blob: bfb3156f6f672fa6b39c41f624e0a28692b65661 [file] [log] [blame]
wdenke2211742002-11-02 23:30:20 +00001/*
2 * (C) Copyright 2001
3 * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com
4 *
5 * See file CREDITS for list of people who contributed to this
6 * project.
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21 * MA 02111-1307 USA
22 */
23
24/*
25 * board/config.h - configuration options, board specific
26 */
27
28#ifndef __CONFIG_H
29#define __CONFIG_H
30
31/*
32 * High Level Configuration Options
33 * (easy to change)
34 */
35
36#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
37#define CONFIG_4xx 1 /* ...member of PPC405 family */
38#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */
39#define CONFIG_W7OLMG 1 /* ...specifically an LMG */
40
wdenkc837dcb2004-01-20 23:12:12 +000041#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
42#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */
wdenke2211742002-11-02 23:30:20 +000043
44#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
45
46#define CONFIG_BAUDRATE 9600
47#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
48
49#if 1
50#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */
51#else
52#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
53#endif
54
55#undef CONFIG_BOOTARGS
56
57#define CONFIG_LOADADDR F0080000
58
59#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */
60#define CONFIG_OVERWRITE_ETHADDR_ONCE
61#define CONFIG_IPADDR 192.168.1.1
62#define CONFIG_NETMASK 255.255.255.0
63#define CONFIG_SERVERIP 192.168.1.2
64
65#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
66#undef CFG_LOADS_BAUD_CHANGE /* disallow baudrate change */
67
68#define CONFIG_MII 1 /* MII PHY management */
69#define CONFIG_PHY_ADDR 0 /* PHY address */
70
71#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
72#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
73#define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */
74#define CFG_DTT_MAX_TEMP 70
75#define CFG_DTT_LOW_TEMP -30
76#define CFG_DTT_HYSTERESIS 3
77
wdenke2211742002-11-02 23:30:20 +000078
Jon Loeligera5562902007-07-08 15:31:57 -050079/*
Jon Loeligera1aa0bb2007-07-10 09:22:23 -050080 * BOOTP options
81 */
82#define CONFIG_BOOTP_BOOTFILESIZE
83#define CONFIG_BOOTP_BOOTPATH
84#define CONFIG_BOOTP_GATEWAY
85#define CONFIG_BOOTP_HOSTNAME
86
87
88/*
Jon Loeligera5562902007-07-08 15:31:57 -050089 * Command line configuration.
90 */
91#include <config_cmd_default.h>
92
93#define CONFIG_CMD_PCI
94#define CONFIG_CMD_IRQ
95#define CONFIG_CMD_ASKENV
96#define CONFIG_CMD_DHCP
97#define CONFIG_CMD_BEDBUG
98#define CONFIG_CMD_DATE
99#define CONFIG_CMD_I2C
100#define CONFIG_CMD_EEPROM
101#define CONFIG_CMD_ELF
102#define CONFIG_CMD_BSP
103#define CONFIG_CMD_REGINFO
104#define CONFIG_CMD_DTT
105
wdenke2211742002-11-02 23:30:20 +0000106
107#undef CONFIG_WATCHDOG /* watchdog disabled */
108#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */
109
110#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */
wdenkdb2f721f2003-03-06 00:58:30 +0000111#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */
wdenke2211742002-11-02 23:30:20 +0000112/*
113 * Miscellaneous configurable options
114 */
115#define CFG_LONGHELP /* undef to save memory */
116#define CFG_PROMPT "Wave7Optics> " /* Monitor Command Prompt */
117#undef CFG_HUSH_PARSER /* No hush parse for U-Boot */
118#ifdef CFG_HUSH_PARSER
119#define CFG_PROMPT_HUSH_PS2 "> "
120#endif
Jon Loeligera5562902007-07-08 15:31:57 -0500121#if defined(CONFIG_CMD_KGDB)
wdenke2211742002-11-02 23:30:20 +0000122#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
123#else
124#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
125#endif
126#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
127#define CFG_MAXARGS 16 /* max number of command args */
128#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
129
130#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
131#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
132
133#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
134#define CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
135#define CFG_BASE_BAUD 384000
136
137
138/* The following table includes the supported baudrates */
139#define CFG_BAUDRATE_TABLE {9600}
140
141#define CFG_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
142
143#define CFG_LOAD_ADDR 0x100000 /* default load address */
144#define CFG_EXTBDINFO 1 /* use extended board_info (bd_t) */
145
146#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
147
148/*-----------------------------------------------------------------------
149 * PCI stuff
150 *-----------------------------------------------------------------------
151 */
152#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
153#define PCI_HOST_FORCE 1 /* configure as pci host */
154#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
155
156#define CONFIG_PCI /* include pci support */
157#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
158#define CONFIG_PCI_PNP /* pci plug-and-play */
159/* resource configuration */
160#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
161#define CFG_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */
162#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
163#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
164#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
165#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
166#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
167#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
168
169/*-----------------------------------------------------------------------
170 * Set up values for external bus controller
171 * used by cpu_init.c
172 *-----------------------------------------------------------------------
173 */
174 /* use PerWE instead of PCI_INT ( these functions share a pin ) */
175#define CONFIG_USE_PERWE 1
176
177/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
178#define CFG_TEMP_STACK_OCM 1
179
180/* bank 0 is boot flash */
181/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
182#define CFG_W7O_EBC_PB0AP 0x03050440
183/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */
184#define CFG_W7O_EBC_PB0CR 0xFFE38000
185
186/* bank 1 is main flash */
187/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */
188#define CFG_EBC_PB1AP 0x04850240
189/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */
190#define CFG_EBC_PB1CR 0xF00FC000
191
192/* bank 2 is RTC/NVRAM */
193/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
194#define CFG_EBC_PB2AP 0x03000440
195/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
196#define CFG_EBC_PB2CR 0xFC018000
197
198/* bank 3 is FPGA 0 */
199/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */
200#define CFG_EBC_PB3AP 0x02000400
201/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */
202#define CFG_EBC_PB3CR 0xFD01A000
203
204/* bank 4 is SAM 8 bit range */
205/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */
206#define CFG_EBC_PB4AP 0x02840380
207/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */
208#define CFG_EBC_PB4CR 0xFE878000
209
210/* bank 5 is SAM 16 bit range */
211/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */
212#define CFG_EBC_PB5AP 0x05040d80
213/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */
214#define CFG_EBC_PB5CR 0xFD87A000
215
216/* bank 6 is unused */
217/* pb6ap = 0 */
218#define CFG_EBC_PB6AP 0x00000000
219/* pb6cr = 0 */
220#define CFG_EBC_PB6CR 0x00000000
221
222/* bank 7 is LED register */
223/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
224#define CFG_W7O_EBC_PB7AP 0x03050440
225/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */
226#define CFG_W7O_EBC_PB7CR 0xFE01C000
227
228/*-----------------------------------------------------------------------
229 * Start addresses for the final memory configuration
230 * (Set up by the startup code)
231 * Please note that CFG_SDRAM_BASE _must_ start at 0
232 */
233#define CFG_SDRAM_BASE 0x00000000
234#define CFG_FLASH_BASE 0xFFFC0000
235#define CFG_MONITOR_BASE CFG_FLASH_BASE
236#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */
237#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
238
239/*
240 * For booting Linux, the board info and command line data
241 * have to be in the first 8 MB of memory, since this is
242 * the maximum mapped by the Linux kernel during initialization.
243 */
244#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
245/*-----------------------------------------------------------------------
246 * FLASH organization
247 */
248#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
249#define CFG_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */
250
251#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */
252#define CFG_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */
253#define CFG_FLASH_PROTECTION 1 /* Use real Flash protection */
254
255#if 1 /* Use NVRAM for environment variables */
256/*-----------------------------------------------------------------------
257 * NVRAM organization
258 */
259#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */
260#define CFG_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */
261#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
262#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
263/*define CFG_ENV_ADDR \
264 (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) Env */
265#define CFG_ENV_ADDR CFG_NVRAM_BASE_ADDR
266
267#else /* Use Boot Flash for environment variables */
268/*-----------------------------------------------------------------------
269 * Flash EEPROM for environment
270 */
271#define CFG_ENV_IS_IN_FLASH 1
272#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
273#define CFG_ENV_SIZE 0x10000 /* Total Size of env. sector */
274
275#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */
276#endif
277
278/*-----------------------------------------------------------------------
279 * I2C EEPROM (ATMEL 24C04N)
280 */
281#define CONFIG_HARD_I2C 1 /* Hardware assisted I2C */
282#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
283#define CFG_I2C_SLAVE 0x7F
284
285#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */
286#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
287#define CFG_EEPROM_PAGE_WRITE_ENABLE
288#define CFG_EEPROM_PAGE_WRITE_BITS 3
289#define CFG_I2C_MULTI_EEPROMS
290/*-----------------------------------------------------------------------
291 * Definitions for Serial Presence Detect EEPROM address
292 * (to get SDRAM settings)
293 */
294#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */
295
wdenke2211742002-11-02 23:30:20 +0000296/*
297 * Init Memory Controller:
298 */
299#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */
300#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */
301
302/* On Chip Memory location */
303#define CFG_OCM_DATA_ADDR 0xF8000000
304#define CFG_OCM_DATA_SIZE 0x1000
305
306/*-----------------------------------------------------------------------
307 * Definitions for initial stack pointer and data area (in RAM)
308 */
309#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
310#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
311#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
312#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
313#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
314
315
316/*
317 * Internal Definitions
318 *
319 * Boot Flags
320 */
321#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
322#define BOOTFLAG_WARM 0x02 /* Software reboot */
323
Jon Loeligera5562902007-07-08 15:31:57 -0500324#if defined(CONFIG_CMD_KGDB)
wdenke2211742002-11-02 23:30:20 +0000325#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
326#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
327#endif
328
329/*
330 * FPGA(s) configuration
331 */
332#define CFG_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */
333#define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */
334#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */
335#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */
336#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */
337
338#endif /* __CONFIG_H */