CHANGELOG

======================================================================
Changes for U-Boot 0.4.8:
======================================================================

* Add support for USB Mass Storage Devices (BBB)
  (tested with USB memory sticks only)

* Avoid flicker on TRAB's VFD

* Add support for SK98xx driver

* Add PCI support for SL8245 board

* Support IceCube board configurations with 1 x AMD AM29LV065 (8 MB)
  or 1 x AM29LV652 (two LV065 in one chip = 16 MB);
  Run IPB at 133 Mhz; adjust the MII clock frequency accordingly

* Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16  MHz)
  to allow for more accurate baudrate settings
  (error now 0.7% at 115 kbps, instead of 3.5% before)

* Patch by Andreas Mohr, 4 Sep 2003:
  Fix a lot of spelling errors

* Add support for PPChameleon Eval Board

* Add support for P3G4 board

* Fix problem with MGT5100 FEC driver: add "early" MAC address
  initialization

* Patch by Yuli Barcohen, 7 Aug 2003:
  check BCSR to detect if the board is configured in PCI mode

======================================================================
Changes for U-Boot 0.4.7:
======================================================================

* Patch by Raghu Krishnaprasad, 7 Aug 2003:
  add support for Adder II MPC852T module

* Patch by George G. Davis, 19 Aug 2003:
  fix TI Innovator/OMAP1510 pin configs

* Patches by Kshitij, 18 Aug 2003
  - add support for arm926ejs cpu core
  - add support for TI OMAP 1610 Innovator Board

* Patch by Yuli Barcohen, 14 Aug 2003:
  add support for bzip2 uncompression

* Add GCC library to examples/Makefile so GCC utility functions will
  be resolved, too

* Add I2C and RTC support for RMU board using software I2C driver
  (because of better response to iprobe command); fix problem with
  "reset" command

* Patch by Matthias Fuchs, 28 Aug 2003:
  Added CONFIG_BOOTP_DNS2 and CONFIG_BOOTP_SEND_HOSTNAME to
  CONFIG_BOOTP_MAKS (see README).

* Fix ICU862 environment problem

* Fix RAM size detection for RMU board

* Implement "reset" for MGT5100/MPC5200 systems

======================================================================
Changes for U-Boot 0.4.6:
======================================================================

* Make Ethernet autonegotiation on INCA-IP work for all clock rates;
  allow selection of clock frequency as "make" target

* Implement memory autosizing code for IceCube boards

* Configure network port on INCA-IP for autonegotiation

* Fix overflow problem in network timeout code

* Patch by Richard Woodruff, 8 Aug 2003:
  Allow crc32 to be used at address 0x000 (crc32_no_comp, too).

======================================================================
Changes for U-Boot 0.4.5:
======================================================================

* Update for TQM board defaults:
  disable clocks_in_mhz, enable boot count limit

* Removed tools/gdb from "make all" target.  Added make target "gdbtools"
  in toplevel directory instead.  Removed astest.c from tools/gdb because
  it is no longer relevant.

* Fix PCI support for MPC5200 / IceCube Board

* Map ISP1362 USB OTG controller for NSCU board

* Patch by Brad Parker, 02 Aug 2003:
  fix sc520_cdp problems

* Implement Boot Cycle Detection (Req. 2.3 of OSDL CGL Reqirements)

* Allow erase command to cross flash bank boundaries

* Patch by Scott McNutt, 21 Jul 2003:
  Add support for LynuxWorks Kernel Downloadable Images (KDIs).
  Both LynxOS and BlueCat linux KDIs are supported.

* Patch by Richard Woodruff, 25 Jul 2003:
  use more reliable reset for OMAP/925T

* Patch by Nye Liu, 25 Jul 2003:
  fix typo in mpc8xx.h

* Patch by Richard Woodruff, 24 Jul 2003:
  Fixes for cmd_nand.c:
  - Fixed null dereferece which could result in incorrect ECC values.
  - Added support for devices with no Ready/Busy signal hooked up.
  - Added OMAP1510 read/write protect handling.
  - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
    for non-JFFS2.
  - Switched default ECC to be JFFS2.

* Allow crc32 to be used at address 0x000

* Provide consistent interface to standalone applications to access
  the 'global_data' structure
  Provide a doc/README.standalone more useful to users/developers.

* Make IceCube MGT5100 FEC driver work

* Implement new mechanism to export U-Boot's functions to standalone
  applications: instead of using (PPC-specific) system calls we now
  use a jump table; please see doc/README.standalone for details

* Patch by Dave Westwood, 24 Jul 2003:
  added support for Unity OS (a proprietary OS)

* Patch by Detlev Zundel, 23 Jul 2003:
  add "imls" command to print flash table of contents

* Fix cold boot detection for log buffer reset

* Return error for invalid length specifiers with "cp.X" etc.

* Fix startup problem on MIPS

* Allow for CONFIG_SPLASH_SCREEN even when no explicit
  bitmap support is configured

* Patch by Bill Hargen, 18 Jul 2003:
  - fix endinaness problem in cpu/mpc824x/drivers/i2c/i2c1.c

* Patch by Denis Peter, 18 Jul 2003:
  - fix memory configuration for MIP405T
  - fix printout of baudrate for "loadb <loadaddr> <baudrate>"

* Cleanup of TQM82xx configurations; use "official" board types
  to make selection easier.

* Patch by Martin Krause, 17 Jul 2003:
  add delay to get I2C working with "imm" command and s3c24x0_i2c.c

* Patch by Richard Woodruff, 17 July 03:
  - Fixed bug in OMAP1510 baud rate divisor settings.

* Patch by Nye Liu, 16 July 2003:
  MPC860FADS fixes:
  - add MPC86xADS support (uses MPC86xADS.h)
  - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
    o PLPRCR changes
    o BRG changes (EXTAL/XTAL restricted to 10MHz)
    o don't trust gclk() software measurement by default, depend on
      CONFIG_8xx_GCLK_FREQ
  - add DRAM SIMM not installed detection
  - use more "correct" SDRAM initialization sequence
  - allow different SDRAM sizes (8xxADS has 8M)
  - default DER is 0
  - remove unused MAMR defines from FADS860T.h (all done in fads.c)
  - rename MAMR/MBMR defines to be more consistent. Should eventually
    be merged into MxMR to better reflect the PowerQUICC datasheet.

* Patch by Yuli Barcohen, 16 Jul 2003:
  support new Motorola PQ2FADS-ZU evaluation board which replaced
  MPC8260ADS and MPC8266ADS

======================================================================
Changes for U-Boot 0.4.4:
======================================================================

* Add support for IceCube board (with MGT5100 and MPC5200 CPUs)

* Add support for MGT5100 and MPC5200 processors

* Patch by Lutz Dennig, 15 Jul 2003:
  update for R360MPI board

======================================================================
Changes for U-Boot 0.4.3:
======================================================================

* Patches by Kshitij, 04 Jul 2003
  - added support for arm925t cpu core
  - added support for TI OMAP 1510 Innovator Board

* Patches by Martin Krause, 14 Jul 2003:
  - add I2C support for s3c2400 systems (trab board)
  - (re-) add "ping" to command table

* Fix handling of "slow" POST routines

* Patches by Yuli Barcohen, 13 Jul 2003:
  - Correct flash and JFFS2 support for MPC8260ADS
  - fix PVR values and clock generation for PowerQUICC II family
    (8270/8275/8280)

* Patch by Bernhard Kuhn, 08 Jul 2003:
  - add support for M68K targets

* Patch by Ken Chou, 3 Jul:
  - Fix PCI config table for A3000
  - Fix iobase for natsemi.c
    (PCI_BASE_ADDRESS_0 is the IO base register for DP83815)

* Allow to enable "slow" POST routines by key press on power-on
* Fix temperature dependend switching of LCD backlight on LWMON
* Tweak output format for LWMON

* Patch by Stefan Roese, 11 Jul 2003:
  - Fix bug in CONFIG_VERSION_VARIABLE.
  - AR405 config updated.
  - OCRTC/ORSG: bsp command added.
  - ASH405 bsp update.

======================================================================
Changes for U-Boot 0.4.2:
======================================================================

* Add support for NSCU board

* Add support for TQM823M, TQM850M, TQM855M and TQM860M modules

* Add support for Am29LV160ML, Am29LV320ML, and Am29LV640ML
  mirror bit flash on TQM8xxM modules

* Patch by Kenneth Johansson, 30 Jun 2003:
  get rid of MK_CMD_ENTRY macro; update doc/README.command

* Patch by Seb James, 30 Jun 2003:
  Improve documentation of I2C configuration in README

* Fix problems with previous log buffer "fixes"

* Fix minor help text issues

* "log append" did not append a newline

======================================================================
Changes for U-Boot 0.4.1:
======================================================================

* Fix some missing commands, cleanup header files
  (autoscript, bmp, bsp, fat, mmc, nand, portio, ...)

* Rewrite command lookup and help command (fix problems with bubble
  sort when sorting command name list). Minor cleanup here and there.

* Merge from "stable branch", tag LABEL_2003_06_28_1800-stable:
  - Allow to call sysmon function interactively
  - PIC on LWMON board needs delay after power-on
  - Add missing RSR definitions for MPC8xx
  - Improve log buffer handling: guarantee clean reset after power-on
  - Add support for EXBITGEN board (aka "genie")
  - Add support for SL8245 board

* Code cleanup:
  - remove trailing white space, trailing empty lines, C++ comments, etc.
  - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)

* Patches by Kenneth Johansson, 25 Jun 2003:
  - major rework of command structure
    (work done mostly by Michal Cendrowski and Joakim Kristiansen)

======================================================================
Changes for U-Boot 0.4.0:
======================================================================

* Patches by Robert Schwebel, 26 Jun 2003:
  - csb226 configuration updated
  - credits for logodl port updated
  - innokom configuration updated
  - logodl tree update, still with coding style inconsistencies
  - added OCM for ppc405 warning to README

* Patch by Pantelis Antoniou, 25 Jun 2003:
  update NetVia with V2 board support

* Header file cleanup for ARM

* Patch by Murray Jensen, 24 Jun 2003:
  - make sure to use only U-boot provided header files
  - fix problems with ".rodata.str1.4" section as used by GCC-3.x

* Patch by Stefan Roese, 24 Jun 2003:
  - Update esd ASH405 board files.
  - Update esd DASA_SIM config file.
  - Add ping command to some esd boards.

* Patch by Yuli Barcohen, 23 Jun 2003:
  Update for MPC8260ADS board

* Patch by Murray Jensen, 23 Jun 2003:
  - cleanup of GCC 3.x compiler warnings

* Patch by Rune Torgersen, 4 Jun 2003:
  add large memory support for MPC8266ADS board

* Patch by Richard Woodruff, 19 June 03:
  - Enabled standard u-boot device abstraction for ARM
  - Enabled console device for ARM
  - Initilized bi_baudrate for ARM

* Patch by Bill Hargen, 23 Apr 2003:
  fix byte order for 824x I2C addresses (write op)

* Patch by Murray Jensen, 20 Jun 2003:
  - hymod update
  - cleanup (especially for gcc-3.x compilers)

* Patch by Tom Guilliams, 20 Jun 2003:
  added CONFIG_750FX support for IBM 750FX processors

* Patch by Devin Crumb, 02 Apr 2003:
  Fix clock divider rounding problem in drivers/serial.c

* Patch by Richard Woodruff, 19 June 03:
  - Fixed smc91c111 driver to sync with the u-boot environment
    (driver/smc91c111.c).
  - Added eth_init error return check in NetLoop (net/net.c).

* Patch by Ken Chou, 19 June 2003:
  Added support for A3000 SBC board (Artis Microsystems Inc.)

* Patches by Murray Jensen, 17 Jun 2003:
  - Hymod board database mods: add "who" field and new xilinx chip types
  - provide new "init_cmd_timeout()" function so code external to
    "common/main.c" can use the "reset_cmd_timeout()" function before
    entering the main loop
  - add DTT support for adm1021 (new file dtt/adm1021.c; config
    slightly different. see include/configs/hymod.h for an example
    (requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
    CFG_DTT_ADM1021 defined)
  - add new "eeprom_probe()" function which has similar args and
    behaves in a similar way to "eeprom_read()" etc.
  - add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
    function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
  - gdbtools copyright update
  - ensure that set_msr() executes the "sync" and "isync" instructions
    after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
  - 8260 I/O ports fix: Open Drain should be set last when configuring
  - add SIU IRQ defines for 8260
  - allow LDSCRIPT override and OBJCFLAGS initialization: change to
    config.mk to allow board configurations to override the GNU
    linker script, selected via the LDSCRIPT, make variable, and to
    give an initial value to the OBJCFLAGS make variable
  - 8260 i2c enhancement:
    o correctly extends the timeout depending on the size of all
      queued messages for both transmit and receive
    o will not continue with receive if transmit times out
    o ensures that the error callback is done for all queued tx
      and rx messages
    o correctly detects both tx and rx timeouts, only delivers one to
      the callback, and does not overwrite an earlier error
    o logic in i2c_probe now correct
  - add "vprintf()" function so that "panic()" function can be
    technically correct
  - many Hymod board changes

* Patches by Robert Schwebel, 14 Jun 2003:
  - add support for Logotronic DL datalogger board
  - cleanup serial line after kermit binary download
  - add debugX macro (debug level support)
  - update mach-types.h to latest arm.linux.org.uk master list.

* Patches by David Müller, 12 Jun 2003:
  - rewrite of the S3C24X0 register definitions stuff
  - "driver" for the built-in S3C24X0 RTC

* Patches by Yuli Barcohen, 12 Jun 2003:
  - Add MII support and Ethernet PHY initialization for MPC8260ADS board
  - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
    configuration word supplied by FPGA on some MPC8260ADS boards

* Patch by Pantelis Antoniou, 10 Jun 2003:
  Unify status LED interface

* Add support for DS12887 RTC; add RTC support for ATC board

* Patch by Nicolas Lacressonniere, 11 Jun 2003:
  Modifications for Atmel AT91RM9200DK ARM920T based development kit
  - Add Atmel DataFlash support for reading and writing.
  - Add possibility to boot a Linux from DataFlash with BOOTM command.
  - Add Flash detection on Atmel AT91RM9200DK
    (between Atmel AT49BV1614 and AT49BV1614A flashes)
  - Replace old Ethernet PHY layer functions
  - Change link address

* Patch by Frank Smith, 9 Jun 2003:
  use CRIT_EXCEPTION for machine check on 4xx

* Patch by Detlev Zundel, 13 Jun 2003:
  added implementation of the "carinfo" command in cmd_immap.c

* Fix CONFIG_NET_MULTI support in include/net.h

* Patches by Kyle Harris, 13 Mar 2003:
  - Add FAT partition support
  - Add command support for FAT
  - Add command support for MMC
  ----
  - Add Intel PXA support for video
  - Add Intel PXA support for MMC
  ----
  - Enable MMC and FAT for lubbock board
  - Other misc changes for lubbock board

* Patch by Robert Schwebel, April 02, 2003:
  fix for SMSC91111 driver

* Patch by Vladimir Gurevich, 04 Jun 2003:
  make ppc405 ethernet driver compatible with CONFIG_NET_MULTI option

* Patch by Stefan Roese, 05 Jun 2003:
  - PPC4xx: Fix bug for initial stack in data cache as pointed out by
    Thomas Schaefer (tschaefer@giga-stream.de). Now inital stack in
    data cache can be used even if the chip select is in use.
  - CFG_RX_ETH_BUFFER added to set the ethernet receive buffer count
    (see README for further description).
  - Changed config files of CONFIG_EEPRO100 boards to use the
    CFG_RX_ETH_BUFFER define.

* Add support for RMU board

* Add support for TQM862L at 100/50 MHz

* Patch by Pantelis Antoniou, 02 Jun 2003:
  major reconstruction of networking code;
  add "ping" support (outgoing only!)

* Patch by Denis Peter, 04 June 2003:
  add support for the MIP405T board

* Patches by Udi Finkelstein, 2 June 2003:
  - Added support for custom keyboards, initialized by defining a
    board-specific drv_keyboard_init as well as defining CONFIG_KEYBOARD .
  - Added support for the RBC823 board.
  - cpu/mpc8xx/lcd.c now automatically calculates the
    Horizontal Pixel Count field.

* Fix alignment problem in BOOTP (dhcp_leasetime option)
  [pointed out by Nicolas Lacressonnière, 2 Jun 2003]

* Patch by Mark Rakes, 14 May 2003:
  add support for Intel e1000 gig cards.

* Patch by Nye Liu, 3 Jun 2003:
  fix critical typo in MAMR definition (include/mpc8xx.h)

* Fix requirement to align U-Boot image on 16 kB boundaries on PPC.

* Patch by Klaus Heydeck, 2 Jun 2003
  Minor changes for KUP4K configuration

* Patch by Marc Singer, 29 May 2003:
  Fixed rarp boot method for IA32 and other little-endian CPUs.

* Patch by Marc Singer, 28 May 2003:
  Added port I/O commands.

* Patch by Matthew McClintock, 28 May 2003
  - cpu/mpc824x/start.S: fix relocation code when booting from RAM
  - minor patches for utx8245

* Patch by Daniel Engström, 28 May 2003:
  x86 update

* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
  add nand flash support to SXNI855T configuration
  fix/extend nand flash support:
  - fix 'nand erase' command so does not erase bad blocks
  - fix 'nand write' command so does not write to bad blocks
  - fix nand_probe() so handles no flash detected properly
  - add doc/README.nand
  - add .jffs2 and .oob options to nand read/write
  - add 'nand bad' command to list bad blocks
  - add 'clean' option to 'nand erase' to write JFFS2 clean markers
  - make NAND read/write faster

* Patch by Rune Torgersen, 23 May 2003:
  Update for MPC8266ADS board

* Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length
  instead CFG_MONITOR_LEN is now only used to determine  _at_compile_
  _time_  (!) if the environment is embedded within the U-Boot image,
  or in a separate flash sector.

* Cleanup CFG_DER #defines in config files (wd maintained only)

* Fix data abort exception handling for arm920t CPU

* Fix alignment problems with flash driver for TRAB board

* Patch by Donald White, 21 May 2003:
  fix calculation of base address in pci_hose_config_device()

* Fix bug in command line parsing: "cmd1;cmd2" is supposed to always
  execute "cmd2", even if "cmd1" fails. Note that this is different
  to "run var1 var2" where the contents of "var2" will NOT be
  executed when a command in "var1" fails.

* Add zero-copy ramdisk support (requires corresponding kernel support!)

* Patch by Kyle Harris, 20 May 2003:
  In preparation for an ixp port, rename cpu/xscale and arch-xscale
  into cpu/pxa and arch-pxa.

* Patch by Stefan Roese, 23 May 2003:
  - IBM PPC405EP port added.
  - CONFIG_UART1_CONSOLE added. If defined internal UART1 (and not
    UART0) is used as default U-Boot console. PPC4xx only!
  - esd ASH405 board added (PPC405EP based).
  - BUBINGA405EP board added (PPC405EP based - IBM Eval Board).
  - esd CPCI405AB board added.
  - esd PMC405 board added.
  - Update of some esd boards.

* Patch by Denis Peter, 19 Mai 2003:
  add support for the MIP405-3 board

* Patch by Dave Ellis, 22 May 2003:
  Fix problem with only partially cleared .bss segment

* Patch by Rune Torgersen, 12 May 2003:
  get PCI to work on a MPC8266ADS board; incorporate change to
  cpu/mpc8260/pci.c to enable overrides of PCI memory parameters

* Patch by Nye Liu, 1 May 2003:
  minor patches for the FADS8xx

* Patch by Thomas Schäfer, 28 Apr 2003:
  Fix SPD handling for 256 ECC DIMM on Walnut

* Add support for arbitrary bitmaps for TRAB's  VFD command;
  allow to pass boot bitmap addresses in environment variables;
  allow for zero boot delay

* Patch by Christian Geißinger, 19 May 2002:
  On TRAB: wait until the dummy byte has been completely sent

* Patch by David Updegraff, 22 Apr 2003:
  update for CrayL1 board

* Patch by Pantelis Antoniou, 21 Apr 2003:
  add boot support for ARTOS (a proprietary OS)

* Patch by Steven Scholz, 11 Apr 2003:
  Add support for RTC DS1338

* Patch by Rod Boyce, 24 Jan 2003:
  Fix counting of extended partitions in diskboot command

* Patch by Christophe Lindheimer, 20 May 2003:
  allow the use of CFG_LOADS when CFG_NO_FLASH is set

* Fix SDRAM timing on Purple board

* Add support for CompactFlash on ATC board
  (includes support for Intel 82365 and compatible PC Card controllers,
  and Yenta-compatible PCI-to-CardBus controllers)

* Patch by Mathijs Haarman, 08 May 2003:
  Add lan91c96 driver (tested on Lubbock and custom PXA250 board only)

* Fix problem with usage of "true" (undefined in current versions of bfd.h)

* Add support for Promess ATC board

* Patch by Keith Outwater, 28 Apr 2003:
  - Miscellaneous corrections and additions to GEN860T board specific code.
  - Added GEN860_SC variant to GEN860T.
  - Miscellaneous corrections to GEN860T documentation.
  - Correct duplicate entry in U-Boot CREDITS file.
  - Add GEN860T_SC entry in MAINTAINERS file.
  - Update CREDITS file with GEN860T_SC info.

* Update Smiths Aerospace addresses in MAINTAINERS file

* Fix error handling in hush's version of "run" command

* LWMON extensions:
  - Splashscreen support
  - modem support
  - sysmon support
  - temperature dependend enabling of LCD

* Allow booting from old "PPCBoot" disk partitions

* Add support for TQM8255 Board / MPC8255 CPU

======================================================================
Changes for U-Boot 0.3.1:
======================================================================

* Make sure Block Lock Bits get cleared in R360MPI flash driver

* MPC823 LCD driver: Fill color map backwards, to allow for steady
  display when Linux takes over

* Patch by Erwin Rol, 27 Feb 2003:
  Add support for RTEMS (this time for real).

* Add support for "bmp info" and "bmp display" commands to load
  bitmap images; this can be used (for example in a "preboot"
  command) to display a splash screen very quickly after poweron.

* Add support for 133 MHz clock on INCA-IP board

* Patch by Lutz Dennig, 10 Apr 2003:
  Update for R360MPI board

* Add new meaning to "autostart" environment variable:
  If set to "no", a standalone image passed to the
  "bootm" command will be copied to the load address
  (and eventually uncompressed), but NOT be started.
  This can be used to load and uncompress arbitrary
  data.

* Patch by Stefan Roese, 10 Apr 2003:
  Changed DHCP client to use IP address from server option field #54
  from the OFFER packet in the server option field #54 in the REQUEST
  packet. This fixes a problem using a Windows 2000 DHCP server,
  where the DHCP-server is not the TFTP-server.

* Set max brightness for MN11236 displays on TRAB board

* Add support for TQM862L modules

======================================================================
Changes for U-Boot 0.3.0:
======================================================================

* Patch by Arun Dharankar, 4 Apr 2003:
  Add IDMA example code (tested on 8260 only)

* Add support for Purple Board (MIPS64 5Kc)

* Add support for MIPS64 5Kc CPUs

* Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS

* Patch by Denis Peter, 04 Apr 2003:
  - update MIP405-4 board

* Patch by Stefan Roese, 4 Apr 2003:
  - U-Boot version environment variable "ver" added
    (CONFIG_VERSION_VARIABLE).
  - Changed PPC405GPr version from A to B.
  - Changed CPCI405 to use CTS instead of DSR on PPC405 UART1.

* Patches by Denis Peter, 03 April 2003:
  - fix PCI IRQs on MPL boards
  - fix two more un-relocated pointer problems

* Fix behaviour of "run" command:
  - print error message iv variable does not exist
  - terminate processing of arguments in case of error

* Patches by Peter Figuli, 10 Mar 2003
  - Add support for BTUART on PXA platform
  - Add support for WEP EP250 (PXA) board

* Fix flash problems on INCA-IP; add tool to allow bruning images  to
  flash using a BDI2000

* Implement fix for I2C Edge Conditions problem for all boards that
  use the bit-banging driver (common/soft_i2c.c)

* Patch by Martin Winistoerfer, 23 Mar 2003
  - Add port to MPC555/556 microcontrollers
  - Add support for cmi customer board with
    Intel 28F128J3A, 28F320J3A or 28F640J3A flash.

* Patch by Rick Bronson, 28 Mar 2003:
  - fix common/cmd_nand.c

* Patch by Arun Dharankar, 24 Mar 2003:
  - add threads / scheduler example code

* Add patches by Robert Schwebel, 31 Mar 2003:
  - add ctrl-c support for kermit download
  - align bdinfo output on ARM
  - csb226 board: bring in sync with innokom/memsetup.S
  - csb226 board: fix MDREFR handling
  - misc doc fixes / extensions
  - innokom board: cleanup, MDREFR fix in memsetup.S, config update
  - add BOOT_PROGRESS to armlinux.c

* Add CPU ID, version, and clock speed for INCA-IP

* Patches by Dave Ellis, 18 Mar 2003 for SXNI855T board:
  - fix SRAM and SDRAM memory sizing
  - add status LED support
  - add MAC address for second (SCC1) ethernet port

* Update default environment for TQM8260 board

* Patch by Rick Bronson, 16 Mar 2003:
  - Add NAND flash support for reading, writing, and erasing NAND
    flash (certain forms of which are called SmartMedia).
  - Add support for Atmel AT91RM9200DK ARM920T based development kit.

* Patches by Robert Schwebel, 19 Mar 2003:
  - use arm-linux-gcc as default compiler for ARM
  - fix i2c fixup code
  - fix missing baudrate setting
  - added $loadaddr / CFG_LOAD_ADDR support to loadb
  - moved "ignoring trailing characters" _before_ u-boot wants to
    print out diagnostics messages; removes bogus characters at the
    end of transmission

* Patch by John Zhan, 18 Mar 2003:
  Add support for SinoVee Microsystems SC8xx boards

* Patch by Rolf Offermanns, 21 Mar 2003:
  ported the dnp1110 related changes from the current armboot cvs to
  current u-boot cvs. smc91111 does not work. problem marked in
  smc91111.c, grep for "FIXME".

* Patch by Brian Auld, 25 Mar 2003:
  Add support for STM flash chips on ebony board

* Add PCI support for MPC8250 Boards (PM825 module)

* Patch by Stefan Roese, 25 Mar 2003:
  - PCI405 update.

* Patch by Stefan Roese, 20 Mar 2003:
  - CPCI4052 update (support for revision 3).
  - Set edge conditioning circuitry on PPC405GPr for compatibility
    to existing PPC405GP designs.
  - Clip udiv to 5 bits on PPC405 (serial.c).

* Extend INCAIP board support:
  - add automatic RAM size detection
  - add "bdinfo" command
  - pass flash address and size to Linux kernel
  - switch to 150 MHz clock

* Avoid flicker on the TRAB's VFD by synchronizing the enable with
  the HSYNC/VSYNC. Requires new CPLD code (Version 101 for Rev. 100
  boards, version 153 for Rev. 200 boards).

* Patch by Vladimir Gurevich, 12 Mar 2003:
  Fix relocation problem of statically initialized string pointers
  in common/cmd_pci.c

* Patch by Kai-Uwe Blöm, 12 Mar 2003:
  Cleanup & bug fixes for JFFS2 code:
  - the memory mangement was broken. It caused havoc on malloc by
    writing beyond the block boundaries.
  - the length calculation for files was wrong, sometimes resulting
    in short file reads.
  - data copying now optionally takes fragment version numbers into
    account, to avoid copying from older data.
  See doc/README.JFFS2 for details.

* Patch by Josef Wagner, 12 Mar 2003:
  - 16/32 MB and 50/80 MHz support with auto-detection for IP860
  - ETH05 and BEDBUG support for CU824
  - added support for MicroSys CPC45
  - new BOOTROM/FLASH0 and DOC base for PM826

* Patch by Robert Schwebel, 12 Mar 2003:
  Fix the chpart command on innokom board

* Name cleanup:
  mv include/asm-i386/ppcboot-i386.h include/asm-i386/u-boot-i386.h
  s/PPCBoot/U-Boot/ in some files
  s/pImage/uImage/  in some files

* Patch by Detlev Zundel, 15 Jan 2003:
  Fix '' command line quoting

* Patch by The LEOX team, 19 Jan 2003:
  - add support for the ELPT860 board
  - add support for Dallas ds164x RTC

* Patches by David Müller, 31 Jan 2003:
  - minimal setup for CardBus bridges
  - add EEPROM read/write support in the CS8900 driver
  - add support for the builtin I2C controller in the Samsung s3c24x0 chips
  - add support for MPL's VCMA9 (Samsung s3c2410 based) board

* Patch by Steven Scholz, 04 Feb 2003:
  add support for RTC DS1307

* Patch by Reinhard Meyer, 5 Feb 2003:
  fix PLPRCR/SCCR init sequence on 8xx to allow for
  changes of EBDF by software

* Patch by Vladimir Gurevich, 07 Feb 2003:
  "API-compatibility patch" for 4xx I2C driver

* TRAB fixes / extensions:
  - Restore VFD brightness as saved in environment
  - add support for Fujitsu flashes
  - make sure both buzzers are turned off (drive low level)

* Patches by Robert Schwebel, 06 Mar 2003:
  - fix bug in BOOTP code (must use NetCopyIP)
  - update of CSB226 port
  - clear BSS segment on XScale
  - added support for i2c_init_board() function
  - update to the Innokom plattform

* Extend support for redundand environments for configurations where
  environment size < sector size

* Patch by Rune Torgersen, 13 Feb 2003:
  Add support for Motorola MPC8266ADS board

* Patch by Kyle Harris, 19 Feb 2003:
  patches for the Intel lubbock board:
  memsetup.S - general cleanup (based on Robert's csb226 code)
  flash.c - overhaul, actually works now
  lubbock.c - fix init funcs to return proper value

* Patch by Kenneth Johansson, 26 Feb 2003:
  - Fixed off by one in RFTA calculation.
  - No need to abort when LDF is lower than we can program it's only
    minimum timing so clamp it to what we can do.
  - Takes function pointer to function for reading the spd_nvram. Usefull
    for faking data or hardcode a module without the nvram.
  - fix other user for above change
  - fix some comments.

* Patches by Brian Waite, 26 Feb 2003:
  - fix port for evb64260 board
  - fix PCI for evb64260 board
  - fix PCI scan

* Patch by Reinhard Meyer, 1 Mar 2003:
  Add support for EMK TOP860 Module

* Patch by Yuli Barcohen, 02 Mar 2003:
  Add SPD EEPROM support for MPC8260ADS board

* Patch by Robert Schwebel, 21 Jan 2003:
  - Add support for Innokom board
  - Don't complain if "install" fails
  - README cleanup (remove duplicated lines)
  - Update PXA header files

* Add documentation for existing POST code (doc/README.POST)

* Patch by Laudney Ren, 15 Jan 2003:
  Fix handling of redundand environment in "tools/envcrc.c"

* Patch by Detlev Zundel, 28 Feb 2003:
  Add bedbug support for 824x systems

* Add support for 16 MB flash configuration of TRAB board

* Patch by Erwin Rol, 27 Feb 2003:
  Add support for RTEMS

* Add image information to README

* Patch by Stefan Roese, 18 Feb 2003:
  CPCIISER4 configuration updated.

* Patch by Stefan Roese, 17 Feb 2003:
  Fixed bug in ext. serial clock setup on PPC405 (since PPC440 port).

* Patch by Stefan Roese, 13 Feb 2003:
  Add "pcidelay" environment variable (in ms, enabled via
  CONFIG_PCI_BOOTDELAY).
  PCI spec 2.2 defines, that a pci target has 2^25 pci clocks after
  RST# to respond to configuration cycles (33MHz -> 1s).

* Fix dual PCMCIA slot support (when running with just one
  slot populated)

* Add VFD type detection to trab board

* extend drivers/cs8900.c driver to synchronize  ethaddr  environment
  variable with value in the EEPROM

* Patch by Stefan Roese, 10 Feb 2003:
  Add support for 4MB and 128MB onboard SDRAM (cpu/ppc4xx/sdram.c)

* Add support for MIPS32 4Kc CPUs

* Add support for INCA-IP Board

======================================================================
Changes for U-Boot 0.2.2:
======================================================================

* Add dual ethernet support on PM826

* Add support for LXT971 PHY on PM826

* Patch by Tord Andersson, 16 Jan 2003:
  Fix flash sector count for TQM8xxL

* Fix I2C EEPROM problem on ICU862 board (would only write the first
  16 bytes out of each 32 byte block)

======================================================================
Changes for U-Boot 0.2.1:
======================================================================

* Add support for V37 board
  (patch by Jón Benediktsson, 11 Dec 2002)

* Update baudrate in bd_info when it gets changed

* Add watchdog trigger points while waiting for serial port
  (so far only 8xx -- needed on LWMON with 100ms watchdog)

* Improve command line tool to access the U-Boot's environment
  (figuration of the utility, using a config file)

* Add single quote support for (old) command line parser

* Switch LWMON board default config from FRAM to EEPROM;
  in POST, EEPROM shows up on 8 addresses

======================================================================
Changes for U-Boot 0.2.0:
======================================================================

* Use 1-byte-read instead of -write for iprobe() function
  Add i2c commands to PM826 config

* extend I2C POST code: check for list on known addresses

* Improve log buffer code; use "loglevel" to decide which messages
  to log on the console, too (like in Linux); get rid of "logstart"

* Add command line tool to access the U-Boot's environment
  (board-specific for TRAB now, to be fixed later)

* Patch by Hans-Joerg Frieden, 06 Dec 2002
  Fix misc problems with AmigaOne support

* Patch by Chris Hallinan, 3 Dec 2002:
  minor cleanup to the MPC8245 EPIC driver

* Patch by Pierre Aubert , 28 Nov 2002
  Add support for external (SIU) interrupts on MPC8xx

* Patch by Pierre Aubert , 28 Nov 2002
  Fix nested syscalls bug in standalone applications

* Patch by David Müller, 27 Nov 2002:
  fix output of "pciinfo" command for CardBus bridge devices.

* Fix bug in TQM8260 board detection - boards got stuck when board ID
  was not readable

* Add LED indication for IDE activity on KUP4K board

* Fix startup problems with VFD display on TRAB

* Patch by Pierre Aubert, 20 Nov 2002
  Add driver for Epson SED13806 graphic controller.
  Add support for BMP logos in cfb_console driver.

* Added support for both PCMCIA slots (at the same time!) on MPC8xx

* Patch by Rod Boyce, 21 Nov 2002:
  fix PCMCIA on MBX8xx board

* Patch by Pierre Aubert , 21 Nov 2002
  Add CFG_CPM_POST_WORD_ADDR to make the offset of the
  bootmode word in DPRAM configurable

* Patch by Daniel Engström, 18 Nov 2002:
  Fixes for x86 port (mostly strings issues)

* Patch by Ken Chou, 18 Nov 2002:
  Fix for natsemi NIC cards (DP83815)

* Patch by Pierre Aubert, 19 Nov 2002:
  fix a bug for the MII configuration, and some warnings

* Patch by Thomas Frieden, 13 Nov 2002:
  Add code for AmigaOne board
  (preliminary merge to U-Boot, still WIP)

* Patch by Jon Diekema, 12 Nov 2002:
  - Adding URL for IEEE OUI lookup
  - Making the autoboot #defines dependent on CONFIG_AUTOBOOT_KEYED
    being defined.
  - In the CONFIG_EXTRA_ENV_SETTINGS #define, the root-on-initrd and
    root-on-nfs macros are designed to switch how the default boot
    method gets defined.

* Patch by Daniel Engström, 13 Nov 2002:
  Add support for i386 architecture and AMD SC520 board

* Patch by Pierre Aubert, 12 Nov 2002:
  Add support for DOS filesystem and booting from DOS floppy disk

* Patch by Jim Sandoz, 07 Nov 2002:
  Increase number of network RX buffers (PKTBUFSRX in
  "include/net.h") for EEPRO100 based boards (especially SP8240)
  which showed "Receiver is not ready" errors when U-Boot was
  processing the receive buffers slower than the network controller
  was filling them.

* Patch by Andreas Oberritter, 09 Nov 2002:
  Change behaviour of NetLoop(): return -1 for errors, filesize
  otherwise; return code 0 is valid an means no file loaded - in this
  case the environment still gets updated!

* Patches by Jon Diekema, 9 Nov 2002:
  - improve ADC/DAC clocking on the SACSng board to align
    the failing edges of LRCLK and SCLK
  - sbc8260 configuration tweaks
  - add status LED support for 82xx systems
  - wire sspi/sspo commands into command handler; improved error
    handlering
  - add timestamp support and alternate memory test to the
    SACSng configuration

* Patch by Vince Husovsky, 7 Nov 2002:
  Add "-n" to linker options to get rid of "Not enough room for
  program headers" problem

* Patch by David Müller, 05 Nov 2002
  Rename CONFIG_PLL_INPUT_FREQ to CONFIG_SYS_CLK_FREQ
  so we can use an already existing name

* Patch by Pierre Aubert, 05 Nov 2002
  Hardware relatied improvments in FDC boot code

* Patch by Holger Schurig, 5 Nov 2002:
  Make the PXA really change it's frequency

* Patch by Pierre Aubert, 05 Nov 2002
  Add support for slave serial Spartan 2 FPGAs

* Fix uninitialized memory (MAC  address)  in  8xx  SCC/FEC  ethernet
  drivers

* Add support for log buffer which can be passed to Linux kernel's
  syslog mechanism; used especially for POST results.

* Patch by Klaus Heydeck, 31 Oct 2002:
  Add initial support for kup4k board

* Patch by Robert Schwebel, 04 Nov 2002:
  - use watchdog to reset PXA250 systems
  - added progress callbacks to (some of the) ARM code
  - update for Cogent CSB226 board

* Add support for FPS860 board

* Patch by Guillaume Alexandre,, 04 Nov 2002:
  Improve PCI access on 32-bits Compact PCI bus

* Fix mdelay() on TRAB - this was still the debugging version with
  seconds instead of ms.

* Patch by Robert Schwebel, 1 Nov 2002:
  XScale related cleanup (affects all ARM boards)

* Cleanup of names and README.

======================================================================
Notes for U-Boot 0.1.0:
======================================================================

This is the initial version of "Das U-Boot", the Universal Boot Loader.

It is based on version 2.0.0 (the "Halloween Release") of PPCBoot.
For information about the history of the project please see the
PPCBoot project page at http://sourceforge.net/projects/ppcboot

======================================================================