arch/arm/dts/fsl-ls1028a.dtsi

// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
 * NXP ls1028a SOC common device tree source
 *
 * Copyright 2019-2020 NXP
 *
 */

#include <dt-bindings/interrupt-controller/arm-gic.h>

/ {
	compatible = "fsl,ls1028a";
	interrupt-parent = <&gic>;
	#address-cells = <2>;
	#size-cells = <2>;

	sysclk: sysclk {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <100000000>;
		clock-output-names = "sysclk";
	};

	gic: interrupt-controller@6000000 {
		compatible = "arm,gic-v3";
		reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
			  <0x0 0x06040000 0 0x40000>;
		#interrupt-cells = <3>;
		interrupt-controller;
		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
					 IRQ_TYPE_LEVEL_LOW)>;
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
					  IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
					  IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) |
					  IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
					  IRQ_TYPE_LEVEL_LOW)>;
	};

	pcie@1f0000000 {
		compatible = "pci-host-ecam-generic";
		/* ECAM bus 0, HW has more space reserved but not populated */
		bus-range = <0x0 0x0>;
		reg = <0x01 0xf0000000 0x0 0x100000>;
		#address-cells = <3>;
		#size-cells = <2>;
		device_type = "pci";
		ranges= <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>;
		enetc0: pci@0,0 {
			reg = <0x000000 0 0 0 0>;
			status = "disabled";
		};
		enetc1: pci@0,1 {
			reg = <0x000100 0 0 0 0>;
			status = "disabled";
		};
		enetc2: pci@0,2 {
			reg = <0x000200 0 0 0 0>;
			status = "disabled";
			phy-mode = "internal";

			fixed-link {
				speed = <2500>;
				full-duplex;
			};
		};
		mdio0: pci@0,3 {
			#address-cells=<0>;
			#size-cells=<1>;
			reg = <0x000300 0 0 0 0>;
			status = "disabled";

			fixed-link {
				speed = <1000>;
				full-duplex;
			};
		};

		mscc_felix: pci@0,5 {
			reg = <0x000500 0 0 0 0>;
			status = "disabled";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				mscc_felix_port0: port@0 {
					reg = <0>;
					status = "disabled";
				};

				mscc_felix_port1: port@1 {
					reg = <1>;
					status = "disabled";
				};

				mscc_felix_port2: port@2 {
					reg = <2>;
					status = "disabled";
				};

				mscc_felix_port3: port@3 {
					reg = <3>;
					status = "disabled";
				};

				mscc_felix_port4: port@4 {
					reg = <4>;
					phy-mode = "internal";
					status = "disabled";

					fixed-link {
						speed = <2500>;
						full-duplex;
					};
				};

				mscc_felix_port5: port@5 {
					reg = <5>;
					phy-mode = "internal";
					status = "disabled";

					fixed-link {
						speed = <1000>;
						full-duplex;
					};

				};
			};
		};

		enetc6: pci@0,6 {
			reg = <0x000600 0 0 0 0>;
			status = "disabled";
			phy-mode = "internal";
		};
	};

	cluster1_core0_watchdog: wdt@c000000 {
		compatible = "arm,sp805-wdt";
		reg = <0x0 0xc000000 0x0 0x1000>;
	};

	soc: soc {
		compatible = "simple-bus";
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		clockgen: clocking@1300000 {
			compatible = "fsl,ls1028a-clockgen";
			reg = <0x0 0x1300000 0x0 0xa0000>;
			#clock-cells = <2>;
			clocks = <&sysclk>;
		};

		i2c0: i2c@2000000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2000000 0x0 0x10000>;
			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		i2c1: i2c@2010000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2010000 0x0 0x10000>;
			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		i2c2: i2c@2020000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2020000 0x0 0x10000>;
			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		i2c3: i2c@2030000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2030000 0x0 0x10000>;
			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		i2c4: i2c@2040000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2040000 0x0 0x10000>;
			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		i2c5: i2c@2050000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2050000 0x0 0x10000>;
			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		i2c6: i2c@2060000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2060000 0x0 0x10000>;
			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		i2c7: i2c@2070000 {
			compatible = "fsl,vf610-i2c";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2070000 0x0 0x10000>;
			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "i2c";
			clocks = <&clockgen 4 0>;
			status = "disabled";
		};

		fspi: flexspi@20c0000 {
			compatible = "nxp,lx2160a-fspi";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x20c0000 0x0 0x10000>,
			      <0x0 0x20000000 0x0 0x10000000>;
			reg-names = "fspi_base", "fspi_mmap";
			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
			clock-names = "fspi_en", "fspi";
			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
			status = "disabled";
		};

		dspi0: dspi@2100000 {
			compatible = "fsl,vf610-dspi";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2100000 0x0 0x10000>;
			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "dspi";
			clocks = <&clockgen 4 0>;
			num-cs = <5>;
			litte-endian;
			status = "disabled";
		};

		dspi1: dspi@2110000 {
			compatible = "fsl,vf610-dspi";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2110000 0x0 0x10000>;
			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "dspi";
			clocks = <&clockgen 4 0>;
			num-cs = <5>;
			little-endian;
			status = "disabled";
		};

		dspi2: dspi@2120000 {
			compatible = "fsl,vf610-dspi";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x2120000 0x0 0x10000>;
			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
			clock-names = "dspi";
			clocks = <&clockgen 4 0>;
			num-cs = <5>;
			little-endian;
			status = "disabled";
		};

		esdhc0: esdhc@2140000 {
			compatible = "fsl,esdhc";
			reg = <0x0 0x2140000 0x0 0x10000>;
			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
			big-endian;
			bus-width = <4>;
			status = "disabled";
		};

		esdhc1: esdhc@2150000 {
			compatible = "fsl,esdhc";
			reg = <0x0 0x2150000 0x0 0x10000>;
			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
			big-endian;
			non-removable;
			bus-width = <4>;
			status = "disabled";
		};

		serial0: serial@21c0500 {
			device_type = "serial";
			compatible = "fsl,ns16550", "ns16550a";
			reg = <0x0 0x21c0500 0x0 0x100>;
			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
			status = "disabled";
		};

		serial1: serial@21c0600 {
			device_type = "serial";
			compatible = "fsl,ns16550", "ns16550a";
			reg = <0x0 0x21c0600 0x0 0x100>;
			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
			status = "disabled";
		};

		lpuart0: serial@2260000 {
			compatible = "fsl,ls1021a-lpuart";
			reg = <0x0 0x2260000 0x0 0x1000>;
			interrupts = <0 232 0x4>;
			clocks = <&sysclk>;
			clock-names = "ipg";
			little-endian;
			status = "disabled";
		};

		lpuart1: serial@2270000 {
			compatible = "fsl,ls1021a-lpuart";
			reg = <0x0 0x2270000 0x0 0x1000>;
			interrupts = <0 233 0x4>;
			clocks = <&sysclk>;
			clock-names = "ipg";
			little-endian;
			status = "disabled";
		};

		lpuart2: serial@2280000 {
			compatible = "fsl,ls1021a-lpuart";
			reg = <0x0 0x2280000 0x0 0x1000>;
			interrupts = <0 234 0x4>;
			clocks = <&sysclk>;
			clock-names = "ipg";
			little-endian;
			status = "disabled";
		};

		lpuart3: serial@2290000 {
			compatible = "fsl,ls1021a-lpuart";
			reg = <0x0 0x2290000 0x0 0x1000>;
			interrupts = <0 235 0x4>;
			clocks = <&sysclk>;
			clock-names = "ipg";
			little-endian;
			status = "disabled";
		};

		lpuart4: serial@22a0000 {
			compatible = "fsl,ls1021a-lpuart";
			reg = <0x0 0x22a0000 0x0 0x1000>;
			interrupts = <0 236 0x4>;
			clocks = <&sysclk>;
			clock-names = "ipg";
			little-endian;
			status = "disabled";
		};

		lpuart5: serial@22b0000 {
			compatible = "fsl,ls1021a-lpuart";
			reg = <0x0 0x22b0000 0x0 0x1000>;
			interrupts = <0 237 0x4>;
			clocks = <&sysclk>;
			clock-names = "ipg";
			little-endian;
			status = "disabled";
		};

		gpio0: gpio@2300000 {
			compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio";
			reg = <0x0 0x2300000 0x0 0x10000>;
			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			little-endian;
		};

		gpio1: gpio@2310000 {
			compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio";
			reg = <0x0 0x2310000 0x0 0x10000>;
			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			little-endian;
		};

		gpio2: gpio@2320000 {
			compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio";
			reg = <0x0 0x2320000 0x0 0x10000>;
			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			little-endian;
		};

		usb1: usb3@3100000 {
			compatible = "fsl,layerscape-dwc3";
			reg = <0x0 0x3100000 0x0 0x10000>;
			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
			dr_mode = "host";
			status = "disabled";
		};

		usb2: usb3@3110000 {
			compatible = "fsl,layerscape-dwc3";
			reg = <0x0 0x3110000 0x0 0x10000>;
			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
			dr_mode = "host";
			status = "disabled";
		};

		sata: sata@3200000 {
			compatible = "fsl,ls1028a-ahci";
			reg = <0x0 0x3200000 0x0 0x10000	/* ccsr sata base */
			       0x7 0x100520  0x0 0x4>;		/* ecc sata addr*/
			reg-names = "sata-base", "ecc-addr";
			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
			status = "disabled";
		};

		pcie1: pcie@3400000 {
			compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";
			reg = <0x00 0x03400000 0x0 0x80000
			       0x00 0x03480000 0x0 0x40000   /* lut registers */
			       0x00 0x034c0000 0x0 0x40000   /* pf controls registers */
			       0x80 0x00000000 0x0 0x20000>; /* configuration space */
			reg-names = "dbi", "lut", "ctrl", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			device_type = "pci";
			num-lanes = <4>;
			bus-range = <0x0 0xff>;
			ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000   /* downstream I/O */
				  0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
		};

		pcie2: pcie@3500000 {
			compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";
			reg = <0x00 0x03500000 0x0 0x80000
			       0x00 0x03580000 0x0 0x40000   /* lut registers */
			       0x00 0x035c0000 0x0 0x40000   /* pf controls registers */
			       0x88 0x00000000 0x0 0x20000>; /* configuration space */
			reg-names = "dbi", "lut", "ctrl", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			device_type = "pci";
			num-lanes = <4>;
			bus-range = <0x0 0xff>;
			ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000   /* downstream I/O */
				  0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
		};
	};
};