @@
+/*
+ * tseries.h
+ *
+ * specific parts for B&R T-Series Motherboard
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> -
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_TSERIES_H__
+#define __CONFIG_TSERIES_H__
+
+#include <configs/bur_am335x_common.h>
+/* ------------------------------------------------------------------------- */
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK)
+
+#define CONFIG_POWER_TPS65217
+
+/* Support both device trees and ATAGs. */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMD_BOOTZ
+/*#define CONFIG_MACH_TYPE 3589*/
+#define CONFIG_MACH_TYPE 0xFFFFFFFF /* TODO: check with kernel*/
+
+/* MMC/SD IP block */
+#if defined(CONFIG_EMMC_BOOT)
+ #define CONFIG_MMC
+ #define CONFIG_GENERIC_MMC
+ #define CONFIG_OMAP_HSMMC
+ #define CONFIG_CMD_MMC
+ #define CONFIG_SUPPORT_EMMC_BOOT
+/* RAW SD card / eMMC locations. */
+ #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */
+ #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+ #define CONFIG_SPL_MMC_SUPPORT
+#endif /* CONFIG_EMMC_BOOT */
+
+/*
+ * When we have SPI or NAND flash we expect to be making use of mtdparts,
+ * both for ease of use in U-Boot and for passing information on to
+ * the Linux kernel.
+ */
+#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND)
+#define CONFIG_MTD_DEVICE /* Required for mtdparts */
+#define CONFIG_CMD_MTDPARTS
+#endif /* CONFIG_SPI_BOOT, ... */
+
+#undef CONFIG_SPL_OS_BOOT
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000
+
+/* RAW SD card / eMMC */
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
+
+/* NAND */
+#ifdef CONFIG_NAND
+#define CONFIG_CMD_SPL_NAND_OFS 0x080000 /* end of u-boot */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x140000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif /* CONFIG_NAND */
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#endif /* CONFIG_NAND */
+
+/* Always 128 KiB env size */
+#define CONFIG_ENV_SIZE (128 << 10)
+
+#ifdef CONFIG_NAND
+#define NANDARGS \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "nandroot=ubi0:rootfs rw ubi.mtd=8,2048\0" \
+ "nandrootfstype=ubifs rootwait=1\0" \
+ "nandimgsize=0x500000\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} kernel ${nandimgsize}; " \
+ "bootz ${loadaddr}\0"
+#else
+#define NANDARGS ""
+#endif /* CONFIG_NAND */
+
+#ifdef CONFIG_MMC
+#define MMCARGS \
+ "silent=1\0"
+#else
+#define MMCARGS ""
+#endif /* CONFIG_MMC */
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "autoload=0\0" \
+ "loadaddr=0x80200000\0" \
+ "bootfile=zImage\0" \
+ "console=ttyO0,115200n8\0" \
+ "optargs=\0" \
+ "rootpath=/tftpboot/tseries/rootfs-small\0" \
+ "nfsopts=nolock\0" \
+ "netargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=/dev/nfs " \
+ "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
+ "ip=dhcp\0" \
+ "netboot=echo Booting from network ...; " \
+ "setenv autoload no; " \
+ "dhcp; " \
+ "tftp ${loadaddr} ${bootfile}; " \
+ "run netargs; " \
+ "bootm ${loadaddr}\0" \
+ "usbupdate=echo Updating UBOOT from USB-Stick ...; " \
+ "usb start; " \
+ "fatload usb 0 0x80000000 updateubootusb.img; " \
+ "source;\0" \
+ "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \
+ "setenv autoload 0; " \
+ "dhcp;" \
+ "tftp 0x80000000 updateUBOOT.img;" \
+ "source;\0" \
+ NANDARGS \
+ MMCARGS
+#endif /* !CONFIG_SPL_BUILD*/
+
+#define CONFIG_BOOTCOMMAND \
+ "run mmcboot1;"
+#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */
+
+#ifdef CONFIG_NAND
+/*
+ * GPMC block. We support 1 device and the physical address to
+ * access CS0 at is 0x8000000.
+ */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x8000000
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_CMD_NAND
+/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, \
+ 18, 19, 20, 21, 22, 23, 24, 25, \
+ 26, 27, 28, 29, 30, 31, 32, 33, \
+ 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 14
+
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
+ "128k(SPL)," \
+ "128k(SPL.backup1)," \
+ "128k(SPL.backup2)," \
+ "128k(SPL.backup3)," \
+ "512k(u-boot)," \
+ "128k(u-boot-spl-os)," \
+ "128k(u-boot-env)," \
+ "5m(kernel),"\
+ "-(rootfs)"
+#endif /* CONFIG_NAND */
+
+/* USB configuration */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT
+/* attention! not only for gadget, enables also highspeed in hostmode */
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_MUSB_HOST
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE MUSB_HOST
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+
+#ifdef CONFIG_MUSB_HOST
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#endif /* CONFIG_MUSB_HOST */
+
+#if defined(CONFIG_SPI_BOOT)
+/* McSPI IP block */
+#define CONFIG_SPI
+#define CONFIG_OMAP3_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SF_DEFAULT_SPEED 24000000
+
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS 0
+#define CONFIG_SPL_SPI_CS 0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */
+#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */
+#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */
+
+#elif defined(CONFIG_EMMC_BOOT)
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1
+#define CONFIG_SYS_MMC_ENV_PART 2
+#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#elif defined(CONFIG_NAND)
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x120000 /* TODO: Adresse definieren */
+#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE
+#else
+#error "no storage for Environment defined!"
+#endif
+/*
+ * Common filesystems support. When we have removable storage we
+ * enabled a number of useful commands and support.
+ */
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+#define CONFIG_FAT_WRITE
+#define CONFIG_CMD_FS_GENERIC
+#endif /* CONFIG_MMC, ... */
+
+#endif /* ! __CONFIG_TSERIES_H__ */
diff --git a/lib/Makefile b/lib/Makefile
index 8c483c9..dedb97b 100644
--- a/lib/Makefile
+++ b/lib/Makefile
@@ -65,6 +65,3 @@
obj-$(CONFIG_RANDOM_MACADDR) += rand.o
obj-$(CONFIG_BOOTP_RANDOM_DELAY) += rand.o
obj-$(CONFIG_CMD_LINK_LOCAL) += rand.o
-
-# SEE README.arm-unaligned-accesses
-CFLAGS_bzlib.o := $(PLATFORM_NO_UNALIGNED)
diff --git a/scripts/checkpatch.pl b/scripts/checkpatch.pl
index 88c5bc7..df0820c 100755
--- a/scripts/checkpatch.pl
+++ b/scripts/checkpatch.pl
@@ -3331,6 +3331,11 @@
WARN("PREFER_PACKED",
"__packed is preferred over __attribute__((packed))\n" . $herecurr);
}
+# Check for new packed members, warn to use care
+ if ($line =~ /\b(__attribute__\s*\(\s*\(.*\bpacked|__packed)\b/) {
+ WARN("NEW_PACKED",
+ "Adding new packed members is to be done with care\n" . $herecurr);
+ }
# Check for __attribute__ aligned, prefer __aligned
if ($line =~ /\b__attribute__\s*\(\s*\(.*aligned/) {