armv8/ls1043ardb: Add LS1043ARDB board support
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
new file mode 100644
index 0000000..f866bed
--- /dev/null
+++ b/include/configs/ls1043a_common.h
@@ -0,0 +1,172 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1043A_COMMON_H
+#define __LS1043A_COMMON_H
+
+#define CONFIG_REMAKE_ELF
+#define CONFIG_FSL_LAYERSCAPE
+#define CONFIG_FSL_LSCH2
+#define CONFIG_LS1043A
+#define CONFIG_SYS_FSL_CLK
+#define CONFIG_GICV2
+
+#include <asm/arch/config.h>
+#ifdef CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_HAS_SERDES
+#endif
+
+/* Link Definitions */
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+#ifndef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
+#endif
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 25000000 /* 25MHz */
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/* IFC */
+#define CONFIG_FSL_IFC
+/*
+ * CONFIG_SYS_FLASH_BASE has the final address (core view)
+ * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
+ */
+#define CONFIG_SYS_FLASH_BASE 0x60000000
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+#endif
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_I2C_MXC_I2C4
+
+/* PCIe */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE2 /* PCIE controller 2 */
+#define CONFIG_PCIE3 /* PCIE controller 3 */
+#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
+#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS 0x40000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000
+#define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */
+
+#ifdef CONFIG_PCI
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP
+#define CONFIG_E1000
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI
+#endif
+
+/* Command line configuration */
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_PING
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_HWCONFIG
+#define HWCONFIG_BUFFER_SIZE 128
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x80100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x61200000\0" \
+ "kernel_load=0x807f0000\0" \
+ "kernel_size=0x1000000\0" \
+ "console=ttyAMA0,38400n8\0"
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
+ "earlycon=uart8250,0x21c0500,115200"
+#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
+ "$kernel_size && bootm $kernel_load"
+#define CONFIG_BOOTDELAY 10
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_MAXARGS 64 /* max command args */
+
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#endif /* __LS1043A_COMMON_H */
diff --git a/include/configs/ls1043ardb.h b/include/configs/ls1043ardb.h
new file mode 100644
index 0000000..1f66201
--- /dev/null
+++ b/include/configs/ls1043ardb.h
@@ -0,0 +1,191 @@
+/*
+ * Copyright 2015 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1043ARDB_H__
+#define __LS1043ARDB_H__
+
+#include "ls1043a_common.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_SYS_TEXT_BASE 0x60100000
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+/* Physical Memory Map */
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#define CONFIG_NR_DRAM_BANKS 1
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+
+#define CONFIG_FSL_DDR_BIST
+#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+
+/*
+ * NOR Flash Definitions
+ */
+#define CONFIG_SYS_NOR_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+#define CONFIG_SYS_NOR_CSPR \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+ CSOR_NOR_TRHZ_80)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \
+ FTIM0_NOR_TEADC(0x1) | \
+ FTIM0_NOR_TAVDS(0x0) | \
+ FTIM0_NOR_TEAHC(0xc))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1c) | \
+ FTIM1_NOR_TRAD_NOR(0xb) | \
+ FTIM1_NOR_TSEQRAD_NOR(0x9))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x1) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x8) | \
+ FTIM2_NOR_TWP(0x10))
+#define CONFIG_SYS_NOR_FTIM3 0
+#define CONFIG_SYS_IFC_CCR 0x01000000
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS }
+
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
+/*
+ * NAND Flash Definitions
+ */
+#define CONFIG_NAND_FSL_IFC
+
+#define CONFIG_SYS_NAND_BASE 0x7e800000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_NAND \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /* 64 Pages Per Block */
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x7) | \
+ FTIM0_NAND_TWH(0xa))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0xe) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
+ FTIM2_NAND_TREH(0xa) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/*
+ * CPLD
+ */
+#define CONFIG_SYS_CPLD_BASE 0x7fb00000
+#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
+
+#define CONFIG_SYS_CPLD_CSPR_EXT (0x0)
+#define CONFIG_SYS_CPLD_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_CPLD_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_CPLD_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+ CSOR_NOR_NOR_MODE_AVD_NOR | \
+ CSOR_NOR_TRHZ_80)
+
+/* CPLD Timing parameters for IFC GPCM */
+#define CONFIG_SYS_CPLD_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \
+ FTIM0_GPCM_TEADC(0xf) | \
+ FTIM0_GPCM_TEAHC(0xf))
+#define CONFIG_SYS_CPLD_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CPLD_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
+ FTIM2_GPCM_TCH(0xf) | \
+ FTIM2_GPCM_TWP(0xff))
+#define CONFIG_SYS_CPLD_FTIM3 0x0
+
+/* IFC Timing Params */
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_CPLD_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_CPLD_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_CPLD_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_CPLD_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_CPLD_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_CPLD_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_CPLD_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_CPLD_FTIM3
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE 0x20000
+
+#endif /* __LS1043ARDB_H__ */