arm nomadik: allow Nand and OneNand to coexists
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
diff --git a/Makefile b/Makefile
index 3877c97..d486b55 100644
--- a/Makefile
+++ b/Makefile
@@ -2860,9 +2860,9 @@
@ > $(obj)include/config.h
@if [ "$(findstring _onenand, $@)" ] ; then \
echo "#define CONFIG_BOOT_ONENAND" >> $(obj)include/config.h; \
- $(XECHO) "... configured for OneNand Flash"; \
+ $(XECHO) "... configured to boot from OneNand Flash"; \
else \
- $(XECHO) "... configured for Nand Flash"; \
+ $(XECHO) "... configured to boot from Nand Flash"; \
fi
@$(MKCONFIG) -a nhk8815 arm arm926ejs nhk8815 st nomadik
diff --git a/board/st/nhk8815/nhk8815.c b/board/st/nhk8815/nhk8815.c
index edf4626..085a5e0 100644
--- a/board/st/nhk8815/nhk8815.c
+++ b/board/st/nhk8815/nhk8815.c
@@ -53,6 +53,10 @@
writel(0x0000305b, REG_FSMC_BCR1);
writel(0x00033f33, REG_FSMC_BTR1);
+ /* Set up SMCS0 for OneNand: sram-like once again */
+ writel(0x000030db, NOMADIK_FSMC_BASE + 0x00); /* FSMC_BCR0 */
+ writel(0x02100551, NOMADIK_FSMC_BASE + 0x04); /* FSMC_BTR0 */
+
icache_enable();
return 0;
}
diff --git a/doc/README.nhk8815 b/doc/README.nhk8815
index 453cfae..9008e39 100644
--- a/doc/README.nhk8815
+++ b/doc/README.nhk8815
@@ -15,6 +15,16 @@
implemented in the X-Loader, so U-Boot is already running in SDRAM
when control is handed over to it.
+The Makefile offers two different configurations to be used if you
+boot from Nand or OneNand.
+
+ make nhk8815_config
+ make nhk8815_onenand_config
+
+Both support OneNand and Nand. Since U-Boot, running in RAM, can't know
+where it was loaded from, the configurations differ in where the filesystem
+is looked for by default.
+
On www.st.com/nomadik and on www.stnwireless.com there are documents,
summary data and white papers on Nomadik. The full datasheet for
diff --git a/include/configs/nhk8815.h b/include/configs/nhk8815.h
index 321adfa..bf1a915 100644
--- a/include/configs/nhk8815.h
+++ b/include/configs/nhk8815.h
@@ -55,6 +55,7 @@
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT "Nomadik> "
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
@@ -90,6 +91,7 @@
#define CONFIG_SYS_MEMTEST_END 0x0FFFFFFF
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256 * 1024)
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* for initial data */
+#define CONFIG_SYS_64BIT_VSPRINTF /* mtd desires this */
#define CONFIG_MISC_INIT_R /* call misc_init_r during start up */
@@ -120,43 +122,54 @@
#define CONFIG_SMC_USE_32_BIT
#define CONFIG_BOOTFILE "uImage"
-/* flash memory and filesystem information */
-#define CONFIG_DOS_PARTITION
+/* Storage information: onenand and nand */
+#define CONFIG_CMD_ONENAND
#define CONFIG_MTD_ONENAND_VERIFY_WRITE
#define CONFIG_SYS_ONENAND_BASE 0x30000000
+
+#define CONFIG_CMD_NAND
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000 /* SMPS0n */
+/*
+ * Filesystem information
+ *
+ * Since U-Boot has been loaded to RAM by vendor code, we could use
+ * either or both OneNand and Nand. However, we need to know where the
+ * filesystem lives. Comments below report vendor-selected partitions
+ */
#ifdef CONFIG_BOOT_ONENAND
-
-# define CONFIG_CMD_ONENAND /* Temporary: nand and onenand can't coexist */
/* Partition Size Start
* XloaderTOC + X-Loader 256KB 0x00000000
* Memory init function 256KB 0x00040000
- * U-Boot 2MB 0x00080000
+ * U-Boot + env 2MB 0x00080000
* Sysimage (kernel + ramdisk) 4MB 0x00280000
* JFFS2 Root filesystem 22MB 0x00680000
* JFFS2 User Data 227.5MB 0x01C80000
*/
-# define CONFIG_JFFS2_PART_SIZE 0x400000
-# define CONFIG_JFFS2_PART_OFFSET 0x280000
-
+# define CONFIG_JFFS2_DEV "onenand0"
+# define CONFIG_JFFS2_PART_SIZE 0x01600000
+# define CONFIG_JFFS2_PART_OFFSET 0x00680000
# define CONFIG_ENV_IS_IN_ONENAND
-# define CONFIG_ENV_SIZE (256 * 1024)
-# define CONFIG_ENV_ADDR 0x30300000
+# define CONFIG_ENV_SIZE 0x20000 /* 128 Kb - one sector */
+# define CONFIG_ENV_ADDR (0x00280000 - CONFIG_ENV_SIZE)
-#else /* ! CONFIG_BOOT_ONENAND */
-
-# define CONFIG_CMD_NAND /* Temporary: nand and onenand can't coexist */
-
+#else /* BOOT_NAND */
+ /* Partition Size Start
+ * XloaderTOC + X-Loader 256KB 0x00000000
+ * Memory init function 256KB 0x00040000
+ * U-Boot + env 2MB 0x00080000
+ * Kernel Image 3MB 0x00280000
+ * JFFS2 Root filesystem 22MB 0x00580000
+ * JFFS2 User Data 100.5MB 0x01b80000
+ */
# define CONFIG_JFFS2_DEV "nand0"
# define CONFIG_JFFS2_NAND 1 /* For the jffs2 support*/
-# define CONFIG_JFFS2_PART_SIZE 0x00300000
-# define CONFIG_JFFS2_PART_OFFSET 0x00280000
-
+# define CONFIG_JFFS2_PART_SIZE 0x01600000
+# define CONFIG_JFFS2_PART_OFFSET 0x00580000
# define CONFIG_ENV_IS_IN_NAND
# define CONFIG_ENV_SIZE 0x20000 /* 128 Kb - one sector */
-# define CONFIG_ENV_OFFSET (0x8000000 - CONFIG_ENV_SIZE)
+# define CONFIG_ENV_OFFSET (0x00280000 - CONFIG_ENV_SIZE)
#endif /* CONFIG_BOOT_ONENAND */