blob: e50f3ead13b2bec17138f6d99813359d99f900c8 [file] [log] [blame]
Luka Kovacicd4cc1792020-07-23 10:56:37 +02001// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Device Tree file for CRS326-24G-2S board
4 *
5 * Copyright (C) 2016 Allied Telesis Labs
6 * Copyright (C) 2020 Sartura Ltd.
7 *
8 * Based on armada-xp-db.dts
9 *
10 * Note: this Device Tree assumes that the bootloader has remapped the
11 * internal registers to 0xf1000000 (instead of the default
12 * 0xd0000000). The 0xf1000000 is the default used by the recent,
13 * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
14 * boards were delivered with an older version of the bootloader that
15 * left internal registers mapped at 0xd0000000. If you are in this
16 * situation, you should either update your bootloader (preferred
17 * solution) or the below Device Tree should be adjusted.
18 */
19
20/dts-v1/;
21#include "armada-xp-98dx3236.dtsi"
22#include "armada-xp-crs326-24g-2s-u-boot.dtsi"
23
24/ {
25 model = "CRS326-24G-2S+";
26 compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
27
28 chosen {
29 stdout-path = "serial0:115200n8";
30 bootargs = "console=ttyS0,115200 earlyprintk";
31 };
32
33 aliases {
34 spi0 = &spi0;
35 };
36
37 memory {
38 device_type = "memory";
39 reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
40 };
41};
42
43&L2 {
44 arm,parity-enable;
45 marvell,ecc-enable;
46};
47
48&devbus_bootcs {
49 status = "okay";
50
51 /* Device Bus parameters are required */
52
53 /* Read parameters */
54 devbus,bus-width = <16>;
55 devbus,turn-off-ps = <60000>;
56 devbus,badr-skew-ps = <0>;
57 devbus,acc-first-ps = <124000>;
58 devbus,acc-next-ps = <248000>;
59 devbus,rd-setup-ps = <0>;
60 devbus,rd-hold-ps = <0>;
61
62 /* Write parameters */
63 devbus,sync-enable = <0>;
64 devbus,wr-high-ps = <60000>;
65 devbus,wr-low-ps = <60000>;
66 devbus,ale-wr-ps = <60000>;
67};
68
69&uart0 {
70 status = "okay";
71};
72
73&uart1 {
74 status = "okay";
75};
76
77&i2c0 {
78 clock-frequency = <100000>;
79 status = "okay";
80};
81
82&usb0 {
83 status = "okay";
84};
85
86&spi0 {
87 status = "okay";
88
89 spi-flash@0 {
90 #address-cells = <1>;
91 #size-cells = <1>;
92 compatible = "spi-flash", "jedec,spi-nor";
93 reg = <0>; /* Chip select 0 */
94 spi-max-frequency = <108000000>;
95 m25p,fast-read;
96
97 partition@u-boot {
98 reg = <0x00000000 0x001f0000>;
99 label = "u-boot";
100 };
101 partition@u-boot-env {
102 reg = <0x001f0000 0x00010000>;
103 label = "u-boot-env";
104 };
105 partition@ubi1 {
106 reg = <0x00200000 0x00e00000>;
107 label = "ubi1";
108 };
109 };
110};