ARM: ts4800: add ethernet support
This commit adds ethernet support to the TS4800. Note that the
MAC address is not fused on this board and have to be read from
FEC PALR PAUR registers (this is how the kernel provided by
Technologic Systems does it).
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
diff --git a/board/technologic/ts4800/ts4800.c b/board/technologic/ts4800/ts4800.c
index 0a8d43e..6ef15e1 100644
--- a/board/technologic/ts4800/ts4800.c
+++ b/board/technologic/ts4800/ts4800.c
@@ -21,6 +21,9 @@
#include <fsl_esdhc.h>
#include <mc13892.h>
+#include <malloc.h>
+#include <netdev.h>
+#include <phy.h>
#include "ts4800.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -62,6 +65,36 @@
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
+static void setup_iomux_fec(void)
+{
+ static const iomux_v3_cfg_t fec_pads[] = {
+ NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO,
+ PAD_CTL_HYS |
+ PAD_CTL_PUS_22K_UP |
+ PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
+ MX51_PAD_EIM_EB3__FEC_RDATA1,
+ NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, PAD_CTL_HYS),
+ MX51_PAD_EIM_CS3__FEC_RDATA3,
+ MX51_PAD_NANDF_CS2__FEC_TX_ER,
+ MX51_PAD_EIM_CS5__FEC_CRS,
+ MX51_PAD_EIM_CS4__FEC_RX_ER,
+ /* PAD used on TS4800 */
+ MX51_PAD_DI2_PIN2__FEC_MDC,
+ MX51_PAD_DISP2_DAT14__FEC_RDAT0,
+ MX51_PAD_DISP2_DAT10__FEC_COL,
+ MX51_PAD_DISP2_DAT11__FEC_RXCLK,
+ MX51_PAD_DISP2_DAT15__FEC_TDAT0,
+ MX51_PAD_DISP2_DAT6__FEC_TDAT1,
+ MX51_PAD_DISP2_DAT7__FEC_TDAT2,
+ MX51_PAD_DISP2_DAT8__FEC_TDAT3,
+ MX51_PAD_DISP2_DAT9__FEC_TX_EN,
+ MX51_PAD_DISP2_DAT13__FEC_TX_CLK,
+ MX51_PAD_DISP2_DAT12__FEC_RX_DV,
+ };
+
+ imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
+}
+
#ifdef CONFIG_FSL_ESDHC
int board_mmc_getcd(struct mmc *mmc)
{
@@ -113,6 +146,7 @@
int board_early_init_f(void)
{
setup_iomux_uart();
+ setup_iomux_fec();
return 0;
}
@@ -126,6 +160,75 @@
}
/*
+ * Read the MAC address from FEC's registers PALR PAUR.
+ * User is supposed to configure these registers when MAC address is known
+ * from another source (fuse), but on TS4800, MAC address is not fused and
+ * the bootrom configure these registers on startup.
+ */
+static int fec_get_mac_from_register(uint32_t base_addr)
+{
+ unsigned char ethaddr[6];
+ u32 reg_mac[2];
+ int i;
+
+ reg_mac[0] = in_be32(base_addr + 0xE4);
+ reg_mac[1] = in_be32(base_addr + 0xE8);
+
+ for(i = 0; i < 6; i++)
+ ethaddr[i] = (reg_mac[i / 4] >> ((i % 4) * 8)) & 0xFF;
+
+ if (is_valid_ethaddr(ethaddr)) {
+ eth_setenv_enetaddr("ethaddr", ethaddr);
+ return 0;
+ }
+
+ return -1;
+}
+
+#define TS4800_GPIO_FEC_PHY_RES IMX_GPIO_NR(2, 14)
+int board_eth_init(bd_t *bd)
+{
+ int dev_id = -1;
+ int phy_id = 0xFF;
+ uint32_t addr = IMX_FEC_BASE;
+
+ uint32_t base_mii;
+ struct mii_dev *bus = NULL;
+ struct phy_device *phydev = NULL;
+ int ret;
+
+ /* reset FEC phy */
+ imx_iomux_v3_setup_pad(MX51_PAD_EIM_A20__GPIO2_14);
+ gpio_direction_output(TS4800_GPIO_FEC_PHY_RES, 0);
+ mdelay(1);
+ gpio_set_value(TS4800_GPIO_FEC_PHY_RES, 1);
+ mdelay(1);
+
+ base_mii = addr;
+ debug("eth_init: fec_probe(bd, %i, %i) @ %08x\n", dev_id, phy_id, addr);
+ bus = fec_get_miibus(base_mii, dev_id);
+ if (!bus)
+ return -ENOMEM;
+
+ phydev = phy_find_by_mask(bus, phy_id, PHY_INTERFACE_MODE_MII);
+ if (!phydev) {
+ free(bus);
+ return -ENOMEM;
+ }
+
+ if (fec_get_mac_from_register(addr))
+ printf("eth_init: failed to get MAC address\n");
+
+ ret = fec_probe(bd, dev_id, addr, bus, phydev);
+ if (ret) {
+ free(phydev);
+ free(bus);
+ }
+
+ return ret;
+}
+
+/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/