Stop using immap_t for guts offset on 85xx
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/cpu/mpc85xx/pci.c b/cpu/mpc85xx/pci.c
index db09e45..35e96d9 100644
--- a/cpu/mpc85xx/pci.c
+++ b/cpu/mpc85xx/pci.c
@@ -48,7 +48,7 @@
#ifdef CONFIG_MPC85XX_PCI2
volatile ccsr_pcix_t *pcix2 = &immap->im_pcix2;
#endif
- volatile ccsr_gur_t *gur = &immap->im_gur;
+ volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
struct pci_controller * hose;
pci_hose = board_hose;
diff --git a/cpu/mpc85xx/qe_io.c b/cpu/mpc85xx/qe_io.c
index 8878bc5..98075bb 100644
--- a/cpu/mpc85xx/qe_io.c
+++ b/cpu/mpc85xx/qe_io.c
@@ -34,9 +34,9 @@
u32 pin_2bit_assign;
u32 pin_1bit_mask;
u32 tmp_val;
- volatile immap_t *im = (volatile immap_t *)CFG_IMMR;
+ volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
volatile par_io_t *par_io = (volatile par_io_t *)
- &(im->im_gur.qe_par_io);
+ &(gur->qe_par_io);
/* Caculate pin location and 2bit mask and dir */
pin_2bit_mask = (u32)(0x3 << (NUM_OF_PINS-(pin%(NUM_OF_PINS/2)+1)*2));
diff --git a/cpu/mpc85xx/spd_sdram.c b/cpu/mpc85xx/spd_sdram.c
index 5dc223a..307ba3b 100644
--- a/cpu/mpc85xx/spd_sdram.c
+++ b/cpu/mpc85xx/spd_sdram.c
@@ -309,7 +309,7 @@
if ((SVR_VER(get_svr()) == SVR_8548_E) &&
(SVR_MJREV(get_svr()) == 1) &&
(spd.mem_type == SPD_MEMTYPE_DDR2)) {
- volatile ccsr_gur_t *gur = &immap->im_gur;
+ volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
gur->ddrioovcr = (0x80000000 /* Enable */
| 0x10000000);/* VSEL to 1.8V */
}
diff --git a/cpu/mpc85xx/speed.c b/cpu/mpc85xx/speed.c
index 12359a2..5c35d4a 100644
--- a/cpu/mpc85xx/speed.c
+++ b/cpu/mpc85xx/speed.c
@@ -35,8 +35,7 @@
void get_sys_info (sys_info_t * sysInfo)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- volatile ccsr_gur_t *gur = &immap->im_gur;
+ volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
uint plat_ratio,e500_ratio,half_freqSystemBus;
plat_ratio = (gur->porpllsr) & 0x0000003e;