board: sama5d3xek: Convert to CONFIG_DM_VIDEO
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
diff --git a/board/atmel/sama5d3xek/sama5d3xek.c b/board/atmel/sama5d3xek/sama5d3xek.c
index 6d473fc..98d846f 100644
--- a/board/atmel/sama5d3xek/sama5d3xek.c
+++ b/board/atmel/sama5d3xek/sama5d3xek.c
@@ -13,9 +13,7 @@
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <debug_uart.h>
-#include <lcd.h>
#include <linux/ctype.h>
-#include <atmel_hlcdc.h>
#include <phy.h>
#include <micrel.h>
#include <spl.h>
@@ -132,80 +130,6 @@
}
#endif
-#ifdef CONFIG_LCD
-vidinfo_t panel_info = {
- .vl_col = 800,
- .vl_row = 480,
- .vl_clk = 24000000,
- .vl_bpix = LCD_BPP,
- .vl_tft = 1,
- .vl_hsync_len = 128,
- .vl_left_margin = 64,
- .vl_right_margin = 64,
- .vl_vsync_len = 2,
- .vl_upper_margin = 22,
- .vl_lower_margin = 21,
- .mmio = ATMEL_BASE_LCDC,
-};
-
-void lcd_enable(void)
-{
-}
-
-void lcd_disable(void)
-{
-}
-
-static void sama5d3xek_lcd_hw_init(void)
-{
- gd->fb_base = CONFIG_SAMA5D3_LCD_BASE;
-
- /* The higher 8 bit of LCD is board related */
- at91_pio3_set_c_periph(AT91_PIO_PORTC, 14, 0); /* LCDD16 */
- at91_pio3_set_c_periph(AT91_PIO_PORTC, 13, 0); /* LCDD17 */
- at91_pio3_set_c_periph(AT91_PIO_PORTC, 12, 0); /* LCDD18 */
- at91_pio3_set_c_periph(AT91_PIO_PORTC, 11, 0); /* LCDD19 */
- at91_pio3_set_c_periph(AT91_PIO_PORTC, 10, 0); /* LCDD20 */
- at91_pio3_set_c_periph(AT91_PIO_PORTC, 15, 0); /* LCDD21 */
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 27, 0); /* LCDD22 */
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 28, 0); /* LCDD23 */
-
- /* Configure lower 16 bit of LCD and enable clock */
- at91_lcd_hw_init();
-}
-
-#ifdef CONFIG_LCD_INFO
-#include <nand.h>
-#include <version.h>
-
-void lcd_show_board_info(void)
-{
- ulong dram_size;
- uint64_t nand_size;
- int i;
- char temp[32];
-
- lcd_printf("%s\n", U_BOOT_VERSION);
- lcd_printf("(C) 2013 ATMEL Corp\n");
- lcd_printf("at91@atmel.com\n");
- lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
- strmhz(temp, get_cpu_clk_rate()));
-
- dram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
- dram_size += gd->bd->bi_dram[i].size;
-
- nand_size = 0;
-#ifdef CONFIG_NAND_ATMEL
- for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += get_nand_dev_by_index(i)->size;
-#endif
- lcd_printf("%ld MB SDRAM, %lld MB NAND\n",
- dram_size >> 20, nand_size >> 20);
-}
-#endif /* CONFIG_LCD_INFO */
-#endif /* CONFIG_LCD */
-
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
@@ -240,10 +164,6 @@
#ifdef CONFIG_GENERIC_ATMEL_MCI
sama5d3xek_mci_hw_init();
#endif
-#ifdef CONFIG_LCD
- if (has_lcdc())
- sama5d3xek_lcd_hw_init();
-#endif
return 0;
}
@@ -269,6 +189,9 @@
strcat(name, "ek.dtb");
env_set("dtb_name", name);
#endif
+#ifdef CONFIG_DM_VIDEO
+ at91_video_show_board_info();
+#endif
return 0;
}
#endif