arm: octeontx2: Add dtsi/dts files for Octeon TX2 CN913x DB
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN913x DB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 2538dd3..9c601a5 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -237,6 +237,12 @@
armada-xp-maxbcm.dtb \
armada-xp-synology-ds414.dtb \
armada-xp-theadorable.dtb \
+ cn9130-db-A.dtb \
+ cn9130-db-B.dtb \
+ cn9131-db-A.dtb \
+ cn9131-db-B.dtb \
+ cn9132-db-A.dtb \
+ cn9132-db-B.dtb \
cn9130-crb-A.dtb \
cn9130-crb-B.dtb
diff --git a/arch/arm/dts/cn9130-db-A.dts b/arch/arm/dts/cn9130-db-A.dts
new file mode 100644
index 0000000..90d6e4a
--- /dev/null
+++ b/arch/arm/dts/cn9130-db-A.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#include "cn9130-db.dtsi"
+
+/ {
+ model = "Marvell CN9130 development board (CP NOR) setup(A)";
+
+ aliases {
+ spi0 = &cp0_spi1;
+ };
+};
+
+/*
+ * CP related configuration
+ */
+&cp0_pinctl {
+ /* MPP Bus:
+ * [0-11] RGMII1
+ * [12] GPIO GE-IN
+ * [13-16] SPI1
+ * [17-27] NAND
+ * [28] MSS_GPIO[5] XXX:(mode nr from a3900)
+ * [29-30] SATA
+ * [31] MSS_GPIO[4] XXX:(mode nr from a3900)
+ * [32,34] SMI
+ * [33] SDIO
+ * [35-36] I2C1
+ * [37-38] I2C0
+ * [39-43] SDIOctrl
+ * [44-55] RGMII2
+ * [56-62] SDIO
+ */
+
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 3 3 3 3 3 3 3 3 3 3
+ 3 3 0 3 3 3 3 1 1 1
+ 1 1 1 1 1 1 1 1 3 9
+ 9 3 7 6 7 2 2 2 2 1
+ 1 1 1 1 1 1 1 1 1 1
+ 1 1 1 1 1 1 0xe 0xe 0xe 0xe
+ 0xe 0xe 0xe>;
+};
+
+/* U54 */
+&cp0_nand {
+ status = "disabled";
+};
+
+/* U55 */
+&cp0_spi1 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/cn9130-db-B.dts b/arch/arm/dts/cn9130-db-B.dts
new file mode 100644
index 0000000..fb52aa8
--- /dev/null
+++ b/arch/arm/dts/cn9130-db-B.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#include "cn9130-db.dtsi"
+
+/ {
+ model = "Marvell CN9130 development board (CP NAND) setup(B)";
+};
+
+/*
+ * CP related configuration
+ */
+&cp0_pinctl {
+ /* MPP Bus:
+ * [0-11] RGMII1
+ * [12] GPIO GE-IN
+ * [13-14] SPI1
+ * [15-27] NAND
+ * [28] MSS_GPIO[5] XXX:(mode nr from a3900)
+ * [29-30] SATA
+ * [31] MSS_GPIO[4] XXX:(mode nr from a3900)
+ * [32,34] SMI
+ * [33] SDIO
+ * [35-36] I2C1
+ * [37-38] I2C0
+ * [39-43] SDIOctrl
+ * [44-55] RGMII2
+ * [56-62] SDIO
+ */
+
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 3 3 3 3 3 3 3 3 3 3
+ 3 3 0 2 3 1 1 1 1 1
+ 1 1 1 1 1 1 1 1 3 9
+ 9 3 7 6 7 2 2 2 2 1
+ 1 1 1 1 1 1 1 1 1 1
+ 1 1 1 1 1 1 0xe 0xe 0xe 0xe
+ 0xe 0xe 0xe>;
+};
+
+/* U54 */
+&cp0_nand {
+ status = "okay";
+};
+
+/* U55 */
+&cp0_spi1 {
+ status = "disabled";
+};
diff --git a/arch/arm/dts/cn9130-db-dev-info.dtsi b/arch/arm/dts/cn9130-db-dev-info.dtsi
new file mode 100644
index 0000000..68e9c0b
--- /dev/null
+++ b/arch/arm/dts/cn9130-db-dev-info.dtsi
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+/ {
+ /* This should go only into devel boards */
+ compatible = "marvell,cp110";
+ sar {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sar_fields {
+ compatible = "marvell,sample-at-reset";
+ reg = <0x4c 0x4e>;
+ chip_count = <2>;
+ bit_width = <5>;
+ freq {
+ key = "freq";
+ description = "CPU/DDR and PIDI frequencies";
+ start-bit = <0>;
+ bit-length = <4>;
+ option-cnt = <3>;
+ options = "0x0", "CPU/DDR = 0x0: 2000/1200 Mhz, PIDI = 0: 1Ghz",
+ "0x2", "CPU/DDR = 0x6: 2200/1200 Mhz, PIDI = 0: 1Ghz",
+ "0x4", "CPU/DDR = 0xD: 1600/1200 Mhz, PIDI = 0: 1Ghz";
+ default = <0x2>;
+ status = "okay";
+ };
+ boot_mode {
+ key = "boot_mode";
+ description = "Boot mode options";
+ start-bit = <4>;
+ bit-length = <6>;
+ option-cnt = <4>;
+ options = "0xE", "CP0_NAND PIDI BW-8bit, PS-4KB, ECC-4bit\t(supported configuration: B)",
+ "0xF", "CP0_NAND PIDI BW-8bit, PS-4KB, ECC-8bit\t(supported configuration: B)",
+ "0x2A", "AP_EMMC",
+ "0x32", "CP1_SPI_1 24bits";
+ default = <0x32>;
+ status = "okay";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/cn9130-db.dtsi b/arch/arm/dts/cn9130-db.dtsi
new file mode 100644
index 0000000..1b28732
--- /dev/null
+++ b/arch/arm/dts/cn9130-db.dtsi
@@ -0,0 +1,316 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#include "cn9130.dtsi" /* include SoC device tree */
+#include "cn9130-db-dev-info.dtsi"
+
+/ {
+ model = "DB-CN-9130";
+ compatible = "marvell,cn9130-db", "marvell,cn91xx", "marvell,cn9030-vd",
+ "marvell,cn9030", "marvell,armada-ap806-quad",
+ "marvell,armada-ap806";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ i2c0 = &cp0_i2c0;
+ gpio0 = &ap_gpio0;
+ gpio1 = &cp0_gpio0;
+ gpio2 = &cp0_gpio1;
+ };
+
+ memory@00000000 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ cp0 {
+ config-space {
+ i2c@701000 {
+ /* U36 */
+ expander0: pca953x@21 {
+ compatible = "nxp,pca9555";
+ #gpio-cells = <2>;
+ reg = <0x21>;
+ status = "okay";
+ };
+ };
+ sdhci@780000 {
+ vqmmc-supply = <&cp0_reg_sd_vccq>;
+ vmmc-supply = <&cp0_reg_sd_vcc>;
+ };
+
+ ap_reg_mmc_vccq: ap_mmc_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "ap_mmc_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+ cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <100000>;
+ regulator-force-boot-off;
+ gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <100000>;
+ regulator-force-boot-off;
+ gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
+ };
+ cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "cp0_sd_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+ cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0_sd_vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+ cp0_reg_usb3_current_lim0:cp0_usb3_current_limiter@0 {
+ compatible = "regulator-fixed";
+ regulator-min-microamp = <900000>;
+ regulator-max-microamp = <900000>;
+ regulator-force-boot-off;
+ gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_reg_usb3_current_lim1: cp0_usb3_current_limiter@1 {
+ compatible = "regulator-fixed";
+ regulator-min-microamp = <900000>;
+ regulator-max-microamp = <900000>;
+ regulator-force-boot-off;
+ gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/*
+ * AP related configuration
+ */
+&ap_pinctl {
+ /* MPP Bus:
+ * SDIO [0-10, 12]
+ * UART0 [11,19]
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 1 1 1 1 1 1 1 1 1 1
+ 1 3 1 0 0 0 0 0 0 3 >;
+};
+
+/* on-board eMMC - U9 */
+&ap_sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ap_emmc_pins>;
+ vqmmc-supply = <&ap_reg_mmc_vccq>;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ status = "okay";
+};
+
+/*
+ * CP related configuration
+ */
+&cp0_pinctl {
+ cp0_nand_pins: cp0-nand-pins {
+ marvell,pins = <15 16 17 18 19 20 21 22 23 24 25 26 27 >;
+ marvell,function = <1>;
+ };
+ cp0_nand_rb: cp0-nand-rb {
+ marvell,pins = < 13 >;
+ marvell,function = <2>;
+ };
+};
+
+/*
+ * CP0
+ */
+&cp0_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&cp0_i2c1 {
+ status = "okay";
+};
+
+/* CON 28 */
+&cp0_sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_sdhci_pins>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+/* U54 */
+&cp0_nand {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_nand_pins &cp0_nand_rb>;
+ status = "disabled";
+};
+
+/* U55 */
+&cp0_spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi0_pins>;
+ reg = <0x700680 0x50>, /* control */
+ <0x2000000 0x1000000>, /* CS0 */
+ <0 0xffffffff>, /* CS1 */
+ <0 0xffffffff>, /* CS2 */
+ <0 0xffffffff>; /* CS3 */
+ status = "disabled";
+
+ spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor", "spi-flash";
+ reg = <0x0>;
+ /* On-board MUX does not allow higher frequencies */
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0x0 0x200000>;
+ };
+
+ partition@400000 {
+ label = "Filesystem";
+ reg = <0x200000 0xe00000>;
+ };
+ };
+ };
+};
+
+&cp0_comphy {
+ phy0 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+
+ phy1 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+
+ phy2 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+
+ phy3 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+
+ phy4 {
+ phy-type = <COMPHY_TYPE_SFI0>;
+ phy-speed = <COMPHY_SPEED_10_3125G>;
+ };
+
+ phy5 {
+ phy-type = <COMPHY_TYPE_SATA1>;
+ };
+};
+
+/* SLM-1521-V2, CON6 */
+&cp0_pcie0 {
+ num-lanes = <4>;
+ status = "disabled";
+};
+
+&cp0_mdio {
+ status = "okay";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp0_eth0 {
+ status = "okay";
+ phy-mode = "sfi";
+};
+
+/* CON56 */
+&cp0_eth1 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+/* CON57 */
+&cp0_eth2 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+};
+
+/* SLM-1521-V2, CON2 */
+&cp0_sata0 {
+ status = "okay";
+};
+
+&cp0_utmi0 {
+ status = "okay";
+};
+
+&cp0_utmi1 {
+ status = "okay";
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+ vbus-supply = <&cp0_reg_usb3_vbus0>;
+ current-limiter = <&cp0_reg_usb3_current_lim0>;
+ vbus-disable-delay = <500>;
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+ vbus-supply = <&cp0_reg_usb3_vbus1>;
+ current-limiter = <&cp0_reg_usb3_current_lim1>;
+ vbus-disable-delay = <500>;
+};
+
+&cp0_pcie0 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/cn9131-db-A.dts b/arch/arm/dts/cn9131-db-A.dts
new file mode 100644
index 0000000..81aff17
--- /dev/null
+++ b/arch/arm/dts/cn9131-db-A.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#include "cn9130-db-A.dts"
+#include "cn9131-db.dtsi"
+
+/ {
+ model = "Marvell CN9131 development board (CP NOR) setup(A)";
+ compatible = "marvell,cn9131-db", "marvell,armada-ap806-quad",
+ "marvell,armada-ap806";
+};
+
+&cp1_comphy {
+ /* Serdes Configuration:
+ * Lane 0: PCIe0 (x2)
+ * Lane 1: PCIe0 (x2)
+ * Lane 2: unconnected
+ * Lane 3: USB1
+ * Lane 4: SFP (port 0)
+ * Lane 5: SATA1
+ */
+ phy0 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+ phy1 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+ phy2 {
+ phy-type = <COMPHY_TYPE_UNCONNECTED>;
+ };
+ phy3 {
+ phy-type = <COMPHY_TYPE_USB3_HOST1>;
+ };
+ phy4 {
+ phy-type = <COMPHY_TYPE_SFI0>;
+ phy-speed = <COMPHY_SPEED_10_3125G>;
+ };
+ phy5 {
+ phy-type = <COMPHY_TYPE_SATA1>;
+ };
+};
+
+&cp1_ethernet {
+ status = "okay";
+};
+
+/* CON50 */
+&cp1_eth0 {
+ status = "okay";
+ phy-mode = "sfi"; /* lane-4 */
+ marvell,sfp-tx-disable-gpio = <&cp1_gpio0 9 GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm/dts/cn9131-db-B.dts b/arch/arm/dts/cn9131-db-B.dts
new file mode 100644
index 0000000..0269183
--- /dev/null
+++ b/arch/arm/dts/cn9131-db-B.dts
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#include "cn9130-db-B.dts"
+#include "cn9131-db.dtsi"
+
+/ {
+ model = "Marvell CN9131 development board (CP NAND) setup(B)";
+ compatible = "marvell,cn9131-db", "marvell,armada-ap806-quad",
+ "marvell,armada-ap806";
+};
+
+&cp1_comphy {
+ /* Serdes Configuration:
+ * Lane 0: PCIe0 (x2)
+ * Lane 1: PCIe0 (x2)
+ * Lane 2: SFI (port 0)
+ * Lane 3: USB1
+ * Lane 4: SGMII (port 1)
+ * Lane 5: SATA1
+ */
+ phy0 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+ phy1 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+ phy2 {
+ phy-type = <COMPHY_TYPE_SFI0>;
+ phy-speed = <COMPHY_SPEED_10_3125G>;
+ };
+ phy3 {
+ phy-type = <COMPHY_TYPE_USB3_HOST1>;
+ };
+ phy4 {
+ phy-type = <COMPHY_TYPE_SGMII1>;
+ phy-speed = <COMPHY_SPEED_1_25G>;
+ };
+ phy5 {
+ phy-type = <COMPHY_TYPE_SATA1>;
+ };
+};
+
+&cp1_ethernet {
+ status = "okay";
+};
+
+/* 3310 RJ45 CON55 */
+&cp1_eth0 {
+ status = "okay";
+ phy-mode = "sfi"; /* lane-2 */
+ phy = <&sfi_phy8>; /* required by 3310 fw download */
+};
+
+/* CON50 */
+&cp1_eth1 {
+ status = "okay";
+ phy-mode = "sgmii"; /* lane-4 */
+ marvell,sfp-tx-disable-gpio = <&cp1_gpio0 9 GPIO_ACTIVE_HIGH>;
+};
+
+&cp1_xmdio {
+ status = "okay";
+ sfi_phy8: ethernet-phy@8 {
+ reg = <8>;
+ };
+};
diff --git a/arch/arm/dts/cn9131-db.dtsi b/arch/arm/dts/cn9131-db.dtsi
new file mode 100644
index 0000000..5057605
--- /dev/null
+++ b/arch/arm/dts/cn9131-db.dtsi
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#undef CP110_NAME
+#undef CP110_NUM
+#undef CP110_PCIE_MEM_SIZE
+#undef CP110_PCIEx_CPU_MEM_BASE
+#undef CP110_PCIEx_BUS_MEM_BASE
+
+/* CP110-1 Settings */
+#define CP110_NAME cp1
+#define CP110_NUM 1
+#define CP110_PCIE_MEM_SIZE(iface) (0xf00000)
+#define CP110_PCIEx_CPU_MEM_BASE(iface) (0xe2000000 + (iface) * 0x1000000)
+#define CP110_PCIEx_BUS_MEM_BASE(iface) (CP110_PCIEx_CPU_MEM_BASE(iface))
+
+#include "armada-cp110.dtsi"
+
+/ {
+ model = "Marvell CN9131 development board";
+ compatible = "marvell,cn9131-db";
+
+ aliases {
+ gpio3 = &cp1_gpio0;
+ gpio4 = &cp1_gpio1;
+ };
+
+ cp1 {
+ config-space {
+ cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_xhci0_vbus_pins>;
+ regulator-name = "cp1-xhci0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <100000>;
+ regulator-force-boot-off;
+ gpio = <&cp1_gpio0 3 GPIO_ACTIVE_HIGH>;
+ };
+ cp1_reg_usb3_current_lim0: cp1_usb3_current_limiter@0 {
+ compatible = "regulator-fixed";
+ regulator-min-microamp = <900000>;
+ regulator-max-microamp = <900000>;
+ regulator-force-boot-off;
+ gpio = <&cp1_gpio0 2 GPIO_ACTIVE_HIGH>;
+ };
+ cp1_pcie_reset_pins: cp1-pcie-reset-pins {
+ marvell,pins = <0>;
+ marvell,function = <0>;
+ };
+ };
+ };
+};
+
+&cp1_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+/* CON40 */
+&cp1_pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_pcie_reset_pins>;
+ marvell,reset-gpio = <&cp1_gpio0 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ num-lanes = <2>;
+ /* non-prefetchable memory */
+ ranges = <0x82000000 0 0xe2000000 0 0xe2000000 0 0xf00000>;
+};
+
+&cp1_pinctl {
+ compatible = "marvell,mvebu-pinctrl",
+ "marvell,cp115-standalone-pinctrl";
+ bank-name ="cp1-110";
+
+ /* MPP Bus:
+ * [0-12] GPIO
+ * [13-16] SPI1
+ * [17-27] GPIO (Default)
+ * [28] SATA1_PRESENT_ACTIVEn
+ * [29-34] GPIO (Default)
+ * [35-36] xSMI
+ * [37-38] I2C0
+ * [39-62] GPIO
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
+ 0x0 0x0 0x0 0x3 0x3 0x3 0x3 0x0 0x0 0x0
+ 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x9 0x0
+ 0x0 0x0 0x0 0x0 0x0 0x7 0x7 0x2 0x2 0x0
+ 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
+ 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
+ 0x0 0x0 0x0 >;
+
+ cp1_i2c0_pins: cp1-i2c-pins-0 {
+ marvell,pins = < 37 38 >;
+ marvell,function = <2>;
+ };
+ cp1_spi0_pins: cp1-spi-pins-0 {
+ marvell,pins = < 13 14 15 16 >;
+ marvell,function = <3>;
+ };
+ cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
+ marvell,pins = <3>;
+ marvell,function = <0>;
+ };
+};
+
+/* CON32 */
+&cp1_sata0 {
+ status = "okay";
+};
+
+/* U24 */
+&cp1_spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp1_spi0_pins>;
+ reg = <0x700680 0x50>, /* control */
+ <0x2000000 0x1000000>, /* CS0 */
+ <0 0xffffffff>, /* CS1 */
+ <0 0xffffffff>, /* CS2 */
+ <0 0xffffffff>; /* CS3 */
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor", "spi-flash";
+ reg = <0x0>;
+ /* On-board MUX does not allow higher frequencies */
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0x0 0x200000>;
+ };
+
+ partition@400000 {
+ label = "Filesystem";
+ reg = <0x200000 0xe00000>;
+ };
+ };
+ };
+};
+
+/* CON58 */
+&cp1_usb3_1 {
+ vbus-supply = <&cp1_reg_usb3_vbus0>;
+ current-limiter = <&cp1_reg_usb3_current_lim0>;
+ vbus-disable-delay = <500>;
+ status = "okay";
+};
+
+&cp1_utmi1 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/cn9132-db-A.dts b/arch/arm/dts/cn9132-db-A.dts
new file mode 100644
index 0000000..ba9b8a2
--- /dev/null
+++ b/arch/arm/dts/cn9132-db-A.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#include "cn9131-db-A.dts"
+#include "cn9132-db.dtsi"
+
+/ {
+ model = "Marvell CN9132 development board (CP NOR) setup(A)";
+ compatible = "marvell,cn9132-db", "marvell,armada-ap806-quad",
+ "marvell,armada-ap806";
+};
diff --git a/arch/arm/dts/cn9132-db-B.dts b/arch/arm/dts/cn9132-db-B.dts
new file mode 100644
index 0000000..e126e23
--- /dev/null
+++ b/arch/arm/dts/cn9132-db-B.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#include "cn9131-db-B.dts"
+#include "cn9132-db.dtsi"
+
+/ {
+ model = "Marvell CN9132 development board (CP NAND) setup(B)";
+ compatible = "marvell,cn9132-db-B", "marvell,armada-ap806-quad",
+ "marvell,armada-ap806";
+};
diff --git a/arch/arm/dts/cn9132-db.dtsi b/arch/arm/dts/cn9132-db.dtsi
new file mode 100644
index 0000000..d51a4d0
--- /dev/null
+++ b/arch/arm/dts/cn9132-db.dtsi
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018-2021 Marvell International Ltd.
+ */
+
+#undef CP110_NAME
+#undef CP110_NUM
+#undef CP110_PCIE_MEM_SIZE
+#undef CP110_PCIEx_CPU_MEM_BASE
+#undef CP110_PCIEx_BUS_MEM_BASE
+
+/* CP110-2 Settings */
+#define CP110_NAME cp2
+#define CP110_NUM 2
+#define CP110_PCIE_MEM_SIZE(iface) (0xf00000)
+#define CP110_PCIEx_CPU_MEM_BASE(iface) (0xe5000000 + (iface) * 0x1000000)
+#define CP110_PCIEx_BUS_MEM_BASE(iface) (CP110_PCIEx_CPU_MEM_BASE(iface))
+
+#include "armada-cp110.dtsi"
+
+/ {
+ model = "Marvell CN9132 development board";
+ compatible = "marvell,cn9132-db";
+
+ aliases {
+ gpio5 = &cp2_gpio0;
+ gpio6 = &cp2_gpio1;
+ };
+
+ cp2 {
+ config-space {
+ sdhci@780000 {
+ vqmmc-supply = <&cp2_reg_sd_vccq>;
+ };
+
+ cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp2-xhci0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <100000>;
+ regulator-force-boot-off;
+ gpio = <&cp2_gpio0 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp2-xhci1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <100000>;
+ regulator-force-boot-off;
+ gpio = <&cp2_gpio0 3 GPIO_ACTIVE_HIGH>;
+ };
+ cp2_reg_sd_vccq: cp2_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "cp2_sd_vcc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ /* cp2_mpp49 */
+ gpios = <&cp2_gpio1 17 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+ cp2_reg_usb3_current_lim0: cp2_usb3_current_limiter@0 {
+ compatible = "regulator-fixed";
+ regulator-min-microamp = <900000>;
+ regulator-max-microamp = <900000>;
+ regulator-force-boot-off;
+ gpio = <&cp2_gpio0 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp2_reg_usb3_current_lim1: cp2_usb3_current_limiter@1 {
+ compatible = "regulator-fixed";
+ regulator-min-microamp = <900000>;
+ regulator-max-microamp = <900000>;
+ regulator-force-boot-off;
+ gpio = <&cp2_gpio0 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
+
+&cp2_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp2_i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&cp2_pinctl {
+ compatible = "marvell,mvebu-pinctrl",
+ "marvell,cp115-standalone-pinctrl";
+ bank-name ="cp2-110";
+
+ /* MPP Bus:
+ * [0-26] GPIO
+ * [27] SATA0_PRESENT_ACTIVEn
+ * [28] SATA1_PRESENT_ACTIVEn
+ * [29-31, 33] GPIO (Default)
+ * [32,34] SMI
+ * [37-38] I2C0
+ * [39-53] GPIO
+ * [54] SD_CRD_RSTn (out)
+ * [55] SD_CRD_DT (in)
+ * [56-62] SDIO
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
+ 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
+ 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x9 0x9 0x0
+ 0x0 0x0 0x8 0x0 0x8 0x0 0x0 0x2 0x2 0x0
+ 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
+ 0x0 0x0 0x0 0x0 0xa 0xb 0xe 0xe 0xe 0xe
+ 0xe 0xe 0xe >;
+
+ cp2_i2c0_pins: cp2-i2c-pins-0 {
+ marvell,pins = < 37 38 >;
+ marvell,function = <2>;
+ };
+
+ cp2_sdhci_pins: cp2-sdhi-pins-0 {
+ marvell,pins = < 56 57 58 59 60 61 >;
+ marvell,function = <14>;
+ };
+};
+
+&cp2_usb3_0 {
+ status = "okay";
+ vbus-supply = <&cp2_reg_usb3_vbus0>;
+ current-limiter = <&cp2_reg_usb3_current_lim0>;
+ vbus-disable-delay = <500>;
+};
+
+/* SLM-1521-V2, CON11 */
+&cp2_usb3_1 {
+ status = "okay";
+ vbus-supply = <&cp2_reg_usb3_vbus1>;
+ current-limiter = <&cp2_reg_usb3_current_lim1>;
+ vbus-disable-delay = <500>;
+ status = "okay";
+};
+
+&cp2_utmi0 {
+ status = "okay";
+};
+
+&cp2_utmi1 {
+ status = "okay";
+};
+
+&cp2_comphy {
+ phy0 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+
+ phy1 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+
+ phy2 {
+ phy-type = <COMPHY_TYPE_SATA0>;
+ };
+
+ phy3 {
+ phy-type = <COMPHY_TYPE_USB3_HOST1>;
+ };
+
+ phy4 {
+ phy-type = <COMPHY_TYPE_SFI0>;
+ phy-speed = <COMPHY_SPEED_10_3125G>;
+ };
+
+ phy5 {
+ phy-type = <COMPHY_TYPE_PEX2>;
+ };
+};
+
+&cp2_ethernet {
+ status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp2_eth0 {
+ status = "okay";
+ phy-mode = "sfi";
+};
+
+/* SLM-1521-V2, CON6 */
+&cp2_pcie0 {
+ /* non-prefetchable memory */
+ ranges =<0x82000000 0 0xe5000000 0 0xe5000000 0 0x1000000>;
+ num-lanes = <2>;
+ status = "okay";
+};
+
+/* SLM-1521-V2, CON8 */
+&cp2_pcie2 {
+ num-lanes = <1>;
+ status = "okay";
+};
+
+&cp2_pinctl {
+};
+
+/* SLM-1521-V2, CON4 */
+&cp2_sata0 {
+ status = "okay";
+};
+
+/* CON 2 on SLM-1683 - microSD */
+&cp2_sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp2_sdhci_pins>;
+ bus-width = <4>;
+ status = "okay";
+};