| if ARCH_SUNXI |
| |
| config IDENT_STRING |
| default " Allwinner Technology" |
| |
| config DRAM_SUN4I |
| bool |
| help |
| Select this dram controller driver for Sun4/5/7i platforms, |
| like A10/A13/A20. |
| |
| config DRAM_SUN6I |
| bool |
| help |
| Select this dram controller driver for Sun6i platforms, |
| like A31/A31s. |
| |
| config DRAM_SUN8I_A23 |
| bool |
| help |
| Select this dram controller driver for Sun8i platforms, |
| for A23 SOC. |
| |
| config DRAM_SUN8I_A33 |
| bool |
| help |
| Select this dram controller driver for Sun8i platforms, |
| for A33 SOC. |
| |
| config DRAM_SUN8I_A83T |
| bool |
| help |
| Select this dram controller driver for Sun8i platforms, |
| for A83T SOC. |
| |
| config DRAM_SUN9I |
| bool |
| help |
| Select this dram controller driver for Sun9i platforms, |
| like A80. |
| |
| config DRAM_SUN50I_H6 |
| bool |
| help |
| Select this dram controller driver for some sun50i platforms, |
| like H6. |
| |
| config DRAM_SUN50I_H616 |
| bool |
| help |
| Select this dram controller driver for some sun50i platforms, |
| like H616. |
| |
| if DRAM_SUN50I_H616 |
| config DRAM_SUN50I_H616_WRITE_LEVELING |
| bool "H616 DRAM write leveling" |
| ---help--- |
| Select this when DRAM on your H616 board needs write leveling. |
| |
| config DRAM_SUN50I_H616_READ_CALIBRATION |
| bool "H616 DRAM read calibration" |
| ---help--- |
| Select this when DRAM on your H616 board needs read calibration. |
| |
| config DRAM_SUN50I_H616_READ_TRAINING |
| bool "H616 DRAM read training" |
| ---help--- |
| Select this when DRAM on your H616 board needs read training. |
| |
| config DRAM_SUN50I_H616_WRITE_TRAINING |
| bool "H616 DRAM write training" |
| ---help--- |
| Select this when DRAM on your H616 board needs write training. |
| |
| config DRAM_SUN50I_H616_BIT_DELAY_COMPENSATION |
| bool "H616 DRAM bit delay compensation" |
| ---help--- |
| Select this when DRAM on your H616 board needs bit delay |
| compensation. |
| |
| config DRAM_SUN50I_H616_UNKNOWN_FEATURE |
| bool "H616 DRAM unknown feature" |
| ---help--- |
| Select this when DRAM on your H616 board needs this unknown |
| feature. |
| |
| config DRAM_SUN50I_H616_DX_ODT |
| hex "H616 DRAM DX ODT parameter" |
| help |
| DX ODT value from vendor DRAM settings. |
| |
| config DRAM_SUN50I_H616_DX_DRI |
| hex "H616 DRAM DX DRI parameter" |
| help |
| DX DRI value from vendor DRAM settings. |
| |
| config DRAM_SUN50I_H616_CA_DRI |
| hex "H616 DRAM CA DRI parameter" |
| help |
| CA DRI value from vendor DRAM settings. |
| endif |
| |
| config SUN6I_PRCM |
| bool |
| help |
| Support for the PRCM (Power/Reset/Clock Management) unit available |
| in A31 SoC. |
| |
| config AXP_PMIC_BUS |
| bool |
| select DM_PMIC if DM_I2C |
| select PMIC_AXP if DM_I2C |
| help |
| Select this PMIC bus access helpers for Sunxi platform PRCM or other |
| AXP family PMIC devices. |
| |
| config SUNXI_SRAM_ADDRESS |
| hex |
| default 0x10000 if MACH_SUN9I || MACH_SUN50I || MACH_SUN50I_H5 |
| default 0x20000 if SUN50I_GEN_H6 |
| default 0x0 |
| ---help--- |
| Older Allwinner SoCs have their mask boot ROM mapped just below 4GB, |
| with the first SRAM region being located at address 0. |
| Some newer SoCs map the boot ROM at address 0 instead and move the |
| SRAM to a different address. |
| |
| config SUNXI_A64_TIMER_ERRATUM |
| bool |
| |
| # Note only one of these may be selected at a time! But hidden choices are |
| # not supported by Kconfig |
| config SUNXI_GEN_SUN4I |
| bool |
| ---help--- |
| Select this for sunxi SoCs which have resets and clocks set up |
| as the original A10 (mach-sun4i). |
| |
| config SUNXI_GEN_SUN6I |
| bool |
| ---help--- |
| Select this for sunxi SoCs which have sun6i like periphery, like |
| separate ahb reset control registers, custom pmic bus, new style |
| watchdog, etc. |
| |
| config SUN50I_GEN_H6 |
| bool |
| select FIT |
| select SPL_LOAD_FIT |
| select MMC_SUNXI_HAS_NEW_MODE |
| select SUPPORT_SPL |
| ---help--- |
| Select this for sunxi SoCs which have H6 like peripherals, clocks |
| and memory map. |
| |
| config SUNXI_DRAM_DW |
| bool |
| ---help--- |
| Select this for sunxi SoCs which uses a DRAM controller like the |
| DesignWare controller used in H3, mainly SoCs after H3, which do |
| not have official open-source DRAM initialization code, but can |
| use modified H3 DRAM initialization code. |
| |
| if SUNXI_DRAM_DW |
| config SUNXI_DRAM_DW_16BIT |
| bool |
| ---help--- |
| Select this for sunxi SoCs with DesignWare DRAM controller and |
| have only 16-bit memory buswidth. |
| |
| config SUNXI_DRAM_DW_32BIT |
| bool |
| ---help--- |
| Select this for sunxi SoCs with DesignWare DRAM controller with |
| 32-bit memory buswidth. |
| endif |
| |
| config MACH_SUNXI_H3_H5 |
| bool |
| select PHY_SUN4I_USB |
| select SUNXI_DE2 |
| select SUNXI_DRAM_DW |
| select SUNXI_DRAM_DW_32BIT |
| select SUNXI_GEN_SUN6I |
| select SUPPORT_SPL |
| |
| # TODO: try out A80's 8GiB DRAM space |
| config SUNXI_DRAM_MAX_SIZE |
| hex |
| default 0x100000000 if MACH_SUN50I_H616 |
| default 0xC0000000 if MACH_SUN50I || MACH_SUN50I_H5 || MACH_SUN50I_H6 |
| default 0x80000000 |
| |
| choice |
| prompt "Sunxi SoC Variant" |
| optional |
| |
| config MACH_SUNIV |
| bool "suniv (Allwinner F1C100s/F1C200s/F1C600/R6)" |
| select CPU_ARM926EJS |
| select SUNXI_GEN_SUN6I |
| select SUPPORT_SPL |
| select SKIP_LOWLEVEL_INIT_ONLY |
| select SPL_SKIP_LOWLEVEL_INIT_ONLY |
| |
| config MACH_SUN4I |
| bool "sun4i (Allwinner A10)" |
| select CPU_V7A |
| select PHY_SUN4I_USB |
| select DRAM_SUN4I |
| select SUNXI_GEN_SUN4I |
| select SUPPORT_SPL |
| imply SPL_SYS_I2C_LEGACY |
| imply SYS_I2C_LEGACY |
| |
| config MACH_SUN5I |
| bool "sun5i (Allwinner A13)" |
| select CPU_V7A |
| select DRAM_SUN4I |
| select PHY_SUN4I_USB |
| select SUNXI_GEN_SUN4I |
| select SUPPORT_SPL |
| imply SPL_SYS_I2C_LEGACY |
| imply SYS_I2C_LEGACY |
| |
| config MACH_SUN6I |
| bool "sun6i (Allwinner A31)" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select ARCH_SUPPORT_PSCI |
| select SPL_ARMV7_SET_CORTEX_SMPEN |
| select DRAM_SUN6I |
| select PHY_SUN4I_USB |
| select SPL_I2C |
| select SUN6I_PRCM |
| select SUNXI_GEN_SUN6I |
| select SUPPORT_SPL |
| select SYS_I2C_SUN6I_P2WI |
| select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT |
| |
| config MACH_SUN7I |
| bool "sun7i (Allwinner A20)" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select ARCH_SUPPORT_PSCI |
| select SPL_ARMV7_SET_CORTEX_SMPEN |
| select DRAM_SUN4I |
| select PHY_SUN4I_USB |
| select SUNXI_GEN_SUN4I |
| select SUPPORT_SPL |
| select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT |
| imply SPL_SYS_I2C_LEGACY |
| imply SYS_I2C_LEGACY |
| |
| config MACH_SUN8I_A23 |
| bool "sun8i (Allwinner A23)" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select ARCH_SUPPORT_PSCI |
| select DRAM_SUN8I_A23 |
| select PHY_SUN4I_USB |
| select SPL_I2C |
| select SUNXI_GEN_SUN6I |
| select SUPPORT_SPL |
| select SYS_I2C_SUN8I_RSB |
| select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT |
| |
| config MACH_SUN8I_A33 |
| bool "sun8i (Allwinner A33)" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select ARCH_SUPPORT_PSCI |
| select DRAM_SUN8I_A33 |
| select PHY_SUN4I_USB |
| select SPL_I2C |
| select SUNXI_GEN_SUN6I |
| select SUPPORT_SPL |
| select SYS_I2C_SUN8I_RSB |
| select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT |
| |
| config MACH_SUN8I_A83T |
| bool "sun8i (Allwinner A83T)" |
| select CPU_V7A |
| select DRAM_SUN8I_A83T |
| select PHY_SUN4I_USB |
| select SPL_I2C |
| select SUNXI_GEN_SUN6I |
| select MMC_SUNXI_HAS_NEW_MODE |
| select MMC_SUNXI_HAS_MODE_SWITCH |
| select SUPPORT_SPL |
| select SYS_I2C_SUN8I_RSB |
| |
| config MACH_SUN8I_H3 |
| bool "sun8i (Allwinner H3)" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select ARCH_SUPPORT_PSCI |
| select MACH_SUNXI_H3_H5 |
| select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT |
| |
| config MACH_SUN8I_R40 |
| bool "sun8i (Allwinner R40)" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select ARCH_SUPPORT_PSCI |
| select SUNXI_GEN_SUN6I |
| select MMC_SUNXI_HAS_NEW_MODE |
| select SUPPORT_SPL |
| select SUNXI_DRAM_DW |
| select SUNXI_DRAM_DW_32BIT |
| select PHY_SUN4I_USB |
| imply SPL_SYS_I2C_LEGACY |
| |
| config MACH_SUN8I_V3S |
| bool "sun8i (Allwinner V3/V3s/S3/S3L)" |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select ARCH_SUPPORT_PSCI |
| select SUNXI_GEN_SUN6I |
| select SUNXI_DRAM_DW |
| select SUNXI_DRAM_DW_16BIT |
| select SUPPORT_SPL |
| select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT |
| |
| config MACH_SUN9I |
| bool "sun9i (Allwinner A80)" |
| select CPU_V7A |
| select SPL_ARMV7_SET_CORTEX_SMPEN |
| select DRAM_SUN9I |
| select SPL_I2C |
| select SUN6I_PRCM |
| select SUNXI_GEN_SUN6I |
| select SUPPORT_SPL |
| |
| config MACH_SUN50I |
| bool "sun50i (Allwinner A64)" |
| select ARM64 |
| select PHY_SUN4I_USB |
| select SUN6I_PRCM |
| select SUNXI_DE2 |
| select SUNXI_GEN_SUN6I |
| select MMC_SUNXI_HAS_NEW_MODE |
| select SUPPORT_SPL |
| select SUNXI_DRAM_DW |
| select SUNXI_DRAM_DW_32BIT |
| select FIT |
| select SPL_LOAD_FIT |
| select SUNXI_A64_TIMER_ERRATUM |
| |
| config MACH_SUN50I_H5 |
| bool "sun50i (Allwinner H5)" |
| select ARM64 |
| select MACH_SUNXI_H3_H5 |
| select MMC_SUNXI_HAS_NEW_MODE |
| select FIT |
| select SPL_LOAD_FIT |
| |
| config MACH_SUN50I_H6 |
| bool "sun50i (Allwinner H6)" |
| select ARM64 |
| select PHY_SUN4I_USB |
| select DRAM_SUN50I_H6 |
| select SUN50I_GEN_H6 |
| |
| config MACH_SUN50I_H616 |
| bool "sun50i (Allwinner H616)" |
| select ARM64 |
| select DRAM_SUN50I_H616 |
| select SUN50I_GEN_H6 |
| |
| endchoice |
| |
| # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" |
| config MACH_SUN8I |
| bool |
| select SPL_ARMV7_SET_CORTEX_SMPEN if !ARM64 |
| select SUN6I_PRCM |
| default y if MACH_SUN8I_A23 |
| default y if MACH_SUN8I_A33 |
| default y if MACH_SUN8I_A83T |
| default y if MACH_SUNXI_H3_H5 |
| default y if MACH_SUN8I_R40 |
| default y if MACH_SUN8I_V3S |
| |
| config RESERVE_ALLWINNER_BOOT0_HEADER |
| bool "reserve space for Allwinner boot0 header" |
| select ENABLE_ARM_SOC_BOOT0_HOOK |
| ---help--- |
| Prepend a 1536 byte (empty) header to the U-Boot image file, to be |
| filled with magic values post build. The Allwinner provided boot0 |
| blob relies on this information to load and execute U-Boot. |
| Only needed on 64-bit Allwinner boards so far when using boot0. |
| |
| config ARM_BOOT_HOOK_RMR |
| bool |
| depends on ARM64 |
| default y |
| select ENABLE_ARM_SOC_BOOT0_HOOK |
| ---help--- |
| Insert some ARM32 code at the very beginning of the U-Boot binary |
| which uses an RMR register write to bring the core into AArch64 mode. |
| The very first instruction acts as a switch, since it's carefully |
| chosen to be a NOP in one mode and a branch in the other, so the |
| code would only be executed if not already in AArch64. |
| This allows both the SPL and the U-Boot proper to be entered in |
| either mode and switch to AArch64 if needed. |
| |
| if SUNXI_DRAM_DW || DRAM_SUN50I_H6 |
| config SUNXI_DRAM_DDR3 |
| bool |
| |
| config SUNXI_DRAM_DDR2 |
| bool |
| |
| config SUNXI_DRAM_LPDDR3 |
| bool |
| |
| choice |
| prompt "DRAM Type and Timing" |
| default SUNXI_DRAM_DDR3_1333 if !MACH_SUN8I_V3S |
| default SUNXI_DRAM_DDR2_V3S if MACH_SUN8I_V3S |
| |
| config SUNXI_DRAM_DDR3_1333 |
| bool "DDR3 1333" |
| select SUNXI_DRAM_DDR3 |
| ---help--- |
| This option is the original only supported memory type, which suits |
| many H3/H5/A64 boards available now. |
| |
| config SUNXI_DRAM_LPDDR3_STOCK |
| bool "LPDDR3 with Allwinner stock configuration" |
| select SUNXI_DRAM_LPDDR3 |
| ---help--- |
| This option is the LPDDR3 timing used by the stock boot0 by |
| Allwinner. |
| |
| config SUNXI_DRAM_H6_LPDDR3 |
| bool "LPDDR3 DRAM chips on the H6 DRAM controller" |
| select SUNXI_DRAM_LPDDR3 |
| depends on DRAM_SUN50I_H6 |
| ---help--- |
| This option is the LPDDR3 timing used by the stock boot0 by |
| Allwinner. |
| |
| config SUNXI_DRAM_H6_DDR3_1333 |
| bool "DDR3-1333 boot0 timings on the H6 DRAM controller" |
| select SUNXI_DRAM_DDR3 |
| depends on DRAM_SUN50I_H6 |
| ---help--- |
| This option is the DDR3 timing used by the boot0 on H6 TV boxes |
| which use a DDR3-1333 timing. |
| |
| config SUNXI_DRAM_DDR2_V3S |
| bool "DDR2 found in V3s chip" |
| select SUNXI_DRAM_DDR2 |
| depends on MACH_SUN8I_V3S |
| ---help--- |
| This option is only for the DDR2 memory chip which is co-packaged in |
| Allwinner V3s SoC. |
| |
| endchoice |
| endif |
| |
| config DRAM_TYPE |
| int "sunxi dram type" |
| depends on MACH_SUN8I_A83T |
| default 3 |
| ---help--- |
| Set the dram type, 3: DDR3, 7: LPDDR3 |
| |
| config DRAM_CLK |
| int "sunxi dram clock speed" |
| default 792 if MACH_SUN9I |
| default 648 if MACH_SUN8I_R40 |
| default 312 if MACH_SUN6I || MACH_SUN8I |
| default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || \ |
| MACH_SUN8I_V3S |
| default 672 if MACH_SUN50I |
| default 744 if MACH_SUN50I_H6 |
| default 720 if MACH_SUN50I_H616 |
| ---help--- |
| Set the dram clock speed, valid range 240 - 480 (prior to sun9i), |
| must be a multiple of 24. For the sun9i (A80), the tested values |
| (for DDR3-1600) are 312 to 792. |
| |
| if MACH_SUN5I || MACH_SUN7I |
| config DRAM_MBUS_CLK |
| int "sunxi mbus clock speed" |
| default 300 |
| ---help--- |
| Set the mbus clock speed. The maximum on sun5i hardware is 300MHz. |
| |
| endif |
| |
| config DRAM_ZQ |
| int "sunxi dram zq value" |
| depends on !MACH_SUN50I_H616 |
| default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || \ |
| MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_A83T |
| default 127 if MACH_SUN7I |
| default 14779 if MACH_SUN8I_V3S |
| default 3881979 if MACH_SUNXI_H3_H5 || MACH_SUN8I_R40 || MACH_SUN50I_H6 |
| default 4145117 if MACH_SUN9I |
| default 3881915 if MACH_SUN50I |
| ---help--- |
| Set the dram zq value. |
| |
| config DRAM_ODT_EN |
| bool "sunxi dram odt enable" |
| default y if MACH_SUN8I_A23 |
| default y if MACH_SUNXI_H3_H5 |
| default y if MACH_SUN8I_R40 |
| default y if MACH_SUN50I |
| default y if MACH_SUN50I_H6 |
| default y if MACH_SUN50I_H616 |
| ---help--- |
| Select this to enable dram odt (on die termination). |
| |
| if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I |
| config DRAM_EMR1 |
| int "sunxi dram emr1 value" |
| default 0 if MACH_SUN4I |
| default 4 if MACH_SUN5I || MACH_SUN7I |
| ---help--- |
| Set the dram controller emr1 value. |
| |
| config DRAM_TPR3 |
| hex "sunxi dram tpr3 value" |
| default 0 |
| ---help--- |
| Set the dram controller tpr3 parameter. This parameter configures |
| the delay on the command lane and also phase shifts, which are |
| applied for sampling incoming read data. The default value 0 |
| means that no phase/delay adjustments are necessary. Properly |
| configuring this parameter increases reliability at high DRAM |
| clock speeds. |
| |
| config DRAM_DQS_GATING_DELAY |
| hex "sunxi dram dqs_gating_delay value" |
| default 0 |
| ---help--- |
| Set the dram controller dqs_gating_delay parmeter. Each byte |
| encodes the DQS gating delay for each byte lane. The delay |
| granularity is 1/4 cycle. For example, the value 0x05060606 |
| means that the delay is 5 quarter-cycles for one lane (1.25 |
| cycles) and 6 quarter-cycles (1.5 cycles) for 3 other lanes. |
| The default value 0 means autodetection. The results of hardware |
| autodetection are not very reliable and depend on the chip |
| temperature (sometimes producing different results on cold start |
| and warm reboot). But the accuracy of hardware autodetection |
| is usually good enough, unless running at really high DRAM |
| clocks speeds (up to 600MHz). If unsure, keep as 0. |
| |
| choice |
| prompt "sunxi dram timings" |
| default DRAM_TIMINGS_VENDOR_MAGIC |
| ---help--- |
| Select the timings of the DDR3 chips. |
| |
| config DRAM_TIMINGS_VENDOR_MAGIC |
| bool "Magic vendor timings from Android" |
| ---help--- |
| The same DRAM timings as in the Allwinner boot0 bootloader. |
| |
| config DRAM_TIMINGS_DDR3_1066F_1333H |
| bool "JEDEC DDR3-1333H with down binning to DDR3-1066F" |
| ---help--- |
| Use the timings of the standard JEDEC DDR3-1066F speed bin for |
| DRAM_CLK <= 533MHz and the timings of the DDR3-1333H speed bin |
| for DRAM_CLK > 533MHz. This covers the majority of DDR3 chips |
| used in Allwinner A10/A13/A20 devices. In the case of DDR3-1333 |
| or DDR3-1600 chips, be sure to check the DRAM datasheet to confirm |
| that down binning to DDR3-1066F is supported (because DDR3-1066F |
| uses a bit faster timings than DDR3-1333H). |
| |
| config DRAM_TIMINGS_DDR3_800E_1066G_1333J |
| bool "JEDEC DDR3-800E / DDR3-1066G / DDR3-1333J" |
| ---help--- |
| Use the timings of the slowest possible JEDEC speed bin for the |
| selected DRAM_CLK. Depending on the DRAM_CLK value, it may be |
| DDR3-800E, DDR3-1066G or DDR3-1333J. |
| |
| endchoice |
| |
| endif |
| |
| if MACH_SUN8I_A23 |
| config DRAM_ODT_CORRECTION |
| int "sunxi dram odt correction value" |
| default 0 |
| ---help--- |
| Set the dram odt correction value (range -255 - 255). In allwinner |
| fex files, this option is found in bits 8-15 of the u32 odt_en variable |
| in the [dram] section. When bit 31 of the odt_en variable is set |
| then the correction is negative. Usually the value for this is 0. |
| endif |
| |
| config SYS_CLK_FREQ |
| default 408000000 if MACH_SUNIV |
| default 1008000000 if MACH_SUN4I |
| default 1008000000 if MACH_SUN5I |
| default 1008000000 if MACH_SUN6I |
| default 912000000 if MACH_SUN7I |
| default 816000000 if MACH_SUN50I || MACH_SUN50I_H5 |
| default 1008000000 if MACH_SUN8I |
| default 1008000000 if MACH_SUN9I |
| default 888000000 if MACH_SUN50I_H6 |
| default 1008000000 if MACH_SUN50I_H616 |
| |
| config SYS_CONFIG_NAME |
| default "suniv" if MACH_SUNIV |
| default "sun4i" if MACH_SUN4I |
| default "sun5i" if MACH_SUN5I |
| default "sun6i" if MACH_SUN6I |
| default "sun7i" if MACH_SUN7I |
| default "sun8i" if MACH_SUN8I |
| default "sun9i" if MACH_SUN9I |
| default "sun50i" if MACH_SUN50I |
| default "sun50i" if MACH_SUN50I_H6 |
| default "sun50i" if MACH_SUN50I_H616 |
| |
| config SYS_BOARD |
| default "sunxi" |
| |
| config SYS_SOC |
| default "sunxi" |
| |
| config SUNXI_MINIMUM_DRAM_MB |
| int "minimum DRAM size" |
| default 32 if MACH_SUNIV |
| default 64 if MACH_SUN8I_V3S |
| default 256 |
| ---help--- |
| Minimum DRAM size expected on the board. Traditionally we assumed |
| 256 MB, so that U-Boot would load at 160MB. With co-packaged DRAM |
| we have smaller sizes, though, so that U-Boot's own load address and |
| the default payload addresses must be shifted down. |
| This is expected to be fixed by the SoC selection. |
| |
| config UART0_PORT_F |
| bool "UART0 on MicroSD breakout board" |
| ---help--- |
| Repurpose the SD card slot for getting access to the UART0 serial |
| console. Primarily useful only for low level u-boot debugging on |
| tablets, where normal UART0 is difficult to access and requires |
| device disassembly and/or soldering. As the SD card can't be used |
| at the same time, the system can be only booted in the FEL mode. |
| Only enable this if you really know what you are doing. |
| |
| config OLD_SUNXI_KERNEL_COMPAT |
| bool "Enable workarounds for booting old kernels" |
| ---help--- |
| Set this to enable various workarounds for old kernels, this results in |
| sub-optimal settings for newer kernels, only enable if needed. |
| |
| config MACPWR |
| string "MAC power pin" |
| default "" |
| help |
| Set the pin used to power the MAC. This takes a string in the format |
| understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config MMC1_PINS_PH |
| bool "Pins for mmc1 are on Port H" |
| depends on MACH_SUN4I || MACH_SUN7I || MACH_SUN8I_R40 |
| ---help--- |
| Select this option for boards where mmc1 uses the Port H pinmux. |
| |
| config MMC_SUNXI_SLOT_EXTRA |
| int "mmc extra slot number" |
| default -1 |
| ---help--- |
| sunxi builds always enable mmc0, some boards also have a second sdcard |
| slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable |
| support for this. |
| |
| config USB0_VBUS_PIN |
| string "Vbus enable pin for usb0 (otg)" |
| default "" |
| ---help--- |
| Set the Vbus enable pin for usb0 (otg). This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config USB0_VBUS_DET |
| string "Vbus detect pin for usb0 (otg)" |
| default "" |
| ---help--- |
| Set the Vbus detect pin for usb0 (otg). This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config USB0_ID_DET |
| string "ID detect pin for usb0 (otg)" |
| default "" |
| ---help--- |
| Set the ID detect pin for usb0 (otg). This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config USB1_VBUS_PIN |
| string "Vbus enable pin for usb1 (ehci0)" |
| default "PH6" if MACH_SUN4I || MACH_SUN7I |
| default "PH27" if MACH_SUN6I |
| ---help--- |
| Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes |
| a string in the format understood by sunxi_name_to_gpio, e.g. |
| PH1 for pin 1 of port H. |
| |
| config USB2_VBUS_PIN |
| string "Vbus enable pin for usb2 (ehci1)" |
| default "PH3" if MACH_SUN4I || MACH_SUN7I |
| default "PH24" if MACH_SUN6I |
| ---help--- |
| See USB1_VBUS_PIN help text. |
| |
| config USB3_VBUS_PIN |
| string "Vbus enable pin for usb3 (ehci2)" |
| default "" |
| ---help--- |
| See USB1_VBUS_PIN help text. |
| |
| config I2C0_ENABLE |
| bool "Enable I2C/TWI controller 0" |
| default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40 |
| default n if MACH_SUN6I || MACH_SUN8I |
| select CMD_I2C |
| ---help--- |
| This allows enabling I2C/TWI controller 0 by muxing its pins, enabling |
| its clock and setting up the bus. This is especially useful on devices |
| with slaves connected to the bus or with pins exposed through e.g. an |
| expansion port/header. |
| |
| config I2C1_ENABLE |
| bool "Enable I2C/TWI controller 1" |
| select CMD_I2C |
| ---help--- |
| See I2C0_ENABLE help text. |
| |
| if SUNXI_GEN_SUN6I || SUN50I_GEN_H6 |
| config R_I2C_ENABLE |
| bool "Enable the PRCM I2C/TWI controller" |
| # This is used for the pmic on H3 |
| default y if SY8106A_POWER |
| select CMD_I2C |
| ---help--- |
| Set this to y to enable the I2C controller which is part of the PRCM. |
| endif |
| |
| config AXP_GPIO |
| bool "Enable support for gpio-s on axp PMICs" |
| depends on AXP_PMIC_BUS |
| ---help--- |
| Say Y here to enable support for the gpio pins of the axp PMIC ICs. |
| |
| config AXP_DISABLE_BOOT_ON_POWERON |
| bool "Disable device boot on power plug-in" |
| depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default n |
| ---help--- |
| Say Y here to prevent the device from booting up because of a plug-in |
| event. When set, the device will boot into the SPL briefly to |
| determine why it was powered on, and if it was determined because of |
| a plug-in event instead of a button press event it will shut back off. |
| |
| config VIDEO_SUNXI |
| bool "Enable graphical uboot console on HDMI, LCD or VGA" |
| depends on !MACH_SUN8I_A83T |
| depends on !MACH_SUNXI_H3_H5 |
| depends on !MACH_SUN8I_R40 |
| depends on !MACH_SUN8I_V3S |
| depends on !MACH_SUN9I |
| depends on !MACH_SUN50I |
| depends on !SUN50I_GEN_H6 |
| select VIDEO |
| select DISPLAY |
| imply VIDEO_DT_SIMPLEFB |
| default y |
| ---help--- |
| Say Y here to add support for using a graphical console on the HDMI, |
| LCD or VGA output found on older sunxi devices. This will also provide |
| a simple_framebuffer device for Linux. |
| |
| config VIDEO_HDMI |
| bool "HDMI output support" |
| depends on VIDEO_SUNXI && !MACH_SUN8I && !MACH_SUNIV |
| default y |
| ---help--- |
| Say Y here to add support for outputting video over HDMI. |
| |
| config VIDEO_VGA |
| bool "VGA output support" |
| depends on VIDEO_SUNXI && (MACH_SUN4I || MACH_SUN7I) |
| ---help--- |
| Say Y here to add support for outputting video over VGA. |
| |
| config VIDEO_VGA_VIA_LCD |
| bool "VGA via LCD controller support" |
| depends on VIDEO_SUNXI && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I) |
| ---help--- |
| Say Y here to add support for external DACs connected to the parallel |
| LCD interface driving a VGA connector, such as found on the |
| Olimex A13 boards. |
| |
| config VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH |
| bool "Force sync active high for VGA via LCD controller support" |
| depends on VIDEO_VGA_VIA_LCD |
| ---help--- |
| Say Y here if you've a board which uses opendrain drivers for the vga |
| hsync and vsync signals. Opendrain drivers cannot generate steep enough |
| positive edges for a stable video output, so on boards with opendrain |
| drivers the sync signals must always be active high. |
| |
| config VIDEO_VGA_EXTERNAL_DAC_EN |
| string "LCD panel power enable pin" |
| depends on VIDEO_VGA_VIA_LCD |
| default "" |
| ---help--- |
| Set the enable pin for the external VGA DAC. This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config VIDEO_COMPOSITE |
| bool "Composite video output support" |
| depends on VIDEO_SUNXI && (MACH_SUN4I || MACH_SUN5I || MACH_SUN7I) |
| ---help--- |
| Say Y here to add support for outputting composite video. |
| |
| config VIDEO_LCD_MODE |
| string "LCD panel timing details" |
| depends on VIDEO_SUNXI |
| default "" |
| ---help--- |
| LCD panel timing details string, leave empty if there is no LCD panel. |
| This is in drivers/video/videomodes.c: video_get_params() format, e.g. |
| x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0 |
| Also see: http://linux-sunxi.org/LCD |
| |
| config VIDEO_LCD_DCLK_PHASE |
| int "LCD panel display clock phase" |
| depends on VIDEO_SUNXI || VIDEO |
| default 1 |
| range 0 3 |
| ---help--- |
| Select LCD panel display clock phase shift |
| |
| config VIDEO_LCD_POWER |
| string "LCD panel power enable pin" |
| depends on VIDEO_SUNXI |
| default "" |
| ---help--- |
| Set the power enable pin for the LCD panel. This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config VIDEO_LCD_RESET |
| string "LCD panel reset pin" |
| depends on VIDEO_SUNXI |
| default "" |
| ---help--- |
| Set the reset pin for the LCD panel. This takes a string in the format |
| understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config VIDEO_LCD_BL_EN |
| string "LCD panel backlight enable pin" |
| depends on VIDEO_SUNXI |
| default "" |
| ---help--- |
| Set the backlight enable pin for the LCD panel. This takes a string in the |
| the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of |
| port H. |
| |
| config VIDEO_LCD_BL_PWM |
| string "LCD panel backlight pwm pin" |
| depends on VIDEO_SUNXI |
| default "" |
| ---help--- |
| Set the backlight pwm pin for the LCD panel. This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config VIDEO_LCD_BL_PWM_ACTIVE_LOW |
| bool "LCD panel backlight pwm is inverted" |
| depends on VIDEO_SUNXI |
| default y |
| ---help--- |
| Set this if the backlight pwm output is active low. |
| |
| config VIDEO_LCD_PANEL_I2C |
| bool "LCD panel needs to be configured via i2c" |
| depends on VIDEO_SUNXI |
| select DM_I2C_GPIO |
| ---help--- |
| Say y here if the LCD panel needs to be configured via i2c. This |
| will add a bitbang i2c controller using gpios to talk to the LCD. |
| |
| config VIDEO_LCD_PANEL_I2C_NAME |
| string "LCD panel i2c interface node name" |
| depends on VIDEO_LCD_PANEL_I2C |
| default "i2c" |
| ---help--- |
| Set the device tree node name for the LCD i2c interface. |
| |
| # Note only one of these may be selected at a time! But hidden choices are |
| # not supported by Kconfig |
| config VIDEO_LCD_IF_PARALLEL |
| bool |
| |
| config VIDEO_LCD_IF_LVDS |
| bool |
| |
| config SUNXI_DE2 |
| bool |
| |
| config VIDEO_DE2 |
| bool "Display Engine 2 video driver" |
| depends on SUNXI_DE2 |
| select VIDEO |
| select DISPLAY |
| select VIDEO_DW_HDMI |
| imply VIDEO_DT_SIMPLEFB |
| default y |
| ---help--- |
| Say y here if you want to build DE2 video driver which is present on |
| newer SoCs. Currently only HDMI output is supported. |
| |
| |
| choice |
| prompt "LCD panel support" |
| depends on VIDEO_SUNXI |
| ---help--- |
| Select which type of LCD panel to support. |
| |
| config VIDEO_LCD_PANEL_PARALLEL |
| bool "Generic parallel interface LCD panel" |
| select VIDEO_LCD_IF_PARALLEL |
| |
| config VIDEO_LCD_PANEL_LVDS |
| bool "Generic lvds interface LCD panel" |
| select VIDEO_LCD_IF_LVDS |
| |
| config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828 |
| bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip" |
| select VIDEO_LCD_SSD2828 |
| select VIDEO_LCD_IF_PARALLEL |
| ---help--- |
| 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0 |
| |
| config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804 |
| bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip" |
| select VIDEO_LCD_ANX9804 |
| select VIDEO_LCD_IF_PARALLEL |
| select VIDEO_LCD_PANEL_I2C |
| ---help--- |
| Select this for eDP LCD panels with 4 lanes running at 1.62G, |
| connected via an ANX9804 bridge chip. |
| |
| config VIDEO_LCD_PANEL_HITACHI_TX18D42VM |
| bool "Hitachi tx18d42vm LCD panel" |
| select VIDEO_LCD_HITACHI_TX18D42VM |
| select VIDEO_LCD_IF_LVDS |
| ---help--- |
| 7.85" 1024x768 Hitachi tx18d42vm LCD panel support |
| |
| config VIDEO_LCD_TL059WV5C0 |
| bool "tl059wv5c0 LCD panel" |
| select VIDEO_LCD_PANEL_I2C |
| select VIDEO_LCD_IF_PARALLEL |
| ---help--- |
| 6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and |
| Aigo M60/M608/M606 tablets. |
| |
| endchoice |
| |
| config SATAPWR |
| string "SATA power pin" |
| default "" |
| help |
| Set the pins used to power the SATA. This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of |
| port H. |
| |
| config GMAC_TX_DELAY |
| int "GMAC Transmit Clock Delay Chain" |
| default 0 |
| ---help--- |
| Set the GMAC Transmit Clock Delay Chain value. |
| |
| config SPL_STACK_R_ADDR |
| default 0x81e00000 if MACH_SUNIV |
| default 0x4fe00000 if MACH_SUN4I |
| default 0x4fe00000 if MACH_SUN5I |
| default 0x4fe00000 if MACH_SUN6I |
| default 0x4fe00000 if MACH_SUN7I |
| default 0x4fe00000 if MACH_SUN8I |
| default 0x2fe00000 if MACH_SUN9I |
| default 0x4fe00000 if MACH_SUN50I |
| default 0x4fe00000 if SUN50I_GEN_H6 |
| |
| config SPL_SPI_SUNXI |
| bool "Support for SPI Flash on Allwinner SoCs in SPL" |
| depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_R40 || SUN50I_GEN_H6 || MACH_SUNIV |
| help |
| Enable support for SPI Flash. This option allows SPL to read from |
| sunxi SPI Flash. It uses the same method as the boot ROM, so does |
| not need any extra configuration. |
| |
| config PINE64_DT_SELECTION |
| bool "Enable Pine64 device tree selection code" |
| depends on MACH_SUN50I |
| help |
| The original Pine A64 and Pine A64+ are similar but different |
| boards and can be differed by the DRAM size. Pine A64 has |
| 512MiB DRAM, and Pine A64+ has 1GiB or 2GiB. By selecting this |
| option, the device tree selection code specific to Pine64 which |
| utilizes the DRAM size will be enabled. |
| |
| config PINEPHONE_DT_SELECTION |
| bool "Enable PinePhone device tree selection code" |
| depends on MACH_SUN50I |
| help |
| Enable this option to automatically select the device tree for the |
| correct PinePhone hardware revision during boot. |
| |
| config BLUETOOTH_DT_DEVICE_FIXUP |
| string "Fixup the Bluetooth controller address" |
| default "" |
| help |
| This option specifies the DT compatible name of the Bluetooth |
| controller for which to set the "local-bd-address" property. |
| Set this option if your device ships with the Bluetooth controller |
| default address. |
| The used address is "bdaddr" if set, and "ethaddr" with the LSB |
| flipped elsewise. |
| |
| source "board/sunxi/Kconfig" |
| |
| endif |
| |
| config CHIP_DIP_SCAN |
| bool "Enable DIPs detection for CHIP board" |
| select SUPPORT_EXTENSION_SCAN |
| select W1 |
| select W1_GPIO |
| select W1_EEPROM |
| select W1_EEPROM_DS24XXX |
| select CMD_EXTENSION |