armv8/ls1043ardb: Add LS1043ARDB board support

LS1043ARDB Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 SDRAM (32bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * XFI 10G port
 * QSGMII with 4x 1G ports
 * Two RGMII ports

PCIe:
 * PCIe2 (Lanes C) to mini-PCIe slot
 * PCIe3 (Lanes D) to PCIe slot

USB 3.0: two super speed USB 3.0 type A ports

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
diff --git a/board/freescale/ls1043ardb/ddr.c b/board/freescale/ls1043ardb/ddr.c
new file mode 100644
index 0000000..b181579
--- /dev/null
+++ b/board/freescale/ls1043ardb/ddr.c
@@ -0,0 +1,191 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include "ddr.h"
+#ifdef CONFIG_FSL_DEEP_SLEEP
+#include <fsl_sleep.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			   dimm_params_t *pdimm,
+			   unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 1) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	pbsp = udimms[0];
+
+	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				popts->cpo_override = pbsp->cpo_override;
+				popts->write_data_delay =
+					pbsp->write_data_delay;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found for %lu MT/s\n",
+		       ddr_freq);
+		printf("Trying to use the highest speed (%u) parameters\n",
+		       pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+	      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+
+	/* force DDR bus width to 32 bits */
+	popts->data_bus_width = 1;
+	popts->otf_burst_chop_en = 0;
+	popts->burst_length = DDR_BL8;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 1;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
+}
+
+/* DDR model number: MT40A512M8HX-093E */
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+dimm_params_t ddr_raw_timing = {
+	.n_ranks = 1,
+	.rank_density = 2147483648u,
+	.capacity = 2147483648u,
+	.primary_sdram_width = 32,
+	.ec_sdram_width = 0,
+	.registered_dimm = 0,
+	.mirrored_dimm = 0,
+	.n_row_addr = 15,
+	.n_col_addr = 10,
+	.bank_addr_bits = 0,
+	.bank_group_bits = 2,
+	.edc_config = 0,
+	.burst_lengths_bitmask = 0x0c,
+
+	.tckmin_x_ps = 938,
+	.tckmax_ps = 1500,
+	.caslat_x = 0x000DFA00,
+	.taa_ps = 13500,
+	.trcd_ps = 13500,
+	.trp_ps = 13500,
+	.tras_ps = 33000,
+	.trc_ps = 46500,
+	.trfc1_ps = 260000,
+	.trfc2_ps = 160000,
+	.trfc4_ps = 110000,
+	.tfaw_ps = 21000,
+	.trrds_ps = 3700,
+	.trrdl_ps = 5300,
+	.tccdl_ps = 5355,
+	.refresh_rate_ps = 7800000,
+	.dq_mapping[0] = 0x0,
+	.dq_mapping[1] = 0x0,
+	.dq_mapping[2] = 0x0,
+	.dq_mapping[3] = 0x0,
+	.dq_mapping[4] = 0x0,
+	.dq_mapping[5] = 0x0,
+	.dq_mapping[6] = 0x0,
+	.dq_mapping[7] = 0x0,
+	.dq_mapping[8] = 0x0,
+	.dq_mapping[9] = 0x0,
+	.dq_mapping[10] = 0x0,
+	.dq_mapping[11] = 0x0,
+	.dq_mapping[12] = 0x0,
+	.dq_mapping[13] = 0x0,
+	.dq_mapping[14] = 0x0,
+	.dq_mapping[15] = 0x0,
+	.dq_mapping[16] = 0x0,
+	.dq_mapping[17] = 0x0,
+	.dq_mapping_ors = 0,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+			    unsigned int controller_number,
+			    unsigned int dimm_number)
+{
+	static const char dimm_model[] = "Fixed DDR on board";
+
+	if (((controller_number == 0) && (dimm_number == 0)) ||
+	    ((controller_number == 1) && (dimm_number == 0))) {
+		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+	}
+
+	return 0;
+}
+#endif
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
+	puts("Initializing DDR....\n");
+	dram_size = fsl_ddr_sdram();
+#else
+	dram_size =  fsl_ddr_sdram_size();
+#endif
+#ifdef CONFIG_FSL_DEEP_SLEEP
+	fsl_dp_ddr_restore();
+#endif
+
+	return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}