arm: ti: k3: Resync dts files and bindings with Linux Kernel v5.14
This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release. Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.
Tested on j721e_evm and am65x_evm.
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/dts/k3-am642-sk.dts b/arch/arm/dts/k3-am642-sk.dts
index df76c6e..d3aa290 100644
--- a/arch/arm/dts/k3-am642-sk.dts
+++ b/arch/arm/dts/k3-am642-sk.dts
@@ -5,6 +5,8 @@
/dts-v1/;
+#include <dt-bindings/mux/ti-serdes.h>
+#include <dt-bindings/phy/phy.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/net/ti-dp83867.h>
#include "k3-am642.dtsi"
@@ -35,6 +37,93 @@
alignment = <0x1000>;
no-map;
};
+
+ main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa0000000 0x00 0x100000>;
+ no-map;
+ };
+
+ main_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa0100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa1000000 0x00 0x100000>;
+ no-map;
+ };
+
+ main_r5fss0_core1_memory_region: r5f-memory@a1100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa1100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a2000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa2000000 0x00 0x100000>;
+ no-map;
+ };
+
+ main_r5fss1_core0_memory_region: r5f-memory@a2100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa2100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a3000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa3000000 0x00 0x100000>;
+ no-map;
+ };
+
+ main_r5fss1_core1_memory_region: r5f-memory@a3100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa3100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ rtos_ipc_memory_region: ipc-memories@a5000000 {
+ reg = <0x00 0xa5000000 0x00 0x00800000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+ };
+
+ vusb_main: fixed-regulator-vusb-main5v0 {
+ /* USB MAIN INPUT 5V DC */
+ compatible = "regulator-fixed";
+ regulator-name = "vusb_main5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_3v3_sys: fixedregulator-vcc-3v3-sys {
+ /* output of LP8733xx */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_sys";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vusb_main>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: fixed-regulator-sd {
+ /* TPS2051BD */
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vcc_3v3_sys>;
+ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
};
};
@@ -52,6 +141,12 @@
>;
};
+ main_usb0_pins_default: main-usb0-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
@@ -99,6 +194,30 @@
AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
>;
};
+
+ ospi0_pins_default: ospi0-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */
+ AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */
+ AM64X_IOPAD(0x000c, PIN_INPUT, 0) /* (M19) OSPI0_D0 */
+ AM64X_IOPAD(0x0010, PIN_INPUT, 0) /* (M18) OSPI0_D1 */
+ AM64X_IOPAD(0x0014, PIN_INPUT, 0) /* (M20) OSPI0_D2 */
+ AM64X_IOPAD(0x0018, PIN_INPUT, 0) /* (M21) OSPI0_D3 */
+ AM64X_IOPAD(0x001c, PIN_INPUT, 0) /* (P21) OSPI0_D4 */
+ AM64X_IOPAD(0x0020, PIN_INPUT, 0) /* (P20) OSPI0_D5 */
+ AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* (N18) OSPI0_D6 */
+ AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */
+ AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */
+ >;
+ };
+};
+
+&mcu_uart0 {
+ status = "disabled";
+};
+
+&mcu_uart1 {
+ status = "disabled";
};
&main_uart1 {
@@ -126,8 +245,51 @@
status = "disabled";
};
+&mcu_i2c0 {
+ status = "disabled";
+};
+
+&mcu_i2c1 {
+ status = "disabled";
+};
+
+&main_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+
+ exp1: gpio@70 {
+ compatible = "nxp,pca9538";
+ reg = <0x70>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+ "PRU_DETECT", "MMC1_SD_EN",
+ "VPP_LDO_EN", "RPI_PS_3V3_En",
+ "RPI_PS_5V0_En", "RPI_HAT_DETECT";
+ };
+};
+
+&main_i2c3 {
+ status = "disabled";
+};
+
+&mcu_spi0 {
+ status = "disabled";
+};
+
+&mcu_spi1 {
+ status = "disabled";
+};
+
+/* mcu_gpio0 is reserved for mcu firmware usage */
+&mcu_gpio0 {
+ status = "reserved";
+};
+
&sdhci1 {
/* SD/MMC */
+ vmmc-supply = <&vdd_mmc1>;
pinctrl-names = "default";
bus-width = <4>;
pinctrl-0 = <&main_mmc1_pins_default>;
@@ -135,6 +297,33 @@
disable-wp;
};
+&serdes_ln_ctrl {
+ idle-states = <AM64_SERDES0_LANE0_USB>;
+};
+
+&serdes0 {
+ serdes0_usb_link: phy@0 {
+ reg = <0>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_USB3>;
+ resets = <&serdes_wiz0 1>;
+ };
+};
+
+&usbss0 {
+ ti,vbus-divider;
+};
+
+&usb0 {
+ dr_mode = "host";
+ maximum-speed = "super-speed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_usb0_pins_default>;
+ phys = <&serdes0_usb_link>;
+ phy-names = "cdns3,usb3-phy";
+};
+
&cpsw3g {
pinctrl-names = "default";
pinctrl-0 = <&mdio1_pins_default
@@ -147,10 +336,120 @@
phy-handle = <&cpsw3g_phy0>;
};
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy1>;
+};
+
&cpsw3g_mdio {
cpsw3g_phy0: ethernet-phy@0 {
reg = <0>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
};
+
+ cpsw3g_phy1: ethernet-phy@1 {
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+};
+
+&tscadc0 {
+ status = "disabled";
+};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ospi0_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&mailbox0_cluster2 {
+ mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
+ ti,mbox-rx = <0 0 2>;
+ ti,mbox-tx = <1 0 2>;
+ };
+
+ mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
+ ti,mbox-rx = <2 0 2>;
+ ti,mbox-tx = <3 0 2>;
+ };
+};
+
+&mailbox0_cluster3 {
+ status = "disabled";
+};
+
+&mailbox0_cluster4 {
+ mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 {
+ ti,mbox-rx = <0 0 2>;
+ ti,mbox-tx = <1 0 2>;
+ };
+
+ mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 {
+ ti,mbox-rx = <2 0 2>;
+ ti,mbox-tx = <3 0 2>;
+ };
+};
+
+&mailbox0_cluster5 {
+ status = "disabled";
+};
+
+&mailbox0_cluster6 {
+ mbox_m4_0: mbox-m4-0 {
+ ti,mbox-rx = <0 0 2>;
+ ti,mbox-tx = <1 0 2>;
+ };
+};
+
+&mailbox0_cluster7 {
+ status = "disabled";
+};
+
+&main_r5fss0_core0 {
+ mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>;
+ memory-region = <&main_r5fss0_core0_dma_memory_region>,
+ <&main_r5fss0_core0_memory_region>;
+};
+
+&main_r5fss0_core1 {
+ mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>;
+ memory-region = <&main_r5fss0_core1_dma_memory_region>,
+ <&main_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss1_core0 {
+ mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>;
+ memory-region = <&main_r5fss1_core0_dma_memory_region>,
+ <&main_r5fss1_core0_memory_region>;
+};
+
+&main_r5fss1_core1 {
+ mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>;
+ memory-region = <&main_r5fss1_core1_dma_memory_region>,
+ <&main_r5fss1_core1_memory_region>;
+};
+
+&pcie0_rc {
+ status = "disabled";
+};
+
+&pcie0_ep {
+ status = "disabled";
};