blob: b168b247bd17cd4c8b728775af1058a3687240c1 [file] [log] [blame]
Matthias Fuchs15a08bc2008-01-17 10:52:30 +01001/*
2 * (C) Copyright 2008
3 * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com
4 *
Wolfgang Denk1a459662013-07-08 09:37:19 +02005 * SPDX-License-Identifier: GPL-2.0+
Matthias Fuchs15a08bc2008-01-17 10:52:30 +01006 */
7
8#include <common.h>
9#include <asm/processor.h>
10#include <asm/io.h>
11#include <asm/bitops.h>
12#include <command.h>
13#include <i2c.h>
Stefan Roeseb36df562010-09-09 19:18:00 +020014#include <asm/ppc440.h>
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010015#include "du440.h"
16
17DECLARE_GLOBAL_DATA_PTR;
18
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020019extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010020extern ulong flash_get_size (ulong base, int banknum);
21
22int usbhub_init(void);
23int dvi_init(void);
24int eeprom_write_enable (unsigned dev_addr, int state);
25int board_revision(void);
26
27static int du440_post_errors;
28
29int board_early_init_f(void)
30{
31 u32 sdr0_cust0;
32 u32 sdr0_pfc1, sdr0_pfc2;
33 u32 reg;
34
Stefan Roesed1c3b272009-09-09 16:25:29 +020035 mtdcr(EBC0_CFGADDR, EBC0_CFG);
36 mtdcr(EBC0_CFGDATA, 0xb8400000);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010037
38 /*
39 * Setup the GPIO pins
40 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020041 out_be32((void*)GPIO0_OR, 0x00000000 | CONFIG_SYS_GPIO0_EP_EEP);
42 out_be32((void*)GPIO0_TCR, 0x0000001f | CONFIG_SYS_GPIO0_EP_EEP);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010043 out_be32((void*)GPIO0_OSRL, 0x50055400);
Matthias Fuchs6a133d62008-10-07 13:13:08 +020044 out_be32((void*)GPIO0_OSRH, 0x55005000);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010045 out_be32((void*)GPIO0_TSRL, 0x50055400);
46 out_be32((void*)GPIO0_TSRH, 0x55005000);
47 out_be32((void*)GPIO0_ISR1L, 0x50000000);
48 out_be32((void*)GPIO0_ISR1H, 0x00000000);
49 out_be32((void*)GPIO0_ISR2L, 0x00000000);
Matthias Fuchs6a133d62008-10-07 13:13:08 +020050 out_be32((void*)GPIO0_ISR2H, 0x00000000);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010051 out_be32((void*)GPIO0_ISR3L, 0x00000000);
52 out_be32((void*)GPIO0_ISR3H, 0x00000000);
53
54 out_be32((void*)GPIO1_OR, 0x00000000);
55 out_be32((void*)GPIO1_TCR, 0xc2000000 |
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +020056 CONFIG_SYS_GPIO1_IORSTN |
57 CONFIG_SYS_GPIO1_IORST2N |
58 CONFIG_SYS_GPIO1_LEDUSR1 |
59 CONFIG_SYS_GPIO1_LEDUSR2 |
60 CONFIG_SYS_GPIO1_LEDPOST |
61 CONFIG_SYS_GPIO1_LEDDU);
62 out_be32((void*)GPIO1_ODR, CONFIG_SYS_GPIO1_LEDDU);
Matthias Fuchs6a133d62008-10-07 13:13:08 +020063 out_be32((void*)GPIO1_OSRL, 0x0c280000);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010064 out_be32((void*)GPIO1_OSRH, 0x00000000);
Matthias Fuchs6a133d62008-10-07 13:13:08 +020065 out_be32((void*)GPIO1_TSRL, 0xcc000000);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010066 out_be32((void*)GPIO1_TSRH, 0x00000000);
67 out_be32((void*)GPIO1_ISR1L, 0x00005550);
68 out_be32((void*)GPIO1_ISR1H, 0x00000000);
69 out_be32((void*)GPIO1_ISR2L, 0x00050000);
70 out_be32((void*)GPIO1_ISR2H, 0x00000000);
71 out_be32((void*)GPIO1_ISR3L, 0x01400000);
72 out_be32((void*)GPIO1_ISR3H, 0x00000000);
73
74 /*
75 * Setup the interrupt controller polarities, triggers, etc.
76 */
Stefan Roese952e7762009-09-24 09:55:50 +020077 mtdcr(UIC0SR, 0xffffffff); /* clear all */
78 mtdcr(UIC0ER, 0x00000000); /* disable all */
79 mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */
80 mtdcr(UIC0PR, 0xfffff7ff); /* per ref-board manual */
81 mtdcr(UIC0TR, 0x00000000); /* per ref-board manual */
82 mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */
83 mtdcr(UIC0SR, 0xffffffff); /* clear all */
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010084
85 /*
86 * UIC1:
87 * bit30: ext. Irq 1: PLD : int 32+30
88 */
Stefan Roese952e7762009-09-24 09:55:50 +020089 mtdcr(UIC1SR, 0xffffffff); /* clear all */
90 mtdcr(UIC1ER, 0x00000000); /* disable all */
91 mtdcr(UIC1CR, 0x00000000); /* all non-critical */
92 mtdcr(UIC1PR, 0xfffffffd);
93 mtdcr(UIC1TR, 0x00000000);
94 mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
95 mtdcr(UIC1SR, 0xffffffff); /* clear all */
Matthias Fuchs15a08bc2008-01-17 10:52:30 +010096
97 /*
98 * UIC2
99 * bit3: ext. Irq 2: DCF77 : int 64+3
100 */
Stefan Roese952e7762009-09-24 09:55:50 +0200101 mtdcr(UIC2SR, 0xffffffff); /* clear all */
102 mtdcr(UIC2ER, 0x00000000); /* disable all */
103 mtdcr(UIC2CR, 0x00000000); /* all non-critical */
104 mtdcr(UIC2PR, 0xffffffff); /* per ref-board manual */
105 mtdcr(UIC2TR, 0x00000000); /* per ref-board manual */
106 mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
107 mtdcr(UIC2SR, 0xffffffff); /* clear all */
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100108
109 /* select Ethernet pins */
110 mfsdr(SDR0_PFC1, sdr0_pfc1);
111 mfsdr(SDR0_PFC2, sdr0_pfc2);
112
113 /* setup EMAC bridge interface */
114 if (board_revision() == 0) {
115 /* 1 x MII */
116 sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
117 SDR0_PFC1_SELECT_CONFIG_1_2;
118 sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
119 SDR0_PFC2_SELECT_CONFIG_1_2;
120 } else {
121 /* 2 x SMII */
122 sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
123 SDR0_PFC1_SELECT_CONFIG_6;
124 sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
125 SDR0_PFC2_SELECT_CONFIG_6;
126 }
127
128 /* enable 2nd IIC */
129 sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL;
130
131 mtsdr(SDR0_PFC2, sdr0_pfc2);
132 mtsdr(SDR0_PFC1, sdr0_pfc1);
133
134 /* PCI arbiter enabled */
Stefan Roesed1c3b272009-09-09 16:25:29 +0200135 mfsdr(SDR0_PCI0, reg);
136 mtsdr(SDR0_PCI0, 0x80000000 | reg);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100137
138 /* setup NAND FLASH */
139 mfsdr(SDR0_CUST0, sdr0_cust0);
140 sdr0_cust0 = SDR0_CUST0_MUX_NDFC_SEL |
141 SDR0_CUST0_NDFC_ENABLE |
142 SDR0_CUST0_NDFC_BW_8_BIT |
143 SDR0_CUST0_NDFC_ARE_MASK |
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200144 (0x80000000 >> (28 + CONFIG_SYS_NAND0_CS)) |
145 (0x80000000 >> (28 + CONFIG_SYS_NAND1_CS));
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100146 mtsdr(SDR0_CUST0, sdr0_cust0);
147
148 return 0;
149}
150
151int misc_init_r(void)
152{
153 uint pbcr;
154 int size_val = 0;
155 u32 reg;
156 unsigned long usb2d0cr = 0;
157 unsigned long usb2phy0cr, usb2h0cr = 0;
158 unsigned long sdr0_pfc1;
Matthias Fuchs542b3852008-10-07 13:13:10 +0200159 unsigned long sdr0_srst0, sdr0_srst1;
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100160 int i, j;
161
162 /* adjust flash start and offset */
163 gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
164 gd->bd->bi_flashoffset = 0;
165
Stefan Roesed1c3b272009-09-09 16:25:29 +0200166 mtdcr(EBC0_CFGADDR, PB0CR);
167 pbcr = mfdcr(EBC0_CFGDATA);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100168 size_val = ffs(gd->bd->bi_flashsize) - 21;
169 pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
Stefan Roesed1c3b272009-09-09 16:25:29 +0200170 mtdcr(EBC0_CFGADDR, PB0CR);
171 mtdcr(EBC0_CFGDATA, pbcr);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100172
173 /*
174 * Re-check to get correct base address
175 */
176 flash_get_size(gd->bd->bi_flashstart, 0);
177
178 /*
179 * USB suff...
180 */
181 /* SDR Setting */
182 mfsdr(SDR0_PFC1, sdr0_pfc1);
183 mfsdr(SDR0_USB0, usb2d0cr);
184 mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
185 mfsdr(SDR0_USB2H0CR, usb2h0cr);
186
187 usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
188 usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;
189 usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
190 usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;
191 usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
192 usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;
193 usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
194 usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;
195 usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
196 usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;
197
198 /* An 8-bit/60MHz interface is the only possible alternative
199 when connecting the Device to the PHY */
200 usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
201 usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;
202
203 /* To enable the USB 2.0 Device function through the UTMI interface */
204 usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
205
206 sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
207 sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL;
208
209 mtsdr(SDR0_PFC1, sdr0_pfc1);
210 mtsdr(SDR0_USB0, usb2d0cr);
211 mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
212 mtsdr(SDR0_USB2H0CR, usb2h0cr);
213
Matthias Fuchs542b3852008-10-07 13:13:10 +0200214 /*
215 * Take USB out of reset:
216 * -Initial status = all cores are in reset
217 * -deassert reset to OPB1, P4OPB0, OPB2, PLB42OPB1 OPB2PLB40 cores
218 * -wait 1 ms
219 * -deassert reset to PHY
220 * -wait 1 ms
221 * -deassert reset to HOST
222 * -wait 4 ms
223 * -deassert all other resets
224 */
225 mfsdr(SDR0_SRST1, sdr0_srst1);
226 sdr0_srst1 &= ~(SDR0_SRST1_OPBA1 | \
227 SDR0_SRST1_P4OPB0 | \
228 SDR0_SRST1_OPBA2 | \
229 SDR0_SRST1_PLB42OPB1 | \
230 SDR0_SRST1_OPB2PLB40);
231 mtsdr(SDR0_SRST1, sdr0_srst1);
232 udelay(1000);
233
234 mfsdr(SDR0_SRST1, sdr0_srst1);
235 sdr0_srst1 &= ~SDR0_SRST1_USB20PHY;
236 mtsdr(SDR0_SRST1, sdr0_srst1);
237 udelay(1000);
238
239 mfsdr(SDR0_SRST0, sdr0_srst0);
240 sdr0_srst0 &= ~SDR0_SRST0_USB2H;
241 mtsdr(SDR0_SRST0, sdr0_srst0);
242 udelay(4000);
243
244 /* finally all the other resets */
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100245 mtsdr(SDR0_SRST1, 0x00000000);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100246 mtsdr(SDR0_SRST0, 0x00000000);
247
248 printf("USB: Host(int phy)\n");
249
250 /*
251 * Clear PLB4A0_ACR[WRP]
252 * This fix will make the MAL burst disabling patch for the Linux
253 * EMAC driver obsolete.
254 */
Stefan Roese5e7abce2010-09-11 09:31:43 +0200255 reg = mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_WRP_MASK;
256 mtdcr(PLB4A0_ACR, reg);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100257
258 /*
259 * release IO-RST#
260 * We have to wait at least 560ms until we may call usbhub_init
261 */
Matthias Fuchs7c91f512008-03-30 18:01:15 +0200262 out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) |
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200263 CONFIG_SYS_GPIO1_IORSTN | CONFIG_SYS_GPIO1_IORST2N);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100264
265 /*
266 * flash USR1/2 LEDs (600ms)
267 * This results in the necessary delay from IORST# until
268 * calling usbhub_init will succeed
269 */
270 for (j = 0; j < 3; j++) {
271 out_be32((void*)GPIO1_OR,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200272 (in_be32((void*)GPIO1_OR) & ~CONFIG_SYS_GPIO1_LEDUSR2) |
273 CONFIG_SYS_GPIO1_LEDUSR1);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100274
275 for (i = 0; i < 100; i++)
276 udelay(1000);
277
278 out_be32((void*)GPIO1_OR,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200279 (in_be32((void*)GPIO1_OR) & ~CONFIG_SYS_GPIO1_LEDUSR1) |
280 CONFIG_SYS_GPIO1_LEDUSR2);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100281
282 for (i = 0; i < 100; i++)
283 udelay(1000);
284 }
285
286 out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) &
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200287 ~(CONFIG_SYS_GPIO1_LEDUSR1 | CONFIG_SYS_GPIO1_LEDUSR2));
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100288
289 if (usbhub_init())
290 du440_post_errors++;
291
292 if (dvi_init())
293 du440_post_errors++;
294
295 return 0;
296}
297
298int pld_revision(void)
299{
Matthias Fuchsbb57ad42009-02-20 10:19:19 +0100300 out_8((void *)CONFIG_SYS_CPLD_BASE, 0x00);
301 return (int)(in_8((void *)CONFIG_SYS_CPLD_BASE) & CPLD_VERSION_MASK);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100302}
303
304int board_revision(void)
305{
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200306 int rpins = (int)((in_be32((void*)GPIO1_IR) & CONFIG_SYS_GPIO1_HWVER_MASK)
307 >> CONFIG_SYS_GPIO1_HWVER_SHIFT);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100308
309 return ((rpins & 1) << 3) | ((rpins & 2) << 1) |
310 ((rpins & 4) >> 1) | ((rpins & 8) >> 3);
311}
312
313#if defined(CONFIG_SHOW_ACTIVITY)
314void board_show_activity (ulong timestamp)
315{
316 if ((timestamp % 100) == 0)
317 out_be32((void*)GPIO1_OR,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200318 in_be32((void*)GPIO1_OR) ^ CONFIG_SYS_GPIO1_LEDUSR1);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100319}
320
321void show_activity(int arg)
322{
323}
324#endif /* CONFIG_SHOW_ACTIVITY */
325
326int du440_phy_addr(int devnum)
327{
328 if (board_revision() == 0)
329 return devnum;
330
331 return devnum + 1;
332}
333
334int checkboard(void)
335{
336 char serno[32];
337
338 puts("Board: DU440");
339
Wolfgang Denkcdb74972010-07-24 21:55:43 +0200340 if (getenv_f("serial#", serno, sizeof(serno)) > 0) {
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100341 puts(", serial# ");
342 puts(serno);
343 }
344
345 printf(", HW-Rev. 1.%d, CPLD-Rev. 1.%d\n",
346 board_revision(), pld_revision());
347 return (0);
348}
349
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100350int last_stage_init(void)
351{
352 int e, i;
353
354 /* everyting is ok: turn on POST-LED */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200355 out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) | CONFIG_SYS_GPIO1_LEDPOST);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100356
357 /* slowly blink on errors and finally keep LED off */
358 for (e = 0; e < du440_post_errors; e++) {
359 out_be32((void*)GPIO1_OR,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200360 in_be32((void*)GPIO1_OR) | CONFIG_SYS_GPIO1_LEDPOST);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100361
362 for (i = 0; i < 500; i++)
363 udelay(1000);
364
365 out_be32((void*)GPIO1_OR,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200366 in_be32((void*)GPIO1_OR) & ~CONFIG_SYS_GPIO1_LEDPOST);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100367
368 for (i = 0; i < 500; i++)
369 udelay(1000);
370 }
371
372 return 0;
373}
374
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100375/*
376 * read field strength from I2C ADC
377 */
378int dcf77_status(void)
379{
380 unsigned int oldbus;
381 uchar u[2];
382 int mv;
383
384 oldbus = I2C_GET_BUS();
385 I2C_SET_BUS(1);
386
387 if (i2c_read (IIC1_MCP3021_ADDR, 0, 0, u, 2)) {
388 I2C_SET_BUS(oldbus);
389 return -1;
390 }
391
392 mv = (int)(((u[0] << 8) | u[1]) >> 2) * 3300 / 1024;
393
394 I2C_SET_BUS(oldbus);
395 return mv;
396}
397
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200398int do_dcf77(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100399{
400 int mv;
401 u32 pin, pinold;
402 unsigned long long t1, t2;
403 bd_t *bd = gd->bd;
404
405 printf("DCF77: ");
406 mv = dcf77_status();
407 if (mv > 0)
408 printf("signal=%d mV\n", mv);
409 else
410 printf("ERROR - no signal\n");
411
412 t1 = t2 = 0;
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200413 pinold = in_be32((void*)GPIO1_IR) & CONFIG_SYS_GPIO1_DCF77;
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100414 while (!ctrlc()) {
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200415 pin = in_be32((void*)GPIO1_IR) & CONFIG_SYS_GPIO1_DCF77;
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100416 if (pin && !pinold) { /* bit start */
417 t1 = get_ticks();
418 if (t2 && ((unsigned int)(t1 - t2) /
419 (bd->bi_procfreq / 1000) >= 1800))
420 printf("Start of minute\n");
421
422 t2 = t1;
423 }
424 if (t1 && !pin && pinold) { /* bit end */
425 printf("%5d\n", (unsigned int)(get_ticks() - t1) /
426 (bd->bi_procfreq / 1000));
427 }
428 pinold = pin;
429 }
430
431 printf("Abort\n");
432 return 0;
433}
434U_BOOT_CMD(
435 dcf77, 1, 1, do_dcf77,
Peter Tyser2fb26042009-01-27 18:03:12 -0600436 "Check DCF77 receiver",
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200437 ""
438);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100439
440/*
441 * initialize USB hub via I2C1
442 */
443int usbhub_init(void)
444{
445 int reg;
446 int ret = 0;
447 unsigned int oldbus;
448 uchar u[] = {0x04, 0x24, 0x04, 0x07, 0x25, 0x00, 0x00, 0xd3,
449 0x18, 0xe0, 0x00, 0x00, 0x01, 0x64, 0x01, 0x64,
450 0x32};
451 uchar stcd;
452
453 printf("Hub: ");
454
455 oldbus = I2C_GET_BUS();
456 I2C_SET_BUS(1);
457
458 for (reg = 0; reg < sizeof(u); reg++)
459 if (i2c_write (IIC1_USB2507_ADDR, reg, 1, &u[reg], 1)) {
460 ret = -1;
461 break;
462 }
463
464 if (ret == 0) {
465 stcd = 0x03;
466 if (i2c_write (IIC1_USB2507_ADDR, 0, 1, &stcd, 1))
467 ret = -1;
468 }
469
470 if (ret == 0)
471 printf("initialized\n");
472 else
473 printf("failed - cannot initialize USB hub\n");
474
475 I2C_SET_BUS(oldbus);
476 return ret;
477}
478
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200479int do_hubinit(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100480{
481 usbhub_init();
482 return 0;
483}
484U_BOOT_CMD(
485 hubinit, 1, 1, do_hubinit,
Peter Tyser2fb26042009-01-27 18:03:12 -0600486 "Initialize USB hub",
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200487 ""
488);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100489
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200490#define CONFIG_SYS_BOOT_EEPROM_PAGE_WRITE_BITS 3
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100491int boot_eeprom_write (unsigned dev_addr,
492 unsigned offset,
493 uchar *buffer,
494 unsigned cnt)
495{
496 unsigned end = offset + cnt;
497 unsigned blk_off;
498 int rcode = 0;
499
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200500#if defined(CONFIG_SYS_EEPROM_WREN)
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100501 eeprom_write_enable(dev_addr, 1);
502#endif
503 /*
504 * Write data until done or would cross a write page boundary.
505 * We must write the address again when changing pages
506 * because the address counter only increments within a page.
507 */
508
509 while (offset < end) {
510 unsigned alen, len;
511 unsigned maxlen;
512
513 uchar addr[2];
514
515 blk_off = offset & 0xFF; /* block offset */
516
517 addr[0] = offset >> 8; /* block number */
518 addr[1] = blk_off; /* block offset */
519 alen = 2;
520 addr[0] |= dev_addr; /* insert device address */
521
522 len = end - offset;
523
524 /*
525 * For a FRAM device there is no limit on the number of the
526 * bytes that can be ccessed with the single read or write
527 * operation.
528 */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200529#if defined(CONFIG_SYS_BOOT_EEPROM_PAGE_WRITE_BITS)
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100530
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200531#define BOOT_EEPROM_PAGE_SIZE (1 << CONFIG_SYS_BOOT_EEPROM_PAGE_WRITE_BITS)
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100532#define BOOT_EEPROM_PAGE_OFFSET(x) ((x) & (BOOT_EEPROM_PAGE_SIZE - 1))
533
534 maxlen = BOOT_EEPROM_PAGE_SIZE -
535 BOOT_EEPROM_PAGE_OFFSET(blk_off);
536#else
537 maxlen = 0x100 - blk_off;
538#endif
539 if (maxlen > I2C_RXTX_LEN)
540 maxlen = I2C_RXTX_LEN;
541
542 if (len > maxlen)
543 len = maxlen;
544
545 if (i2c_write (addr[0], offset, alen - 1, buffer, len) != 0)
546 rcode = 1;
547
548 buffer += len;
549 offset += len;
550
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200551#if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
552 udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100553#endif
554 }
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200555#if defined(CONFIG_SYS_EEPROM_WREN)
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100556 eeprom_write_enable(dev_addr, 0);
557#endif
558 return rcode;
559}
560
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200561int do_setup_boot_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100562{
563 ulong sdsdp[4];
564
565 if (argc > 1) {
566 if (!strcmp(argv[1], "533")) {
567 printf("Bootstrapping for 533MHz\n");
568 sdsdp[0] = 0x87788252;
569 /* PLB-PCI-divider = 3 : sync PCI clock=44MHz */
570 sdsdp[1] = 0x095fa030;
571 sdsdp[2] = 0x40082350;
572 sdsdp[3] = 0x0d050000;
573 } else if (!strcmp(argv[1], "533-66")) {
574 printf("Bootstrapping for 533MHz (66MHz PCI)\n");
575 sdsdp[0] = 0x87788252;
576 /* PLB-PCI-divider = 2 : sync PCI clock=66MHz */
577 sdsdp[1] = 0x0957a030;
578 sdsdp[2] = 0x40082350;
579 sdsdp[3] = 0x0d050000;
580 } else if (!strcmp(argv[1], "667")) {
581 printf("Bootstrapping for 667MHz\n");
582 sdsdp[0] = 0x8778a256;
583 /* PLB-PCI-divider = 4 : sync PCI clock=33MHz */
584 sdsdp[1] = 0x0947a030;
585 /* PLB-PCI-divider = 3 : sync PCI clock=44MHz
586 * -> not working when overclocking 533MHz chips
587 * -> untested on 667MHz chips */
588 /* sdsdp[1]=0x095fa030; */
589 sdsdp[2] = 0x40082350;
590 sdsdp[3] = 0x0d050000;
Matthias Fuchsdf8c1ce2008-10-07 13:13:09 +0200591 } else if (!strcmp(argv[1], "667-166")) {
592 printf("Bootstrapping for 667-166MHz\n");
593 sdsdp[0] = 0x8778a252;
594 sdsdp[1] = 0x09d7a030;
595 sdsdp[2] = 0x40082350;
596 sdsdp[3] = 0x0d050000;
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100597 }
598 } else {
599 printf("Bootstrapping for 533MHz (default)\n");
600 sdsdp[0] = 0x87788252;
601 /* PLB-PCI-divider = 3 : sync PCI clock=44MHz */
602 sdsdp[1] = 0x095fa030;
603 sdsdp[2] = 0x40082350;
604 sdsdp[3] = 0x0d050000;
605 }
606
607 printf("Writing boot EEPROM ...\n");
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200608 if (boot_eeprom_write(CONFIG_SYS_I2C_BOOT_EEPROM_ADDR,
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100609 0, (uchar*)sdsdp, 16) != 0)
610 printf("boot_eeprom_write failed\n");
611 else
612 printf("done (dump via 'i2c md 52 0.1 10')\n");
613
614 return 0;
615}
616U_BOOT_CMD(
617 sbe, 2, 0, do_setup_boot_eeprom,
Peter Tyser2fb26042009-01-27 18:03:12 -0600618 "setup boot eeprom",
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200619 ""
620);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100621
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200622#if defined(CONFIG_SYS_EEPROM_WREN)
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100623/*
624 * Input: <dev_addr> I2C address of EEPROM device to enable.
625 * <state> -1: deliver current state
626 * 0: disable write
627 * 1: enable write
628 * Returns: -1: wrong device address
629 * 0: dis-/en- able done
630 * 0/1: current state if <state> was -1.
631 */
632int eeprom_write_enable (unsigned dev_addr, int state)
633{
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200634 if ((CONFIG_SYS_I2C_EEPROM_ADDR != dev_addr) &&
635 (CONFIG_SYS_I2C_BOOT_EEPROM_ADDR != dev_addr))
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100636 return -1;
637 else {
638 switch (state) {
639 case 1:
640 /* Enable write access, clear bit GPIO_SINT2. */
641 out_be32((void*)GPIO0_OR,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200642 in_be32((void*)GPIO0_OR) & ~CONFIG_SYS_GPIO0_EP_EEP);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100643 state = 0;
644 break;
645 case 0:
646 /* Disable write access, set bit GPIO_SINT2. */
647 out_be32((void*)GPIO0_OR,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200648 in_be32((void*)GPIO0_OR) | CONFIG_SYS_GPIO0_EP_EEP);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100649 state = 0;
650 break;
651 default:
652 /* Read current status back. */
653 state = (0 == (in_be32((void*)GPIO0_OR) &
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200654 CONFIG_SYS_GPIO0_EP_EEP));
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100655 break;
656 }
657 }
658 return state;
659}
660
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200661int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100662{
663 int query = argc == 1;
664 int state = 0;
665
666 if (query) {
667 /* Query write access state. */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200668 state = eeprom_write_enable(CONFIG_SYS_I2C_EEPROM_ADDR, -1);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100669 if (state < 0)
670 puts ("Query of write access state failed.\n");
671 else {
672 printf ("Write access for device 0x%0x is %sabled.\n",
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200673 CONFIG_SYS_I2C_EEPROM_ADDR, state ? "en" : "dis");
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100674 state = 0;
675 }
676 } else {
677 if ('0' == argv[1][0]) {
678 /* Disable write access. */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200679 state = eeprom_write_enable(CONFIG_SYS_I2C_EEPROM_ADDR, 0);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100680 } else {
681 /* Enable write access. */
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200682 state = eeprom_write_enable(CONFIG_SYS_I2C_EEPROM_ADDR, 1);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100683 }
684 if (state < 0)
685 puts ("Setup of write access state failed.\n");
686 }
687
688 return state;
689}
690
691U_BOOT_CMD(eepwren, 2, 0, do_eep_wren,
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200692 "Enable / disable / query EEPROM write access",
693 ""
694);
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200695#endif /* #if defined(CONFIG_SYS_EEPROM_WREN) */
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100696
697static int got_pldirq;
698
699static int pld_interrupt(u32 arg)
700{
701 int rc = -1; /* not for us */
Matthias Fuchsbb57ad42009-02-20 10:19:19 +0100702 u8 status = in_8((void *)CONFIG_SYS_CPLD_BASE);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100703
704 /* check for PLD interrupt */
705 if (status & PWR_INT_FLAG) {
706 /* reset this int */
Matthias Fuchsbb57ad42009-02-20 10:19:19 +0100707 out_8((void *)CONFIG_SYS_CPLD_BASE, 0);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100708 rc = 0;
709 got_pldirq = 1; /* trigger backend */
710 }
711
712 return rc;
713}
714
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200715int do_waitpwrirq(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100716{
717 got_pldirq = 0;
718
719 /* clear any pending interrupt */
Matthias Fuchsbb57ad42009-02-20 10:19:19 +0100720 out_8((void *)CONFIG_SYS_CPLD_BASE, 0);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100721
722 irq_install_handler(CPLD_IRQ,
723 (interrupt_handler_t *)pld_interrupt, 0);
724
725 printf("Waiting ...\n");
726 while(!got_pldirq) {
727 /* Abort if ctrl-c was pressed */
728 if (ctrlc()) {
729 puts("\nAbort\n");
730 break;
731 }
732 }
733 if (got_pldirq) {
734 printf("Got interrupt!\n");
735 printf("Power %sready!\n",
Matthias Fuchsbb57ad42009-02-20 10:19:19 +0100736 in_8((void *)CONFIG_SYS_CPLD_BASE) &
737 PWR_RDY ? "":"NOT ");
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100738 }
739
740 irq_free_handler(CPLD_IRQ);
741 return 0;
742}
743U_BOOT_CMD(
744 wpi, 1, 1, do_waitpwrirq,
Peter Tyser2fb26042009-01-27 18:03:12 -0600745 "Wait for power change interrupt",
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200746 ""
747);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100748
749/*
750 * initialize DVI panellink transmitter
751 */
752int dvi_init(void)
753{
754 int i;
755 int ret = 0;
756 unsigned int oldbus;
757 uchar u[] = {0x08, 0x34,
758 0x09, 0x20,
759 0x0a, 0x90,
760 0x0c, 0x89,
761 0x08, 0x35};
762
763 printf("DVI: ");
764
765 oldbus = I2C_GET_BUS();
766 I2C_SET_BUS(0);
767
768 for (i = 0; i < sizeof(u); i += 2)
769 if (i2c_write (0x38, u[i], 1, &u[i + 1], 1)) {
770 ret = -1;
771 break;
772 }
773
774 if (ret == 0)
775 printf("initialized\n");
776 else
777 printf("failed - cannot initialize DVI transmitter\n");
778
779 I2C_SET_BUS(oldbus);
780 return ret;
781}
782
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200783int do_dviinit(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100784{
785 dvi_init();
786 return 0;
787}
788U_BOOT_CMD(
789 dviinit, 1, 1, do_dviinit,
Peter Tyser2fb26042009-01-27 18:03:12 -0600790 "Initialize DVI Panellink transmitter",
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200791 ""
792);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100793
794/*
795 * TODO: 'time' command might be useful for others as well.
796 * Move to 'common' directory.
797 */
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200798int do_time(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100799{
800 unsigned long long start, end;
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200801 char c, cmd[CONFIG_SYS_CBSIZE];
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100802 char *p, *d = cmd;
803 int ret, i;
804 ulong us;
805
806 for (i = 1; i < argc; i++) {
807 p = argv[i];
808
809 if (i > 1)
810 *d++ = ' ';
811
812 while ((c = *p++) != '\0') {
813 *d++ = c;
814 }
815 }
816 *d = '\0';
817
818 start = get_ticks();
Simon Glass53071532012-02-14 19:59:21 +0000819 ret = run_command(cmd, 0);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100820 end = get_ticks();
821
Stefan Roeseb0021442008-07-10 09:58:06 +0200822 printf("ticks=%ld\n", (ulong)(end - start));
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100823 us = (ulong)((1000L * (end - start)) / (get_tbclk() / 1000));
Stefan Roeseb0021442008-07-10 09:58:06 +0200824 printf("usec=%ld\n", us);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100825
826 return ret;
827}
828U_BOOT_CMD(
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200829 time, CONFIG_SYS_MAXARGS, 1, do_time,
Peter Tyser2fb26042009-01-27 18:03:12 -0600830 "run command and output execution time",
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200831 ""
832);
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100833
834extern void video_hw_rectfill (
835 unsigned int bpp, /* bytes per pixel */
836 unsigned int dst_x, /* dest pos x */
837 unsigned int dst_y, /* dest pos y */
838 unsigned int dim_x, /* frame width */
839 unsigned int dim_y, /* frame height */
840 unsigned int color /* fill color */
841 );
842
843/*
844 * graphics demo
845 * draw rectangles using pseudorandom number generator
846 * (see http://www.embedded.com/columns/technicalinsights/20900500)
847 */
848unsigned int rprime = 9972;
849static unsigned int r;
850static unsigned int Y;
851
852unsigned int prng(unsigned int max)
853{
854 if (r == 0 || r == 1 || r == -1)
855 r = rprime; /* keep from getting stuck */
856
857 r = (9973 * ~r) + ((Y) % 701); /* the actual algorithm */
858 Y = (r >> 16) % max; /* choose upper bits and reduce */
859 return Y;
860}
861
Wolfgang Denk54841ab2010-06-28 22:00:46 +0200862int do_gfxdemo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
Matthias Fuchs15a08bc2008-01-17 10:52:30 +0100863{
864 unsigned int color;
865 unsigned int x, y, dx, dy;
866
867 while (!ctrlc()) {
868 x = prng(1280 - 1);
869 y = prng(1024 - 1);
870 dx = prng(1280- x - 1);
871 dy = prng(1024 - y - 1);
872 color = prng(0x10000);
873 video_hw_rectfill(2, x, y, dx, dy, color);
874 }
875
876 return 0;
877}
878U_BOOT_CMD(
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200879 gfxdemo, CONFIG_SYS_MAXARGS, 1, do_gfxdemo,
Peter Tyser2fb26042009-01-27 18:03:12 -0600880 "demo",
Wolfgang Denka89c33d2009-05-24 17:06:54 +0200881 ""
882);