85xx: Add RMII support for MPC8569MDS
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is more accurate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c
index 387ecad..1e7526a 100644
--- a/board/freescale/mpc8569mds/mpc8569mds.c
+++ b/board/freescale/mpc8569mds/mpc8569mds.c
@@ -47,6 +47,7 @@
/* QE_MUX_MDIO */
{2, 30, 3, 0, 2}, /* QE_MUX_MDIO */
+#if defined(CONFIG_SYS_UCC_RGMII_MODE)
/* UCC_1_RGMII */
{2, 11, 2, 0, 1}, /* CLK12 */
{0, 0, 1, 0, 3}, /* ENET1_TXD0_SER1_TXD0 */
@@ -107,6 +108,44 @@
{2, 17, 2, 0, 2}, /* ENET4_GRXCLK */
{2, 24, 1, 0, 2}, /* ENET4_GTXCLK */
+#elif defined(CONFIG_SYS_UCC_RMII_MODE)
+ /* UCC_1_RMII */
+ {2, 15, 2, 0, 1}, /* CLK16 */
+ {0, 0, 1, 0, 3}, /* ENET1_TXD0_SER1_TXD0 */
+ {0, 1, 1, 0, 3}, /* ENET1_TXD1_SER1_TXD1 */
+ {0, 6, 2, 0, 3}, /* ENET1_RXD0_SER1_RXD0 */
+ {0, 7, 2, 0, 1}, /* ENET1_RXD1_SER1_RXD1 */
+ {0, 4, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */
+ {0, 12, 2, 0, 3}, /* ENET1_RX_DV_SER1_CTS_B */
+
+ /* UCC_2_RMII */
+ {2, 15, 2, 0, 1}, /* CLK16 */
+ {0, 14, 1, 0, 2}, /* ENET2_TXD0_SER2_TXD0 */
+ {0, 15, 1, 0, 2}, /* ENET2_TXD1_SER2_TXD1 */
+ {0, 20, 2, 0, 2}, /* ENET2_RXD0_SER2_RXD0 */
+ {0, 21, 2, 0, 1}, /* ENET2_RXD1_SER2_RXD1 */
+ {0, 18, 1, 0, 2}, /* ENET2_TX_EN_SER2_RTS_B */
+ {0, 26, 2, 0, 3}, /* ENET2_RX_DV_SER2_CTS_B */
+
+ /* UCC_3_RMII */
+ {2, 15, 2, 0, 1}, /* CLK16 */
+ {0, 29, 1, 0, 2}, /* ENET3_TXD0_SER3_TXD0 */
+ {0, 30, 1, 0, 3}, /* ENET3_TXD1_SER3_TXD1 */
+ {1, 3, 2, 0, 3}, /* ENET3_RXD0_SER3_RXD0 */
+ {1, 4, 2, 0, 1}, /* ENET3_RXD1_SER3_RXD1 */
+ {1, 1, 1, 0, 1}, /* ENET3_TX_EN_SER3_RTS_B */
+ {1, 9, 2, 0, 3}, /* ENET3_RX_DV_SER3_CTS_B */
+
+ /* UCC_4_RMII */
+ {2, 15, 2, 0, 1}, /* CLK16 */
+ {1, 12, 1, 0, 2}, /* ENET4_TXD0_SER4_TXD0 */
+ {1, 13, 1, 0, 2}, /* ENET4_TXD1_SER4_TXD1 */
+ {1, 18, 2, 0, 2}, /* ENET4_RXD0_SER4_RXD0 */
+ {1, 19, 2, 0, 1}, /* ENET4_RXD1_SER4_RXD1 */
+ {1, 16, 1, 0, 2}, /* ENET4_TX_EN_SER4_RTS_B */
+ {1, 24, 2, 0, 3}, /* ENET4_RX_DV_SER4_CTS_B */
+#endif
+
/* UART1 is muxed with QE PortF bit [9-12].*/
{5, 12, 2, 0, 3}, /* UART1_SIN */
{5, 9, 1, 0, 3}, /* UART1_SOUT */
@@ -128,7 +167,7 @@
enable_8569mds_flash_write();
#ifdef CONFIG_QE
- enable_8569mds_qe_mdio();
+ enable_8569mds_qe_uec();
#endif
#if CONFIG_SYS_I2C2_OFFSET
@@ -350,6 +389,61 @@
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
+#if defined(CONFIG_SYS_UCC_RMII_MODE)
+ int nodeoff, off, err;
+ unsigned int val;
+ const u32 *ph;
+ const u32 *index;
+
+ /* fixup device tree for supporting rmii mode */
+ nodeoff = -1;
+ while ((nodeoff = fdt_node_offset_by_compatible(blob, nodeoff,
+ "ucc_geth")) >= 0) {
+ err = fdt_setprop_string(blob, nodeoff, "tx-clock-name",
+ "clk16");
+ if (err < 0) {
+ printf("WARNING: could not set tx-clock-name %s.\n",
+ fdt_strerror(err));
+ break;
+ }
+
+ err = fdt_setprop_string(blob, nodeoff, "phy-connection-type",
+ "rmii");
+ if (err < 0) {
+ printf("WARNING: could not set phy-connection-type "
+ "%s.\n", fdt_strerror(err));
+ break;
+ }
+
+ index = fdt_getprop(blob, nodeoff, "cell-index", 0);
+ if (index == NULL) {
+ printf("WARNING: could not get cell-index of ucc\n");
+ break;
+ }
+
+ ph = fdt_getprop(blob, nodeoff, "phy-handle", 0);
+ if (ph == NULL) {
+ printf("WARNING: could not get phy-handle of ucc\n");
+ break;
+ }
+
+ off = fdt_node_offset_by_phandle(blob, *ph);
+ if (off < 0) {
+ printf("WARNING: could not get phy node %s.\n",
+ fdt_strerror(err));
+ break;
+ }
+
+ val = 0x7 + *index; /* RMII phy address starts from 0x8 */
+
+ err = fdt_setprop(blob, off, "reg", &val, sizeof(u32));
+ if (err < 0) {
+ printf("WARNING: could not set reg for phy-handle "
+ "%s.\n", fdt_strerror(err));
+ break;
+ }
+ }
+#endif
ft_cpu_setup(blob, bd);
#ifdef CONFIG_PCIE1